1969 FORD MUSTANG suspension

03-13-01
Specifications

03-13-01

PART 3-13 Specifications

FRONT
WHEEL
ALIGNMENT

Vehicle

Model

Mustang,
Cougar

Fairlane, Falcon

Mont
ego

Ford,
Mercury

Meteor

Thunderbird,

Mark III

Lincoln

Continental
Dimension

"C"

Inches

(I) 6.30

® 6.50

©4.20

® 4.20

©5.87
Dimension

"D"

Inches

©5.50 (Mustang)

6.35 (Cougar)

©6.72

©6.70

©6.70

©8.39
Alignment

Factors

Caster©

Camber©

Toe-in-Inches

Caster©

Camber©

Toe-in-Inches

Caster©

Camber©

Toe-in-Inches

Caster©

Camber®

Toe-in-Inches

Caster®

Camber®

Toe-in-Inches
Min.

-3/4°

+1/4°

1/16

-1
3/4°

•1/2°

1/8

0°

•1/4°

1/16

0°

•1/4°

1/16

-1/2°

•1/4°

0
Max.

+1 1/4°

+1 3/4°

5/16

+1/4°

+1°

3/8

+2°

+11/4°

5/16

+2°

+1 1/4°

5/16

-2
1/2°

+11/4°

1/4
Desired

+1/4°

+3/4°

3/16

•3/4°

+1/4°

3/16

+1°

+1/2°

3/16

+1°

+1/2°

3/16

•11/2°

+1/2°

1/8

©Maximum difference between wheels not to exceed 1/2° (setting). Maximum checking difference not to exceed 1° with caster and camber
with-

in specifications.

©Maximum difference between wheels not to exceed 1/2°.

©Vertical distance between bottom surface of spring tower on centerline of rebound bumper bolt and point on flat surface of upper suspension

arm midway between ball joint rivets.

©Shortest vertical distance between point on side member and axle housing.

©Distance from corner of lower flange sidemember front to center of bolt head (strut mounting bolt).

©Vertical distance between bottom of sidemember at center of axle bumper bracket and top of axle housing.

©Vertical distance between point on underside of crossmember pocket and point on top of drag strut.

©Distance from axle housing to surface on sidemember immediatly behind axle bumper.

WHEELBASEAND TREAD WIDTH-INCHES

FRONT WHEEL TURNING ANGLE

Vehicle Model

Mustang

Cougar

Fairlane, Montego

Falcon (except Station Wagon)

Falcon Station Wagon

Ford

Mercury, Meteor

Thunderbird (2-Door)

Thunderbird (4-Door), Mark HI

Lincoln Continental
Wheelbase

108.0

111.1

116.0

110.9

113.0

121.0

124.0

114.7

117.2

126.0
Tread

Front

58.5

58.5

58.8

58.8

58.8

63.0

63.0

62.0

62.0

62.4
Width

Rear

58.5

58.5

5«.5

58.5

58.5

64.0

64.0

62.0

62.0

61.0
Vehicle Model

Mustang,
Cougar

Fairlane, Falcon, Montego

Ford,
Mercury, Meteor

Thunderbird, Mark III

Lincoln Continental
Turning Angle of Outside Wheel

With Inside Wheel Turned 20°

18.68°

With Power Steering 17.88°

With Manual Steering 18.1°

With Power Steering 19.14°

With Manual Steering 18.96°

19.26°

17.71°

BALL JOINTS -RADIAL PLAY

STEERING WHEEL TURNING EFFORT

Vehicle Model

Cougar, Fairlane,

Falcon,
Montego,

Mustang

Ford,
Mercury,

Meteor, Thunderbird,

Mark III, Lincoln

Continental
Description

Lower Ball Joint

Upper Ball Joint

Lower Ball Joint

Upper Ball Joint
Radial Play-Max. Allowable

Replace if perceptibly loose

0.250
Inch

0.250
Inch

Replace if perceptibly loose
Vehicle Model

Ford,
Mercury, Meteor

Cougar, Fairlane, Falcon,

Montego, Mustang

Lincoln Continental, Mark III,

Thunderbird
Lbs.
Effort

5.0

6.5

3.75procarmanuals.com

03-13-05

Specifications

03-13-05

TORQUE LIMITS-FRONT SUSPENSION

MONTEGO, FALCON,
FAIR
LANE,
MUSTANG AND COUGAR

Description

Shock Absorber Upper Attachment

Shock Absorber Upper Bracket to Body

Front Suspension Compression Bumper to Body

Brake Backing Plate to Spindle

Upper Arm and Inner Shaft to Body

Spring Seat to Upper Arm

Shock Absorber to Spring Seat

Ball Joint to Spindle (Upper and Lower)

Wheel Bearing Adjusting Nut

Strut to Lower Arm

Lower Arm to Underbody

Stabilizer Bar Mounting Bracket to Underbody

Strut to Underbody

Stabilizer Bar to Lower Arm

Caliper to Spindle (Disc Brake) • Upper

- Lower

Strut to Underbody Slotted Nut
Ft • Lbs

Montego, Falcon, Fairlane

20-28

15-25

12-17

9-14 (Disc) 25-45 (Drum)

75-100

30-40

8-12

60-90 ©

17-25 ©

75-105

75-100

17-25

60-80

5-10

110-140

55-75
Mustang and Cougar

10-15

22-34

12-17

9-14 (Disc) 28-45 (Drum)

75-100

25-40

8-12

60-90 ©

17-25 ©

70-105

75-100

17-25

60-80

8-12

110-120

55-75

50-70 | 50-70

©Torquethe adjusting nut to 17-25 ft-lb. Locate nut lock on adjusting nut so ,ctstellations are aligned with cotter pin hole in spindle. Then,

backoff adjusting nut and nut lock so the next castellation aligns with the cotter pin hole.

TORQE LIMITS-fRONT SUSPENSION

FORD,
MERCURY, METEOR

Description

Lower Arm to No. 2 Crossmember

Upper Arm to Frame

Upper Arm Bumper

Brake Backing Plate and Cylinder Assembly

to Spindle

Stabilizer Bar to Lower Arm

Ball Joint to Spindle (Upper and Lower)
Ft Lbs

55-75

100-130

15-25

80-106

5-10

60-90®
Description

Brake Backing Plate to Spindle

Strut to Lower Arm

Stabilizer Bar to Frame

Strut to Frame

Shock Absorber Upper Attachment

Shock Absorber Lower Arm

Caliper to Spindle (Disc Brake)
Ft-Lbs

25-45

70-113

18-27

60-90 ©

20-28

8 12

120-130

©Torque to specification, then tighten the nut to the nearest cotter pin slot and insert the cotter pin.

TORQUE LIMITS-FRONT SUSPENSION

THUNDERBIRD, CONTINENTAL MARK

Description

Lower Arm to #2 Crossmember

Upper Arm to Frame

Upper Arm Bumper

Stabilizer Bar to Lower Arm

Ball Joint to Spindle (Upper and Lower)

Strut to Lower Arm

Stabilizer Bar to Mounting Bracket

Strut to Frame

Shock Absorber Upper Attachment

Shock Absorber to Lower Arm

Brake Splash Shield (Disc) to Spindle

Caliper to Spindle (Disc Brake)

Upper Bolt

Lower Bolt
Torque

Ft-Lbs

60-90

100-150

15-25

5-10

©60-90

70-113

8-12

©60-90

20-23

8-12

9-14

110-140

90-120

©Torque to minimum specification;
then,
tighten the nut to the nearest cotter pin slot and insert the cotter pin.procarmanuals.com

03-13-06

Specifications

03-13-06

TORQUE LIMITS-FRONT SUSPENSION

LINCOLN CONTINENTAL

Description

Brace-Front Suspension to Sidemember (Model 74A Only)

Drag Strut
to
Strut Bracket Assembly

Lower Arm Assembly to Front Crossmember
-
(Attach Bracket)

Lower Arm Assembly to No. 2 Crossmember

Drag Strut
to
Lower Arm Assembly

Wheel Spindle to Lower Arm Ball Joint

Front Wheel Spindle to Upper Arm Ball Joint Assembly

Upper Arm Inner Shaft
to
Upper Arm

Upper Arm and Shaft Assembly to No. 2 Crossmember

Shock Absorber Bracket Assembly to No. 2 Crossmember Bracket

Shock Absorber Assembly to No. 2 Crossmember Assembly (Top End)

Shock Absorber Assembly Lower Arm Spring Seat Reinforcement Assembly

Upper Ball Joint
to
Control Arm

Stabilizer Bar Assembly
to
Underbody

Stabilizer Bar
to
Lower Arm

Jounce Bumper Assembly
to
Strut (Lower Arm)

Front Splash Shield to Spindle

Caliper to Spindle
FtLbs

90-110

70-90

55-75

110-140

70-90

70-90

55-75

25-35

100-125

40-55

20-30

20-30

21-29

20-30

5-10

22-28

9-14

100-140

TORQUE LIMITS-REAR SUSPENSION

FORD, MERCURY, METEOR

Description

Shock Absorber
to
Frame (Upper Attachment)

Upper Arm to Axle Bracket (Nut)

Track Bar to Axle Track Bar Stud

Track Bar Stud to Axle

Track Bar
to
Frame (Bolt Torque)

Track Bar Stud to Axle Bracket (Nut)

Wheel Lug Nut

Brake Backing Plate and Bearing Retainer to Axle-All Cars except those with 240
or
302 CID Engines

Brake Backing Plate and Bearing Retainer to Axle-All Cars with 240
or
302 CID Engines

Shock Absorber to Axle (Lower Attachment)

Bumper Assembly
to
Frame

Lower Arm to Axle-Bolt

Lower Arm to Axle-Nut

Upper Arm
to
Frame-BoU

Upper Arm
to
Frame-Nut

Lower Arm
to
Frame-Bolt

Lower Arm
to
Frame-Nut

Bumper Assembly to No. 4 Crossmember

Universal Joint
U-Bolt
Nut

Air Leveling Compressor
to
Apron

Height Control Valve to Bracket

Height Control Valve Bracket to No. 4 Crossmember
FtLbs

20-28

90-100

80-105

100-130

80-105

80-105

70-115

50-70

20-30

50-35

9-13

90-120

70-90

90-120

70-90

90-120

70-90

9-13

10-15

10-13

17-25

9-13procarmanuals.com

03-13-07

Specifications

03-13-07

TORQUE LIMITS-REAR SUSPENSION

MONTEGO, FALCON, FAIR LANE, MUSTANG AND COUGAR

Description

Spring Shackle Bars to Body and Spring

Shock Absorber
to
Upper Mounting Bracket

Shock Absorber to Spring Clip Plate

Spring to Axle U-Bolt Nut

Wheel Lug Nut 5-Lug Wheel

Spring to Spring Front Hanger
•
Bolt

Spring to Spring Front Hanger
•
Nut

Universal Joint U-Bolt Nut -Std. Trans.

Universal Joint U-Bolt Nut -Auto. Trans.
Mont
ego,
Falcon, Fair lane

15-22

20-28

20-28

35-50

70-115

90-120

40-60

6-11

10-15
Mustang and Cougar

15-22

20-28

20-28

35-50

70-115

60-85

40-60

6-11

10-15

TORQUE LIMITS-REAR SUSPENSION

LINCOLN CONTINENTAL

Description

Brake Backing Plate Bearing Retainer to Axle

Spring Center Bolt

Spring Front Bracket Assembly to Rear Floor Sidemember Assembly

Spring Front Eye Stud and Washer Assembly to Spring Front Hanger Bracket

Spring U-Bolt

Spring Assembly
to
Spring Shackle Assembly

Spring Shackle Assembly
to
Spring Rear Bracket Assembly

Spring Rear Bracket Assembly
to
Rear Floor Sidemember Assembly

Shock Absorber Upper Attaching Bracket
to
Body Crossmember

Shock Absorber Assembly
to
Shock Absorber Upper Attaching Bracket

Shock Absorber Assembly to Axle

Axle Bumper Bracket
to
Underbody

Pinion Bumper Assembly to Axle Carrier
Ft Lbs

30-55

15-20

70-90

76-106

45-65

34-59

34-59

40-67

20-30

20-28

30-45

10-15

18-25

TORQUE LIMITS-REAR SUSPENSION

THUNDERBIRD, CONTINENTAL.MARK
III

Description

Shock Absorber
to
Frame (Upper Attachment)

Upper Arm
to
Axle (Front)

Track Bar to Axle Track Bar Stud

Track Bar Stud to Axle

Track Bar
to
Frame (Bolt Torqe)

Wheel Lug Nut

Brake Backing Plate and Bearing Retainer
to
Axle

Shock Absorber to Axle (Lower Attachment)

Bumper Assembly to Frame

Lower Arm
to
Axle - Bolt

Lower Arm
to
Axle- Nut

Upper Arm
to
Frame -Bolt

Upper Arm
to
Frame
•
Nut

Lower Arm
to
Frame • Bolt

Lower Arm to Frame
-
Nut

Bumper Assembly to No. 4 Crossmember
Ft-Lbs

20-28

70-90

80-105

100-130

70-90

70-115

50-75

50-85

Self-Tapping

90-120

70-80

90-120

70-90

90-120

70-90

Self-Tappingprocarmanuals.com

03-13-08
Specifications
03-13-08

SPECIAL SERVICE TOOLS

Tool No.

T50T-100-A

T59L-100-B

T58L-101-A

T53L-200-A

T62L-201-A

OTC-462

T57L-500-A

T69L-1102-A

Tool 1175-AB

Tool 1175-AH

T56P-1217-A

T60K-1217-A

Tool 1217-J

Tool 1217-K

Tool
1217- L

Tool 1217-M

T65P-3000-A, D

T65P-3000-B, C, E, F

T57P-3006-A

T60K-3005-A

T62F-3006-A

Tool 3044-A

T54P-3044-A

T60K-3044-A

T65P-3044-A

Tool 3068

Tool 3069-AA

Tool
3069-
M

Tool 3290-C

T65P-3524-A

T66P-3553-A, B

T66P-3553-C

T65P-3548-A

T62F-3576-A

T64K-3576-A

T64K-3576-B

T65P-3576-A, B

T65P-3576-C

Tool 3583-J

T65P-3590-F

T67L-3600-A

T65P-3805-A

T63P-5310-A

T64K-5310-A, B

T66P-5310-A, B

T64N-5781-A

T64K-5781-B

Tool 6306-AG

T63L-8620-A

T63L-10300-B

T65P-10300-B

T56L-33610-D

T68L-33610-A

Tool 33623-D

T65P-3A537-A

T65P-3A537-B

T69P-3A674-A

T65P-3A733-A

T65T-3B177-A

T68P-3B586-A

T68P-3B592-A

T68P-3B592-B

T64B-3C716-A

T65P-3C732-A

T65P-3D517-A

T65P-3D525-A

T65P-3D525-B

T65P-3D526-A

T69P-3D608-A

T69P-3D608-B

T65P-3D642-A

T67P-3D739-A
Description

Slide Hammer-Long

Slide Hammer-Short

Puller Attachment

Handle Adapter

Input Shaft Seal Installer

Tie Rod Separator (Owatonna Tool Co.)

Bench Mounted Holding Fixture

Front Wheel Bearing Remover

Grease Seal Remover (Head Only)

Grease Seal Replacer

Front Hub Bearing Cup and Grease Seal Replacer

Front Hub Bearing Cup and Grease Seal Replacer

Front Hub Outer Bearing Cup Replacer

Front Hub Inner Bearing Cup Replacer

Front Hub Outer Bearing Cup Remover

Front Hub Inner Bearing Cup Remover

Adjusting Bars-Caster and Camber

Alignment Spacers

Spindle Ball Joint Remover Press

Spindle Ball Joint Press Adapter Screw

Spindle Ball Joint Press Adapter Screw

Front Suspension Upper Arm Bushing Remover

Front Suspension Upper and Lower Arm Overhaul Kit

Front Suspension Lower Arm Bushing Remover and Replacer

Upper Arm Bushing Overhaul Kit

Front Suspension Upper Arm Bushing Adapter

Front Suspension Lower Arm Bushing Remover

Lower Arm Bushings-Remover and Replacer Kit

Tie Rod Ball Ends and Control Valve Ball Stud Remover

Input Shaft Bearing Remover and Installer

Spanner Wrench

Spacer

Oil Line Connector Seal Installer

Sector Shaft Bushing Remover and Replacer

Sector Shaft Needle Bearings and Seal Remover and Replacer

Sector Shaft Needle Bearings and Seal Remover and Replacer Adapter

Sector Shaft Bushing Remover and Installer

Remover and Installer Adapter

Control Valve Bearing and Seal Remover and Replacer

Steering Pitman Arm Remover

Steering Wheel Remover

Ring Compressor-Rack Piston

Front Coil Spring Remover and Replacer

Adapters

Adapters

Rear Spring Front Bushing Remover and Installer

Rear Spring Bushing Adapter

Crankshaft Damper Remover and Power Steering Pump Sprocket Replacer

Bent Tension Gauge

Pulley Remover

Alternator Pulley Replacer

Pressure Testing Gauge Assembly

Bypass and Orifice Gauge

Pump Oil Seal Pilot

Bearing Preload Spanner Wrench

Adjuster Plug Seal Protector

Fixture Adapter Plate

Power Steering Pump Pulley Remover

Front Suspension Bushings Remover and Replacer

Pump Housing Hole Plugging Tool

Pump Shaft Seal Replacer

Pump Shaft Seal Protector

Insulator Remover and Replacer Socket

Lock Spring Installing Hook

Rack Piston Arbor

Adjuster Plug Bearing Remover and Installer

Thrust Bearing Retainer Installer Adapter

Adjuster Plug Seal Installer

Pin Straightness Checking Block

Pin Guide Support

Sector Shaft Seal Installer

Pivot Pin Removerprocarmanuals.com

04-02-01

Rear Axle
—
Removable Carrier Type

04-02-01

PART
4-2
Rear Axle—Removable Carrier Type

COMPONENT INDEX

AXLE HOUSING (Coil Spring Suspension)

Cleaning and Inspection

Removal and Installation

AXLE HOUSING (Leaf Spring Suspension)

Cleaning and Inspection

Removal and Installation

AXLE SHAFT

Cleaning and Inspection

Removal and Installation

CONVENTIONAL DIFFERENTIAL

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

DIFFERENTIAL BEARINGS AND RING

GEAR

Adjustment

Cleaning and Inspection

Removal and Installation

DIFFERENTIAL CARRIER

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

LIMITED SLIP DIFFERENTIAL

Cleaning and Inspection

Description

Disassembly and Overhaul

Removal and Installation

PILOT BEARING

Cleaning and Inspection

Removal and Installation

PINION AND RING GEAR

Cleaning and Inspection

Removal and Installation

PINION BEARING

Cleaning and Inspection

Removal and Installation

PINION BEARING RETAINER

Cleaning and Inspection

Removal and Installation

PINION SPACER (Collapsible)

Removal and Installation

PINION OIL SEAL

Removal and Installation
MODEL APPLICATION
All
Models

01-10

02-04

01-10

02-13

02-08

02-19

01-10

02-19

01-10

02-13

02-08

01-10

02-03

02-13

02-13

01-10

02-15

01-10

02-15

01-10

02-15

01-10

02-15

02-04
J

01-09

02-08

N/A

N/A

02-17
Mercury
01-09

02-08

N/A

N/A

N/A
Meteor
01-09

02-08

N/A

N/A

02-17
Cougar
N/A

N/A

01-09

02-11

02-17
Fairlane
N/A

N/A

01-09

02-11

02-17
Falcon
N/A

N/A

01-09

02-11

02-17
Montego
N/A

N/A

01-09

02-11

02-17
Mustang
N/A

N/A

01-09

02-11

02-17
Lincoln-
Continental
N/A

N/A

01-09

02-11

N/A
Thunderbird
01-09

02-08

N/A

N/A

N/A
Continental-
Mark
III
01-09

02-08

N/A

N/A

N/A

A page number indicates that the item is
for
the vehicle listed
at
the head
of
the column.

N/A indicates that the item is not applicable
to
the vehicle listed.
procarmanuals.com

04-02-08
Rear Axle — Removable Carrier Type

04-02-08

REMOVAL AND INSTALLATION

CARRIER ASSEMBLY

REMOVAL

1.
Raise the vehicle on a hoist and

remove the two rear wheels and tires.

2.
Remove the two brake drums (3

Tinnerman nuts at each drum) from

the axle shaft flange studs. If diffi-

culty is experienced in removing the

drums, remove the brake adjuster

knockout slug or rubber plug (if so

equipped) and back off the brake

shoes.

3.
Working through the hole pro-

vided in each axle shaft flange, re-

move the nuts that secure the rear

wheel bearing retainer plate. Pull each

axle shaft assembly out of the axle

housing using axle shaft remover,

Tool 4235-C. (Fig. 4). Care must be

exercised to prevent damage to the

production-type synthetic oil seal, if so

equipped. Any roughing or cutting of

the seal element during removal or in-

stallation can result in early seal fail-

ure.
Install a nut on one of the brake

backing plate attaching bolts to hold

the plate to the axle housing after the

shaft has been removed. Whenever a

rear axle shaft is replaced, the wheel

bearing oil seals must be replaced.

Remove the seals with tool 1175AB.

4.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position at as-

sembly. Disconnect the drive shaft at

the rear axle U-joint. Hold the cups

on the spider with tape. Mark the

cups so that they will be in their orig-

inal position relative to the flange

when they are assembled. Remove the

drive shaft from the transmission ex-

tension housing. Install an oil seal re-

placer tool in the housing to prevent

transmission leakage. Refer to the

transmission group for the appropriate

tool.

5.
Clean area around carrier to

housing surfaced with a wire brush and

wipe clean, to prevent dirt entry into

the housing. Place a drain pan under

the carrier and housing, remove the

carrier attaching nuts, and drain the

axle.
Remove the carrier assembly

from the axle housing.

INSTALLATION

Synthetic production-type wheel

bearing seals must not be cleaned,

soaked or washed in cleaning solvent.

1.
Clean the axle housing and

shafts using kerosene and swabs. To

avoid contamination of the grease in
the sealed ball bearings, do not allow

any quantity of solvent directly on the

wheel bearings. Clean the mating sur-

faces of the axle housing and carrier.

2.
Position the differential carrier

on the studs in the axle housing using

a new gasket between carrier and

housing. Install the carrier-to-housing

attaching nuts, and torque them to

specifications.

3.
Remove the oil seal replacer tool

from the transmission extension hous-

ing. Position the drive shaft so that

the front U-joint slip yoke splines to

the transmission output shaft.

4.
Connect the drive shaft to the

axle U-joint flange, aligning the scribe

marks made on the drive shaft end

yoke and the axle U-joint flange dur-

ing the removal procedure. Install the

U-bolts and nuts and torque to speci-

fications.

5.
If the synthetic, production-type

wheel bearing seals were replaced with

service-type leather seals, soak the

new rear wheel bearing oil seals in

SAE 10 oil for 1/2 hour before instal-

lation. Wipe a small amount of an oil

resistant sealer on the outer edge of

each seal before it is installed. Do not

put any of the sealer on the sealing

lip.
Install the oil seals in the ends of

the rear axle housing with one of the

tools shown in Figs. 10 and 12.

Tool

T65F-1177.A

E 1571-A

FIG. 12—Rear Axle Shaft Bearing

Seal Installation

6. Install the two axle shaft assem-

blies in the axle housing. Care must

be exercised to prevent damage to the

oil seals. The shorter shaft goes into

the left side of the housing.

Carefully slide the axle shaft into

the housing so that the rough forging

of the shaft will not damage the oil

seal. Start the axle splines into the

differential side gear, and push the

shaft in until the bearing bottoms in

the housing.
7.
Install the bearing retainers on

the attaching bolts on the axle housing

flanges. Install the nuts on the bolts

and torque to specifications.

8. If the rear brake shoes were

backed off, adjust the brakes as out-

lined in Part 2-1 and install rubber

plugs in the adjuster slots.

9. Install the two rear brake drums

and the drum Tinnerman nuts.

10.
Install the rear wheels and tires.

11.
Fill the rear axle with specified

lubricant.

AXLE HOUSING (COIL

SPRING SUSPENSION)

REMOVAL

1.
Remove the carrier assembly

from the axle housing as outlined in

Differential Carrier Removal and In-

stallation.

2.
Position safety stands under the

frame rear members, and support the

axle housing with either a floor jack

or hoist.

3.
Disengage the brake line from

the clips that retain the line to the

axle housing.

4.
Disconnect the vent tube from

the rear axle housing.

5.
Remove the brake backing plate

assemblies from the axle housing, and

support them with wire. Do not dis-

connect the brake line.

6. Disconnect the lower studs of the

two rear shock absorbers from the

mounting brackets on the axle housing

(Fig. 13 and 14).

7.
Remove the attaching nut and

washer, and disconnect the track bar

from the mounting stud on the axle

housing bracket.

8. Lower the axle housing until the

coil springs are released. Lift out the

coil springs and insulators.

9. Remove the nuts, washers and

pivot bolts that connect the suspension

lower arms to the axle housing. Dis-

connect both arms from the axle

housing.

10.
Disconnect the upper suspen-

sion arm from the axle housing by re-

moving the pivot bolt, nut, lock wash-

er and the two eccentric washers (Fig.

13 and 14).

11.
Lower the axle housing and re-

move it from under the vehicle.

INSTALLATION

1.
Transfer the track bar mounting

stud from the old to the new housing.procarmanuals.com

REAR SPRING

5560

VENT

TUBE

INDENT TOWARD

FRONT OF VEHICLE
UPPER ARM

5500

LEFT ARM INDENTED

BY 2 NOTCHES IN BUSHING FLANGE

F 1353-A

f/Q.
J3—Rear Axle Installation—Typical Coil Spring Suspensionprocarmanuals.com