
GENERAL MAINTENANCE
General maintenance includes those items which should be checked during the normal day-today operation
of the vehicle They are essential if the vehicle is to continue operating properly The owners can perform the
checks and inspections themselves
or they can have their N ISSAN/DATSUN dealers do them for a nominal
charge
Item Reference item in MA section
OUTSIDE THE VEHICLE
Tires Check the pressure with
a gauge periodically when at
a service station, including the spare, and adjust to the
specified pressure
if necessary Check carefully for damage,
cuts
or excessive wear.
Wheel nuts When checking the tires, make sure no nuts are TIRE REPLACEMENT
missing, and check for any loose nuts Tighten if neces-
sary
0 CHECKING TIRE CONDITION
Wheel nut
Tire rotation Tires should be rotated every 24.000 km 0 TIRE ROTATION
(15,000 miles).
Wheel alignment and balance If the vehicle should pull to 0 CHECKING TIRE CONDITION
either side while driving on
a straight and level road, or if
you detect uneven or abnormal tire wear, there may be a 0 CHECKING WHEEL ALIGNMENT
need for wheel alignment
If the steering wheel or seat 0 WHEEL INSPECTION
vibrates
at normal highway speeds, wheel balancing may be
needed.
Abnormal tire wear
Windshield glass Check for abrasions or scratches -
Windshield wiper blades Check for cracks or wear if they do
not wipe properly
Doors and engine hood Check that all doors and the engine
hood operate smoothly
as well as the trunk lid and back
hatch.
Also ensure, that all latches lock securely Lubricate
if necessary. Make sure that the secondary latch keeps the
hood from opening when the primary latch
is released
-
0 LUBRICATING LOCKS, HINGES AND HOOD
LATCH
INSIDE THE VEHICLE
The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, clean-
ing
the vehicle, etc.
turn signal lights. and other lights are all operating properly
and installed securely.
Also check headlight aim.
Lights Make sure that the headlights,stop lights. tail lights. -
Warning lights and buaerslchimes Make sure that all warn-
ing lights and buzzers/chimes are operating properly
Horn Make sure it operates properly -
Windshield wrper and washer Check that the wipers and
washer operate properly and that the wipers do not streak

CHASSIS AND BODY MAINTENANCE
Checking Rear Axle and
Rear Suspension Parts (Cont'd)
(3) Check axle and suspension parts for wear,
cracks or damage
0 Check shock absorber for oil leakage or dam-
age
- SMA726A
--Checking Drive Shaft
Check boot and drive shaft for cracks, wear, dam-
age or grease leakage.
SM A743 A
,Checking Front Wheel Alignment -
PRELIMINARY INSPECTION
Tire pressure
Wheel bearing axial play
Suspension ball joint
Steering linkage and connections
Shock absorber operation
Tighten each front axle and suspension parts
Measure vehicle height (Unladen).
The vehicle must be on a level surface both
fore and
aft, and transversely.
Repair or replace the damaged portion or
parts
Steering gear housing looseness at frame
" U n I aden "
Fuel tank, radiator and engine oil tank all full
Spare tire, lack, hand tools, mats in position
CAMBER, CASTER AND KINGPIN
INCLINATION
Camber, caster and kingpin inclination are preset
at
factory and cannot be adjusted
Camber.
-35 to 55'
Caster :
5"50 - 7"3Q
Kingpin inclination:
12"15' - 13"45'
TOE-IN
1 Mark a base line across the tread
After lowering front of vehicle, move it up and
down
to eliminate friction.
MA-23
4

CHASSIS AND BODY MAINTENANCE
Checking Front Whe
2 Measure toe-in
Liner parallel to center line of body-
Toe-in = A - 8
SMA124 Front
Toe-in:
1 - 3 mm (0.04. 0.12 in)
6-16
3 Town can be adjusted by varying the length
of steering side rods
SMA727A
"A" standard dimension:
37.5 mm (1.476 in)
inner rocket
SST274A
Alignment (Cont'd)
FRONT WHEEL TURNING ANGLE
a Rotate steering wheel all the way right and
left, measure turning angle on inner wheel
SMA127
Turning angle.
Full turns
Inside
Outside
35" - 39"
27"
~ 31"
Toe-out turn (Insideloutside):
22"30/20"
If it is not within speclfication, check rack
stroke.
Refer to section
ST
Rack stroke
r Rack
Tie-rod inner i. socket Tie-rod inner socket
,Rack -1
Unit mm (in) (Cvlander end housing ndel SST223A
MA-24
.

CHASSIS AND BODY MAINTENANCE
Checking Rear
PRELIMINARY INSPECTION
0 Tire pressure.
0 Wheel bearing axial play
0 Shock absorber operation.
0
0 Measure vehicle height (Unladen)
Tighten each rear axle and suspension part
The vehicle must be on a level surface both
fore and
aft, and laterally
Repair or replace the damaged portion or parts
0
"Unladen"
Fuel tank, radiator and engine oil tank all full
Spare
tire, jack, hand tools, mats in position
CAMBER
Camber
is preset at factory and cannot be adjusted
Camber:
-1"55'tO -25'
TOE-IN
1. Mark a base line across the tread
SMA123
nee1 Alignment
2 Measure toe-in
~~ner parallel to center Ime of body-
Toe-in = A - B
, Front 8 SMA124
Toe-in:
-2 to 2 mm (-0.08 to 0.08 in)
3 Toein can be adjusted by inside of rear arm
bushing pins
Unit
Tobl" TObOltl Max 9 6 10 3781 Max 9.6 (0.378)
When performing toe adjustment, always set the
cams in the same position on the right and left rear
arm bushing pins.
MA-25
,,_l

SERVICE DATA AND SPECIFICATIONS (S.D.S.)
Used belt deflection
Limit
Adlusted deflecraon
Engine Maintenance
INSPECTION AND ADJUSTMENT
st deflec. TIon Of
new belt Pedal free Play "A"
Alternator
1 -3 IO M -0 121
Arr conditioner I 16 I 9-11 I 7-9 compressor (0631 1035 0431 (028-0351
ADDlted pushtng force I 98 N 110 kg, 22 Ibl
21
10831 Power steering 011 pump
Oil capacity
13.16 10-13
1051 .0631 (039-0511 ~~
unlt P IUS qt. Imp qtl
Wheel alignment IUnladenI
Camber
degree
Caster degree
-35' to 55'
5*50.7"30
Coolant capacity Unlt &? IUS qt. Imp qtl
Wlth 041 falter
Wtthout
001 filter
VG30E & VG30ET
4
0 (4-1 /4, 3-1/21
3 3 13-1/2.
2 7/81
Spark plug
VG30E
I VG30E I VO3OET
105 111-1/8, 91/41
Front wheel turning angle Toe-out turns
Inner wheelIOufer wheel
degree
Plug uaD I 10- 1 1 mm 10039-OW3 in1
22"30'/20'
altitude I 20*2'/650t50 I 20t2'/650f50
standard iype
Hot type
Cola woe
condmon
VG30ET I 20 f 2"/700 f 50 I 20 + 2'/650 t 50
BCPR6ES.11 BCPR6E-11
BCPRSES.11 BCPRSE-11
BCPR7ES.11 BCPR7E-11
TIGHTENING TORQUE
U"lt Nm kg-m ft-lb
Full turns Inner wheel degree
Outer wheel degree
Or1 pan drain plug 29-39 30-40 22-29
Spark plug 20-29 20-30 14-22
Fuel hme clamps 10-15 010-015 07-11
35" .39"
27" .31'
-Chassis and Body Maintenance-
INSPECTION AND ADJUSTMENT
Clutch
Unlt mm 11nI
Pedal height "H" I 195 - 205 I7 68.8 071
Front axle and front suspension
Wheel bearmg preload
IAr measured at wheel hub bolt1 6 86.14 61
With used parts N Ikg, Ibl 1 1 67.7 75 IO 17-079.037- 1741
Kingpin mclination degree I 12'15'- 13'45
degree I 6'- 16
Out 3 (0 0361 - In 3 (0 0361 Side lip IReference datal mm/m lin/ftl
37 5 I1 476) Standard side rod length "A" mm bnl
* On power steering models, wheel turning force la1 circumference
afsteeringwheellof98-147NI10-15kg.22-33lblwith
engtne at idle
Rear axle and rear suspension
Camber degree I -1-55' fa -25
mm (4") I -2 to 2 1-0 08 to 0 081 Toe-,"