1967 CHEVROLET CAMARO door lock

CORVETTE BODY 1B-T9

Fig.
43—Removing Regulator Assembly

REAR QUARTER

DOOR SILL PLATE AND MOLDING

Figure 49 shows assembly details of both the door sill

plate and molding. The sill plate which retains the car-*

pet, the cowl trim windlace and lock pillar front edge

trim are retained to the body by six screws.

The molding assembly, which replaces a rocker panel,

is quickly and easily replaced by removing 10 retaining

screws. The sill molding retainer is also fastened to the

body with screws.

REAR END

FOLDING TOP COMPARTMENT LID

Adjustments

Hinges

The folding top compartment lid should be adjusted so

that in the closed position the surface of the lid is flush

with surrounding body surfaces and space between lid

edge and body is 1/16" to 3/16" at sides and 3/16" to

1/4" at rear. Whenever lid position is changed on hinges,

lock engagement must be inspected and adjusted if neces-

sary. Adjust hinge position as follows:

1.
Scribe a line on lid surface following contour of hinge

strap.
This will ease observation of lid movement

during adjustment (fig. 51).

2.
To raise or lower top surface of lid, add or remove

hinge shims.

3.
To adjust spacing between lid edges and body, loosen

hinge-to-lid screws and shift lid as required.

Lock

Lock engagement may be adjusted as follows:

1.
Striker plates may be shimmed to adjust the depth

of lock engagement in striker plate. When this ad-

justment is made, release of lock should be tested

and adjusted as required.

2.
Release of lock may be adjusted by loosening lock

assembly retaining bolts and moving lock in ap-

propriate direction to the limit of slotted holes in

, lock base. Further adjustment may be gained by

moving cable retainer in appropriate direction.
Hinges

(Refer to Figure 52)

Removal

1.
Scribe around hinge as shown in Figure 51.

2.
Hinge may be removed as an assembly by opening

top compartment lid fully and removing 3 retaining

screws. Note number of shims found between hinge

frame and compartment floor.

3.
To remove spring from hinge assembly, close top

compartment lid as far as possible and insert Tool

J-9559 between expanded coils in spring. Opening

top compartment lid fully will allow removal of

spring as shown in Figure 53.

4.
As soon as spring is removed, insert long bolt sup-

plied with J-9559 through holes in end of tool, pass-

ing it through spring, and install nut on bolt.

Spring may be removed from J-9559 or J-9559 may be

installed in a new spring, by the following method:

1.
Place a closed 6 or 8 inch "C" clamp in a vise or

fasten it to a heavy bench top (bench should be fas-

tened to floor).

2.
Hook one end of spring in clamp and the other end

in hook of chain hoist, "cherrypicker" or equivalent,

as shown in Figure 54.

3.
Stretch the spring enough to allow insertion of

J-9559. Install through bolt if spring is not to be in-

stalled on hinge at once.

installation

1.
Install same number of shims as removed or, if

repairing collision damage, etc., position hinge in

compartment, install upper mounting screws, fill

gap between floor and hinge frame with shims and

install lower mounting screw.

2.
If spring has been removed from hinge, install

spring in J-9559 and place spring on hinge with com-

partment lid raised; closing lid releases J-9559 for

removal. Upper end of spring should rest in one of

three notches yielding best lid operation. About 3

pounds pressure should be necessary to close lid.

Lock

Removal

1.
Remove cable mounting clamps. Remove retainer

from control cable assembly and disengage cable

from control.

2.
Scribe a mark on lid following outer contour of lock

assembly.

3.
Remove 3 lock assembly retaining screws and re-

move lock from compartment lid.

Installation

1.
Place lock assembly on compartment lid within

scribed line and install retaining screws.

2.
Install end of cable in control assembly and fasten

retainer securely.

3.
Test operation of lock thoroughly, adjusting if neces-

sary as outlined in this section.

Control

Removal

1.
Remove inner mounting clamps from both cables

and disengage cables from control by removing

retainers.

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY
1B-20

DOOR

Fig.
44—Power Window Regulator

2.
Remove
4
mounting screws and remove control from

compartment
lid.

Installation
*

1.
Position control
on
compartment
lid and
install
mounting screws.

2.
Install ends of cables in control and fasten securely

with retainers.

3.
Test operation of locks and adjust if necessary.

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-21

Fig.
45—
Locking Regulator Arm in Place

REAR WINDOW-ADHESIVE CAULKED-

19437 MODEL

For parts identification refer to Figure 55.

1.
Remove the 2 rear window garnish moldings by re-

moving the 14 attaching screws.

2.
Pry molding caps from reveal moldings.

3.
Carefully remove lower, side, and top reveal mold-

ings after marking their position on body with tape.

4.
Secure one end of steel music wire to piece of wood

for handle. Insert other end through caulking mater-

ial at lower corner of rear window; then secure end

of wire to another piece of wood (fig. 56).

5. With the aid of helper, carefully cut through caulking

material (using a sawing motion) with the steel wire;

up side of window, across top, down opposite side,

and across bottom of window.

6. Remove old glass from window opening.

7. Using a sharp scraper or wood chisel, remove ad-

hesive caulking material from body pinchweld flange.

NOTE:
It is not necessary to clean off all the

old caulking material completely from body

opening; however, there should not be any loose

pieces of caulking material left in the opening.

8. Check all reveal molding retaining clips for damage

(24 required). Replace those that are bent or dis-

torted with clips provided in kit.

9. Using weatherstrip adhesive, cement rubber spacers

at bottom, sides, and top of window opening. The

step-type spacers are used at bottom and sides, the

flat type are used at the top, sides, and bottom of

window opening as shown on Figure 55.

10.
Using suction cup holders, position replacement

glass in body opening. Carefully check relationship

of glass to body pinchweld completely around open-

ing. The overlap of glass to body pinchweld and re-

taining flanges should be equal with a minimum over-
lap of 3/16M. Where necessary, position shims under

the lower spacers to obtain required overlap of glass

to body upper and lower flanges.

11.
After proper glass to pinchweld relationship has

been attained, mark position with grease pencil on

glass and body as shown in Figure 57.

12.
Remove glass from body opening and place on pro-

tected surface.

13.
Clean inside edge surface of glass so that glass is

free of any foreign material (oil, grease, etc.).

Using 3/4" masking tape, place tape approximately

1/2 inch from edge of inside surface of glass com-

pletely around glass. Then apply a film of silane

primer to inside edge surface completely around

glass,
also apply silane primer to sealing surface

of pinchweld as shown in Figure 58.

Fig.
46—Door Lock and Remote Controls

1.
Door Lock Remote Control

Assembly

2.
Door Lock Remote Control Knob

3. Door Lock Remote Control Rod
4.
Remote Control Locking Rod

5. Remote Locking Control

Assembly

6. Lock Assembly

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-22

16.

17.

Fig.
47-Door Handle and Lock Cylinder
18.

19.

20.

21.

1.
Screw - Handle Retaining

2.
Reinforcement

3. Gasket - Rear

4.
Handle Assembly

5. Cylinder Assembly - Lock
6. Escutcheon

7.
Retainer

8. Rod - Lock Cylinder

9. Gasket - Front

14.
Cut off painted portion of cartridge nozzle along

edge of paint line.

15.
Mix adhesive caulking material and accelerator

] thoroughly according to directions on container.
NOTE:
Once caulking material is mixed, there

will be approximately 35 minutes of working

time with the material. Subsequent steps should

be performed immediately after caulking ma-

terial is mixed.

Place caulking material in cartridge as shown in

Figure 59.

Carefully apply a smooth continuous bead of caulking

material on inside surface of glass next to edge

completely around glass (fig. 60). Caulking material

should be approximately 1/4 inch wide at the base

and form a pyramid 3/8 inch high. If during appli-

cation the pyramid collapses, wait about 2-3 minutes

for material to set up. If an air bubble is encoun-

tered in material back up the applicator and apply

sufficient material to fill void and to dispense the

bubble before continuing.

The reveal molding clips are self sealing and do

not require sealing before installing the rear glass.

With aid of helper, lift glass and carefully position

glass on spacers, matching up marks on glass and

body as shown in Figure 61.

Press glass lightly to set caulking material to rear

window opening flanges. Paddle material where nec-

essary to insure proper seal.

Watertest rear window immediately using a cold

water spray. If any water leaks are encountered, use

flat bladed screw driver or stick and paddle caulking

material into leak point to correct leak. Correction

of leak is usually more effectively performed by

paddling material from inside the body.

CAUTION: Do not run a heavy stream of water

directly on caulking material while the material

is still soft.

22.

Install the reveal moldings in the following sequence:

Top,
sides, lower and the caps in each upper corner.

23.
Carefully remove masking tape from inside of glass

and install garnish moldings.

Fig.
49—Door Sill Plate and Molding

Fig.
48—Door Hinge
1.
Plate - Door Sill

2.
Retainer - Sill Molding

3. Sill Molding
4.
"U" Nut - Sill Molding Retainer

5. Special Nut

6. Spring Nut - Sill Molding

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-23

Fig.
50—Folding Top Lid Assembly

1.
Striker Shim

2.
Striker

3. Lock Assembly
4. Lid Assembly

5. Control Assembly

6. Weatherstrip Assembly
7. Hinge Shim

8. Hinge Assembly
9. Cable Assembly

10.
Cable Retainer

24.
Clean up excess material with Oleum spirits, prep-

sol or kerosene.

GAS TANK DOOR AND REAR TRIM PLATE

Figure 62 illustrates installation details of gas tank

door and rear trim plate.

Gas tank door and bezel may be replaced by removing

sheet metal screws located on inner circumference of

bezel.

Trim plate is retained by five special nuts which are

accessible from under right rear corner of vehicle.

REAR FILLER PANEL

Removal

1.
Remove rear license plate and license plate housing

as explained in Section 14.
2.
Remove tail pipes from mufflers.

3.
Remove ten screws holding filler panel to body

(fig. 62).

Installation

Reverse removal procedure.

SPARE TIRE MOUNT

Refer to Figure 63.

Removal

1.
Remove spare tire.

2.
Loosen pivot bolt lock nuts and turn pivot bolts out

of weld nuts in crossmember.

3.
Remove two screws retaining swivel bolt assembly

to body.

4.
Remove four bolts holding cover assembly to body.

CHEVROLET CHASSIS SERVICE

CORVETTE BODY 1B-31

1
^JS^ST**-

Fig.
67—Center Body Construction

1.
Panel—Instrument

2.
Pad Assembly Instrument

Panel - Right

Hand

4.
Reinforcement -. Door

Upper Front

5. Panel - Door Inner

Upper
6. Reinforcement - Upper Rear

7. Cover - Front Access Hole

8. Reinforcement - Door Outer

Panel inner

9. Cover - Rear Access Hole

10.
Pillar Assembly - Door Lock

11.
Panel - Door Lower

Inner
12.
Sill - Door

13.
Molding - Rocker

14.
Panel - Side Door

Outer

15.
Panet - Door Hinge

Reinforcing

16.
Reinforcement Assembly

- Side Door Inner
17.
Bonding Strip - Side

Door Upper Bonding

18.
Pillar Panel - Hinge

19.
Hinge Assembly

20.
Pad Assembly Instrument

Panel - Left Hand

21.
Bracket - Radio Mounting

22.
Bracket - Clock Mounting

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-34

1.
Panel - Roof

2.
Door Assembly - Fuel Tank Filler

3. Bezel - Fuel Tank Filler Door

4.
Panel - Body Rear Upper

- Right Hand

5. Panel - Body Rear Upper

- Left Hand

6. Frame - Rear Window Inner

7. Panel - Roof Inner Trim

8. Lid Assembly - Folding Top

Compartment

9. Hinge Assembly - Folding top Lid

- Right Hand

10.
Striker Plate Assembly - Right Hand

11.
Hinge Assembly - Folding Top Lid

- Left Hand

12.
Plate - Nut - Right Hand

13.
Extension - Body Rear Upper Panel
Fig.
70—Rear Body Construction

14.
Bonding Strip - Body Rear Upper

Panel to Quarter Panel

- Right Hand

15.
Support - Body Rear Upper Panel

16.
Panel - Body Lock - Right Hand

17.
Pane! - Body Lock Pillar - Right Hand

18.
Panel - Rear Quarter - Right Hand

19.
Shield Rear Quarter Splash

20.
Panel - Body Rear Upper

21.
Extension - Body Rear Upper Panel

Support - Right Hand

and Left Hand

22.
Bonding Strip - Body Rear Upper

Panel at Body Rear Lower

23.
Bonding Strip - Body Lower Panel

to Right Hand Quarter Panel

24.
Bonding Strip - Rear Filler Panel

Lower - Right Hand
25.
Panel - Rear Filler

26.
Bonding Strip - Rear Filler Panel

. Lower - Left Hand

27.
Bonding Strip -Body Lower Panel

to Left Quarter Panel

28.
Shield - Rear Quarter Splash

- Left Hand

29.
Bonding Strip - Body Rear

Upper Panel to Quarter

Panel - Left Hand

30.
Panel - Body Lock

31.
Panel - Body Lock Pillar

32.
Extension - Body Rear Upper Panel

33.
Panel - Rear Quarter - Left Hand

34.
Plate - Nut - Left Hand

35.
Striker Plate Assembly - Left Hand

36.
Body Rear Lower Panel

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-52

and pull weatherstrip and trim from rear bow.

Section A-A shows installed position of these com-

ponents. Refer also to figure 105.

installation

1.
Find and mark center of header, #3 bow, rear bow

and leading and trailing edges of top trim. Align

these marks during installation and recheck their

alignment from time to time while installation is in

progress, especially during tacking or stapling.

2.
Assemble top trim and weatherstrip to rear bow,

referring to Section A-A and Figure 105. Note that

filler strip locks this assembly together and goes

in last. Align center marks.

3.
If new pads are required, install at this time, align-

ing with marks made when old pads were removed.

Figure 106 shows pad construction; Figure 107 shows

pad installed.

4.
Install top trim-rear bow assembly on top frame

with four screws removed at disassembly.

5.
Lock down rear bow in desired "top up" position.

Pull up stay straps and staple or tack to #3 bow

(fig. 108).

6. Pull leading edge of trim iip to header and align

center marks. Smooth out fabric and clamp, tack

or staple temporarily to header.

7.
Draw window extension up to #3 bow, aligning cen-

tering marks. Turn an ample amount of fabric under

and tack to #3 bow. Apply neoprene trim cement,

GM Part #3695016 or equivalent, to area shown in

View D of Figure 102. Follow directions on package.

8. Draw roof portion of trim over #3 bow, align marks

and tack on staple.

9. Trim off excess material and install wire-on binding

as shown in Figure 109 and View D of Figure 102.

Install binding caps.

10.
Remove temporary clamps or fastenings holding trim

to header.

11.
With header locked down, pull trim assembly up tight

and mark for final installation.

12.
Apply trim cement to header and rear side rail.

13.
Release header from windshield. Tack or staple trim

to header (fig. 103).

14.
Apply trim to rear side frame, previously cemented.

15.
Install weatherstrips which were removed at dis-

assembly and install retaining screws in header

weatherstrip.

16.
Make any adjustments necessary, following instruc-

tions listed under Folding Top—Adjustments.

FRAME AND LINKAGE

Figure 110 illustrates construction features of the

folding top frame and linkage. Various cross sections in

Figure 110 show the pivoting joints and their assembly.

If an operation is being performed which requires

removal of folding top trim, follow directions in this

section. The entire frame assembly may be removed and

replaced as a unit. Follow instructions for Folding Top

Trim and Rear Window Assembly and Top Assembly—

Removal and Installation.

The pivoting joints should be lubricated with light

machine oil once a year. Apply oil sparingly so as not

to stain top trim.
WEATHERSTRIP

Side Rail Weatherstrip

Figure 111 illustrates installation of side rail weather-

strip which acts to seal window opening. The weather-

strip is held in place by studs which are part of the

weatherstrip assembly, and by neoprene base cement

which is applied between weatherstrip and side rail

surface.

When replacing weatherstrip remove all rust, old

cement and foreign material from the surfaces to be

cemented, to assure successful bonding. Use only good

quality neoprene cement suitable for weatherstrip

application.

Header Weatherstrip

Weatherstrip assembly is retained to the header panel

by a combination of studs, sheet metal screws and special

fasteners as shown in Figure 112, along with neoprene

base weatherstrip cement.

Figure 99 shows' a cross section of weatherstrip taken

through a special fastener. To replace fastener, rotate

ninety degrees to align fastener head with slot. Follow

directions for cementing in the Side Rail Weatherstrip

instructions preceding this write up.

ADDING HARDTOP (ROOF PANEL ASSEMBLY)

An available roof panel assembly (hardtop) complete

can be added to convertible model Corvettes. The hard-

ware is included with the panel assembly.

Reworking of a plastic part (one for each side of the

roof panel) can be used as a marker for drilling of two

required holes in the folding top compartment lid* Hard-

ware is attached at four locations — two on the lid and

two (one each side) at the lock pillar area as follows:

1.
Rework two plastic retainers (#6280765) (used on

Chevrolet and Corvair door inner panels for trim

retention) as shown by Figure 113.

2.
Slide the reworked plastic retainers into the bolt re-

tainer slots on each side of the hardtop rear bow

(position plastic tip inboard).

3.
Mark the hardtop reveal molding at the approximate

location of the two plastic retainers,

4.
Mark the tips of the two plastic retainers with a

china marker pencil.

5.
Close the soft top compartment lid.

6. With aid of an ^assistant, position front of hardtop

onto header and lower onto vehicle. Do not fasten

latches at windshield header.

7.
Apply hand pressure at reveal molding marks.

8. Mark roof panel attachment hole location at each

lock pillar area (fig. 114).

9. With aid of an assistant, lift roof panel straight up

off body and set roof panel aside.

10.
Mark the drill position at the four china marks with

a center punch.

11.
Place a 2" x 4" board under the top compartment lid

to prevent drill damage to folding top material. Make

certain the compartment lid is securely locked

before drilling.

12.
Drill 1/8" pilot hole at the 4 marked locations.

CHEVROLET CHASSIS SERVICE MANUAL