1969 FORD MUSTANG trans

04-03-07
Rear Axles — Integral Carrier Type

04-03-07

junction and install vent hose to vent

tube.

7.
Raise the axle housing and con-

nect the shock absorbers.
8. Connect the rear end of the drive

shaft to the axle U-joint flange, align-

ing the scribe marks made on the

drive shaft end yoke and the axle U-
joint flange (Fig. 14).

9. Fill the axle with the proper

grade and amount of lubricant.

10.
Road test the vehicle.

MAJOR REPAIR OPERATIONS

DISASSEMBLY

All service operations on the differ-

ential case assembly and the drive pin-

ion assembly can be performed with

the housing in the vehicle.

REMOVAL OF

DIFFERENTIAL

CASE AND DRIVE PINION

1.
Raise the vehicle and support it

on the underbody, so that the rear

axle drops down as far as the springs

and shock absorbers permit.

2.
Remove the cover from the car-

rier casting rear face, and drain the

lubricant.

3.
Perform the Inspection Before

Disassembly of Carrier in Part 4-1,

Section 3.

4.
Remove both rear wheels.

5.
Remove the brake drums.
6. Working through the hole pro-

vided in the axle shaft flange, remove

the nuts that attach the wheel bearing

retainers to the axle housing.

7.
Pull the axle shafts with the tool

shown in Fig. 2. Care must be exer-

cised to prevent damage to the oil

seals.
Install a nut on one of the brake

backing plate attaching bolts to hold

the plate to the axle housing after the

shaft has been removed. Remove both

seals with the tool shown in Fig. 8.

8. Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 14). Dis-

connect the drive shaft from the axle

U-joint flange. Be careful to avoid

dropping the loose universal joint

bearing cups. Hold the cups on the

spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when
they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission leak-

age.
Refer to the transmission group

for the appropriate tool.

9. Remove the differential bearing

adjusting nut locks (Fig. 15).

10.
Mark one differential bearing

cap and the case (Fig. 16) to help po-

sition the parts properly during as-

sembly.

11.
Remove the differential bearing

cap bolts and bearing caps. Hold the

differential case assembly in the hous-

ing after the caps are removed.

12.
Remove the differential case

and bearing cups (Fig. 17).

13.
Hold the drive pinion flange

and remove the pinion nut (Fig. 9).

14.
Remove the pinion flange (Fig.

10).

DIFFERENTIAL PINION GEAR

AND THRUST WASHER

COVER AND GASKET
DIFFERENTIAL SIDE GEAR

AND THRUST WASHER

SHAFT RETAINER DIFFERENTIAL

PINION SHAFT DIFFERENT|AL

DIFFERENTIAL CASE CASE COVER
BEARING ADJUSTING NUT

PINION AND RING GEAR

AXLE SHAFT
BEARING

DRIVE GEAR ATTACHING BOLT

ADJUSTING NUT LOCK

BEARING CAP

PINION LOCATING SHIMS

BEARING AND CUP

WHEEL BEARING RETAINER

GASKET
BEARING AND CUP

SEAL

AXLE SHAFT SEAL

BEARING PRELOAD SPACER/
AXLE HOUSING

FILLER PLUG

'WHEEL BEARING

WHEEL BEARING RETAINER

DEFLECTOR FLANGE

E1908A

FIG. 75—Disassembled Rear Axleprocarmanuals.com

04-04-01

Rear Axle — Ford Light-Duty (WER)
04-04-01

PART 4-4 Rear Ax/e-Ford Light-Duty (WER)

COMPONENT INDEX

AXLE HOUSING

Cleaning and Inspection

Removal and Installation

AXLE SHAFT

Cleaning and Inspection

Removal and Installation

DESCRIPTION

DIFFERENTIAL CASE

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

DIFFERENTIAL BEARINGS AND DRIVE

GEAR

Cleaning and Inspection

Removal and Installation

PINION AND RING GEAR

Cleaning and Inspection

Removal and Installation

PINION BEARING CUPS

Cleaning and Inspection

Removal and Installation
MODEL APPLICATION
AN
Models
Ford

01-09

04-04

01-10

04-06

04-01

01-10

04-07

04-06

01-10

04-08

01-10

04-08

01-10

04-08
Mercury
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Meteor
01-09

04-04

01-10

04-06

04-01

01-10

04-07

04-06

01-10

04-08

01-10

04-08

01-10

04-08
Cougar
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Fairlane
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Falcon
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Montego
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Mustang
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Lincoln-
Continental
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Thunderbird
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Continental-
Mark
III
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of tne column.

N/A indicates that the item is not applicable to the vehicle listed.

DESCRIPTION

A light-duty, integral-carrier, con-

ventional-type rear axle assembly (Fig.

1) is used in Ford and Meteor passen-

ger vehicles equipped with 240-IV and

302 2V engines and related transmis-

sions.
The axle (model WER) incor-

porates the following features:

The hypoid gear set consists of an

8.50 inch diameter ring gear and an

overhung drive pinion which is sup-

ported by two opposed tapered roller

bearings. A drive pinion pilot bearing

is not used in this axle.

The differential carrier is the non-

removable type, with a stamped bolt-

on cover. The filler hole is tapped in
the front portion of the carrier casting

and uses a
1/2-14
tapered pipe plug

with a 3/8 inch square female drive. A

bumper pad is machined on the pinion

nose portion of the carrier. The rub-

ber bumper is mounted on the vehicle

underbody.

The differential case is a one-piece

design, with openings allowing assem-

bly of the internal components and lu-

bricant flow. The differential pinion

shaft is retained with a threaded bolt

(lock) assembled to the case.

The axle housing assembly consists

of tube assemblies pressed and welded

into the differential casting. The brake
backing plate retainer is welded in-

board of the outer edges of the tubes,

and allows assembly of the backing

plate, independent of the axle shafts.

The roller-type wheel bearings have

no inner race, and contact the bearing

journals of the axle shafts.

The axle shafts do not use an inner

or outer bearing retainer. They are

held in the axle by means of C-locks,

positioned in a slot on the splined end.

These C-locks also fit into a machined

recess in the differential side gears

within the differential case. There is

no retainer bolt access hole in the axle

shaft flange.
procarmanuals.com

04-04-04
Rear Axle — Ford Light-Duty (WER)

04-04-04

REMOVAL AND INSTALLATION

AXLE HOUSING

Refer to Fig. 7.

REMOVAL

1.
Raise the vehicle on a hoist.

2.
Remove the wheels and tires

from the brake drums.

3.
Position a drain pan and loosen

the rear axle cover to housing attach-

ing bolts. Drain the housing.

4.
Remove the attaching (Tinner-

man) nuts that secure the brake drums

to the axle shaft flanges, and then re-

move the drums (Fig. 7).

5.
Remove the axle housing cover

bolts,
cover and gasket. Discard the

gasket. Remove the drain pan.

6. Disconnect the drive shaft at the

drive pinion companion flange. Re-

move the drive shaft from the trans-

mission extension housing. Install an

oil seal replacer tool in the transmis-

sion housing to prevent leakage. Refer

to the transmission group for the ap-

propriate tool.

7.
Disconnect the lower end of the

shock absorbers at the mounting

brackets.

8. Disconnect the track bar from

the axle housing stud. If the axle

housing is to be replaced, transfer the

stud to the new housing.

9. Position safety stands under the

rear frame members. Lower the vehi-

cle with the hoist and allow the axle

to lower far enough to relieve rear

spring tension.

10.
Remove the pinion shaft lock

bolt and pinion shaft (Fig. 2), differ-

ential pinion gears and thrust washers.

11.
Push the axle shaft(s) inward

toward the center of the axle housing.

Remove the C-locks from the inner

ends of the axles (Fig. 3). Remove the

axle shafts from the housing. Extreme

care must be used to avoid contacting

the axle shaft seal lip with any portion

of the axle shaft other than the seal

journal.

12.
Disconnect the vent hose from

the rear vent tube and remove all

brake lines from the axle housing re-

taining clips.

13.
Remove the brake backing

plate attaching nuts and the plates

from the axle housing. Suspend the

plates above the axle housing with

mechanics wire. The hydraulic brake

lines and the parking brake cables will

remain attached to the brake backing

plates.
14.
Support the rear axle housine

on a jack.

15.
Remove the right and left rear

springs and insulators.

16.
Remove the nuts, washers and

pivot bolts that connect the suspension

lower arms to the axle housing. Dis-

connect both arms from the axle

housing.

17.
Disconnect the upper suspen-

sion arm from the axle housing by re-

moving the pivot bolt, nut, lock wash-

er and two eccentric washers.

18.
Lower the rear axle to the floor

with the jack and remove the axle

from under the vehicle.

19.
Remove the wheel bearings and

oil seals with the tool shown in Fig. 4.

20.
If the axle housing is being re-

placed, transfer all the differential and

pinion parts to the new housing. Refer

to Section 4, Major Repair Operation

for the procedure.

INSTALLATION

1.
Lightly coat the wheel bearing

rollers with axle lubricant. Install

wheel bearings in the axle housing

with the tool shown in Fig. 5. The

bearings should seat firmly against the

shoulder.

2.
Wipe all lubricant from the oil

seal bore before installing the seal. If

axle housing is being replaced, new

seals must be installed.

3.
Inspect the original seal for

nicks,
scuffs or abnormal wear, and

replace if necessary. New seals are

pre-packed with lubricant and do not

require an oil soak.

4.
Install the seal with the tool

shown in Fig. 6. Installation without

the use of the proper tool will distort

the seal and cause leakage.

5. Raise the rear axle into position

under the vehicle with a hoist or floor

jack. Connect the suspension lower

arms to their mounting brackets on

the axle housing with pivot bolts and

nuts.
Do not tighten the mounting

bolts at this point.

6. Position the suspension upper

arm in its mounting bracket on the

axle housing and install the adjusting

bolt, eccentric washers, lock washer

and nut. Do not tighten the mounting

bolt at this point.

7.
Place the rear coil springs and

insulators into position in the pockets

provided.
8. Place the brake backing plates

on the axle housing flanges, install 4

attaching bolts and nuts and torque

them to specifications.

9. Position the brake lines to the

axle housing and secure them with the

retaining clips. If the axle housing is

new, install a new vent. When install-

ing the new axle vent apply a small

amount of Locktite (C5AZ-19554-B)

to prevent oil leakage between vent

and axle housing. Connect the vent

tube to the vent.

10.
Install the pinion side gears and

thrust washer.

11.
Slide the axle shafts into place

in the axle housing. Exercise care that

splines or any portion of the axle

shafts do not damage the oil seals and

that they engage with the splines of

the differential side gears.

12.
Install the axle shaft C-lock O-

ring and C-lock on the inner end of

the shaft and push the shaft outward

so that the shaft lock seats in the

counterbore of the differential side

gear.

13.
Position the pinion differential

gears and thrust washers 180 degrees

apart to the differential side gears.

Revolve the gear assembly until the

holes in the differential case are al-

igned with the pinion gears.

14.
Position the differential pinion

shaft through the case and pinions, al-

igning the hole in the shaft with the

lock bolt hole. Install the lock bolt

and tighten it to specification.

15.
Clean the gasket mounting sur-

face of the rear axle housing and the

cover. Install a new cover gasket,

cover and the attaching bolts. Torque

the bolts to specification.

16.
Raise the rear axle on a hoist

and remove the safety stands.

17.
Connect the track bar to the

mounting stud. Install the washer and

nut. Torque the nut to specification.

18.
Connect the two rear shock ab-

sorbers to the mounting brackets on

the axle housing and torque the at-

taching nuts to specification.

19.
Make sure that both the front

and rear pivot bolts of the upper and

the two lower arms are loose, then

raise the axle assembly to the con-

trolled height (Fig. 8). Hold the axle

at the controlled height by placing

blocks or pieces of steel pipe between

the axle housing and the bumper rear

screw on the side rail.procarmanuals.com

04-04-06
Rear Axle — Ford Light-Duty (WER)

04-04-06

20.
With the axle at controlled

height, torque the suspension upper

and lower arm front pivot bolts and

nuts to specifications. Torque the

lower arm to axle housing pivot bolts

and nuts to specifications.

21.
Remove the oil seal replacer

from the transmission extension hous-

ing. Install the drive shaft in the ex-

tension housing. Align the scribe

marks on the cups, flange and drive

shaft and connect the drive shaft at

the drive pinion flange. Torque the at-

taching bolts to specification
FRAME

TIGHTEN ARM

ATTACHING BOLTS

AT 5-45/64 INCH

HEIGHT POSITION
5-45/64 INCH

HEIGHT FOR

INSTALLATION

OF ARMS

E 1600-B

FIG.8—
Axle
Normal Curb Height

and Controlled Height for Arm

Installation
22.
Install the brake drum and at-

taching (Tinnerman) nuts.

23.
Install the wheel and tire on the

brake drum. Install the wheel covers.

24.
Adjust the drive shaft and pin-

ion angle to specification.

25.
Add the amount of specified lu-

bricant required to reach to the bot-

tom of the filler plug hole. Make sure

the rear axle is in running position.

Install the filler plug and torque it to

specification.

26.
Lower the vehicle.

4 MAJOR REPAIR OPERATIONS

DISASSEMBLY OF AXLE
The rear axle components are

shown in Fig. 9.

DIFFERENTIAL SIDE GEAR

AXLE SHAFT C-WASHER \

DIFFERENTIAL PINION SHAFT

THRUST WASHER

BEARING ASSEMBLY

CUP
THRUST WASHER

^^ DIFFERENTIAL PINION GEAR

BEARING ADJUSTING NUT

DIFFERENTIAL

PINION SHAFT

LOCK BOLT

LOCK WASHER
BOLT

LOCK WASHER

ADJUSTING NUT LOCK

DRIVE GEAR ATTACHING BOLT

BEARING CAP

AXLE HOUSING ASSEMBLY

PINION AND RING GEAR

PINION LOCATING SHIM(S)

BEARING CUP

BOLT

NUT

BEARING CUP

COLLAPSIBLE SPACER

AXLE SHAFT

E 1572-C

FIG. 9—Disassembled Light-Duty (WER) Rear Axleprocarmanuals.com

04-04-07
Rear Axle — Ford Light-Duty (WER)
04-04-07

RUNOUT CHECK

E 1573-A

FIG. 70—Checking Backlash and Runout—Light-Duty (WER) Axle

All service operations on the differ-

ential case assembly can be performed

with the axle housing in the vehicle.

1.
Raise the vehicle on a hoist.

2.
Position the drain pan under the

axle housing. Loosen the housing

cover attaching bolts. Drain the lubri-

cant from the housing.

3.
Make scribe marks on the drive

shaft end yoke and the rear axle shaft

companion flange to insure proper po-

sition of the drive shaft at assembly.

Disconnect the driveshaft from the

rear axle companion flange. Be care-

ful to avoid dropping the loose univer-

sal joint bearing cups. Hold the cups

on the spider with tape. Mark the

cups so that they will be in their origi-

nal position in relation to the flange

when they are reassembled. Remove

the drive shaft from the transmission

extension housing. Install an oil seal

replacer tool in the transmission ex-

tension housing to prevent transmis-

sion leakage. Refer to the transmis-

sion group for the appropriate tool.

4.
Raise the vehicle and place

jack-type stands under the rear frame

crossmember. Lower the vehicle on a

hoist and allow the axle to lower as

far as possible.

5.
Remove the axle housing cover

and gasket. Discard the gasket.

6. Perform the Inspection Before

Disassembly of Carrier procedure.

Refer to Part 4-1, Section 3 of this

Shop Manual.

7.
Remove the attaching (Tinner-

man) nuts that secure the rear brake

drums to the axle shaft flanges, and

then remove the drums.

8. Working through the differential

case opening, remove the pinion shaft

lock bolt and pinion shaft (Fig. 2).

9. Push the axle shafts inward

toward the center of the axle housing.

Remove the C-locks (Fig. 3) from the

inner ends of the rear axles. Remove

the axle shafts from the housing. Ex-

treme care must be used to avoid con-

tacting the axle shaft seal lip with any
portion of the axle shaft except the

seal journal.

10.
Remove the bearings and oil

seals from the axle housing as shown

in Fig. 4.

11.
Remove the pinion side gears

and the side gear thrust washers.

12.
Remove both side bearing ad-

justing nut locks (bolts).

13.
Install a dial indicator (Fig. 10),

and check and record the backlash

and ring gear runout.

14.
Mark one differential bearing

cap and the case to help in positioning

the parts properly during assembly.

15.
Remove the bearing cap retain-

ing bolts. Remove the bearing caps,

cups,
adjusting nuts and case assem-

bly.

16.
Hold the drive pinion flange

and remove the pinion nut (Fig. 11).

Discard the nut.

17.
Remove the pinion flange (Fig.

12).

18.
Drive the pinion out of the

front bearing cone and remove it from

the carrier housing. Remove and dis-

card the bearing spacer.

19.
With a hammer and drift re-

move the pinion shaft oil seal out

through the front of the carrier hous-

ing.

20.
Remove the pinion rear bearing

from the drive pinion shaft (Fig. 13).

21.
Measure the shim which is

found under the bearing cone with a

Tool-T57L-485T-A

or 4851-K

El 906A
Tool
-
T6SL-485UA
\

E 1574-A

FIG. 12—Drive Pinion Flange

Removal

1575-A

FIG. 13—Pinion Rear Bearing

Removal

00/
- T57L-4220-A

FIG. 11—Typical Drive Pinion

Shaft Nut Removal
E 1576-A

FIG. 14—Differential Bearing

Removal

micrometer. Record the thickness of

the shim.

DISASSEMBLY OF

DIFFERENTIAL CASE

1.
If the 2 differential side bearings

are to be removed from the differen-

tial case, use the tool shown in Fig.

14.procarmanuals.com

04-04-10
Rear Axle — Ford Light-Duty (WER)

04-04-10

the differential case and ring gear as-

sembly in the carrier without regard

to the matching of any particular gear

teeth.

12.
Slide the case assembly along

the bores until a slight amount of

backlash is felt between the gear teeth.

Hold the differential case in place.

13.
Set the adjusting nuts in the

bores so that they just contact the

bearing cups.

14.
Carefully position the bearing

caps on the carrier casting. Match the

marks made when the caps were re-

moved (Fig. 21).

15.
Install the bearing cap bolts

and lockwashers. As the bolts are

tightened, turn the adjusting nut with

the tool shown in Fig. 21.

16.
If the adjusting nuts do not turn

freely as the cap bolts are tightened,

remove the bearing caps and again in-

spect for damaged threads or incor-

rectly positioned caps. Tightening the

bolts to the specified torque is done to

be sure that the cups and adjusting
.BEARING CAP IDENTIFICATION-j

MARKS
A

T57L-4067-A

E 1583-A

27—Bearing Cap Installation

nuts are seated. Loosen the cap bolts,

and torque them to only 5 ft-)bs be-

fore making adjustments. Refer to

part 4-1, Section 2 of this shop manu-

al for backlash and bearing preload

adjustment procedures.

17.
Clean the marking compound

from the gear teeth.

18.
Install both side bearing adjust-

ing nut locks (bolts) and torque them

to specification.
19.
Install the differential pinion

side gears and thrust washers.

20.
Install the rear wheel bearings

seals,
rear axle shafts, wheels and tires

and the axle carrier cover as outlined

under Part 4-3, Section 2, Rear Axle

Shaft, Wheel Bearing and Oil Seal

Replacement, Steps 10 through 19.

21.
Raise the axle all the way up.

Rdnove the safety support stands.

22.
Connect the track bar to the

mounting stud. Install the washer and

retaining nut, and torque the nut to

specification.

23.
Remove the oil seal replacer

tool from the transmission extension

housing. Install the front end of the

drive shaft on the transmission.output

shaft. Align the scribe marks on the

cups,
flange and drive shaft and con-

nect the rear end of the drive shaft to

the axle U-joint flange. Torque the re-

taining bolts to specification.

24.
Lower the vehicle.procarmanuals.com

04-05-05
Specifications

04-05-05

SPECIAL TOOLS

FORD MERCURY, METEOR (Continued)

Ford Tool No.

T57L-4221-A1 or

Tool-4222-K

TOOL 6565-AB

TOOL 6565

TOOLS 4201-C

andD

TOOL-T57L-

4067-A

TOOL-T50T-100-A

T00L-T66L-

12132-B

CJ-6625 (Snap-

On)
Foniisr
NO.

4222-H

6565-AB

6565

4201-C

4067-B

—

—

—
Description

Differential Bearing Installer

Adapter

Dial Indicator

Differential Backlash and Runout

Gauge with Universal Bracket, Dial

Indicator and Bracket

Differential Bearing Adjuster Wrench

Impact Hammer-Long

Adapter

Puller
Ford Tool No.

TOOL-T60K-

7697-B

T00L-T65F-

1177-A

T00L-T65L-

4851-A

TOOL-OTC-951

T00L-T67P-

4616-A

TOOL-T53T-

4621-C
Fomor No.

—

—

—

—

—
Description

Transmission Extension Housing

Bushing Repiacer

Rear Wheel Bearing Oil Seal Repiacer

Flange (Universal Joint) Axle End

Remover

Universal Puller

Pinion Bearing Cups Repiacer

Pinion Bearing Cone Repiacer

COUGAR, FAIRLANE, FALCON,

Ford Tool No.

T50T-100-A

T58L-101-A

T62L-201-A

T56L-400-A

T57L-500-A

T00L-1175-AB

T50T-100-Aand

TOOL-1175-AB

T60K-1177-B

T60K-1225-Aor

T00L-1225-C

TOOL-1225-B

T00L-T54-P-

3044-A

T00L-T57L-

4067-A

T57L-4067-Aor

T60K-4067-A

TOOL-4201-C

andD

T65K-4204A or

T59L-4204-A

T00L-4221-AL

T57L-4221-A

T00L-4222-H

T66L-4235-A
Former No.

B-160

-

4851-A

-

1175-AB

1175-AE

1177-B

4067-B

4221 or

4211-A

4201-C

4067-E

4221-AL

4222-K

4222
MONTEGO, MUSTANG

Description

Impact Hammer

Puller Attachment

Handle Adapter

Puller

Bench Mounted Holding Fixture

Grease Seal Remover (Head Only)

Seal Remover

Rear Wheel Bearing Oil Seal

Axle Shaft Bearing Remover and Repiacer

Axle Shaft Searing Remover

Axle Shaft Bearing Repiacer

Front Suspension Upper and Lower Arm

Overhaul Tool Kit

Differential Bearing Adjuster Nut

Wrench

Limited-Slip Differential Check

Differential Backlash and Runout Gauge

With Universal Bracket, Dial Indicator

and Bracket

Differential Bearing Adjuster Nut

Wrench

Differential Bearing Cone Remover

Pilot (Use with T00L-4221C or

T00L-4851-A)

Differential Bearing Cone Repiacer

Differential Bearing Cone Repiacer

Rear Axle Shaft Assembly Remover

Adapter
Ford Tool No.

T57L-4614-A

T00L-4615-J

T60K-4616-A

T57L-4616-A

T57L-4616-A2

T55P-4616-A2

T00L-4621-K

T62F-4621A

T62F-4625-A

T55P-4676-A

T62F4676A

T53T-4851A

T57L-4851-A

T00L-4858-E

T65K-4204-A

T59L-4204-A

T00L-6565-AB

TOOL-6565
Former No.

4614

4615-J

4615-HF

4625-HR

4615-
E

andP

4615-
E

andF

-

4621-K

4625-AC

land 2

4676-G

4676-
H

4851-A

4858-D

4851-K

4858-
E

—

44211 and

44211-A

6565-AB

6565
Description

Drive Pinion and Drive Pinion Retainer

Assembly Support

Drive Pinion Front Bearing Cup Remover

Pinion Bearing Cup Repiacer

Pinion Front Bearing Cup Remover

Pinion Front Bearing Cup Repiacer

Pinion Rear Bearing Cup Repiacer

Drive Pinion Rear Bearing Cone Remover

Pinion Bearing Cone Repiacer

Drive Pinion Pilot Bearing Remover

and Repiacer

Drive Pinion Oil Seal Repiacer

Drive Pinion Oil Seal Repiacer

Flange (Universal Joint) Axle End

Remover

Universal Joint Flange Holder

Companion Flange and Pinion Bearing

Repiacer

Limited-Slip Differential Torque Check

Adapter

Locking Differential Torque Check

Adapter

Dial Indicator

T68P-4946-A - Traction-Lok Shim Template Toolprocarmanuals.com

05-01-01
05-01-01

Clutch
GROUP

5

PART
5-1
PAGE

Drive Shaft 05-01-01

PART
5-2

General Clutch Service 05-02-01
PART
5-3

Clutch

PART
5-4

Specifications
PAGE

05-03-01

05-04-01

PART
5-1
Drive Shaft

COMPONENT INDEX

DESCRIPTION

DRIVE SHAFT ANGLE CHECK

DRIVE SHAFT BALANCE CHECK

DRIVE SHAFT BALANCING

(Single Universal Joint)

DRIVE SHAFT DISASSEMBLY
AND

OVERHAUL

Single Universal Joint — Ford Design

Double Cardan Joint — Dana Design

Double Cardan Joint — Saginaw Design

DRIVE SHAFT REMOVAL
AND

INSTALLATION

DRIVE SHAFT RUNOUT CHECK
MODEL APPLICATION
All
Models

01-01

01-01

01-01

01-02

01-01
Ford
01-04

01-04

N/A

N/A
Mercury
01-04

01-04

N/A

N/A
Meteor
01-04

01-04

N/A

N/A
Cougar
01-04

01-04

N/A

N/A
Fairlane
01-04

01-04

N/A

N/A
Falcon
01-04

01-04

N/A

N/A
Montego
01-04

01-04

N/A

N/A
Mustang
01-04

01-04

N/A

N/A
Lincoln-
Continental
N/A

N/A

01-04

N/A
Thunderbird
N/A

N/A

N/A

01-05
Continental-
Mark
III
N/A

N/A

N/A

01-05

A page number indicates that the item
is for the
vehicle listed
at the
head
of
the column.

N/A indicates that
the
item
is not
applicable
to the
vehicle listed.

DRIVE SHAFT TESTS

DRIVE LINE BALANCE CHECK

If detailed parts
of the
drive shaft

are replaced
and
shaft vibration
is en-

countered after installation, disconnect

the shaft
at the
slip yoke. Rotate
the

slip yoke
180
degrees; then, reconnect

the shaft
to the
slip yoke.
If the
vibra-

tion persists, disconnect
the
shaft
at

the rear axle companion flange.
Ro-

tate
the
companion flange
180
degrees

and reconnect
the
shaft
to the
flange.
DRIVE LINE ANGLE CHECK

Vibration
or
"shudder" which
is no-

ticeable either
on
fast acceleration
or

when coasting, using
the
engine
for a

brake,
may be
caused
by the
rear axle

housing being loose
on the
rear

springs
or by
improper pinion angle.

Refer
to
Group
3,
Part
2 for
pinion

angle checking procedures.
If the
rear

axle U-bolts (Fairlane, Montego,

Mustang, Cougar, Falcon models
only)
are
loose, torque
the
nuts
to

specification.

DRIVE SHAFT RUNOUT CHECK

Using
a
dial indicator, check
the

runout
at
each
end and in the
middle

of
the
driveshaft.
The
rear check

should
be
made
on the
small tube
sec-

tion
of the
shaft between
the
balance

weights
and the
yoke welds. Drive-

shaft runout should
not
exceed 0.035

inch
at any one
point.

DESCRIPTION

The drive shaft
is the
means
of

transferring power from
the
engine,

through
the
transmission,
to the dif-
ferential
in the
rear axle,
and
then
to

the rear wheels.
The
drive shaft incor-

porates
two
universal joints
and a
slip
yoke
(Fig. 1) or two
double cardan

universal joints,
one at
each
end of the

shaft (Figs.
2 and 3).
Each double
procarmanuals.com