1980 SKODA 120 LS belt

2.2-2.3
threods. Fill the etrgine with oil ond the cooling
systenr with on ontifreeze, ond
bleed them.
2.3 REASSEMBLING THE ENGINE
The reossembly procedure depends
on the
extent to which the engine hos been
dis-
rnontled. For better understonditrg, o
reossembly
of o conrpletely disnrontled
engine is described
in the following
porogrophs.
lnspection of
Cylinder Block
1. Clomp the thoroughly cleoned
cylinder
block into the MP 9-101 stond with the engine
corrier type MP 1-101 ond check it for complete-
ness -
see Chopter 2.6. Fit the
block with its
lugs on the engine corrier pins
ond use the side
bolt for ltolding it down.
DK 1188
Fig.2311- Cylinder Block Fostened on the
Assenrbly Stond by lVleons of the MP 1-10-l
Corrier
2. Rernove the pressure
relief volve, moke
sure thot the boll contoct {oces ore cleon,
ond
refit the cleoned volve. Forr
f itting o new volve
see Chopter 2.6.
3. Remove the cronkshoft beoring
covers ond
tlre i;ylinder block reor cover.
To Refit the Cronkshoft
4. Force the beoring shell lrolves with the
fingers into the cronkshoft beoring bores so thot
the shell lip snops home into the slot (cut-out)
in the block ond so thot the shells do not pro'
trude over the beoring surfoces for the beoring
covers, ond lubricote them with engine oil. Be
r;ure to fit shells motching the cronkshoft
i":urnols -
see Chopter 2.7.
5. Slip the oiled guide
ring on the cronkshcft
"vith oil grooves
pointing
toword the cronkshoft
'.veb ond {it the cronkshoft with the pressed-on
boll beoring (see
Chopter 2.7)
into the shell. 6.
Inscrt the
beoring shell
holf ir-rto
the cover
of the beoring No.-l
os described in
porogroph
4,
ond fit the cover with the
recess for the guide
ring turned outword. Proceeding from
the front
of lhe block, slip
on the next guide ring with
the oil grooves pointing
owoy from the block so
thot itJ
lip engoges ogoin into
the slot in the
cover. Coot the ring
with oil ond slip on the
thrust ring. Fit the MP -1'112
thrust collor on the
cronkshofi ond
tighten the
beoring slightly
using the belt
PrrlleY bolt.
7. Instoll the next
two beorirrg covers
corl'l'
plete with beoring shells
ond lightly
tighten l.he
cover nuts.
Press the cork
seol
into the
reo'r
cover moking
sure thot it
f its the groove
snugly
ond slightly bverlops the lower
seoting surfoce'
Before titting the cork seols,
compress them
for
o while in o vice to distort them. Insert the
distorted seols in the grooves
or gops between
the cover qnd
the cylinder block
where they
will expond onci provide
for perfect seoling.
lnsert tob woshers under
the nuts of the
beoring covers
ond while tightening the rruts
check their correct position so os
to enoble
o subsequent correct locking
of the nuts.
Fig.2.312 -
Meosuring Cronkshoft Ploy
1 -
Thrust collor, type
MP 1 112
2 -
Diol indicotor in o
speciolly mode yoke
8. Rotote the cronkshoft severol times ond
using o mollet top the covers ond both shoft
ends to ensure o correct bedding
of the covers
ond cronkshoft guide rings.
9. Tighten the belt pulley nut
to clomp the
thrust ring, ond
rotote ond force
off
the cronk-
shoft to
check its ploy. The
cronkshoft must
be
free to rotote but
without ony
noticeoble ploy.
lf there is o noticeoble ploy, recheck
its volue
ond odiust it by replocing the guide ring with
o new one. The
moximum ploy
should not ex-
ceed 0.10 mm, the recommended minimum ploy
being 0.04 mm. 10.
F
speciol
end onr Drive
suchr o
be turnr
cover. I
ever, tf
the cyl
speciol note in
11. Ti
the tigh
in the
covers. hoving
does no
must ro
Then lo,
woshers
ond nut
To Refil
12. R
greose i
it with i
o flywhr
engine,
with rec
under tt
Chopter
bending
shoft og
powl ins
For flyw
Fig.2.3l3
Using thr
Screw
holes, for
con be ur
further o1
the hondr
30

primory
feed to the distributor coincides with
the connecting line of the
distributor centre
line ond the first cylinder
heod
bolt os
per
Fig.2.3l10. Secure the distributor in this pos-
ition by lightly tightenning the tie-bolt ond
remove the timing geor
cover from the cylinder
block. The used type of distributor is described
in Chopter 13.5.
Fig.2.3l10 -
Position of Distributor on Engine
-l - screw of primory power
feed
2 -
cylinder heod bolt
3 -
index line rnorking the position
of the
distributor ornr when cvlinder No. 1 f ires
24. Coot with oil the moting
surfoces of the
timing geor cover ond the cylinder
block, locote
the cover gosket
on the block,
oil the timing
choin ond the comshott worm geor.
Remove the
f lywheel powl
ond rotote the
cronkshoft through
360o so
os to bring tlre pistons
of the cylinders
No. 1 ond 4 to their TDC position
ogoin. This
position corresponds opproximotely
to the volve
geor position
when the cylinder No. 1 f ires (the
tips of the coms of
cylinder No. 1 ore turned
downword, owoy from
the engine). Lock the
cronkshoft in position by refitting ond tight-
ening the flywheel powl.
25. Turn
the distributor orm in the direction
of the
screw (1) in occordonce with Fig. 2.3110,
hold it down with the
finger in this position,
ond ref it the timing geor
cover on the cylinder
block. By sliding the worm geor
of the distribu-
tor drive into the comshoft worm geor,
the orm
is turned to coincide with the timing
mork for
cylinder No. 1
on the distributor housing. lf
there is no coincidence of the orm ond timing
mork, od just
the position
of the orm by
slightly
rototing the distributor.
lf the
misolignment of the distributor
ornr
ond the timinq
mork of the
cvlinder
No'1 is so greot
thot it connot be corrected
by rototing
the distributor, remove
the timing geor
cover,
rotote the distributor slightly ond repeot
the
entire procedure
of refitting the timing geor
cover. 26. Smeor the protruding
end of the cronk-
shoft ond the outer shoft end (stem)
of the
belt
pulley with oil, f
it the belt pulley,
the nespective
wosher, ond tighten the bolt. Bolt the
PumP
suction stroiner tothe cronkshoft centre beoring
ond use o spring
wosher under the bolt heod.
27. Bolt down the timing geor
cover using
spring woshers ond
cheese-heod bolts
(exclus-
ively) cnd f inolly fosten the timing geor
cover
in such o position
thot the contoct breoker
points open before the crronkshoft with
the con-
necting rod ond piston
hos ottoined the top
deod centre (TDC)
position (see
the lgnition
Timing Toble in Chopter 15.3).
For checking the ignition odvonce, on electric
power supply is required with o bulb connected
in o circuit with the distributor. this
circuit
being interrupted by the oction of the contoct
breoker. An odopted conventionol torch with o
metol
iocket con be
used with odvontoge for this
purpose. Remove the flywheel powl ond
set the re-
quired ignition odvonce by turning the cronk-
shoft with o screw'driver inserted into
the geor
ring ond propped ogoinst the cylinder block
f longe. Rotote the shof t onticlockwise o bit
more thon necessory ond
bock it off so os to
odiust the bocklosh of the timing geors
ond the
distributor drive geors.
oK 6ls
Fi9.2.3111- Lomp for Checking the Opening
of Contoct Breoker Points
-1 - torch complete with dry cell ond bulb
2 -
leod with olligotor clomp
3 -
botterv cell
4 -
torch coo
5 -
contoct spring
6 -
insuloting plote
7 -
electricol-contoct connection of the leod
with the
drv cell Con
using
torch.
the br
slowly
indico
A corr
is not
timing 28.L
beorin
Then f
while
oil sun
the thr
the tyl
see Cl.
shri n ks
of the
woter
move i
ively.
To Fit
Toppetr
25. r
remove
positior
sure thr
cylinder
cylinder nuts. F<
first bo
woteir p
oir clec
finol ti1
2.16.
Ploin
heod bo
which t
woshers
no wosl
heod bo
cy I i nder
the outs
hove to
of the rc
Tighte
broce or,
30. Sc
thermom
into the
cosing o
ofter ho
Use spri
thermost
cooted g
with the
with the
The th
should br
34

ilil
ll
I
Z,l
spring woshers under the pump
fostening nuts.
36. lnstoll the oil filter -
see Oil Filter in
Chopter 15.3.
37. Bolt the brocket ond the reloy lever
of the
occelerotor linkoge to the intoke monifold, Use
spring woshers to lock the bolts in position.
38. Locote the corburettor gosket, sheet
guord, onother gosket,
the insuloting wosher,
ond o third gosket (oltogether
three goskets
of
the some type) on the intoke monifold inlet
socket, instoll the corburettor,
ond tighten
it
down with nuts.
On 105 ond 120 l- engines, the sheet guord
must be fitted to the intoke monifold inlet
socket with o throttling spider, while 120 LS
engines must hove the possoge
unobstructed.
39. Smeor the boll pins
of the linkoge
ond
corburettor lever with greose
contoining molyb-
denum disulphide
ond mount on them the oc-
celerotor link (tie-rod).
Hold the link in pliers
ond slip securing clips over the heods.
Hook o spring on the shonk of the reloy
link-
oge boll pin
ond on the rib of the forehousing
on the corburettor.
40. Screw down the vocuum
control pipe
on
the corburettor (using
double-sided seoling
rings) ond slip on the rubber
hose connecting
the pipe
with the distributor vocuum control
unit. Secure the pipe
by bending the clip under
the nut of the intoke ond exhoust monifold.
To Refit Alternotor
41. Attoch the olternotor
brocket to the side
of the cylinder block while putting
ploin
woshers under
the nuts. Mount the olternotor
holder together with the engine mounting lug
on the bolt of the timing geor
cover ond the
front lug of the cylinder block.
Use self-locking
nuts for the bolts f ostening the olternotor
holder. Lock
the lower bolt of the lug by meons
of o spring wosher
ond nut. Using onother bolt,
bolt together the lug ond the brocket. lnsert
the tie-bolt from
the side
of the lug, slip on
o ploin
wosher ond tighten the nut. Fit the
short-circuit strip on the bolt ond lock it in
o position
porollel
with the olternotor brocket
by screwing
down the respective nut with
o ploin
wosher.
42. Put the olternotor into the holder,
ttrreod
in the bolt, ond screw down the nut with o ploin
wosher without tightening. Without tightening
the self-locking
nut, bolt the strut into the
brocket on the cylinder heod. Swing the olter-
notor toword the engine, fit
the V-belt ond,
while tensioning it, connect the olternotor with
the strut using o bolt, spring wosher ond nut.
At the some time, tighten the nut of the bolt
holding down the olternotor
in the
holder ond
the nut of the bolt connecting the strut with
the holder. For the belt slock odiustment see
Chopter 15.3. 43.
Fosten the second
engine mounting lug
using nuts with spring woshers.
To Fit Cylinder Heod, Air
Cleoner,
ond Sporking Plugs
44. Fit the cylinder heod
with cemented.on
gosket on the cylinder block ofter hoving slip-
ped o seoling ring ond o wosher on eoch bolt,
the some os in the cose of the push-rod
cover.
In oddition, fit the fuel pipe
holder on the reor
bolt ond hold it down by slightly tightening the
nut.
45. Fit the oir cleoner in position
ond fosten
it to the corburettor with o bolt using o seoling
ring ond wosher. Put o spring wosher
under the
nut on the brocket
ond screw down the nut on
the bolt of the cover without ony wosher.
46. Threod the fuel hose through its holder
on the cylinder heod ond use clips to fosten it
to the corburettor ond pump.
Adiust the most
suitoble position of the hose by rototing
the
holder ond then tighten the nut.
47. Attoch hoses connecting the oir cleoner
with the corburettor ond the oil filler neck.
When preporing
the cc for driving in winter,
instoll the winter
oir-intoke tube (hose) -
for
detoiled instructions see Chopter 15.3 "Air
Cleoner -
Winter Operotion".
48. Screw in the sporking plugs
with seoling
iings ond fit the ignition cobles. For the re-
commended types of sporking plugs
see Chopter
13.7.
The outlet on the distributor cop morked with
o notch is intended for
the coble
to cylinder
No. 1. The
remoining outlets ore.to be counted
clockwise ond in direct
order from 1
to 4 ond
the cobles will be connected to sporking plugs
in the order of numbers cost on the cylinder
heod beside the recesses for sporking plugs.
Plug Screws ond Lubricotion
System
Accessories
49. Plug the oil sump with the conicol screw
plug with its
seoling ring. In the cose of on
engine without the oil cooler, plug
the oilwoy
on the timing geor
cover with o screw plug
with o seoling
ring, ond the oilwoy ot the reor
end of the cylinder block with o pressure
switch. lf the socket for screwing down the
pressure switch is missing, instoll o new socket
together with its respective seoling ring.
lf on oil cooler is provided,
hoses ond o press-
ure switch should be
connected to the oilwoys
occording to Chopter 11.9.
Put the oil dipstick
with the f itted rubber ring
in its ploce.
For the type of the dipstick see
Chopter 2.17.
50. Using spring
woshers with the bolts,
screw down the flywheel
guorcl
ofter removing
36

Alternoting
cylinder No. 1
cylinder No.3
cylinder No.4
cylinder No. 2 Adjust cleoronce
on
cylinder No.4
cylinder No.2
cylinder No. 1
cylinder No.3
Fi1.2.1312
-
Volve Cleoronce Adjustment link from the choin
front side ond fit the clip
from the reor with its open end pointing in
the
direction opposite to the choin movement.
Before storting work on the volve geor,
re-
move the oil sump (engine
bottom cover to
which the timing geor
cover is bolted, the suc-
tion stroiner being ottoched to the cronkshoft
centre beoring cover) ond lock
the cronkshoft
in position
in the oxiol direction by depressing
the clutch pedol,
if removol of the entire engine
is not intended for onother purpose.
For speciol
points of the removol refer to
Chopter 2.4.
2.14 WATER PUMP
Disossembly 1. Unlock the wosher of the belt pulley
nut,
remove the nut ond pull
off the belt pulley
using
the MP 1-120 puller (o
fixturre for
Skodo MB 1000
cors) or o universol puller,
for the bolts of which
it is necessory to
cut threods M 8 in the belt
pulley holes.
By pulling
off the belt pulley,
occess will be
goined to the nuts fostening the pump
to the
engine. The some procedure
holds good
when
dismontling the pump
ofter it hos been removed
from the engine.
2. Withdrow the keyfrom
the shoft ond, using
the drift MP 1-121, drive
or press
out the shoft.
Then lift owoy the
housing plote
from the
seoting foce of the pump.
3. Remove the circlip locking the outer boll
beoring in position.
Proceeding from the reor
side of the pump
housing, drive out the boll
beorings with their spocer tube, ond remove
the
rubber seoling rring
from the housing.
Reossembly 1. Smeor the rubber seoling ring with greose
ond insert it into the pump
housing.
Use the
MP 1-123 drift to drive home the inner boll
beoring (without
sheet guord) pocked
with
greose. When opplying the drift,
fit its guide
ring into the bore for the
oute,r boll beoring.
2. Fit the gosket
on the pump
seoting foce
ond ploce
the pump plote
with its cemented-on
gosket (focing outwords from the pump)
over it.
Fosten the plote
to the pump provisionolly
with
one bolt to prevent
the gosket
from being dom-
oged during the following ossembly
iobs.
Insert the rubber seol,
wosher, ond conicol
spring into the speciol (bokelite)
seoling ring
of the pocking glond.
Instoll the spring
with
its nose
into the hole in
the bokelite pocking.
Slip the ossembled pocking glond
on the shoft
with the spring toword the shoft geor,
ond drive
the shoft home into the pump
beoring, while
supporting the beoring with the MP 1-123 drift. Fig.2
4. Fit t
shoft ond
stolling th
in positior
it with gre
sheet guor
5. Top
t
lieve the r
@@@@
DK 1240
Fig.2.1313 -
Volve Arrongement in Cylinderr Heod
Block disks -
exhoust volves
White disks -
intoke volves
Timing Choin ond Timing
Geors
Modified chain and gears
fitted since October
1979 recognised by
squared gearteeth
and chain
with split rollers.
The timing choin hos no slock odiuster (ten-
sioner). A slock choin does not substontiolly
offect the volve geor
occurocy but its operotion
is noisy. Therefore
its correct length should
be
ensured either
o) by selecting o suitoble choin from o number
of choins ovoiloble -
try it on the timing
geors, o1r
b) by replocing the stondord comshoft geor
with on oversize geor
(with greoter
toler-
onces). The comshoft geors
ore groded
in
keeping with their progressive
size (tol-
eronces) into closses A, B ond C. With the
exception of
closs A, the closs morking
letters ore stomped next
to the punch
mork.
For trying, the choin con be disconnected
to ovoid removing ond refitting of the timing
geors. To recouple the choin, insert the coupling Fig.2.1t
52

L
i g)
Excitotion of the olternotor by o current
supply outside the cor is not permitted.
Agoin the semiconductors would suffer.
h) A blown chorging worning lomp must be
reploced immediotely with o new
one. Other-
wise correct excitotion of the olternotor is
not ensured. Use o new lomp of
the some
roting (or input), i.
e., 1.5
to 2 W.
i) Be sure thot there is
o perfect
electricol
connection on the connecting terminols ond
thot the olternotor
ond regulotor
ore properly
eorthed.
i) The
olternotor is oeroted, open. Therefore
toke core when woshing the cor thot woter
or cleoning ogents do not get
into it through
the venting holes.
Removing the Alternqtor
1. Disconnect the bottery.
2. Disconnect the olternotor leods. lt will be
helpful to remember the colour of one conductor
ond its connection for reinstollotion.
3. Remove oll ports
holding the olternotor on
the engine, ond lift owoy the olternotor.
Reinstolling the Alternotor
1. Cleon oll mounting surfoces.
For the olter-
notor mounting, see Chopter 2.3, por.42.
2. With the bottery
disconnected, insert the
conductors into the respective
connectors "M,,
ond "R"
(the conductors beor the some sym-
bols), ond fosten the remoining leod with o nut.
3. Reconnect the botterv. Alternotor
Disossembly -
Repoirs
1. Screw off the belt pulley
nut ond remove
the belt pulley
ond fon.
2. Lift the brushes with o hook proceeding
through the holes in the
commutotor end
shield
ond hold them in the lifted position
by wires
inserted into the shield through dio. 3 mm holes
under the terminols uM'
ond "Ru.
3. Mork the mutuol (relotive) position
of the
commutotor ond drive end shields ond seporote
the qlternotor
ofter hoving removed its clomping
bolts. The drive end shield remoins connected
with the stotor.
This disossembly will give
occess to the
brushes ond some
of the diodes. All other
iobs,
with the exception of the renewol of the beor-
ing, should be done by experts in speciolized
repcir shops -
see the note supplementing the
following porogrophs.
Alternotor Reossembly
1. Insert the circlip into the becring bore
in
the commutotor end shield.
2. Fit the drive end shield with beoring on
the rotor shoft.
3. Assemble the stotor with the rotor ond the
commutotor end shield. 4" Tighten the olternoior with clomping bolts
ond check the rotor for free rototion while
tightening the bolts.
5. Slip the spocer on to tlre shoft,
top the
key in position,
fit the fon ond belt pulley,
ond
tighten the entire ossembly using the nut with
spring wosher.
6. Pull out wires from the commutotor end
shield which hove been used to hold
brushes
in their lifted position.
Replocement of Beorings
The used beorings ore fullyclosed ond seoled,
ond they hove been filled in the foctory
with
lubricont to lost through their entire service life.
1. Pull the beoring off the rotor
using o suit-
oble puller.
When ref itting the beoring, press
it
on to beor on the shoft
collor-
2. Before removing the drive end shield
beor-
ing, f irst drill off the heods
of the flonge rivets
ond then drive the beoring out from
the outer
side of the drive end shield using o suitoble
mondrel (drift).
On reossembly,
close the beoring with the
flonge ond rivet the flonge to the shield.
Replocement of Diodes
The use of the removoble
diode block with
the individuol
corriers of the so-colled positive,
negotive, ond ouxiliory diodes, focilitotes con-
siderobly the replccement of ony defective
176
Fig.133la
-
Alternotor -
Sectionol View

l4.l
l-14.12
has two anchoring points.
The seat belts have
anchoring bolts
on the size 7/16-20 UNF-2A'
In f ront, the anchoring threads
are easily
accessible being provided
on the door posts
(remove only one of the pair
of pins
covering the
thread), on sills
below the posts,
and on
the sides
of the'floor tunnel
behind the front seats'
Anchoring points
for rear seat belts are shown
in the illustation. For the seat
belt of the person
sitting in the
middle, the threads are under the
seat cushions and rather removed from each other
(A3). For the seat belts of persons
occupying the
butside places
the threads are also under the
cushions, nearer to the centre (A2),
in the body
sides close to the cusions (82),
and in window
pillars (C2). These latter threads can be found by
touch in the point
of intersection of the plane
passing about 165 mm
above the
rear window
parcel tray and in parallel
with the door frame at a
distance of about 85 mm. To gain
access to
them,
it is necessary to cut through the trimming.
We must stress that for the fitting of points A2
and A3, the bolts should not protrude
beyond the Fig.M.11l2
-
Lower Anchoring Points
14-12 FACIA
l-he focio cctl be rentoved otter unsct-ewlllg
the nuts of its peripherol bolts ond
ofter lifting
owoy the instrument ponel -
see Chopter '13'15'
It is olso necessory to
remove the steering
wheel with the shroud of
the steering wheel
shoft (see
Chopters 7.7
ond
7.8), ond the heoter
control ponel
(see ChoPter 11.0).
The bolts holding down the focio
ore occess-
ible ofter removin! the
instrument ponel
ond
the heoter control ponel, ond
ofter swinging. out
the glove
box. To swing
out the glove
box,
open its lid ond loosen tlre screws of its
stops'
Fig. 14.1111 -
Upper Anchoring Point
captive not more
than 1lz mm or there is every
likelihood of damaging the
fuel tank.
The depth of the nut from the mounting face
is
15 mm.
Child seat fixing
Follow the seat belt manufacturers instructions
as to the spacing of the belt straps.
The straps can be mounted to the rear parcel
shelf if the mounting holes are drilled 30 mm from
the front engine bulkhead. The
sound deadening
trim in the engine compartment
will need to be
lowered to fit the spreading plate
and nut.
Be careful when drilling the shelf, not to
scratch the rear screen. Fig.
14.1211 -
Focio Mounting Points
14.13 WATER LEAKS
To determine the
source of
a water leak
proceed in a progressive
manner.
1. Determine area
water finally rests'
2. lf possible follow
water trace to
source'
3. lf hot, remove carpets and clutter'
4. Dry car inside
and out'
5. Us'e a sprinkler rather
than
a hose jet'
6. Start on the
underside of
the vehicle and
work up. Do not
do any adjustments or
sealing until after the
first test.
7. When"you have
finished adjustments and
sealing RE
TEST.
212

I-
.'t Fig.
15.3/3 -
Oil Filter
oil f ilter bowl
witlr f ilter
element
centre-boll oil pressure
switclr pressure
oir. When driving often
on dusty roods,
ihe cleoning intervols
should
be shortened by
holf. For oir cleoner mointenonce in tropicol
re'
gions refer to
ChoPter 16.2.
Air Cleoner -
winter oPerotion
Remove the rubber
cop from
the cover exten-
sion orm ond
use it to stop the mouth of
the
orm. Fit o guide extension into
the cleored hole
in the ornr ond
insert the
corrugoted poper hose
(included in the
cor equipment) into
the
ex-
iension ond
the holder on the
intoke ond
ex-
houst monifold.
Give the
hose the required shope by
bending
it slowly ond corefully. Above
oll, ploce
it into
the holcier so thot
there is
o suff icient distonce
(wide enough to
insert o
finger) between it
crnd the exhot-tst monifold.
Tightening of
cYlinder heod bolts
The cylinder heod
bolts should be tightened
in the running-in period before
the gosket gets
settled ond then
ofter every replocement of the
gosket, i.e., ofter
obout 1,000
kilometres' For
itre tightening procedure,
s9e
Chopter
-2'16'
Check'ilg of vilve
cleoronce ofter
every tighten'
ing of tlie
cylinder heod
is o
routine procedure
which must not be omitted.
Volve Cleoronce
For checking procedures
ond odiusting volues,
refer to ChoPter 2.13.
Alternotor V'belt
Tensioning
Loosen the
nuts of the bolts
in the olternotor
f longe (fostening
it to
the engine ond
the strut)
ond'of itre
bottJ holding down
the strut on
the
olternotor, ond
swing
oside (tip)
the olternotor'
Adiust the
belt so
thot it gives
woy 10- to
15 mm midwoy between the
belt pulleys
when
depressed lightly (ot
if o- weight of obout
2 kg were opplieal with
the
finger ot this point'
LoCk the
olternotor in
this position
by tighten-
ing properlY
oll the nuts.
Belt dimensions: 9x9.5x1,0O0 mm.
To Cleon the
Distributor
The contoct breoker points, the
cover, ond
the rotor orm
of the distributor must never
be
greosy or dirty. Scrope off
ony burns on the
distributor cover.
lf you hove
cleoned the
distributor with
oetrol, do
not ref it the cover till ofter
the petrol
hos comPletelY evoPoroted.
222
oll
the greose
into the beorings. Tighten
the
cop thoioughly so
thot it connot be worked
loose by vibrotion.
Air Cleoner -
cleoning ond
replocing of
filter
element
Unclosp the cover
fostening clips
and lift
owoy the lid. Depress the
cross broce in
the
1ock6t, rotote
it
slightly to disengoge it, ond
withdrow the filter
element. Wipe
cleon the
inside of the
iocket, cleon
the filter
element or
reploce it with o new
one, ond reclose the oir
cleoner proceeding
in reverse order.
Shoke ond
top the filtet element to
rid it of
clirt porticles, oncl
blow it off ond through with
Fiq.15314
-
Lubricotor of
Woter Pump Beorings