
GENERAL MAINTENANCE 
Item  Reference item in MAsection 
Windshield  defroster  Check that the air comes  out of the 
defroster  outlets  properly and in sufficient  quantity when 
operating  the heater  or 
air conditioner 
Rear view  mirror  Make sure that it is secure 
- 
- 
Sun visors  Make  sure that they can be moved freely  and are 
secure 
Steering  wheel Check  that it has the specified  free play  Be 
sure  to check  for changes  in the  steering  condition,  such 
as 
excessive free  play,  hard steering or strange  noises 
- 
Specification 
Free 
play Less  than 35 mm (1 38 in) 
Seats  Check  front seat position  controls  such as seat adjust- - 
ters, seatback  recliner, etc to ensure  they operate  smoothly 
and  that 
all latches  lock securely in every  position  Check 
that the head  restraints  move up and down  smoothly  and 
that 
the locks  (if so equipped)  hold securely  in all latched 
positions  Check that the latches  lock securely  for folding- 
down  rear seatbacks 
Seat belts Check that all parts  of the  seat  belt system  e g 
buckles,  anchors and retractors  operate  property and  ANCHORS, RETRACTORS  AND ADJUSTER 
smoothly  Check the belt  webbing  for cuts,  fraying,  wear or 
damage 
INSPECTING  SEAT BELTS,  BLUCKLES, 
Accelerator  pedal  Check the pedal  for smooth  operation - 
and make  sure the pedal  does not catch  or require  uneven 
effort 
Clutch  pedal Make sure the pedal  operates  smoothly  and 
check  that 
it has the proper  free travel 
ADJUSTING  CLUTCH  PEDAL HEIGHT  AND 
FREE PLAY 
Brakes  Check that the brake  does not  pull  the vehicle  to 
one  side when  applied 
Brake  pedal  Check the pedal for smooth  operation  and 
make  sure 
it has the  proper  distance  under it when  de- 
pressed  fully Check  the brake booster  function 
CHECKING BRAKE PEDAL DEPRESSED  HEIGHT 
0 CHECKING BRAKE BOOSTER  FUNCTION 
Parking brake Check  that the lever  has the proper  travel and 
confirm that  your vehicle 
is held securery on a fairly  steep 
hill with only the parking  brake applied 
0 CHECKING  PARKING BRAKE 
Automatic transmission  "Park"  mechanism  Check that the 
lock  release  button  on the  selector  lever operates  properly 
and  smoothly 
On a fairly  steep hill check  that your  vehicle 
is held securely  with the selector  lever in the  "P"  wsition 
without 
aDDlvina anv  brakes 
UNDER  THE HOOD  AND VEHICLE 
The maintenance items listed here should  be checked  periodically e  g each  time you check  the engine  oil or refuel 
MA-5  

GENERAL MAINTENANCE 
Item 
Windshield  washer fluid Check  that  there 
is adequate  fluid 
in the tank 
Reference  item in MA  section 
- 
Engine  coolant level Check the coolant level when  the - 
engine is cold 
Radiator  and hoses  Check  the front  of  the  radiator  and 
clean  off any  dirt,  insects, 
leaves, etc , that may  have 
accumulated  Make sure the hoses  have no cracks,  deforrna- 
tion,  rot or loose  connections 
Brake  and clutch  fluid levels Make sure that the brake  and CHECKING  CLUTCH  FLUID LEAKS 
clutch  fluid 
levels are between  the "MAX"  and "MIN"  lines INSPECTING  BRAKE LINES & HOSES 
on  the  reservoir 
Engine  drwe belts Make  sure that  no belt  if frayed,  worn, 
cracked  or oily CHECKING  AND ADJUSTING  DRIVE BELT 
Engine oil level Check the level on the  dipstick  after park- - 
ing the  vehicle on a level  spot and turning off the engine 
Power  steering  fluid level Check the level on the  dipstick 
when  the fluid 
is cold  and the engine is turned off 
0 CHECKING  POWER STEERING  FLUID LEVEL 
Automatic  transmission  fluid level Check the level on the CHECKING  AUTOMATIC  TRANSMISSION 
dipstick  after  putting the selector 
level in "P" with  the  FLUID LEVEL 
engine  idling 
Exhaust system Make sure there  are no loose supports, 0 INSPECTING  EXHAUST SYSTEM 
cracks  or holes  If the  sound  of the  exhaust  seems unusual 
or  there 
is a smell  of exhaust  fumes, immediately  locate the 
trouble  and correct 
it 
Underbody  The underbody is frequently  exposed to corro- 
sive substances  such as those used on icy  roads or to control 
dust 
It is very  impOrtant  to remove these  substances, other- 
wise  rust will form  on the  floor  pan, frame,  fuel lines  and 
around 
the exhaust system. At  the  end  of winter,  the 
underbody  should  be thoroughly  flushed with plain  water, 
being  careful  to clean  those 
areas where mud and dirt can 
easily  accumulate. 
Fluid leaks Check  under the vehicle  for fuel,  oil, water  or 
other  fluid 
leaks after the vehicle has been  parked  for a 0 INSPECTING  MANUAL TRANSMISSION  OIL 
while. 
Water dripping from the  air conditioner after use is 0 INSPECTING  AUTOMATIC  TRANSMISSION  FLUID 
normal.  If you  should  notice 
any leaks or gasoline  fumes 
are  evident,  check for 
the cause and correct it immediately. 
0 CHECKING  CLUTCH  FLUID LEAKS 
0 INSPECTING  DIFFERENTIAL  GEAR OIL 
0 INSPECTING  FRONT AXLE AND SUSPENSION 
0 INSPECTING  REAR AXLE  AND SUSPENSION 
0 INSPECTING  BRAKE LINES & HOSES 
0 CHECKING  POWER STEERING  LINE & HOSES 
PARTS 
PARTS 
MA-6  

CHASSIS AND BODY MAINTENANCE 
Checking  Exhaust  System 
Check  exhaust pipes, muffler  and mounting  for 
proper  attachment, 
leaks, cracks,  damage, loose 
connections, chafing and  deterioration 
W SMA211A 
-Checking Clutch Operation - 
Check clutch pedal  height, free travel and smooth 
omration 
Floor carpet 
Dash insulator 
H Pedal free height A Pedal free travel 
SMA558A 
Pedal  free height "H": 
Pedal  free travel "A": 
195.205 mm (7.68 - 8.07 in) 
1 ~ 3 rnrn (0.04 - 0.12 in) 
If necessary,  adjust clutch  pedal free height and 
pedal  free travel.  Refer 
to section CL 
-Checking  Clutch Fluid Level- 
If fluid level is extremely low, check  clutch  system 
for  leaks 
Changing  Clutch Fluid 
Refill with recommended  brake fluid "DOT 
3" 
Do not reuse  drained brake  fluid 
Be careful not to splash  brake fluid on painted 
areas. 
Drain the  fluid in the  air  bleeder valve 
SCLOO9 
Refill  until the new  fluid  comes  out in the  air 
bleeder  valve 
Use same procedure  as in bleeding hydraulic 
system  to refill  the fluid 
Refer to section CL 
MA-I 7 
,  

CHASSIS AND BODY  MAINTENANCE 
Checking  Clutch System 
Check clutch fluid lines for proper  attachment, 
leaks, chafing,  deterioration, etc 
SMA741A 
Checking M/T Oil 
1. Check manual  transmission  for signs  of leakage 
SMA429A 
2 Check  oil level 
LFiller plug 
SMAl03 
Never start engine  while checking oil level. 
Changing M/T Oil 
n 
Drain plug 
Oil capacity: 
FS5W71C and BW T-5 (FS5R90A) 
1.9 Liters (4 US pt, 3-3/8 Imp pt) 
MA-1 8  

CHASSIS AND BODY  MAINTENANCE 
1 Check  automatic  transmission  for signs  of 
leakage 
SMA430A 
2 Check  under following  conditions 
(1) Place selector lever in "P" (PARK)  position 
and 
idle engine 
(2) Maintain  fluid temperature at 50 to 80°C 
(122 to 176'F) 
(3) Add  oil, if necessary 
Use only A/T fluid  having "DEXRON" 
SMA559A 
L/T Fluid 
3 Check  automatic  fluid condition. 
Check  fluid  for  contamination  to determine 
condition  of automatic  transmission  If fluid 
is very  dark  or  smells burned,  the frictional 
material  (clutches,  band, 
etc ) may need  re- 
placement 
Check flwd for COntaminarlOn 
r? 
,w 
Check fluid for smell SMA107 
MA-19  

SERVICE DATA AND SPECIFICATIONS (S.D.S.) 
Used belt deflection 
Limit 
Adlusted deflecraon 
Engine  Maintenance 
INSPECTION  AND ADJUSTMENT 
st deflec. TIon Of 
new belt Pedal  free Play "A" 
Alternator 
1 -3 IO M -0 121 
Arr conditioner I 16 I 9-11 I 7-9 compressor (0631  1035 0431 (028-0351 
ADDlted  pushtng force I 98 N 110 kg, 22 Ibl 
21 
10831 Power steering 011 pump 
Oil capacity 
13.16  10-13 
1051  .0631  (039-0511  ~~ 
unlt P IUS qt. Imp qtl 
Wheel alignment IUnladenI 
Camber 
degree 
Caster degree 
-35' to 55' 
5*50.7"30 
Coolant  capacity Unlt &? IUS qt. Imp qtl 
Wlth 041 falter 
Wtthout 
001 filter 
VG30E & VG30ET 
4 
0 (4-1 /4, 3-1/21 
3 3  13-1/2. 
2 7/81 
Spark plug 
VG30E 
I VG30E I VO3OET 
105  111-1/8,  91/41 
Front wheel turning  angle Toe-out turns 
Inner wheelIOufer  wheel 
degree 
Plug uaD I 10-  1 1 mm  10039-OW3 in1 
22"30'/20' 
altitude I 20*2'/650t50 I 20t2'/650f50 
standard iype 
Hot type 
Cola woe 
condmon 
VG30ET I 20 f 2"/700 f 50 I 20 + 2'/650 t 50 
BCPR6ES.11 BCPR6E-11 
BCPRSES.11 BCPRSE-11 
BCPR7ES.11 BCPR7E-11 
TIGHTENING  TORQUE 
U"lt Nm kg-m ft-lb 
Full turns Inner wheel  degree 
Outer wheel  degree 
Or1 pan drain plug 29-39 30-40 22-29 
Spark plug 20-29 20-30 14-22 
Fuel hme clamps 10-15 010-015 07-11 
35" .39" 
27"  .31' 
-Chassis  and Body Maintenance- 
INSPECTION  AND ADJUSTMENT 
Clutch 
Unlt mm 11nI 
Pedal height "H" I 195 - 205 I7 68.8 071 
Front  axle and front  suspension 
Wheel  bearmg  preload 
IAr measured at wheel hub bolt1 6 86.14  61 
With used parts N Ikg, Ibl 1 1 67.7  75 IO 17-079.037-  1741 
Kingpin mclination degree I 12'15'- 13'45 
degree I 6'- 16 
Out 3 (0 0361 - In 3 (0 0361 Side lip IReference  datal mm/m lin/ftl 
37 5 I1 476) Standard side rod  length "A" mm bnl 
* On power steering models,  wheel turning force la1 circumference 
afsteeringwheellof98-147NI10-15kg.22-33lblwith 
engtne at idle 
Rear axle and rear  suspension 
Camber  degree I -1-55' fa -25 
mm (4") I -2 to 2 1-0 08 to 0 081 Toe-,"  

SERVICE DATA AND SPECIFICATIONS  (S.D.S.) 
Chassis and  Body  Maintenance  (Cont'd) 
Parklng brake 
[at 
pulling force 196 N 120 kg. 44 Ibll 
Number  of notches 
Brake Unit mm (mi 
8-9 
CL28V 2 0 10 0791 
Pad wear limit -+--- CL14H 2 0 10 0791 
Difference  between right 
and  left lateral 
runout mm (In1 
Rotor  repair limit CL14H  9 0 (0 3541 
Pedal free hetght  "h" 
Mi7 model 182.192  (7 17.7 56) 
Less than 0 5 (0 0201'1 
0 2 10 0081'2 
Pedal depressed height 
[Under  force 
of 490 N 150 kg. 110 Ibl with englne running1 More than 90 13 541 
Wheel  and tire 
Tire  inflation 
Proper  tire pressures  are  shown  on the  tire  placard affixed 
to the driver's  side center  Dillar of vehicle. 
80 km/h 150 MPH) 
28 psi 1200 kPa1 
Spare  tire C78-14 
T~re pressure should  be checked when  tires are COLD 
Wheel rim lateral and 
radial  runout 
1 
Less than 1 0 10 0391'1 0 5 (0 020)*2 mm 11nl 
Wheel  balance IMaximvm allowable  gr 102) 10 10 35) 
unbalance at rim  flange1 
I 5-601018-2121 Spmng 5 10 181 Tire balancing weight  gr 1oz) 
I 
*1 Steel wheel *2 Aluminum wheel 
TIGHTENING TORQUE 
Unit  Nm 
Clutch 
Pedal stopper  lock  nut 
Clutch  switch  lock 
nut 
Master cyhnder  push 8. 12 
rod lock nut 
Manual  transmission 
9 1 - 11 8 
12 - 15 
Drain and filter  plugs 
FS5W71C 25 - 34 
FS5R90A  20.34 
Differential carrier 
Front axle and front 
S"Spe"Sl0" 
Side  rad lock  nut 
Drain and flller  plugs 39 - 59 
14.17 
Brake Air bleeder value 7-9 
Stop lamp swmh 12-15 
lock nut 
Brake  booster  input 
rod  lock 
nut 
16 - 22 
Wheel and tire 
Wheel nut 78.98 
kg-m  ft-lb 
093.12 67-87 
12-15 9-11 
08-12 58-87 
25-35 18-25 
20-35 14-25 
4-6 29 - 43 
14-17 10-12 
07-09 51-65 
12-15 9-11 
16-22  12-16 
80.100 58-72 
MA-37