1967 CHEVROLET CAMARO Wiring

ELECTRICAL-BODY AND CHASSIS 12-3

Fig.
2 - T-3 Safety Aimer

wearing away the insulation due to vibration.

By referring to the wiring diagrams, circuits may be

tested for continuous circuit or shorts with a conventional

test lamp or low reading volt meter.

HEADLAMP ADJUSTMENT-

T-3 HEADLAMPS

CAUTION: Check and tighten radiator support

grille retaining bolts prior to attempting head-

lamp aiming. Distorted grille or supports in

this area will hinder proper aiming of head-

lamps. On Corvette models make sure head-

lamp panel is adjusted properly - refer to

"Headlamp Panel Travel Adjustment".

When aiming headlamps, vehicle should be filled to ca-

pacity with gas, oil, and water but no load. Tires should

be uniformly inflated to recommended pressure.

the T-3 Safety Aimer-Type B (fig. 2), is used for the

headlamp aiming description that follows. An adapter is

required with the Type B T-3 Aimer when adjusting the 7

inch headlamp used on the Chevy n vehicle.

1.
Drive vehicle onto selected aiming area. Bounce

vehicle several times and allow to settle.

2.
Remove headlamp bezels.

3.
Mount the T-3 Aimers on either the No. 1 or No. 2

pair of headlamps so that "the points of the headlamps

engage the smooth inner ring of the aimers.
HORIZONTAL

AIMING

SCREW

STRING OVER

"2R" ON AIMER ARM

Fig.
4—-Headlamp Horizontal Adjustment

NOTE:
In the dual headlamp installation, the

inboard unit is designated No. 1 and the outboard

unit is designated No. 2.

4.
Secure the aimers to the headlamp units by firmly

pressing knob at center of each aimer (fig. 3). Ro-

tate crossarms inboard to approximate horizontal

position.

NOTE:
Moisten suction cups slightly to obtain

maximum holding force.

5. With both aimers in place, knot both ends of elastic

string and, using slots provided, fasten string across

horizontal crossarms of each aimer.

6. Rotate both aimers so that the string just clears the

points on the crossarms.

HORIZONTAL ADJUSTMENT

7. a. Turn horizontal aiming screw, Figure 4, on left-

VERTICAL ADJUSTMENT SCREW

Fig.
3 - Installing Aimer on Headlamp Unit
Fig.
5 - Headlamp Vertical Adjustment

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-5

Fig.
8—Turning Level Adjusting Screw to Calibrate Aimer

HEADLAMP PANEL TRAVEL ADJUSTMENT

Corvette (Fig. 9)

The headlamp panel travel is limited by two adjusting

screws which are located on the arms of the shaft

mounted stop.
Fig.
9—Headlamp Panel Travel Adjusting Screw

1.
Raise hood and as a safety precaution install a bolt

through the hole in the hood support - secure bolt

with a nut.

2.
Adjusting screw (A) limits headlamp panel travel in

open position - adjust this screw so that mounting

face of panel is within 2 degrees of vertical in the

fully open position.

NOTE: Each headlamp operates independently

of the other, therefore individual adjustment is

required for each panel.

3.
Adjusting screw (B) limits headlamp panel travel in

closed position - adjust this screw so that panel is

flush to upper body panel in the fully closed position.

4.
Lock both screws by tightening lock nut against stop.

5.
Remove safety bolt as installed in Step 1 and close

the hood.

SERVICE OPERATIONS

FRONT LIGHTING

HEADLAMP REPLACEMENT (Figs. 10 and 13)

1.
On Corvette and Camaro Rally Sport models, rotate

the headlamp panel to the open position.

2.
Remove headlamp bezel retaining screws and remove

bezel. On Chevrolet, Chevelle and Camaro models

lift bezel to disengage retaining tabs from slots in

filler panel.

3.
On Chevy n models remove three retaining ring at-

taching screws. On other models disengage spring

from the retaining ring and remove two attaching

screws.

4.
Remove retaining ring, disconnect sealed beam unit

at wiring connector and remove the unit.

5.
Attach connector to replacement unit and position

unit in place making sure the number molded into the

lens face is at the top.

NOTE: In the dual headlamp installation the

inboard unit (NO. 1) takes a double connector, the
outboard unit (No. 2) takes a triple connector

plug.

6. Position retaining ring into place and install the re-

taining ring attaching screws and spring (as

applicable).

7.
Check operation of unit and install the headlamp

bezel.

PARKING LAMP REPLACEMENT

Bulb

1.
Remove two lens retaining screws and disengage lens

from housing.

2.
Replace bulb, check operation of lamp, reinstall lens

and retaining screws.

Lamp Housing

Chevrolet, Chevelle and Chevy II (Figs. 10 and 11)

1.
Disconnect lamp wire assembly in-line connector

from wiring harness.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-6

\ \

CHEVROLET
CHEVELLE

CHEVY II
CAMARO

Fig.
10 - Headlamp Assemblies (Exc. Corvette)

1.
2.
Remove two bolts retaining housing assembly in Corvette (Fig. 12)

bumper and remove housing.

3.
Remove lens retaining screws, lens and bulb from

housing assembly and transfer to new housing unit.

4.
Connect lamp wiring assembly to harness assembly,

housing and check operation of lamp.

5. Position lamp assembly in place and.install retaining

bolts.

Camaro (Fig. 10)

1.
Raise hood.

2.
Disconnect wiring harness at rear of lamp socket.

3.
Remove attaching nut and disconnect ground wire at

sheet metal connection.

4.
Remove retaining nuts and housing from grille

opening.

5. Transfer lens and bulb to new unit.

6. To install, position lamp housing to grille opening

and install retaining nuts.

7. Connect ground wire to attaching point and install

retaining nut.

8. Connect wiring harness to lamp socket and check

operation of lamp.
Raise hood and disconnect harness connector from

lamp unit skirt-mounted
connector;
then
remove'lamp

unit connector from underside of skirt.

Working at the forward portion of the wheel well, re-

move the two lamp assembly retaining nuts and re-

move the lamp assembly and support from the

vehicle.

Route the lamp assembly lead wires through fender

cutout and position support over lead wires.

Position lamp unit studs through support and install

retaining nuts, making sure that the studs are

horizontal.

Connect harness to lamp unit skirt-mounted connec-

tor and close vehicle hood.

FENDER LAMP SERVICE (Fig. 11)

Chevrolet 16600 Models

1.
Disconnect parking lamp wiring from forward har-

ness connector.

CHEVROLET CHASSIS SERVICE MANUAL

EL«C7RICAL-BODY AND CHASSIS 12-7

PARKING
A

LAMP*
2.
Remove two screws retaining lens housing to the

lamp assembly and remove lens unit.

3.
Replace bulb, lens or housing as required and posi-

tion assembly to fender opening. Make sure wiring

Fig.
11 - Parking and Fender Lamps (Chevrolet)

Fig.
12 - Parking Lamp Installation (Corvette)

Fig.
13 - Headlamp Panel and Motor Details (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-8

is inserted through radiator support opening.

Remove two screws retaining lamp assembly to

lower sheet metal.

Remove three screws retaining lamp assembly to

lender.

To replace lamp assembly, reverse removal proce-

dure and check operation of the unit.
is aligned with flat on pivot shaft. Install stop lock

bolt and torque bolt to 45-60 in, lbs. Make sure that

side-to-side panel alignment is not changed when in-

stalling and tightening the stop.

CAUTION: Do not exceed specified torque

when tightening stop lock bolt.

HEADLAMP PANEL REPLACEMENT-CORVETTE

Refer to Figure 13 for Panel Mounting details.

1.
Remove engine compartment hood as outlined in

Section 1.

2.
Actuate headlamp panel to the open position.

NOTE:
In the event headlamp motor is inop-

erative, manual positioning of the panel can be

accomplished by turning the knurled knob at in-

board end of motor. As an assist in manual

operation of panel, apply light hand pressure to

panel in desired direction of rotation.

3.
Remove positive lead from battery terminal.

4.
Remove headlamp bezel retaining screws and bezel.

5. Remove the sealed beam housing unit as an assem-

bly - disconnect sealed beam leads at harness con-

nector and remove connector from sealed beam

leads;
remove the housing-to-panel retaining screws

and remove housing unit and wiring from panel.

6. Remove motor from panel pivot shaft - see motor

removal procedure. Then remove the panel stop

from panel inboard pivot shaft, and disconnect switch

lead wires from panel, support-mounted motor

switch.

7. Remove the panel retaining bolt access hole plugs

from inside the panel then rotate panel as required

and remove the retaining bolts and slide supports

from ends of panel pivot shaft. Remove bearing, felt

seal, retainer and washer from inboard pivot shaft.

8. Remove panel from its location by alternately disen-

gaging pivots from their retaining slots and with-

drawing unit forward through opening in body (fig.

14).

9. Loosen alien screw in spacer and disassemble parts

from the panel outboard pivot shaft.

10.
Install washer, retainer, felt seal, bearing and

spacer, in that order, to panel outboard pivot shaft.

Do not tighten spacer on shaft at this time.

11.
Position panel in body opening and index panel pivot

shafts in retaining slots; then loosely install support

retaining bolts.

12.
Install washer, retainer, felt seal, bearing and sup-

port, in that order, to panel inboard pivot shaft, and

loosely install support retaining bolts. -

13.
Check side-to-side alignment of panel, making sure

that there is no panel-to-body contact; position

spacer snugly against bearing; then tighten spacer

seat screw to 30-50 in. lbs.

14.
Install stop on panel inboard shaft so that it rests

against bearing, being sure that index mark on stop
15.
Check and align panel to body as follows:

a. Tighten panel pivot support bolts snugly but still

allowing panel to" be moved by applying hand

pressure.

b.
Position panel to the closed position and align

with body so that all surfaces are flush.

c. With the panel in the closed position the outboard

access hole is aligned with the forward bolt head.

Tighten this bolt with the panel in the closed

position - access to bolt head can be obtained by

working through opening between the hood and

body.

d. Rotate panel to obtain access to each bolt head

and torque bolts to 100-140 in. lbs.

e. Connect switch lead wires to support-mounted

limit switch.

16.
Install seaLed beam housing unit and at the same time

position sealed beam lead wires through panel out-

board pivot shaft. Install housing unit retaining

screws and install lead wires in connector, making

sure to match colors between harness and connector.

17.
Install motor assembly - see motor replacement

procedure.

18.
Connect positive lead to battery terminal.

19.
Adjust headlamp panel as outlined under "Headlamp

Panel Travel Adjustment".

20.
Adjust headlamp aiming as outlined under "Headlamp

Adjustment".

21.
Install headlamp bezel and engine compartment

hood - refer to Section 1 for hood installation.

Fig.
14
- Headlamp Panel Removal (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-9

Fig.
15 - Headlamp Panel Actuating Motor Mounting (Corvette)'

HEADLAMP PANEL MOTOR-CORVETTE (Fig. 15)

Removal

1.
Raise hood and as a safety precaution install a bolt

through the hole in the hood support - secure bolt

with a nut.

2.
Remove positive lead from battery terminal.

3.
Disconnect motor lead wire and position it out of the

way.

4.
Turn the knurled knob at inboard end of motor until

the gear seems to turrj freely - turn the knob in one

direction until a definite drag is experienced, then

rotate knob approximately six complete turns in the

opposite direction.

NOTE:
The above step is necessary to produce

a no-load condition on the drive gear and to per-

mit separation of motor from the panel pivot

shaft.

5. Remove the retainer from groove in motor locating

stud then remove the motor-to-support retaining

screw and remove motor assembly from the vehicle.

Installation

1.
Rotate motor and headlamp panel as required to align

slot in motor with headlamp panel pivot shaft, and

install motor on shaft so that the bracket is aligned

with the locating stud.

NOTE:
It may be necessary to turn knurled

knob on end of motor to permit alignment of

motor with shaft.
Slide motor onto shaft until it seats against shaft

shoulder; then install retainer in groove on locating

stud.

Install motor-to-support retaining screw making

sure ground wire is installed between screw head and

bracket.

Connect motor lead wires, making sure that contacts

are clean and that connection is secure.

Connect positive lead battery terminal, remove bolt

from hood support, close hood and check operation of

headlamp panel.

HEADLAMP MOTOR REPLACEMENT-

CAMARO (Fig. 16)

1.
Disconnect battery ground cable and when working on

right headlamp unit, remove battery from vehicle to

gain access to housing retaining bolts.

2.
Remove bezel retaining screws and bezel.

3.
Remove headlamp cover retaining screws and cover

from door assembly.

4.
Manually open door assembly (push door toward cen-

ter of vehicle) and disconnect limit switch

connections.

5. Remove four screws retaining assembly to radiator

support (note location and number of shims, if any).

6. Rotate assembly toward center of vehicle until rear

of unit is exposed, then disconnect wiring connectors

at headlamp and motor assemblies.

7. Rotate assembly until headlamp is facing downward

and carefully remove the assembly from the vehicle

opening.

8. Remove nut attaching motor assembly to pivot arm.

9. Remove two nuts and bolts retaining motor assembly

to base plate and remove motor assembly.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-10

10.
To install, replace motor assembly, and reverse re-

moval procedure.

REAR LIGHTING SERVICE

TAIL, STOP AND DIRECTIONAL LAMPS

Bulb Replacement (Fig. 17)

1.
Disconnect lamp socket from rear of lamp unit and

remove bulb from socket.

NOTE:
Bulb removal on station wagon models

and Corvette requires, removal of the lens to

gain access to the bulb.

2.
Replace bulb and plug socket back into lamp housing.
Lamp Housing Replacement

Chevrolet, Chevelle Station Wagon,

Camaro and Chevy II (Fig. 17)

1.
Disconnect bulb socket from rear of lamp unit.

NOTE:
On station wagons remove lens to gain

access to lamp or screws securing lamp housing

to body.

2.
Remove nuts at rear of housing retaining lamp hous-

ing to vehicle body, remove housing from vehicle.

3.
Remove lens retaining screws or nuts, remove lens

and transfer to new housing unit.

4.
To install reverse removal procedure and check op-

eration of lamp unit.

HEADLAMP

WIRING ASSEMBLY
MOTOR

INSTALLATION

TO PARKING LAMP

TO RETR. HDLP. MOTOR

TO HEADLAMP
HEADLAMP

DOOR ASSEMBLY

Fig.
16- Headlamp Motor Installation (Comoro)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-14

BACKING LAMPS

lamp Housing Replacement (Fig. 19)

Bumper Installation

1.
Remove two screws retaining housing assembly in

the bumper and remove housing.

'2.
Disconnect lamp wire assembly connector from wir-

ing harness.

3.
Remove lens retaining screws, lens and bulb from

housing assembly and transfer to new housing unit.

4.
Connect lamp wiring assembly to harness assembly,

housing and check operation of lamp.

•5.
Position lamp assembly in place and install retaining

screws.

Corvette (Fig. 18)

1.
Remove license plate and bracket assembly.

2.
Remove tailpipe extensions and rear body valance

panel.

3.
Remove backing lamp attaching nuts.

4.
Disengage backing lamp assembly from body opening

and disconnect wiring harness at rear of lamp.

5. Transfer bulb, gasket and lens to replacement

housing.

6. Connect chassis wiring connector to housing and po-

sition lamp assembly to body opening.

7. Attach ground wire to housing and install retaining

nuts to housing.

8. Install body valance panel.

9. Position license plate assembly to body and install

retaining screws.

LICENSE PLATE LAMP SERVICE

Lamp Housing

1.
Remove the lamp assembly retaining screws and re-

move lamp assembly from mounting location (rear

bumper center face bar most models). On Corvette

models remove rear valance panel.

2.
Disconnect lamp wiring from chassis harness con-

nector (inside trunk on some models).

3.
Force grommet and Wiring down through body open-

ing (where applicable) and remove assembly from

vehicle.

4.
To install replacement unit, insert grommet and wir-

ing through body opening where applicable and con-

nect wiring to chassis harness.

5. Position assembly and install retaining screws. On

Corvette models make sure ground wire is properly

installed.

6. Check operation of lamp assembly.

iuib Replacement

1.
Remove lens retaining screws and lens.

NOTE:
On Camaro models loosen housing re-

taining screws.

2.
Remove and replace bulb.

3.
Position lens and install retaining screws.
AUTOMATIC TRANSMISSION

QUADRANT LAMP REPLACEMENT

Chevrolet (Fig. 20)

1.
Remove four screws retaining lower mast jacket

cover to upper cover.

2.
Remove two screws retaining upper cover to instru-

ment console.

3.
Remove two screws securing shield to upper cover

assembly.

4.
Remove and replace bulb.

5. Position shield to upper cover assembly and install

retaining screws.

6.' Position upper cover assembly to instrument console

and install retaining screws.

7. Position lower cover and install four retaining

screws.

Chevy II and Camaro (Fig. 21)

1.
Remove two screws attaching retainer and dial to

directional signal housing; remove retainer and dial

face from housing.

2.
Remove cap and bulb.

3.
Replace bulb and cap, then position dial and retainer

to housing.and install attaching screws.

Fig.
20 - Dial Quadrant Lamp — Chevrolet

1.
Upper Cover

2.
Shield

3. Lamp and Socket
4.
Dial Pointer

5.
Lower Cover

CHEVROLET CHASSIS SERVICE MANUAL