1980 SKODA 120 LS torque

ii
i ENGINE
Model
- for Skodo 105 S ond 105
L
- for Skodo 12o L
- for Skodo 120 LS
Type
Number of cylinders
Cylinder orrongement
Cooling
Swept volume
- Skodo 105 S ond 105 L
- Skodo 12O L ond
120 LS
Bore
- Skodo 105 S ond 105 L
- Skodo 120 L
ond 120 LS
Stroke
Compression rotio
- Skodo 105 S, 105 L ond 120 L
- Skodo 120 LS
Engine power
output to CSN ond DIN
- Skodo 105 S ond 105 L
- Skodo 12O L
- Skodo 120 LS
Moximum torque
- Skodo 105 S ond 105 L
- Skodo 120 L
- Skodo 120 LS
Fuel -
recommended octone number
- Skodo 105 S,
- Skodo 120 Ls
Corburettor type
Fuel lift pump
type
CLUTCH
Type
Control
GEARBOX
Type Speeds
Geor rotios -
1st-speed geor
2nd-speed geor
3rd-speed geor
4th-speed geor
reverse geor Skodo 742.10 Engine No/l
Skodo
742.12 Engine No/2
Skodo 742.12x Engine
No/9
four-stroke, spork-ignltion,
corburettor engine with overheod volves
4 in line
pump-circuloted ontifreeze,
thermostotic temperoture control
1,046 c. c.
1,174 c.c.
68 mm
72 mm
72 mm
8.5:1
9.5:1
33.9 kW (46
h. p.)
ot 4,800 r.
P. m.
38.3 kW (52
h. p.)
ot 5,(X)0 r. p.
m.
42.7 kW (58
h. p.)
ot 5,2(X) r. p.
m.
74.5 Nm ot 3,000 r.p.m.
85.2 Nm ot 3,000 r.p.m.
90.2 Nm ot 3,250 r.p.m.
90 minimum 95 minimumduol, twostoge, downdrought
nrodel JIKOV 32 EDSR
diophrogm pump, model
JIKOV MF
dry, single-plote, with direct
disengogement
hydroulic
with helicol
spur geas
4 forword ond 1 reverse, synchrolock on the
1st-, 2nd-,
3rd-, ond 4th-speed geors
3.8
2.12 1.41
0.96 3.27
105 L ond
12O L
18

il
tli
GEARBOX. FINAL
DRIVE
Connection DimensionsTightening
torque Nmt)
Nuts of cosing clomping bolts .
Nut of primory shoft
Plnlon nut .
Nut of pinion
beoring coP
Nut of releose sleeve
bol
Nut of front cover bolt
Nut of speedometer shoft clip bolt
Nut of speedometer drive beoring
bolt
Nut of reverse-geor pin
bolt
Bolt of reverse-geor pin
Bolt of shifter forks
Bolt of cop of lock-boll springs
Silentblock bolt
Bolt of differentiol cose
Bolt of crown geor
Droin ond inspection hole plugs
Switch or bolt of reversing lomps .
REAR AXLE
Connection M8
M 22x1.5
M 24x1.5
M8
M6 M8
M 22x1.5
M 14x1
Dimensions 40-50
14-17
6-8 19-25
7-9
7-9 17 -20
7 -9
14-17
7 -9
30-40 22-25
35-45
20-30
70-80
M6
M6
M8
M8
M6
M6
M10
M8
M 10x1 30-35
7 -9
Tightening torque Nmr)
Rood wheels nuts .
Nut of oxle-shoft boll
Nut of oxle shoft
.ioin;
boit M 12x1.5
M8 M 18x1.5
M8
M10
Dimension 60-70
20-25
17O *)
a
40-50
Bolt of broke
bocking plote
Bolt of wheel cylinder
FRONT AXIE
Connection Tightening
torque Nml)
Nut fostening lower wishbone fulcrum
brocket to bodywork
Nut of lower wishbone fulcrum
brocket
(next to rubber bush -
inner)
Ditto -
outer lock nut .
Nut of upper wishbone fulcrum
brocket
(next to rubber bush -
inner)
Ditto -
outer lock nut .
Nut of upper wishbone pin (connection
with steering
knuckle pivot)
Nut of lower wishbone pin (connection
with steering
knuckle socket)
Nut of wheel
hub beoring .
Nut of steering knuckle pivot
.
Nut of lower
wishbone brocket bolt .
Nut of bolt fostening shock obsorber to its onchor brocket
Nut fostening shock
obsorber to
bodywork
Wheel nuts
Bolt fostening
front oxle to bodywork .
Bolt of
onti-roll bor brocket see
Chopter 6.5, points
24 ond 25
see Chopter 6.5, point
21
M
,M M
M
M
M 12x1.5
12x1.5
12x1.5
12x1.5
12x1.5
12x1.5 6s-70
45-60
70-90
45-60
70-90
70*)
70 *l
40-50 50-55 12-14
60-70
40-45
12-16
M
12x1.5
M10
M 12x1.5
M10
M 12x1.5
M10
M7
*) Further tightening os
required for olignlng holes
for the cotter pin.
22

metre), ond the
relotion of 1
kpm :9.806
Nm is'
opplicoble. When opplied to tightening
torques
of bolts ond nuts, use the relotion
10 Nm :
: 1 kpm.
d) The unit of power (output) tW'
(wott)
reploces the former "h.p."
(horsepower) ond
the relotion
of t h. p.:
735.499 W is opplicoble.
For procticol purposes,
o multiple of kW (kilo-
wott :
1,000 wotts) is used, i. e., t h. p. :
:0.736 kW.
e) The
unit of pressure "Po"
(poscol) or, in
proctice, MPo (megoposcol :
1,000,000 poscols)
or kPo (kiloposcol :
1,000 poscols)
reploces the
former "bor"
ond "kglcmz",
ond the following
relation is opplicoble: 1 MPo: 10 bors :1O.2
kg/cm2 (kp/cm2).
For current meosuring
of tyre
pressure etc., use the relotion: 100 kPo :
1 bor:
:1kglcm2 (kp/cm,) :1
otm.
1.10 GENERAL INSTRUCTIONS
With the exception of o few
speciol pro-
cedures or ossembly techniques
mentioned in
the respective section of
this monuol,
every
removol ond refitting (disossembly
ond re-
ossembly) should be governed
by the following
generol principles:
o) Use suitoble tools ond especiolly tubulor
box sponners which couse the leost domoge
to nuts ond bolt heods.
b) During disossembly note corefully how
the ports
hove been ossembled. This knowledge
is involuoble for correct reossembly.
c) Cleon ports
in trichloroethylene or tech-
nicol petrol.
They do not contoin substonces
(esoeciolly leod) which horm
the skin os motor
petrol does. Current bronds of seoling com-
pounds con be removed with denoturoted
ol-
cohol or scroped off. For o speciol
seoling
compound see the note ot the end of this
chopter.
Avoid contominotion of self-lubricoting
metol
beorings with ony degreosing
ogent os this
would unfovourobly offect their self-lubricoting
properties.
Cleon ports
of the broke ond clutch hydroulic
system with olcohor.
d) Lubricote
oll ports
moving on or in
eoch
other before their ossembly. Operoting lubri-
conts do not spreod eosily on dry surfoces,
the
ports ore not properly
lubricoted, ond friction
oreos ore opt to get
domoged. Coot the os-
sembled ports with the lubricont which is used
to lubricote them in operotion. When lubricoted
with oil, dip
the ports
in motor oil, the f luidity of which mokes
it
especiolly suitoble for
this
purpose. Use greoses
ond hydroulic f luid bronds
specified in the Toble
of Recommended Lubri-
conts.
e) Use new cotter pins
ond metol lock
woshers if you
ore not convinced of the perfect
condition of the old ones which could breok
ond leove the joints
unsecured. Moreover, there
is o risk
of the broken ports
domoging other
functionol ports.
f) Cleon new ontifriction beorings (boll,
rol-
ler, ond topered roller beorings) of preserving
greose using kerosene.
Preserving greose is not
suitoble for lubricotion ond it mixes bodly with
I ubriconts.
g) Some of the joints
hove to be tightened
with o moximum occurocy to the specified
tor-
ques listed in the previous
chopter.
h ) 'Ihe
permissible rototion unbolonce is spe-
cified for some of
the rototing ports,
usuolly in
gcm (gromcentimetres). A well boloqced port
con be stopped in
ony position
if it is
instolled
so thot no rototion resistonce
octs on it. With
the exception of dynomic boloncing, the ports
ore usuolly tested on on ouxiliory shoft ploced
on the
edges. The
unbolonced port
moves from
the deflected position
with its heoviest (i.
e.
unbolonced) port
downword. The
volue of un-
bolonce con be determined
when fostening
o weight corresponding to the permissible
un-
bolonce to the opposite side
of the unbolonced
port. lf the port
does not move when deflected
or if it moves with this weight downword; the
unbolonce is within the recommended limits.
The weight of the testing weight sholl be
de-
termined by dividing the volue of the permis-
sible unbolonce by the distonce of the weight
from the rototion
centre of the port.
i) Even slightly domoged seols ond pockings
must be reploced with new ones
Note: In the foctory,
the speciol seoling
compound
of the "Velvonton
C" brond is used for seoling
the engine reor
cover on the cylinder block, the
moting surfoces of the georbox housing holves,
ond the guide
of the clutch releose beoring.
This seoling compound is mode
on the bose
of o polyurethone
plostic ond it
corresponds to
"Hykemor", "Reineplost", "Curil
K" ond similor
compounds. lt con be removed from the ports
by scroping ond woshing with ocetone, butyl-
ocetone or chlorinoted solvents, for exomple
chloroform (trichloromethone)
ond corbon tetro-
ch loride.
24

5. Use
the MP 1'105 puller
for removing
cylinder liners from the
block. Turn the centre
bolts of the
iig to expond
the
iig iows in the
cylinder liner (ot
the top flonge of the liner)
ond pull
out the liner by turning the vwench.
6. Before removing the comshoft, lift owoy
the volve toppets. lf o
removol of the cylinder
heod is not considered, releose
the boll pins
of
the rocker orms, lift cwoy the push
rods, remove
the si'de cover of the push
rods, ond withdrow
the volve toppets.
2.5 BRAKE TEST
AND ENGINE
LUBRICATION SYSTEM DIAGRAM
Broke Tcst In view of
the very specific chorocter of
the test, especiolly with
regord to the speciol
testing eguipment,we do not intend to describe
the test procedure, restricting ourselves to
men'
tioning only the moin volues which the test is
supposed to verify. Volues indicoted in the
diogroms ore oppli'
coble to o new engine or on engine ofter o top
overhoul, which hos been
correctly run'in
by
running for o period
of obout 50 hours (2,500
km
trovelled). lf the engine is tested under other
conditions, the meosured volues must opprooch
the diogrom volues conformobly with the mech-
onicol condition of the engine.
ln diogroms, peok
performonce
volues ore
indicoted os meosured in complionce with the
CSw (Czechoslovok
Stote Standords) ond DIN
,CsNr
kwrotN'
1{J
I
20
r5t0 (Deutsche
Ingenieur Normen), i.e. with
oll oc'
cessoires reducing the gross engine
horsepower
(woter pump,
olternotor, oir
cleoner, exhoust
silencer). The
effective horsepower con
vory
with respect to the diogrom volues
within
o toleronce limit of
minus 100/s.
Every engine ofter
o top overhoul or reploce'
ment of individuol ports
of the cronk mech'
onism hos to be run'in exoctly like o
new
engine. Do
not forget to
drow your
customer's
ottention to this foct!
'",ffi15
NM
300 t000 som
t/n{a
5000 l/rnrn csilr
kwuril'
50
i
ilii Fig.2.5l2
-
Power Output ond Fuel Consumption
Diogrom -
Skodo 120 L engine
1- 3 see Fig.2.5l1
5000 t/mrn
Fig.2.511- Power Output ond
Fuel Consttmption
Diogrom -
Skodo 150
S
engine
1 -
power output, 2 -
torque, 3 -
specif ic fuel
consumPtion
k/SAE: h. p.
(SAE) 1/min :
r.P.m. Fig.2.513
-
Power Output ond Fuel Cons
Diogrom -
Skodo 120
LS engine
I
38 1- 3 see
Fig.2.5l1

6.
Complete the pump
ossembly by fitting
the
Stouffer lubricotor filled with
the recommended
greose.
2.15 ROCKER SHAFT AND ROCKERS
Assembly (on
Skodo 105 engine)
1. Instoll the lock ring, ploin
wosher, ond
spring wosher on the ro6ker shoft
with both
ends plugged.
Smeor the shoft with oil, fit the
rocker (with
its orm with the thrust foce de-
flected toword the next ossembled ports),
the
shim, the rocker support, ond the other
orm
def lected toword the support, i. e. the complete
rocker unit of cylinder
No. 1.
2. Then slip the spring,
the rocker, the sup-
port, the shim,
ond the next rocker, i.e.
the
complete rocker unit of cylinder
No.2, on the
shoft.
3. Threod on the spring ond, using the mirror
orrongement of the ossembled
rocker units,
instoll the rocker
units of the remoining
two
cylinders. Use o lock ring supplemented
with
o ploin
ond o spring wosher
to lock the os-
sembled ports
in position.
The rocker support of the cylinder No.4 must
be provided
with on oil hole
to provide
for the
supply of oil to the rocker shoft.
4. Compress
the springs
by holding down the
rocker orms ond lubricote
oll loterol contoct
surfoces with oil.
Assembly (on Skodo 120 L
ond 120 LS engines)
The rocker shoft is provided
with two od-
ditionol rocker supports fitted from
the outside
of the rocker units (the
shoft is longer), re-
plocing woshers obutting
on the lock rings.
For
the rest, the ossembly is identiccl
with the pro-
cedure described in porogrophs
1 to 4 obove.
NJote: Rocker orms
on the Skodo 120 LS en-
gine ore shorter (18.5
mm) thon those on the
Skodo -120
L ond Skodo 105 engines,
in order
to obtoin o higher rotio.
Disossembly
Remove the lock ring from the shoft
end ond
strike off the
entire volve nocker geor
from
the
shoft.
2.16 CYLINDER HEAD, VALVES
AND
SPRINGS
The cylinder heod is o costing of speciol grey
cost iron. The volve seots ond guides
ore cost
ond mochined directlv in tlre heod. The volves ore of different
diometers, the intoke volves
being lorger. Outer (exhoust)
ports
ore single,
oll remoinlng ore doubled, i.e. bifurcoted
ond
bronching to two volves in odioining
cylinders.
The centre exhoust port
bronches to the cyl.
inders No.2 ond 3, the neighbouring
intoke port
to the cylinders No. 1 ond 2, ond No. 3 ond 4.
The cylinder heod con be hondled
in the cor os
o unit. Of the individuol
iobs, only
the reploce-
ment of volve springs,
cotters, ond cylinder
heod bolts con be corried out with the engine
in. position in the cor. For oll the remoining
iobs, the
cylinder heod hos to be removed
from
the cor.
To remove
the volve springs,
screw out
the
sporking plugs ond, using o tommy
bor with
o curved end (steel
bor of obout 5 mm dio-
meter), broce
the volve to prevent
it from
sliding down into the combustion
chomber.
To Remove
Cylinder Heod from Engine
1. Let
the engine cool down before removing
the cylinder heod to preclude
worping of its
beoring surfoce.
2. Droin
the coolont into o cleon vessel (see
Chopter 15.13), detoch oll ports
connecting the
cylinder heod to the vehicle,
ond remove
oll
ports which ore likely
to obstruct the removol.
3. Remove the oir cleoner,
lift owoy
the
cylinder heod cover, ond remove
the nuts ond
bolts holding down
the cylinder heod (on
en-
gines of Skodo 120 L
ond 120 LS cors, two
bolts olso hold down
the end rocker
shoft sup-
ports) reversing the order of the numbers
in-
dicoted in Fig. 2.1611.
By pulling
the exhoust
monifold, disengoge the
cylinder heod ond lift
it owoy.
To Refit Cylinder
Heod on Engine
. 1.
Locote the cylinder heod gosket
on o per-
fectly cleon surfoce of the cylinder
block (cleon
Fi1.2.1611- Tightening Diogrom of Cylinder
Heod Bolts ond Nuts
For tightening torques see Chopter
1.8 the
cylinc
the oilwo,
structed c
Releose
once odjur
heod. lf nr
the rocker
2. Swin<
down the
porogroph
opply the
liminory o
the sequ€
(Fig. 2.16/
shoft suppr
3. Adjus
ter 2.13,
re
cleoner, rer
tighten oll
Cylinder Hr
Disossem
heod on o r
o support i
it does
not
o iob from
t
An exomple
1. Remove
the cosing
control, end
geor ofter
supports.
Fig.2Je
For holding
c
bolt M 8 scrt
rocker-shoft st
1 -
MP 1-113
v,
2 -
MP 1-114
v
Itl
I
I
/\.
-
( 3 r--{ 4)
\-/
\II
l
/
,/
t___v'
?,3
"'@-:lO
54

r
t
i
5. Prc
scri bed
rods onc
4th spee
fork rod,
irr the b
6. lnsl
guide bu
cover inr heods. S
tob wos
edges of
F it thr
stri ki ng
weoker s
ing forks 7. Tigl
the forks fork rod
the strik
function
Reverse-:
Fig
-1 - Rever
2-1st-o
3-3rd- o
4 -
Rever
8. Inst
press-f ittr
verse-spe
inside th
through t
Turn tl'
end foces
lock it in
hole. Tigl
Pinion Ar
9. Instc
ing ond,
r
_-_-- -
. i\:r,,,
\. 43
Fig. A.1l'l -
Power Pock
1 -
engine with mounting, 2 -
georbox/f inol
drive with
mounting, 3 -
reor oxle (holf-oxles),
4 -
rodius orms
retighten it using the recommended torque
(Chopter 1.8) ond screw down the clinch nut.
lf necessory, top up engine oil, f ill the cooling
system witlr on qntifreeze,
bleed the broke sys-
tem, ond
odiust the hond broke.
For the fosten-
ing of broke hoses (routing)
see Chopter 9.7.
4.2 ASSEMBLING
GEARBOX
Generolly, the reossembly
p'rocedure
depends
on the extent, to wlrich the unit hos been token
oport. For betterunderstonding,
we sholl des-
cribe the procedure
ond peculieorities
of reos-
sembly of o completely
disossembled unit.
Gear Chonge Mechonism
. 1.
Clomp the right-hond holf of the housing
(when viewed from the flonge securing
it to
the engine) in the MP 9-101 stond
com-
plemented with the MP 3-101 georbox
rock, ond
check the housing for completeness.
2. Instoll
circlips on the striking fork rods
of
the reverse
ond 1st ond 2nd speed. The ring
with the lower
nose is to be fitted
on the 1st--
ond 2nd-speed rods.
3. lnsert the reverse speed
striking fork rod
into the housing
so thot the inserted
end pro-
trudes slightly from its guide,
slip on it the
striking fork with the longer
side of its heod
first,- ond push
the striking fork rod through
the fork
ond the end of the guide
os for os=it
will go. 4. Fit tlre
MP 3-109 jig
into the free holes for
striking fork rods (both pins
of the
iig), ond
proceeding through the hole in its side ond
using o stick or o length of wire, push
the lock
pin into the housing
os for os it will go.
Proceed
in the some monner for
inserting the next pin
(use one pirr
of the
iig). Shift
it
iust so thot
the centre lrole remoins free for inserting
the
striking rod.
Puslr the lock pin
into the end
guide of the strikirrg
fork rods olso os for os it
will go. The
iig is not required
for
the instol-
lqtion of this pin.
Fig.4.2l1- Clomping Georbox Housing in Stond
Using MP 3-101 Rock
Fig.4.212 -
Locking Striking Fork Rods in
Position bv Meons of Lock
Pins ond Bolls
78 Fig.4.2l3
-
Instolling Lock Pins Using
MP 3-109 Jig

5.:
pr
stl
bc
5-t
bo
thr
u*,
on
dit
on arI
ioi
sPl
SW
I
gor
:
wo
bol
cyl
del
\
mo
th€ hot
WO
F
clo
POS +:
nec
wol
reo
toe
wit
T
o)
b)
Alil 1.
con
sloc
seo'
int
Fig.5.2l5
-
Pressing Boll Beoring
on Shoft
Using MP 5-112 Jig ond
lts Liner (smoller)
Fig.5.216 -
Connection of
Holf-oxles
with Rodius Arms
lorger ond one smoller, ond the forked plote),
screw down the
iig on the threod
of the shoft,
ond use
nuts to ottoch it
to the holf-oxle socketf
longe. The
iig of
the lotest design permits
its
simple fostening by engogement with
the holf-
oxle flonge (fit
the
iig ond
rotote
it to lock it
in position).
Instoll the lorger liner between the boll
beor-
irrg ond the
iig heod, ond
press
the boll
beorirrg
on the shoft by turning the iig wrench.
3. Reploce the lorger liner with the smoller
one (rest it ogoinst the
iig bolt heod), ond turn
the wrench in the opposite direction to press
the beoring into the holf-oxle socket.
Fitting Broke Mechonism ond Wheel Hub
4. Instoll the broke bocking plote
complete
with the broke
mechonism on the holf-oxle
socket, slip on the "O"
seoling ring ond the
cop with the seoling ring (with
the tightening
f in focing toword the holf-oxle), ond fosten
oll
the porrts
with bolts, spring woshers, ond
nuts.
The seoling ring should be driven or pressed
into the cop so thot the tightening lip foces the
beoring ond
iust so thot there
remoins
o gop
of
1 to 2 mm between the pocking
ond the cop
f longe.
5. lnsert the key in
the shoftwith its bevelled
end into the runout of the keywoy, smeor
the
hub neck with oil so
thot it does not
drog in
the seoling ring, ond fit the hub with the broke
drum in position.
Moke sure thot the key did
not move further olong the shoft (its
lifted end
in the keywoy would couse the hub to burst)
ond tighten
lightly the nut. Since o high
torque
is required
for finol tightening of the nut, put
off the tightening ond locking of the nut till
ofter instollotion in the cor. Then
tighten the
nut with full torque (see
Chopter 1.8),
top on
the hub to relieve
the possive
stress of the
toper, retighten to the specified torque, ond
lock the nut with o cotter pin.
Fitting Rodius Arms
6. Instoll
the spocer into the rodius
orm, fit
the knurled
woshers (with
the knurling toword
the orm)
to either side of the ellipticol holes of
the rodius
orm, ond fosten them with bolts ond
nuts not
forgetting the spring woshers. Do not
tighten the connection fully. Threod
the bolts
through the bolt holes so thot their nuts foce
into the cor ofter fitting the rodius orm to the
holf-oxle.
Fit the rodius
arm on the protruding
holf-oxle
pin ond threod
the bolt through the hole
of the
secrt. Slip
spocing tubes on the bolt ond pin
together with sheet shims with rubber liners
ond fosten
lightly (without tightening)
the
rodius orm to the holf-oxle using nuts
ond lock
woshers. Tighten
fully the connection
ofter fit-
ting the ossembly
in the cor when odiusting
the
reor wheel
olignment (geometry).
il
i
ii
I
I
I
I
lr
il
H, DK
?EI
98

1
\
I
(
r
t
(
s I
I
(
S
lf
m
gr
lir
O1
sy
ro
po
th
th
th, tir
on
m€
tht
of
onl
I
by tr
Cl
A
6-
tl-
th
th
Fig.6.5/5
-
Pressing-in Beoring Cups Using
MP 6-130 Jig
Fig.6.5/5 -
Instolling Seoling Ring
Using
MP 6-131 Jig 23-
Fit the disk broke bock plote
on the
steering knuckle ond fosten it by bolting down
the broke brocket. Use spring woshers to lock
the bolts. Drive home the wheel hub
on the
steering knuckle with light tops ond use o tube
to top home the beoring cone.
24. Fit the greose-pocked
cone of the outer
beoring on the steering knuckie, locote
the
shim on the beoring, ond tighten the nut with
o torque of 1.5 kpnr (15
Nm) while rototing the
wheel hub.
25. Top
the wheel hub ond the broke disk
with o mollet ond rotote
the wheel hub to bed
in the beorings. Bock off the nut
through obout
-180o
ond retighten it with o torque of obout 5 Nm
(0.5 kpm) while rototing the hub. Then bock off
the nut to the neorest cotter pin
slot (ot
the
most through 30"), ond lock it in this position
by inserting the cotter pin.
26. Check whether the wheel hub rototes
freely br-rt without ony noticeoble
cleoronce in
the beorings, ond secure the nut with the cotter
pin.
Fittirrg Steering Knuckles ond Wheel Hub
into Wishbones
27. Hoving thus ossembled the wheel, instoll
ii into the lower
wishbone, fit
o shim between
tl-re wishbone reor eye ond the resilient bush in
the king pin socket,
threod in the eccentric pin,
cind screw down the nut without tightening it.
28. Press
the wheel ogoinst tlre
upper wish-
borre ond connect it with it
by topping home
the wishbone pin
from the reor side
of the
oxle,
i. e., from the side of the shorter port
of the
king pin
socket. Slip the MP 6-108 pilot
pin
on
the wishbone pin
threod to focilitote threoding
of the pin
through the hole in the wishbone.
Tighten slightly the connection with the costel-
loted nut.
DK ? 2r+
Fig. 6.517 -
MP 6--108 Pilot Pin for
Upper
Wishbone Pin lnstollotion
112