1967 CHEVROLET CAMARO heater

HEATER AND AIR CONDITIONING 1A-23

DEFROSTER

RECEIVER

DEHYDRATOR

EVAPORATOR

Fig.
33—All Weather System Components (Chevy II)

DEFROSTER OUTLETS
OUTSIDE
AIR
FROM PLENUM DUCT

BLOWER
--—-.

DEFROSTER

DOOR

HEATER OUTLET

AIR CONDITIONER "ON" DOOR

EVAPORATOR CORE

COLD
HEATER

CORE

AIR CONDITIONER

OUTLETS

AIR CONDITIONING

CONTROLS

AIR CONDITIONING

"ON"
KNOB
\ AIR DOOR

^CIRCULATED

m

AIR-FAN KNOB-

HEAT KNOB
HEAT DOOR

AIR

HEATER CONTROLS

IMJLJLII
""" L

—Mwm \

' / DASH PANEl

KNOB
DEFROSTER KNOB

Fig.
34-AH Weather System Schematic

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR. CONDITIONING 1A-24

Fig. 35-Controls-AII Weather (Chevy II)

The heater components of the system are similar to

the standard Corvette heater with hoses routing engine

coolant to and from the heater core. A vacuum operated

shutoff valve assures that no coolant will pass through

the heater core until the system calls for heat.

Four control knobs surrounding the clock on the in-

strument panel center console provide full control of the

heating and cooling functions of the air conditioning

system.
The general arrangement of the system components

is pictured in Figure 37 while a schematic view of the

system will be found in Figure 36.

Controls Corvette

Four control knobs, grouped around the clock on the

instrument panel central console, provide full control

of the heating and cooling functions of the Corvette Air

Conditioning System. Each of the knobs, through a bowden

cable, operates one of the air diverter doors in the air

distributor assembly. In addition, the AIR COND.-PULL

knob operates the compressor switch; blower speeds are

controlled by turning the AIR PULL knob; and the heater

hot water valve vacuum switch is actuated by the COOL

IN-HQT PULL knob.

Air Conditioning "ON" Knob

The "AIR COND. PULL" knob controls the positioning

of the air diverter door which routes conditioned air

through either the dash diffuser ducts or the floor dis-

tributor outlets. Movement of this knob (hence, movement

of the selector door) also controls' the compressor

switch. When the door is positioned to send air through

the dash outlets the compressor is automatically turned

on to place the cooling system in operation and the fan

is turned on to LOW speed.

Blower Switch and Air Selector

The AIR PULL-FAN knob operates the selector door

in the right hand plenum chamber and may be set to allow

full outside air, full inside air, or a mixture of the two to

DEFROSTER DOOR

OPERATED BY

DEFROSTER KNOB
AIR CONDITIONING DOOR

OPERATED BY

AIR COND. PULL KNOB
BLOWER

OPERATED

BY TURNING

AIR KNOB

AIR DOOR

OPERATED

BY PULLING

AIR KNOB

OUTSIDE

AIR

CONTROLS

HEAT DOOR

OPERATED BY

COOL IN-HOT PULL

KNOB

L.H. OUTLET
CENTER

OUTLET
R.H. OUTLET
AIR COND.

PULL
COOL IN

HOT PULL

AIR PULL

LO-MED-HI
DEFROSTER

PULL

Fig.
36—Corvette Four-Season System Schematic

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-25

Fig.
37—-Corvette Four-Season System Components

pass through the system. For heating operations it is

suggested that Ml outside air (knob Mly OUT) be used.

For cooling operations under extreme heat conditions

push knob fully in (recirculated inside air); under moder-

ate temperature conditions pull the knob out to the detent

position (a misxture of outside air and inside air); and

under mild temperature conditions the knob may be

pulled fully out (outside air).

After the AIR PULL knob is set to permit air to pass

through the system, the knob may be rotated to control

the three-speed blower. When the AIR COND.-PULL

knob is pulled out the low blower is in operation. Select

higher speeds as desired.

Temperature Adjustment

The COOL IN-HOT PULL knob controls the air output

temperature during both heating and cooling operations.

A vacuum switch (operated by the temperature door

actuating cam) controls a vacuum operated water valve

which allows engine coolant to flow through the heater

core only when this knob is pulled out.

During heating operation cold ambient air enters the

conditioner, passes through the inoperative cooling core

and then passes through and around the heating core

(the final mixture of hot and cold air being determined

by the control knob - temperature door setting) and then

enters the car.

Cooling operation is exactly the same except that the

cooling core (evaporator) will be in operation at Ml

capacity, removing as much heat and humidity as pos-
sible from the warm ambient air flowing through it.

The COOL IN-HOT PULL knob may then be pulled out

as needed to temper this maximum cold airflow should

it become necessary.

Defroster Control

This control acts to divert heated air from the floor

distributor duct into the defroster duct for windshield

defogging, defrosting and deicing operations. A detent

is built into the defroster linkage to indicate the setting

at which a small portion of the heater air will be con-

tinaully passed over the windshield, thus keeping it clear.

Operating Instructions

Remember that the air conditioning system may be

used for heating or cooling during any season of the

year to provide just the desired comfort conditions.

Cooling

1.
"Air Cond-Pull". This knob should be pulled fully

out.

2.
"Cool In-Hot Pull". This knob should be pushed

fully in for maTriTr»"Tn cooling. Pulling out the knob

as required will mix warm air with the cool air to

temper the cool air output.

3.
"Air Pull-Fan". Set this knob fully in during ex-

treme heat conditions; at the detent position during

moderate temperature conditions; fully out during

mild temperature conditions or whenever tempering

of the cooled air flow is necessary. Turn the knob

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-26

clockwise for medium and high blower speed, as

desired. Low blower speed is automatic during

cooling operations.

4.
"Def-Pull". This knob should be pushed fully in.

Additional Cooling Hints

1.
The center barrel outlet in the dash may be rotated

to deflect air as desired or used to act as a shut off

door.

2.
The right and left ball outlets may be rotated to

deflect air in the direction desired. Each outlet has

a shut off valve operated by a knob approximately

4 in. inboard. When the knob is horizontal, the valve

is open.

3.
There are two (2) additional outlets in the bottom of

the ducts approximately 6" inboard from the valve

knobs. A rotating cover will open these outlets to

provide cool air for the feet if desired.

4.
When first entering a very warm car, open the

windows for a few minutes until the interior of the

car has cooled off.
Heating

1.
"Air Pull-Fan". Pull this knob fully out. Rotate

the knob clockwise for low, medium or high blower

speed as desired. If just a small amount of heat is

desired, leave the fan on low or medium speed and

regulate the temperature with the "Cool In-Hot Pull"

knob.

2.
"Air Cond-Pull". This knob should normally be

pushed fully in. However, during cool, damp days

it is possible, by pulling this knob fully out, to de-

humidify the air by passing it through the evaporator

core before reheating to the desired outlet

temperature.

3.
"Cool In-Hot Pull". Pull this knob out as far as

necessary to provide the temperature desired.

4.
"Def-Pull". Pull this knob all the way out for

maximum defrosting or de-icing. When the knob is

partly out, a portion of the hot air is used for de-

frosting and the balance is discharged through the

heater outlet.

GENERAL INFORMATION

In any vocation or trade, there are established proce-

dures and practices that have been developed after many

years of experience. In addition, occupational hazards

may be present that require the observation of certain

precautions or use of special tools and equipment. Ob-

serving the procedures, practices and precautions of

servicing refrigeration equipment will greatly reduce the

possibilities of damage to the customers' equipment as

well as virtually eliminate the element of hazard to the

serviceman.

PRECAUTIONS IN HANDLING REFRIGERANT-12

Refrigerant-12 is transparent and colorless in both the

gaseous and liquid state. It has a boiling point of 21.7^

below zero and, therefore, at all normal temperatures

and pressures it will be a vapor. The vapor is heavier

than air and is noninflammable, nonexplosive, non-

poisonous (except when in contact with an open flame)

and noncorrosive (except when in contact with water).

The following precautions in handling R-12 should be

observed at all times.

• All refrigerant drums are shipped with a heavy metal

screw cap. The purpose of the cap is to protect the

valve and safety plug from damage. It is good .prac-

tice to replace the cap after each use of the drum.

• If it is ever necessary to transport or carry a drum

or can of refrigerant in a car, keep it in the luggage

compartment. Refrigerant should not be exposed to

the radiant heat from the sun for the resulting in-

crease in pressure may cause the safety plug to

release or the drum or can to burst..

• Drums or disposable cans should never be subjected

to high temperature when adding refrigerant to the

system. In most instances, heating the drum or can

is required to raise the pressure in the container

higher than the pressure in the system during the

operation. It would be unwise to place the drum on a

gas stove, radiator or use a blow torch while pre-

paring for the charging operation, for a serious ac-

cident can result. Don't depend on the safety
plug - many drums have burst when the safety plug

failed.' Remember, high pressure means that great

forces are being exerted against the walls of the

container. A bucket of warm water, not over 125°F,

or warm wet rags around the container is all the heat

that is required.

• Do not weld or steam clean on or near the system.

Welding or steam cleaning can result in a dangerous

pressure buildup in the system.

• When filling a small drum from a large one, never

fill the drum completely. Space should always be

allowed above the liquid for expansion. If the drum

were completely full and the temperature was in-

creased, hydraulic pressure with its tremendous

force would result.

• Discharging large quantities of R-12 into a room can

usually be done safely as the vapor would produce

no ill effects, however, in the event of an accidental

rapid discharge of the system it is recommended

that inhalation of large quantities of R-12 be avoided.

This caution is especially important if the area con-

tains a flame producing device such as a gas heater.

While R-12 normally is nonpoisonous, heavy con-

centrations.. of it in contact with a live flame will

produce a toxic gas. The same gas will also attack

all bright metal surfaces.

• Protection of the eyes is of vital importance! When

working around a refrigerating system, an accident

may cause liquid refrigerant to hit the face. If the

eyes are protected with goggles or glasses, no

serious damage can result. Just remember, any

R-12 liquid that you can touch or that touches you is

at least 21.7"F. below zero. The eyeballs can't take

much of this temperature. If R-12 liquid should

strike the eyeballs, here is what to do:

1.
Keep calm.

2.
Do not rub the eyes! Splash the affected area with

quantities of cold water to gradually get the tem-

perature above the freezing point. The use of min-

eral, cod liver or an antiseptic oil is important in

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-27

POA SUCTION

THROTTLING
RTJING
^EXTERNAL

EQUALIZER LINE

COMPRESSOR

(Operates

continually

while system

is in operation)

M
H. P.
VAPOR
OIL BLEED LINE

SIGHT
,n

RECEIVERS

DEHYDRATOR

/

CONDENSER

EVAPORATOR

H.
P.
LIQUID
H
L. P.
LIQUID H] L.
P.
VAPOR
@ H. P.
POWER ELEMENT

III
•••••Mi
IM •—>•••—^

Fig.
38—Cycle
of
Operation—Four-Season and Comfortron

LINE
TO
COMPRESSOR

CLUTCH
THERMOSTATIC

SWITCH
v
CAPILLARY

* TUBING

EXPANSION

VALVE

SIGHT

GLASS

COMPRESSOR

(Operation

controlled

by thermostatic

switch)

I
H. P.
VAPOR

1
H. P.
LIQUID
aiJJ>1Tg.VW
RECEIVER

DEHYDRATOR

CONDENSER

EVAPORATOR

AVPSty>t*i"^if^

L.
P.
LIQUID

L.
P.
VAPOR
H.
P.
VAPOR POWER ELEMENT

Fig.
39-Cyc!e
of
Operation—Universal and All Weather

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-28

providing a protective film to reduce the possibility

of infection.

3.
As soon as possible, call or consult an eye specialist

for immediate and future treatment.

REMEMBER -

pound of cure."
"An ounce of prevention is worth a

PRECAUTIONS IN HANDLING REFRIGERANT LINES

• All metal tubing lines should be free of kinks, be-

cause of the restriction that kinks will offer to the

flow of refrigerant. The refrigeration capacity of the

entire system can be greatly reduced by a single

kink.

• The flexible hose lines should never be bent to a

radius of less than 10 times the diameter of the hose.

• The flexible hose lines should never be allowed to

come within a distance of 2-1/2" of the exhaust

manifold.

• Flexible hose lines should be inspected at least once

a year for leaks or brittleness. If found brittle or

leaking they should be replaced with new lines.

• Use only sealed lines from parts stock.

• When disconnecting any fitting in the refrigeration

system, the system must first be discharged of all

refrigerant. However, proceed very cautiously re-

gardless of gauge readings. Open very slowly, keep-

ing face and hands away so that no injury can occur

if there happens to be liquid refrigerant in the line.

If pressure is noticed when fitting is loosened, allow

it to bleed off very slowly.

CAUTION: Always wear safety goggles when

opening refrigerant lines.

• In the event any line is opened to atmosphere, it

should be immediately capped to prevent entrance

of moisture and dirt.

• The use of the proper wrenches when making con-

nections on "O" ring fittings is important. The use

of improper wrenches may damage the connection.

The opposing fitting should always be backed up with

a wrench to prevent distortion of connecting lines or

components. When connecting the flexible hose con-

nections it is important that the swagged fitting and

the flare nut, as well as the coupling to which it is

attached, be held at the same time using three dif-

ferent wrenches to prevent turning the fitting and

damaging the ground seat.

• "O" rings and seats must be in perfect condition.

The slightest burr or piece of dirt may cause a leak.

• Sealing beads on hose clamp connections must be

free of nicks and scratches to assure a perfect seal.

MAINTAINING CHEMICAL STABILITY IN THE

REFRIGERATION SYSTEM

The metal internal parts of the Chevrolet refrigeration

system and the refrigerant and oil contained in the sys-

tem are designed to remain in a state of chemical

stability as long as pure R-12 and uncontaminated re-

frigeration oil is used in the system.

However, when abnormal amounts of foreign materials,

such as dirt, air or moisture are allowed to enter the

system, the chemical stability may be upset. When ac-

celerated by heat, these contaminates may form acids
Fig.
40-^-System Contaminants

and sludge and eventually cause the breakdown of com-

ponents within, the system. In addition, contaminates may

affect the temperature-pressure relationship of R-12,

resulting in improper operating temperature and pres-

sures and decreased efficiency of the system.

The following general practices should be observed to

insure chemical stability in the system.

• Whenever it becomes necessary to disconnect a

refrigerant or gauge line, it should be immediately

capped. Capping the tubing will also prevent dirt and

foreign matter from entering.

• Tools should be kept clean and dry. This also in-

cludes the gauge set and replacement parts.

• When adding oil, the container should be exception-

ally clean and dry due to the fact that the refrigera-

tion oil in the container is as moisture-free as it is

possible to make it. Therefore, it will quickly absorb

any moisture with which it comes in contact. For

. this same reason the oil container should not be

opened until ready for use and then it should be

capped immediately after use.

• When it is necessary to open a system, have every-

thing you will need ready and handy so that as little

Fig.
41—Gauge Set

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-29

time as possible will be required to perform the

operation. Don't leave the system open any longer

than is necessary.

• Finally, after the operation has been completed and

the system sealed again, air and moisture should be

evacuated from the system before recharging.

GAUGE SET

The gauge set (fig. 41) is used when purging, evacua-

ting, charging or diagnosing trouble in the system. The

gauge at the left is known as the low pressure gauge.

The face is graduated into pounds of pressure and, in

the opposite direction, in inches of vacuum. This is the

gauge that should always be used in checking pressures

on the low pressure side of the system. When all parts of

the system are functioning properly the refrigerant

pressure on the low pressure side never fails below 0

pounds pressure. However, several abnormal conditions

can occur that will cause the low pressure to fall into a

partial vacuum. Therefore, a low pressure gauge is

required.

The high pressure gauge is used for checking pres-

sures on the high pressure side of the system.

The connection at the left is for attaching the low

pressure gauge line and the one at the right the high

pressure gauge line. The center connector is common to

both and is for the purpose of attaching a line for adding

refrigerant, discharging refrigerant, evacuating the sys-

tem and other uses. When not required, this line or

connection should be capped.

NOTE:
Gauge fitting connections should be in-

stalled hand tight only and the connections leak

tested before proceeding.

The hand shutoff valves on the gauge manifold do not

control the opening or closing off of pressure to the

gauges. They merely close each opening to the center

connector and to each other. During most diagnosing

and service operation, the valves must be closed. The

only occasion for opening both at the same time would be

to bypass refrigerant vapor from the high pressure to

the low pressure side of the system, or in evacuating

both sides of the system.

CHARGING STATION

The J-8393 Charging Station is a portable assembly of

a vacuum pump, refrigerant supply, gauges, valves, and

most important, a five (5) pound metering refrigerant

charging cylinder. The use of a charging ey'inder elim-

inates the need for scales, hot water pails, etc.

The chief advantage of this unit is savings. A very

definite savings in refrigerant and time can be obtained

by using this unit. Since the refrigerant is metered into

the system by volume, the correct amount may be added

to.
the system and charged to the customer. This, coupled

with the fact that the unit remains "plumbed" at all times

and thus eliminates loss of refrigerant in purging of

lines and hooking-up, combines to enable the operator to

get full use of all refrigerant purchased by the

dealership.

All evacuation and charging equipment is hooked to-

gether in a compact portable unit (fig. 42) which brings

air conditioning service down to the basic problem of

hooking on two hoses, and manipulating clearly labeled

valves.
Fig.
42—System Charging Station

This will tend to insure that the job will be done without

skipping operations. As a result, you can expect to save

time and get higher quality work, less chance of an over

or undercharge, or comeback.

The pump mount is such that the dealer may use his

own vacuum pump. The gauges and manifold are in com-

mon use. Thus a current air conditioning dealer can use

the equipment on hand and avoid duplication.

LEAK TESTING THE SYSTEM

Whenever a refrigerant leak is suspected in the system

or a service operation performed which results in dis-

turbing lines or connections, it is advisable to test for

leaks.
Common sense should be the governing factor in

performing any leak test, since the necessity and extent

of any such test will, in general, depend upon the nature

of the complaint and the type of service performed on

the system. It is better to test and be sure, if in doubt,

than to risk the possibility of having to do the job over

again.

NOTE:
The use of a leak detecting dye within

the system is not recommended because of the

following reasons:

1.
Refrigerant leakage can exist without any oil leakage.

In this case the dye will not indicate the leak, how-

ever, a torch detector will.

2.
The addition of additives, other than inhibitors, may

alter the stability of the refrigeration system and

cause malfunctions.

3.
Dye type leak detectors which are insoluble form a

curdle which can block the inlet screen of the ex-

pansion valve.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-30

Leak Detector

Tool J-6084 (fig. 43) is a propane gas-burning torch

which is used to locate a leak in any part of the system.

Refrigerant gas drawn into the sampling tube attached to

the torch will cause the torch flame to change color in

proportion to the size of the leak. Propane gas fuel

cylinders used with the torch are readily available

commercially throughout the country.

CAUTION: Do not use lighted detector in any

place where combustible or explosive gases,

dusts or vapors may be present;

Operating Detector

1.
Open control valve only until a low hiss of gas is

heard, then light gas at opening in chimney.

2.
Adjust flame until desired volume is obtained. This

is most satisfactory when blue flame is approxi-

mately 3/8" above reactor plate. The reaction plate

will quickly heat to a cherry red.

3.
Explore for leaks by moving the end of the sampling

hose around possible leak points in the system. Do

not pinch or kink hose.

NOTE: Since R-12 is heavier than air, it is

good practice to place open end of sampling tube

immediately below point being tested, partic-

ularly in cases of small leaks.

CAUTION: Do not breathe the fumes that are

produced by the burning of R-12 gas in the de-

tector flame, since such fumes can be toxic in

large concentrations of R?»12.

4.
Watch for color changes. The color of the flame

which passes through the reaction plate will change

to yellow when sampling hose draws in very small

CHIMNEY

REACTION PLATE

BURNER HEAD

Fig.
43—Leak Detector
leaks of R-12. Large leaks will be indicated by a

change in color to a vivid purplish-blue. When the

sampling hose passes the leak, the flame will clear

to an almost colorless pale-blue again. If the flame

remains yellow when unit is removed from leak,

insufficient air is being drawn in or the reaction

plate is dirty.

NOTE: A refrigerant leak in the high pressure

side of the system may be more easily detected

when, if possible, the system is in operation. A

leak on the low pressure side may be most

easily detected after the engine has been shut

off for several minutes to allow system pres-

sures to equalize. This particularly applies to

the front seal.

VACUUM PUMP

A vacuum pump should be used for evacuating air and

moisture from the air conditioning system.

Vacuum pump, Tool J-5428, (fig.. 44) is available for

this purpose. It is used as a component part of the

Charging Station J-8393, described previously. The fol-

lowing precautions should be observed relative to tbe

operation and maintenance of this pump.

' • Make sure dust cap on discharge outlet of vacuum

pump is removed before operating.

• Keep all openings capped when not in use to avoid

moisture being drawn into the system.

• Oil should be changed after every 250 hours of nor-

mal operation.

To change oil, simply unscrew hex nut located on

back side of pump, tilt backward and drain out oil

(fig. 44). Recharge with 8 ounces of vacuum pump

oil.
If you desire to flush out the pump, use this

same type clean oil. Do not use solvent.

NOTE: Improper lubrication will shorten the

life of pump.

• If this pump is subjected to extreme or prolonged

cold, allow it to remain indoors until oil has reached

approximate room temperature. Failure to warm oil

will result in a blown fuse.

• A five ampere time delay cartridge fuse has been

installed in the common line to protect the windings

of the compressor. The fuse will blow if an ex-

cessive load is placed on the pump. In the event the

fuse is blown, replace with a five ampere time delay

fuse - do not use a substitute fuse as it will result in

damage to the starting windings.

• If the pump is being utilized to evacuate a burnt-out

system, a filter must be connected to the intake

fitting to prevent any sludge from contaminating the

working parts, which will result in malfunction of the

pump.

• Do not use the vacuum pump as an air compressor.

AVAILABILITY OF REFRIGERANT-12

Refrigerant-12 is available through Parts Stock in 25

lb.
drums and in 15 oz. disposable cans. Valves are

available for
the"
disposable cans, which may be used as

individual cans or as a group of up to four cans (fig. 45).

Tool J-6272 is used with one through four cans. The

use of the four-can fixture makes it possible to charge

the system with a known quantity of refrigerant without

CHEVROLET CHASSIS SERVICE MANUAL