1967 CHEVROLET CAMARO transmission

ENGINE 6-31

Chevy II

1.
Disconnect battery positive cable.

2.
Drain engine oil.

3.
Disconnect and remove starter.

4 Disconnect steering idler arm bracket at right hand

frame rail and swing steering linkage down for pan

clearance.

5.
Disconnect* exhaust pipes at manifolds and allow

pipes to hang free.

6. Remove oil pan and discard gaskets and seals.

Corvette

1.
Disconnect battery positive cable then remove oil

dipstick and tube.

2.
Raise and support vehicle then drain engine oil.

3.
Remove starter and flywheel underpan.

4.
Disconnect steering linkage idler at frame and lower

the linkage.

5.
Remove oil pan and discard gaskets and seals.

6. On Hi-Performance engines, the oil baffle must

be removed before additional operations can be

performed.

NOTE: On the 427 cu. in. engine, the oil pan

has three 1/4" x 20 attaching bolts at crankcase

front cqver. One located at each corner and one

at lower center.

Installation

1.
Thoroughly clean all gasket sealing surfaces.

NOTE: Use a new pan. gasket set.

2.
Install side gaskets on pan rails, using.gasket sealer

as a retainer.

3.
Install rear oil pan seal in groove in rear main

bearing cap with ends (fig. 9V) butting side gaskets.

4.
Install oil pan front seal in groove in .crankcaee front

cover, with ends butting side gaskets.

5.
If crankshaft was rotated while £>an was off, place

timing mark at 6:00 o'clock position.

6. Install oil pan and torque bolts to specifications.

NOTE: On 396 and 427 cu. in. engines, start

three 1/4" x 20 bolts into crankcase front cover

before tightening, any other pan bolts.

7.
Complete installation as follows:

Chevrolet
and Camaro

a. Using a suitable jack (and a block of wood to pre-

vent damaging oil pan) raise engine enough to re-

move 2" x 4" wood blocks, then lower engine.

b.
On vehicles equipped with automatic transmission

install converter housing underpan.

c. Install through bolts in engine front mounts.

d. Install and connect starter. Connect steering rod

at idler lever.

e. Lower vehicle and install fan blade.

f. Cbnnnect lower radiator hose, then install oil dip

stick tube and dip stick.

g. Connect distributor cap and battery positive

cable.

h. Fill radiator with coolant and fill engine with oil,

then start engine and check for leaks.

Chevelle

a. On vehicles equipped with automatic transmission
Fig.
9V - Oil Pan Gasket and Seal Location

install converter housing underpan.

b.
.Install starter.

c. Install, engine as outlined.

Chevy II

a. Connect exhaust pipe to manifold flange using new

packing seals.

b.
Connect steering idler arm bracket.

c. Connect starter wires..

d. Connect battery cable.

e. Fill with oil, start engine and check for leaks.

Corvette

a. Connect steering linkage.

b.
Install oil dip stick tube and dip stick then con-

nect battery cables.

c. Fill engine with oil, then start engine and check

for leaks.

OIL PUMP

Removal

1.
Remove oil pan as outlined.

2.
Remove pump to rear main bearing cap bolt and re-

move pump and extension shaft.

Installation

1.
Assemble pump and extension shaft to rear main

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-37

Fig.
27V—Removing Camshaft

4.
Set dial indicator on zero, then rotate the damper

slowly, or attach an auxiliary starter switch and

"bump" the engine over, until the push rod is in the

fully raised position.

CAUTION: The primary distributor lead must

be disconnected from the negative post on the

coil and the ignition switch must be in the on

position. Failure to do this will result in a dam-

aged grounding circuit in the ignition switch.

5.
Compare the total lift recorded from the dial indica-

tor with specifications.

6. Continue to rotate the crankshaft until the indicator

reads zero. This will be a check on the accuracy of

the original indicator reading.

7.
If camshaft readings for all lobes are within specifi-

cations, remove dial indicator assembly.

8. Install and adjust valve mechanism as outlined.

Removal

1.
Remove valve lifters as outlined.

2.
Remove crankshaft front cover as outlined.

3.
Remove grille as outlined in Section 13.

4.
Remove fuel pump push rod as outlined * in Sec-

tion 6M.

5.
Complete camshaft removal as follows:

CAUTION: All camshaft journals are the same

diameter and care must be used in removing

camshaft to avoid damage to bearings.

Remove camshaft sprocket to camshaft bolts then

remove sprocket and timing chain together. Sprocket

is a light fit on camshaft. If sprocket does not come

off easily a light blow on the lower edge of the

sprocket (with a plastic mallet) should dislodge the

sprocket.

Install two 5/16" - 18 x 4" bolts in camshaft bolt

holes then remove camshaft (fig. 27V).

Installation

NOTE: Whenever a new camshaft is installed
CONVERTER

BOLT AREA -

DEPRESSED

SYNCHROMESH
RING

GEAR

TRANS.,

AUTOMATIC

Fig.
28V - Flywheel Installation (Typical)

coat camshaft lobes with Molykote or its

equivalent.

1.
Lubricate camshaft journals with engine oil and in-

stall camshaft.

2.
Install timing chain on camshaft sprocket. Hold the

sprocket vertical with the chain hanging down, and

orient to align marks on camshaft and crankshaft

sprockets. Refer to Figure 20V.

3.
Align dowel in camshaft with dowel in hole in cam-

shaft sprocket then install sprocket on camshaft.

Refer to Figure 25V.

4.
Draw the camshaft sprocket onto camshaft using the

mounting bolts. Torque to specifications.

5.
Lubricate timing chain with engine oil.

6. Install fuel pump push rod as outlined in Section 6M.

7.
Install grille as outlined in Section 13.

8. Install crankcase front cover as outlined.

9. Install valve lifters as outlined.

FLYWHEEL

Removal

With transmission and/or clutch housing and clutch

removed from engine, remove the flywheel.

Installation

1.
Clean the mating surfaces of flywheel and crankshaft

to make certain there are no burrs.

2.
Install flywheel on crankshaft and position to align

dowel hole of crankshaft flange and flywheel (fig.

28V).

NOTE: On Automatic Transmission equipped

engines, the flywheel must be installed with the

flange collar to transmission side (fig. 33V).

ENGINE MOUNTS

Engine mounts (fig. 34V) are the nonr adjustable type

and seldom require service. Broken or deteriorated

mounts should be replaced immediately, because of the

added strain placed on other mounts and drive line

components.

Front Mount Replacement

1.
Remove nut, washer and engine mount through-bolt.

2.
Raise engine to release weight from mount.

3.
Remove mount from engine.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE
6-38

4.
Install new mount on engine.

5. Lower engine, install through-bolt and tighten all

mount bolts to specified torques.

Rear Mount Replacement

1.
Remove crossmember-to-mount bolts.

2.
Raise transmission to release weight from mount.
3.
Remove mount-to-transmission bolts, then remove

mount (and spacer on Chevrolets).

4.
Install new mount (and spacer on Chevrolets) on

transmission.

5. While lowering transmission, align and start cross-

member-to-mount bolts.

6. Lower transmission and tighten all mounting bolts

to specified torques.

CHEVELLE
CHEVY
II

FRONT

REAR
CORVETTE

FRONT

REAR
CAMARO

FRONT

REAR

Fig.
29V -
Engine Mounts

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 6M

ENGINE FUEL

CONTENTS OF THIS SECTION

Page

Carburetors 6M-1 Fuel Pumps .

Air Cleaners 6M-7 Special Tools
Page

6M-10

6M-12

CARBURETORS

INDEX

Page

General Description 6M-1

Service Procedures 6M-1

Preliminary Checks 6M-1

Idle Speed and Mixture Adjustment ........... 6M-1

Fast Idle Adjustment .................. 6M-3

Choke Adjustment 6M-3

Float Adjustment 6M-4
Page

Additional Adjustments 6M-4

Removal 6M-4

Test Before Installation 6M-5

Installation 6M-5

Fuel Filter Maintenance 6M-5

Choke Coil Replacement 6M-5

Throttle Linkage Adjustment . . 6M-6

GENERAL DESCRIPTION

Various carburetors (fig. lc) are used with Chevrolet,

Chevelle, Chevy II, Camaro and Corvette passenger

vehicles. These carburetors are designed to meet the

particular requirements of engines, transmissions and

vehicles, therefore carburetors that look alike are not

always interchangeable. (Refer to carburetor part num-

ber and/or specifications.)

Because many service procedures for the various

carburetors are similar, typical illustrations and pro-

cedures are used except where specific illustrations or
procedures are necessary to clarify the operation.

This section covers removal, installation and adjust-

ments (on engine) of carburetors. Also covered in this

section are maintenance procedures for choke coils,

throttle linkage and fuel filters. For carburetor .over-

haul procedures and additional adjustments (bench), re-

fer to Section 6M of the Overhaul Manual under the

carburetor being serviced.

Specifications for carburetors are located in the back

of this manual.

SERVICE PROCEDURES

Preliminary Checks

1.
Thoroughly warm-up engine. If the engine is cold,

allow to run for at least 15 minutes.

2.
Inspect torque of carburetor to intake manifold bolts

and intake manifold to cylinder head bolts to exclude

the possibility of air leaks.

3.
Inspect manifold heat control valve (if used) for free-

dom of action and correct spring tension.

Idle Speed and Mixture Adjustment (Except Air Injection

Reactor System)

NOTE:
This adjustment should be performed

with engine at operating temperature and park-

ing brake applied.

1.
Remove Air Cleaner.

2.
Connect tachometer and vacuum gauge to engine, then

set hand brake and shift transmission into neutral.

3.
As a preliminary adjustment, turn idle mixture

screws lightly to seat and back out 1-1/2 turns.

CAUTION: Do not turn idle mixture screw

tightly against seat or damage may result.

4.
With engine running (choke wide open) adjust idle
speed screw to specified idle speed, (automatic

transmission in drive, synchronized transmission in

neutral).

5. Adjust idle mixture screw to obtain highest steady

vacuum at specified idle speed.

NOTE:
On air conditioned vehicles, turn air

conditioning to the "on" position and hold the

hot idle compensator valve closed while adjust-

ing idle speed and idle mixture screws.

NOTE:
On Rochester BV carburetors the idle

mixture screw should be turned out 1/4 turn

from the "lean roll" position. The definition

of "lean roll" point is a 20 to 30 rpm drop

in engine speed obtained by leaning the idle

mixture.

6. Repeat Steps 4 and5 as needed for final adjustment.

NOTE:
If necessary, final adjustment of the \

carburetor may be made with the air cleaner

installed.

7. Turn engine off, remove gauges and install air

clearer.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE FUEL 6M-3

Idle Speed and Mixture Adjustment (With Air Injection

Reactor System)

The following is the recommended procedure for Air

Injection Reactor System equipped engines.

NOTE: This adjustment should be performed

with engine at operating temperature and parking

brake applied.

1.
Remove air cleaner.

2.
Connect tachometer to engine, then set hand brake

and shift transmission into neutral.

3.
As a preliminary adjustment, turn idle mixture

screws lightly to seat and back out 3 turns.

CAUTION: Do not turn idle mixture screw

tightly against seat or damage may result."

4.
With engine running (choke wide open) adjust idle

speed screw to specified idle speed. (Automatic

transmission in dirve, synchronized transmission in

neutral).

5.
Adjust idle mixture screw (turn in) to "lean roll"

position; then turn screw out 1/4 turn (1/4 turn

rich from "lean roll"). The definition of "lean

roll" point is a 20 to 30 rpm drop in engine speed,

obtained by leaning the idle mixture.

NOTE: On air conditioned vehicles, turn air

conditioning "OFF" on in-line, 283, 327, and'

350 cu. in. engines, and turned "ON" and hot

idle compensator held closed on 396 and 427 cu.

in. engines.

6. Repeat Steps 4 and 5 as needed for final adjustment.

NOTE: If necessary, final adjustment of the
carburetor may be made with air cleaner

installed.

7.
Shut down the engine, remove gauges and install air

cleaner. *

Fast Idle Adjustment

Rochester
4MV and Holley

With fast idle lever on high step of cam and choke valve

open (engine warm) set fast idle to give specified engine

rpm. Adjust sejrew on Rochester 4MV and bend fast

idle lever *pn Holley. .

Choke Adjustment

With Remote Choke (Fig. 2c)

1.
Remove air cleaner and check to see that choke

valve and rod move freely.

2.
Disconnect choke rod at choke lever.

3.
Check choke adjustment as follows:

On all except 275 and 300 h.p. 327 cu. in. engines,

hold choke valve closed and pull.rod up against stop.

The top of choke rod end should be 1/2-1 rod diame-

ter above top of hole in choke valve lever.

On 275 and 300 h.p. 327 cu. in. engines, hold choke

valve closed and push rod down against stop on ther-

mostat bracket. The top of the choke rod should be

1/2-1 rod diameter below the top of the hole in the

choke lever.

4.
If necessary, adjust rod length by bending rod at

offset bend. (Bend must be such that rod enters

choke lever hole freely and squarely).

5.
Connect rod at choke lever and install air cleaner.

With Manual Choke (Carter YF)

1.
Remove air cleaner.

CHOKE VALVE

COMPLETELY

CLOSED

PULL UPWARD ON

ROD TO END OF

TRAVEL

BEND ROD

TO ADJUST
ROD IN BOTTOM

OF SLOT

BOTTOM OF

ROD SHOULD

BE EVEN WITH

TOP OF

HOLE
CHOKE VALVE

CLOSED

BOTTOM OF

ROD SHOULD

BE EVEN WITH

TOP OF HOLE

TOP OF ROD

SHOULD BE EVEN

WITH BOTTOM

OF HOLE (CHOKE

CLOSED)

BEND ROD TO

ADJUST

PULL DOWNWARD'

ON ROD TO CON-

TACT STOP

L6 (TYPICAL)

[

V8 327-275 HP

V8 350-295 HP
BEND ROD

TO ADJUST

PULL UPWARD ON

ROD TO CONTACT

STOP ON BRACKET

ALL V8 (EXCEPT 327-275 HP

AND 350-295 HP)

Fig.
2C—Remote Choke Adjustment

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE FUEL 6M-4

Fig.
3C-Fuel Level Sight Plug

2.
Push hand choke knob in to within 1/8" of instru-

ment panel.

3.
Loosen choke cable clamp at carburetor bracket and

adjust cable through the clip until the choke valve

is wide open.

4.
Tighten cable clamp at carburetor bracket and check

operation of choke valve to ensure full closed and

wide open positions.

5. Install air cleaner.

Float Adjustment

Ho/fey (Model 4150
Center
Inlet & Model 2300)

1.
Remove air cleaner then remove the fuel level sight

plugs (Fig. 3c)

2.
With parking brake on, and transmission in neutral,

start the engine and allow it to idle.

3.
With the car on a level surface, the fuel level should

be on a level with the threads at the bottom of the

sight plug port (plus or minus 1/32 inch).

NOTE:
No float drop adjustment is required

on this carburetor.

4.
If necessary to adjust (either or both bowls), loosen

inlet needle lock screw and turn the adjusting nut

clockwise to lower or counter-clockwise to raise

fuel level, then tighten lock screw.

NOTE:
1/6 turn of adjusting nut equals ap-

proximately 1/16" fuel level change.

5. Allow a minute for fuel level to stabilize then re-

check the level at sight plug.

6. Readjust, if necessary, until proper level is obtained,

then install sight plug and air cleaner.

NOTE:
To assure proper secondary float level

setting it is advisable to accelerate primary

throttles slightly and hand operate secondary
throttle. This assures a stabilized secondary

fuel level.

Additional Adjustments

The following adjustments may be made without re-

moving the carburetor from the engine. For procedure

refer to Section 6M of the Overhaul Manual under the

carburetor being serviced.

Rochester BV

• Float

• Idle Vent

• Choke Rod (Fast Idle)

• Choke Vacuum Break

• Choke Unloader

Rochester 2GV

• Float

• Accelerator Pump

• Idle Vent

• Choke Rod (Fast Idle)

• Choke Vacuum Break

• Choke Unloader

• Secondary Throttle Opening

• Secondary Throttle Lockout

Rochester 4MV

• Float

• Accelerator Pumj)

• Idle Vent

• Air Valve

• Choke Rod

• Choke Vacuum Break

• Choke Unloader

• Air Valve Lockout

• Secondary Opening

• Secondary Lockout

Carter YF

• Float

• Idle Vent

• Choke Rod (Fast Idle)

• Choke Vacuum Break

• Choke Unloader

Holley 4160 and 4150
(Except End
Inlet)

• Float

• Air Vent Valve

• Accelerator Pump

• Choke Vacuum Break

• Choke Unloader

Holley 2300 and 4150
(End
Inlet)

• Air Vent Valve (except 2300)

• Accelerator Pump

• Choke Vacuum Break

• Choke Unloader

Removal

Flooding, stumble on acceleration and other perform-

mance complaints are, in many instances, caused by the

presence of dirt, water, or other foreign matter in the

carburetor. To aid in diagnosing the cause of the com-

plaint, the carburetor should be carefully removed from

the engine without draining the fuel from the bowl.

The contents of the fuel bowl may then be examined for

contamination as the carburetor is disassembled.

1.
Remove air cleaner and gasket.

2.
Disconnect fuel and vacuum lines from carburetor.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE FUEL 6M-5

3.
Disconnect choke rod or choke cable.

4.
Disconnect accelerator linkage.

5.
If equipped with Automatic transmission, discon-

nect TV linkage.

6. Remove carburetor attaching nuts and/or bolts and

remove carburetor.

Test Before Installation -

It is good shop practice to fill the carburetor bowl

before installing the carburetor. This reduces the strain

on the starting motor and battery and reduces the pos-

sibility of backfiring while attempting to start the engine.

A fuel pump clamped to the bench, a small supply of fuel

and the necessary fittings enable the carburetor to be

filled1 and the operation of the float and'intake needle and

seat to be checked. Operate the throttle several times

and check the discharge from the pump jets before in-

stalling the carburetor.

Installation

1.
Be certain throttle body and intake manifold sealing

surfaces are clean.

2.
Install new carburetor to manifold flange gasket (if

required).

3.
Install carburetor over manifold studs.

4.
Start vacuum and fuel lines at carburetor.

5.
Install attaching nuts and/or bolts and tighten

securely.

6. Tighten fuel and vacuum lines.

7.
Connect and adjust accelerator and TV linkage.

8. Connect choke tube or choke rod.

9. Adjust idle speed and mixture, then install air

cleaner. #

Fuel Filter Maintenance

1.
Disconnect fuel line connection at inlet fuel filter

nut.

2.
Remove inlet fuel filter nut from carburetor with a

1"
box wrench or socket.

3.
Remove filter element and spring (fig. 4c).
Fig. 5C-Choke Coil-L6 Engine

4.

Fig. 4C-Fuel Filter
Check element for restriction by blowing on cone

end, element should allow air to pass freely.

5.
Clean element by washing in solvent and blowing out.

Blow in opposite direction of fuel flow.

NOTE: Element should be replaced if plugged

or if flooding ocpurs. A plugged filter will

result in a loss of engine power or rough (pul-

sating) engine feel, especially at high engine

speeds.

6. Install element spring, then install element in car-

buretor so small section of cone faces out.

7.
Install new gasket on inlet fitting nut then install

nut in carburetor and tighten securely.

8. Install fuel line and tighten connector.

Choke Coil Replacement

L6 Engines (Fig. 5c)

1.
Remove air cleaner then disconnect choke rod upper

clip.

2.
Remove bolts attaching choke coil to manifold, then

remove choke coil and choke rod as an assembly.

3.
Disconnect choke rod from choke coil.

4.
Connect choke rod to new choke coil and install as-

sembly on manifold.

5.
Install bolts and tighten securely.

6. Adjust and connect choke rod as outlined.

7.
Start and warm-up the engine then check operation

of choke and install air cleaner.

V8 Engines (Fig. 6c)

1.
Remove air cleaner then disconnect choke rod upper

clip.

2.
Remove choke coil as follows:

WITH ROCHESTER 2GV CARBURETOR

• Remove the choke coil shield by prying with a

screw driver in the cut out provided then re-

move the choke rod.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE FUEL 6M-6

Fig.
6C-Choke Coil-V8 Engine

• Remove bracket and choke coil assembly.

WITH ROCHESTER 4MV AND

HOLLEY CARBURETORS

• Remove the choke coil shield by prying with a

screw driver in the cut out provided then lift

shield carefully over rod.

• Remove choke rod, bracket screw and choke

coil assembly
3.
Install a new choke coil assembly being sure the

locating tab is in the forward hole of the intake

manifold then install mounting screw.

4.
Complete installation as follows:

WITH ROCHESTER 2GV CARBURETOR

• Check that the choke rod eye of the coil is

below the stop tab on the bracket then install

the choke
ro and adjust if necessary.

• Install the choke coil shield over the choke coil

and move shield to best fit along manifold.

WITH ROCHESTER 4MV AND

HOLLEY CARBURETORS

• Install the choke rod and adjust as necessary

(without choke coil shield installed).

• Disconnect choke rod upper end and lower choke

coil shield over choke rod and install over choke

coil.

• Move shield to best fit along manifold and con-

nect upper end of choke rod.

5. Be sure choke valve moves freely from full open

to full closed position.

6. Start and warm up the engine and check operation

of the choke.

7. Install the air cleaner.

Throttle Linkage Adjustment (Fig. 7c or 8c)

1.
Disconnect throttle rod swivel at throttle lever on

carburetor.

2.
On automatic transmission equipped vehicles dis-

connect TV rod at throttle lever.

3.
Hold carburetor throttle in wide open position, push

throttle rod rearward (to position accelerator pedal

at the floor mat) and adjust swivel to just enter hole

in throttle lever.

4.
Connect swivel to throttle lever and install accelera-

tor return spring.

CAMARO & CHEVY II V8

CHEVELLE & CHEVROLET

V8

CAMARO
&
CHEVY
II

V8

CHEVELLE &

CHEVROLET V8
ALL SERIES

IN LINE

ALL SERIES

INLINE

Fig.
7C—Throttle Linkage—Chevrolet, Chevelle, Chevy II and Camaro

CHEVROLET CHASSIS SERVICE MANUAL