GENERAL MAINTENANCE
Item
Windshield washer fluid Check that there
is adequate fluid
in the tank
Reference item in MA section
-
Engine coolant level Check the coolant level when the -
engine is cold
Radiator and hoses Check the front of the radiator and
clean off any dirt, insects,
leaves, etc , that may have
accumulated Make sure the hoses have no cracks, deforrna-
tion, rot or loose connections
Brake and clutch fluid levels Make sure that the brake and CHECKING CLUTCH FLUID LEAKS
clutch fluid
levels are between the "MAX" and "MIN" lines INSPECTING BRAKE LINES & HOSES
on the reservoir
Engine drwe belts Make sure that no belt if frayed, worn,
cracked or oily CHECKING AND ADJUSTING DRIVE BELT
Engine oil level Check the level on the dipstick after park- -
ing the vehicle on a level spot and turning off the engine
Power steering fluid level Check the level on the dipstick
when the fluid
is cold and the engine is turned off
0 CHECKING POWER STEERING FLUID LEVEL
Automatic transmission fluid level Check the level on the CHECKING AUTOMATIC TRANSMISSION
dipstick after putting the selector
level in "P" with the FLUID LEVEL
engine idling
Exhaust system Make sure there are no loose supports, 0 INSPECTING EXHAUST SYSTEM
cracks or holes If the sound of the exhaust seems unusual
or there
is a smell of exhaust fumes, immediately locate the
trouble and correct
it
Underbody The underbody is frequently exposed to corro-
sive substances such as those used on icy roads or to control
dust
It is very impOrtant to remove these substances, other-
wise rust will form on the floor pan, frame, fuel lines and
around
the exhaust system. At the end of winter, the
underbody should be thoroughly flushed with plain water,
being careful to clean those
areas where mud and dirt can
easily accumulate.
Fluid leaks Check under the vehicle for fuel, oil, water or
other fluid
leaks after the vehicle has been parked for a 0 INSPECTING MANUAL TRANSMISSION OIL
while.
Water dripping from the air conditioner after use is 0 INSPECTING AUTOMATIC TRANSMISSION FLUID
normal. If you should notice
any leaks or gasoline fumes
are evident, check for
the cause and correct it immediately.
0 CHECKING CLUTCH FLUID LEAKS
0 INSPECTING DIFFERENTIAL GEAR OIL
0 INSPECTING FRONT AXLE AND SUSPENSION
0 INSPECTING REAR AXLE AND SUSPENSION
0 INSPECTING BRAKE LINES & HOSES
0 CHECKING POWER STEERING LINE & HOSES
PARTS
PARTS
MA-6
ENGINE MAINTENANCE
Changing Ei
WARNING:
To avoid the danger of being scalded, never
attempt to change the coolant when the engine
is hot.
1 Before drainmg engine coolant
1) Except auto air conditioner equipped models
Slide temperature control lever to
"HOT"
position
SMAJ81 A
2) Auto air conditioner equipped models
Turn ignition switch
"ON" and set temperature
at maximum
Then turn ignition switch
"OFF".
SMA782A
2 Open radiator cap and drain plug to drain
engine coolant.
SMA703A
ine Coolant
3 Open drain plug on right side of cylinder block
to drain coolant from cylinder block.
4 Close drain plug and drain cock securely Then,
fill radiator with water and warm up engine
5 Stop engine and wait until it cools down.
6. Repeat procedure from step 2 through step 5
two or three times.
7 Drain water and fill radiator and engine with
new coolant up to
filler opening Follow
instructions attached to anti-freeze container
for
mixing ratio of anti-freeze to water.
Slowly pour coolant through coolant fryer neck
to allow air in system to escape.
8. Fill reservoir tank up to "MAX" level Then
close radiator cap.
9. Run the engine at approximately 2,000 rpm
for about one minute.
IO. Stop the engine and after it cools down, refill
the radiator
and engine with coolant up to the
filler opening. Fill the reservoir tank with
coolant up to "MAX" level.
Coolant capacity:
VG30E engine
VG30ET engine
10.5 P (11-1/8 US qt, 9-1/4 Imp qt)
11.0 P (1 1-5/8 US qt, 9-5/8 Imp qt)
MA-1 0
ENGINE MAINTENANCE
Checking Exhaust Gas Sensor (Cont'd)
Preparation
When checking exhaust gas sensor, make sure that the following are
in good order
0 Battery
0 Hoses
Engine oil and coolant levels
E C C S. components
E.C C S. harness and connectors
Oil filler cap and oil level gauge
Checking procedure
START
Stan engine and warm UP until water
temperature indicator Points
IO middle
of gauge
I +
Run engine at about 2.000 rpm for abut
2 minutes under noload
I
E C C S control unit is turned fully
referring to MIXTURE RA
MA-1 6
