Page 1 of 21

. . c-, :
Service Manual
MONTERO
1984
FOREWORD
This Sk-vice Manual has been prepared with the latest
service information available at the time of publi-
cation. It is subdivided into various group categories
-and each section contains diagnosis, disassembly,
repair, and installation procedures along with com-
plete specifications and tightening references. Use of
this manual will aid in properly performing any
servicing necessary to maintain or restore the high
levels of performance and reliability designed into
these outstanding vehicles.
WE SUPPORT l VOLUNTARY TECHNICIAN
CERTIFICATION
THROUGH
.&tsubishi Motors Corporation reserves the right to make changes in
Zesign or to make additions to or improvements in its products without
mposing any obligations upon itself to install them on its products
.reviously manufactured. Introduction . , . .,......,..........
0 Lubrication and Maintenance . . . . . . . . .
2
3
5
6 Front Suspension ..................
RearAxle:. ......................
Brakes - Service and Parking .........
Clutch ..........................
7
8 Cooling ...........................
Electrical System ..................
9
11 Engine ...........................
Exhaust System .....................
13 Body and Frame Alignment . . . . . . . . . .
14 Fuel System . , . . . . . . . . . . .,. . . . . . . . .
16 Propeller Shaft and Universal Joints . . .,.
17 Rear Suspension . . . . . . . . . . . . . . . . . . .
19 Steering - Power . . . . . . . . . . . . . . ., . . .
21 Manual
Transmission - Automatic .,........
22 Wheels and Tires. . . , . . . , , . . . . . . . . . .
23 Body and Sheet Metal , . . . . . . . . . . . . .
24 Heaters and Air-conditioning . . . . . . . . .
25 Emission Control Systems . . . . . . . . . . .
GROUP INDEX Alphabetical Index
0 1983 Mitsubishi Motors Corporation Printed in Japan
Page 6 of 21
i 1
I
VEHICLE IDENTIFICATION
I
ENGINE AND TRANSMISSION.MODEL
Vehicle model Engine model Tradsmission
mod11
L042GNJLF
I
L042GNJLH
L042GNULF
L042GNULH
L042GVNJLF G54B KM 145-O-THQ
L042GVNJLH
L042GVNULF
L042GVNULH
1 .
M42GVKJLF
L042GVKJLH
L042GVKULF G54B KM146 ~
L042GVKULH
I
BODY COLOR CODE
,Exterior code Body color
Two-tone
B93B91X13
C38C19X13
H74H80X13
A R79R78X13
W44W42X13
X04X21H80 Black/Light blue (M
Black/Brown (Metal
Black/Silver (Metalk
.Black/Red
Black/White
Veliet black/Silver (
6
i
efi
lit
id)
I
:“:
T sllic)
>
etallic) :
Page 13 of 21

TOWING AND HOISTING
TOWING AND HOISTING
The MONTERO can only be towed from the front with
conventional sling-type equipment and tow chain &th
grab hooks.
If a vehicle is towed from the rear, use a tow dolly.
A lumber spacer (4” x 4” x 55” wood beam) should be
placed forward of under guard and under towing hook/
shipping tie down hook.
Then, attach J-hook to the lower arm.
A safety chain system must be used. This system must be
completely independent of the primary lifting and’ towing
attachment. Care must be taken in the installation of safety
chains to insure they do not cause damage to bumper,
painted surfaces or lights.
Lifting-Ground Clearance
Towed vehicle should be raised until wheels are a minimum
of 10 cm (4 in.) from the ground. Be sure there is
adequate ground clearance at the opposite end of the vehicle,
especially when towing over rough terrain or when crossing
sharp rises such as curbs. If necessary, ground clearance can
be increased by removing the wheels from the lifted end of
the disabled vehicle and carrying the lifted end closer, to the
ground. A 20 cm (8 in.) ground clearance must be maintained
between brake drums and ground.
Front Towing Pickup
The vehicle may be towed on its rear wheels for extended
distances, provided the parking brake is released.
Make certain the transmission remains in “NEUTRAL”.
Safety Precautions
The following precautions should be taken when towing the
vehicle.
1. Remove exhaust tips and any other optional equipment,
that interface with the towing sling. Padding (heavy shop
towel or carpeting) should be placed between the towing
sling cross bar and any painted surfaces, and bumper
surfaces.
2. A safety chain system completely independent of the pri-
mary lifting and towing attachment must be used.
3. Any loose or protruding parts of damaged vehicle such as
hoods, doors, fenders, trim, etc., should be secured prior
to moving the vehicle.
4. Operator should refrain from going under a vehicle unless
the vehicle is adequately supported by safety stands.
5. Never allow passengers to ride in a towed vehicle.
6. State and local rules and regulations must be followed
when towing a vehicle.
13
Page 17 of 21

GENERAL DATA AND SPECIFICATIONS
Description
LO42G NJLF/H
NULFIH VNJLF/H ViULF/H VNULF/H VKULF/H
Engine
Model No.
Type
Number of cylinders
Bore
Stroke
Piston displacement
Compression ratio
Firing order
Basic ignition timing
Transmission & transfer case
Model No.
Type
Gear ratio
Transmission
Transfer case
Final ring gear ratio G54B
In-line OHC
4
9i.l mm (3.59 in.)
98.0 mm (3.86 in.)
2,555 cm3 (155.9 CID)
8.2
-3 l-3-4-2
7”BTDC + 2”
KM145 KM145
S-speed 5-speed
manual manual KM145
5-speed
manual KM146 KM145 KM146
3-speed 5-speed 3-speed
automatic manual automatic
1st 3.740 3.740, 3.740 2.745 3.740 2.745
2nd 2.136 2.136 2.136 1.543 2.136 1.543
3rd 1.360 1.360 1.360 1 .ooo 1.360 1 .OOO
4th 1 .ooo 1 .ooo 1.000 - 1 .ooo
5th 0.856 0.856 0.856 - 0.856 -
Reverse 3.578 3.578 3.578 2.214 3.578 2.214
High
Low 1 .ooo 1 .ooo 1 .ooo 1 .ooo 1 .ooo 1 .ooo
1.944 1.944 1.944 1.944 1.944 1.944
4.625 4.625 4.625 4.222 4.625 4.222
4.875* 4.875” 4.875* 4.625* 4.875” 4.625*
Clutch
Type
Chassis
Tire size
Front suspension
Type
Spring constant (Wheel position)
Rear suspension
Type
Spring constant
At load of 1 ,OOO-2,500 N
(220-551 lbs.)
At load of 4,670-8,870 N
(1,030-1,955 lbs.)
Brakes
Type Front
Rear
Power steering
Gear type
Gear ratio
Fuel tank capacity Dry single Dry single Dry single
disc & disc & disc &
diaphragm diaphragm diaphragm -
spring spring spring Dry single
disc & ‘,
diaphragm -
spring
215SR15
Wishbone compression type
22 N/mm (123 lbs./in.)
Asymmetrical semi-elliptic leaf spring
24 N/mm (134 lbs ./in.)
56 N/mm (3 14 Ibs./in.)
Disc
Drum
(Leading and trailing)
Integral type (Recirculating ball nut).
16.4
60 liters (15.9 U.S. ga.lJ13.2 Imp. gal.)
*Optional for Federal (not available in California).
17