1981 CHEVROLET MONTE CARLO tow

Downloaded from www.Manualslib.com manuals search engine SECTION 3
IN CASE OF ,EM,ERGENCY
See also "Engine ,ExhausIGas Caution (Carbon Monoxide)" at the beginning
of
"Starting and Operating ." Section 2 of this manual.
FOUR.WAYHAZARD WARNING FLASHER
• Use the hazard warning flasher to warn other drivers any time your vehicle
becomes a traffic hazard , day or night
• 'Avoid stopping 00 the roadway if. possible .
•
Turn on ·the haz,ard warning flasherb{ pushing In the button (inSide the COllar) located on the cOlumn just'behind the steering whee ,l. The 'flasher wUl work with1he ignition either off or on,
",'
• The turn SIgnalS ao not wOl1< wnen me hazard flasher is on,
• 'On·$ome·,V:!>tJiC~S;,j\tj:l~i9[~~",~}S pushed down,the fights will not
flash; they will stay on utitiltne 'Brake iS,'released , ,
•
To turn off the flasher . pull the buttOflcoliar out.
EMERGENCY STARTING
NOtICE:. Do not-~.h oi tow this -Y~le_to stlW1 it. Under some cond~: "this-may· d.~a,ge the catalytic e,onverter or'other:~rt~ofthe vehicle.
Before attempting to' start. the vehicle with the jump starting 'procedUre which
tollows, check the condition of the vehicle battery cables to battery connections
to
8$sure that, theye,e free of corro~i(>n an,d tight, n they are not. correct the, condition . tJrn off the radio and ,'ot1\ and attempt to start the engine ,
II your vehicle has a discharged , battery. it can
be started ,bY' using energy from anotheL battery-,a,,'prQCedure 'called "jump starting ,'" ,
NOTICE; II yiK'-haVe yoUr 'vehiclt"'jU4 .flirted by. "";kie _Uon or 'wrecker. be sur. iheequlpm8ntu~ ,is 12-yott and' ~":' neg.tlve ground. DO NOT · ALLOW THE USE OF 2A-VOL t 'CHAR'GINO .EOlHPMENT,,_ uSingsucti equipment cn cau .. serioUl damage to the e~ar system Of efre%nic~rta in your V'8hide._
Jump Starting
CAUTION: Better •• produce expJOlive gnea , corroaive acid and "vela of electrical current high enough 10 cause burns. To IeUen the chance of person.1 injury or property -damage, the Instruction, below must be fOllowed ex.ctly.
"

Downloaded from www.Manualslib.com manuals search engine 'I'
'"
JACKING INSTRUCTIONS OJ PARK ON A Lf;VEL SUR'ACE AND SET PARKING BRAKE FIRMLY, [!] SET_ AUTOMATIC TRANSMISSION IN "PARK" (MANUAL TRANSMISSION IN RIEVERH,_
...0 DO NOT TAa 'tOUI ~ THIOUGH ..... NJroMATtc CAl-WASH WIT" O)III#ACT WAIl INSTAU.ID . THI .... HtC&I' .... T OIl CAIIGHT WHICH COULD .I$UlT ... NONJn D.t.MAGI. .... _._ ...... __ ........ __ •• __ ._ .. II'>
AERO BACK COUPE MODELS Irutan Jack using Upper Hole Location.
LEVER IN DOWN POSITION
-~~ ... /~ ..
TIGHTEN
( " §. = .. :Mt .. : . 0 II .OZ
ill TURN_ON THE HAZARD W.ARNING FLASHER •. o REMOVE JACKING TOOLS AND PARE T IRE FROM STOWAGE. AREA. [!] aLOCK FRONT AND REAR OF WHEEL DIAGONALLY OPPOSITE WHEEL BEING REMOVED IIE"O .. I: OPERATING JACK. [!) LOOSEN, BUT DO NOT REM,OVe: WHEEL NUTS BV TURNING WRENCH COUNTIERCLQCI ~
' ' L.OAD PAO . N.UT.S IN A C IUSS·C ROSS SEQUENCII.Y TURNING WRENCH CLOCKWISE,. ---~ -~ACK RATCHET MECHANISM SHOULD.II OILED AFTER EACH USE.
"RAMII~~
JACK

Downloaded from www.Manualslib.com manuals search engine ~
I , ,
INSTRUCTIoN
SPECIAL I . WIRE WHEEL COV~R REMOVAL ,t
ENCH
REMOVE
MEDALLION
VIEWA
LOCK
BOLT • BRACKET MEDALLION
VIEW B
WIRE WHEEL COVER WITH SPECIAL LOCK KIT A REMOVAL
1. To gain access to th.~ wheel cover lock bolt, remove the medallion from the center of the wheel cover by prying out from retainer using blade end -
, of special wrench that is stowed . in the glove box. (See View A)
2. Usi'ng the socket end of the special wrench, remove foC;k bolt. (~e View B)
3. The wheel cover can now be removed and reinstalled as 'necessary .
INSTALLATION
1. After the'cover 'is in place, install the lock bolt and tighten securely.
2. Align clips on the back afthe medallion with slots in the cover and snap
into place.
'NOTE : If the specia l wrench is ever lost or misplaced , a duplicate can be 0b­tained by mailing the registration card (located in the glove bo)t) 'to the address shown on the card. Remember the lock bolt can onty be removed with the special wrench and the wheel cover cannot be taken· off without first removing the lock bolt.

Downloaded from www.Manualslib.com manuals search engine JACKING
CAUTION
To help avoid personal injury:
• Follow air jacking and stowage instructions.
• Use jack only for lifting this vehicle during wheel change.
• Never get . beneath the vehicle, start or run engine while vehicle is supported by jack.
• Always securely restol" sp!.re tire (orflattire) and all jac king equipment.
Wheel Nut Torque .
CAUTION: As soon as possible atter installing a wheel -AND at the intervals stated
In Section 'S of the Maintenanc," Schedule folder --have a technician tighten wheel nuts with a torque wrench to the specifications shown in "Specifications," Section 7 of this manual.
Wheel nuts should be tightened alternately and evenly to the correct torque.
Never use oil or grease on studs Of nuts.. Jrnproperty tightened wheel nuts could eventually aUow the whee! to come off while the veNeta Is moving, -po$$rbty causing
personal injury , damage and/or klss of c_ontrol. (Also see the "Replacement Fasteners" Caution In "Service and Maintenance ," Section 5 01 this m8nu81 regarding the danger of mixing metric and custom,sry fasteners. And, see the "Replacement Fasteners " Caution
under "Tires" in the same seclion regarding the importance of obtaining good metal-to­
metsl contact.)
Stowage ·of. Tire . and .!aC;.k,. . .
CAUTION: Always securely restow the spare tire assembfy (or nat tire), all jacking equipm ent, any tire inflator, and any covers or doors, using the means provided. This will help keep such things from being thrown about-and injuring people In the vehicta d.Ufing a sudden maneuver or an accident.
Before stowing
the tire, be sure:to clean the tire well 01 anything that would keep the tlr. from resting on the bOttom of the well. To stow the jack, place its lever in the "UP" position and. move the handle back and forth until the column is ·secure in the receiver (see Illustration). If these steps are not taken, the tire or lack may push against the trunk lid so thai the trunk lid cannot seal tightly. This _ may allOw carbon monoxide from the '. exhaust system -to get _inside tiMt c • . ttvougtl the trunk. (See "Engine -Exhaust Gas Caution (CaroonMonoxkle) " al the beginning of "Starting and Operating,'; Section 2 of this manual .)
Extended Vehicle Storage
If you plan to store your vehicle over an extended periOd of time, certain steps
should be taken to give it maximum protection.
It is recommended that you
write the Chevrolet Motor Division , General Motors Corporation, Consumer
Relations Dept., Warren , Michigan
48090, for detailed instructions on how to
prepare your vehicle for storage .
3-7

Downloaded from www.Manualslib.com manuals search engine Towing
Proper equipment .must be used to prevent damage to vehicles during any
towing. State (Provincial in Canada) and local laws which apply to vehicles in
tow must be
followed. Get detailed towing instructions from your dealer.
Your vehicle
may be towed on all four wheels, at speeds less than 35 mph (60
km/h), for distances up to 50 miles (80 kilometers), provided the driveline and
steering are normally operable. For such towing, the steering must be unlocked, transmission in neutral and the· parking brake released. Connect to
main structural parts of the vehicle. Do NOT attach to bumpers or brackets.
Remember also that power assist for brakes and steering will not be available when the engine is off.
If the vehicle is to be towed by a wrecker, use only equipment designed for this purpose, following the instructions of the wrecker manufacturer. A safety Chain
system must be used for all towing.
FREEING VEHICLE FROM SAND, MUD, SNOW OR
ICE
If your vehicle gets stuck in sand, mud, snow or ice, move the shift lever on automatic transmission models from "0" (Drive) to "R" (Reverse) in a repeat
pattern.
Apply a light pressure to the accelerator pedal while the transmission is in gear. Remove your foot from the accelerator while shifting. Do not race
the engine. For best traction, avoid spinning the wheels. Incorrect rocking of your vehicle while it is stuck may result in damage to vehicle components.
CAUTION: Do not spin the wheels faster than 35 mph (55 km/h). Personal injury and
damage (inCluding tire, transmission and/or rear axle failure) may result from excessive
wheel spinning.
If the vehicle remains stuck after several rocking attempts, seek other
assistance. Also see the Notice under '(Automatic Transmissions" in "Steering
Column-Controls," Section 2 of this manual.
3-9

Downloaded from www.Manualslib.com manuals search engine 4. If a ring forms after spot cleaning, clean the entire area IMMEDIATELY.
5. Follow specific instructions on cleaner labels.
Cleaning General Soilage Or Water Spots From Fabric-Type
Trim With Foam-Type
Clealler
GM Multi-Purpose Powdered Cleaner is excellent for this type of cleaning and
for cleaning panel sections where small cleaning rings may be left from spot
cleaning.
• Vacuum the area thoroughly to remove any loose dirt.
• ALWAYS clean a full trim assembly or complete trim section. Mask
surrounding trim along stitch or
welt lines.
• Mix Multi-Purpose Powdered Cleaner in strict accordance with directions on the container label. Mix in proportion for smaller quantities.
• USE SUDS ONLY ON A CLEAN SPONGE OR SOFT BRISTLE BRUSH. DO NOT SATURATE FABRIC OR .RUB IT HARSHLY WITH A BRUSH.
IMMEDIATELY AFTER CLEANING, WIPE OFF EXCESS SUDS WITH A
SLIGHTLY DAMP ABSORBENT TOWEL OR CLOTH.
• IMPORTANT -IMMEDIATELY AFTER WIPING, FORCE-DRY THE FABRIC WITH AN AIR HOSE, HEAT DRYER OR HEAT LAMP. (Use caution with
heat dryer or lamp to help prevent fabric damage.)
• When trim materials with a sheen or luster finish are dry, wipe fabric lightly with a soft, dry, clean cloth to restore its sheen or luster~
.. ~~.P~t CI~.aning Fabric-Type Trim With Solvent Type Cleaner
Bef~~~ t~yirlgtb'remove aspotQf stain from fabric, determine as accurately as you can the type and age of the spot or stain: Some spots or slains can be
removed with water or mild soap solution (see "Removal of Specific Stains").
Spots or stains should always be removed as soon as possible.
Some types of stains or sOilage,such as lipstick, inks and grease, are very
difficult (sometimes impossible) to completely remove. When cleaning this type
of stain·or soilage, be sure not· to enlarge thesoiled'area.
GM Fabric Cleaner (Solvent Type) is excellent for spot cleaning grease, oil, or
fat stains.
• Gently scrape excess stain from the trim material with a clean, DULL knife
or scraper.
USE VERY LlTILE CLEANER, light pressure and clean cloths
(preferably cheesecloth). Cleaning should start at the outside of the stain,
"FEATHERING" toward the center. Keep changing to a clean section of
the cloth.
• When you clean a stain from fabric, immediately dry the area with an air hose, heat dryer, or heat lamp to help prevent a cleaning ring. (Use caution
with heat dryer or lamp to prevent fabric damage).
• If a ring forms, immediately repeat the cleaning operation over a slightly
larger area with emphasis
on "FEATHERING" towards its center. If ring
remains, mask off surrounding trim sections and clean the entire affected
area with
GM Multi-Purpose Powdered Cleaner (as described under
"Cleaning General Soilage or Water Spots with Foam Type Cleaner").

Downloaded from www.Manualslib.com manuals search engine FUEL CAP
The fuel cap is.behind the. rear license plate.
NOTICE: tt you need: to repWce the fuel cap, use only a cap with these same features as specifie your dealer.
The fuel tank filler cap has a "screw-on ratcheting type" feature .
• _ To remove -rotate cap counterclockwise to clear the inside of the filler
neck. This will allow any residual pressure to escape .
_ To install -reverse this procedure and tighten cap securely until a
"ratcheting ". clicking sound is heard indicating cap is on properly.
CATALYTIC CONVERTER
.Ttle .cal;!ly:tic converter is an emission control device added to the exhaust system,' to reduce exhaust gas pollutants. The converter contains
a ceramic material coated with noble metal catalysts. To prevent contamination
of the catalysts , unleaded gasol;"" must be used . Unleaded gasoline also
reduces spark plug louling. exhaust system corrosion and engine oil
deterioration.
The catalytiC converter requires the use of unleaded gasoline. Using leaded gasoline wilt cause --the converter to lose its effectiveness as an
emission control device. Leaded gasoline will also damage the Computer
Command Control, system oxygen sensor, which could affect emission control,
fuel economy . and drivability.
~,~.,y..'~,","~ ... :..., To help 'prevent damage:
1. Keep your engine properly maintained . Engine malfunctions involving the electrical, carburetion or ignition systems may result in unusually high
catalytic con verter and exhaust . sy~tem temperatures which, under
extreme malfunctioning conditions·, may ignite interior floor:"'covering
materials above the converter. Do not keep driving your vehicle if you
detect engine misfire, noticeable loss of performance ,or other unusual operating conditions. Instead. have it serviced promptly.
A properly maintained
engine will help avoid malfunctions that could damage
the converter.
~ will also help provide good emission control and fuel economy.
See the Maintenance Schedule , folder for information on inspecling and
maintaining the engine. exhaust system. and other components. .
2. Do not drive through or Idle or park your vehicle over combustible
materials, such as grass or leaves_ They could touch the hot exhaust
system and ignite.
3. Do not push or tow this vehiCle to start it. This may result in unusually
high catalytic converter and exhaust system temperatures which under
extreme conditions may ignite interior floor -covering material above the
converter.
Pushing or towing to start can also damage · the catalytic
converter itself.
Disregarding these
instructions could damage the cataly:tic converter. the
vehicle, or nearby property.
5-2

Downloaded from www.Manualslib.com manuals search engine Choosing Oil Viscosity
Engine oil viscosity (thickness) has an effect on fuel economy. Lower viscosity engine oils can provide· better fuel economy; however, higher temperature
weather cOl1ditions. require· higher viscosity .engine. oils· for satisfactory
lubrication.
It is recommended that you select an oil not only of the proper quality and
viscosity, but also. a fuel-saving product.· These oils can be found in Chevrolet dealer serviGe departments, service stati()ns and other retail stores. They are
identified by words such as: "Energy Conserving," "Energy Saving," "Conserves Gasoline," "Gas Saving," "Gasoline Saving," "Friction
Reducing," "Improved Gasoline Mileage," "Improved Fuel Economy" or "Fuel
Saving."
The following chart lists the engine oil viscosities recommended for the
tE3lT1per~ture range you·. expecLbefore your next oil change. For temperatures
above -18'C '(O'F), SAE 10W-30 is the preferred viscosity grade. If cold­weather starting problems are encountered at temperatures below -18'C
(O'F), SAE 5W-30 viscosity oils m?-y be required.
Change Intervals
The oil and oil filter change intervals for your engine are based on the use of SF-quality oils and high-quality filters such as AC oil filters. Using oils other
than
SF-quality, or oil and/or filter change intervals longer than recommended, could reduce engine life.
Damage to engines due to improper maintenance or use of incorrect oil quality
'andl0r"'vi$9()~ity}s .~ot covered by the Chevrolet new car warranties.
Your engine WEIS filled with a high-quality engine oil when it was built. You do
not have to change this oil before the first recommended change
interval.
•
Severe Service-Change the oil and oil filter every 3,000 miles (4 800
kilometers) or three months (whichevefcbmes first) if one or more of the following "severe service" conditions is often encountered:
• Driving in dusty areas.
• Towing a trailer.
• Frequent idling or idling for long periods.
• Oriving 4 miles (6 kilometers) or less in freezing weather.
• Change the oil and oil filter as soon as possible after driving in a dust storm.
~ Norma! Service-If your engine is not a turbo-charged engine and your
normal driving does not include one of the above "severe service" conditions, change the oil every 7,500 miles (12 000 kilometers) or 12
months, whichever comes first. Change the oil
filter at the first oil change,
then every other
oil change, if mileage (7,500 miles or 12 000 kilometers)
determines when you change the oil. If time (12 months) determines when
you change the oil, change the filter with every oil change.
• If you have a turbocharged engine, it is VERY IMPORTANT to change the
oil and oil filter EVERY 3,000 miles (4 800 kilometers).
5-4