1953 JEEP DJ ECU

H

ELECTRICAL
SYSTEM
the condenser. Replace the condenser. If there is
no jump to full voltage, overhaul or replace the

distributor.

k.
With the points closed, connect the voltmeter

from
a clean, paint-free
post
on the distributor
body to the negative
post
of the battery. The volt­
age drop should be practically zero, a hardly
readable deflection on the voltmeter. If the volt­ meter registers a
voltage
drop, perform the checks

in
steps
1
and m following.

I.
Check
for
voltage
drop in the battery ground
cable.
Clean
the battery
post,
cable terminals, and contact surface on the bellhousing, or on body if

a
noticeable deflection of the voltmeter occurs,
m.
Check
for any
voltage
drop
between
the dis­

tributor
body and a clean, paint-free
spot
on the

cylinder
block. If there is any
voltage
drop, remove
the distributor and clean the mounting surfaces of
distributor
body and cylinder block.

H-5.
SECONDARY
CIRCUIT
If
satisfactory ignition is not obtainable with cor­

rect
point gap and tension; satisfactory condenser;
sufficient primary voltage; and correctly cleaned, gapped, and installed spark plugs; the secondary

circiut
should be investigated.

a.
Test the coil.
Bring
the coil up to operating
temperature using the coil heat feature of a coil tester, if available. Refer to the coil tester manu­

facturer's
instructions for specific hook-ups for
performing the checks given in
steps
b, c, and d following.
b. Connect the positive lead of the tester to the
battery terminal of the coil primary winding.
Con­
nect the tester ground lead to the coil tower. Mea­

sure
the resistance of the secondary winding. If the
resistance is more than
20,000
ohms, a fault in the
secondary winding is indicated.
c.
Check
for a grounded secondary by touching the tester ground lead to the coil cover. If resistance
is not over
100,000
ohms, the secondary is grounded
to the cover.

d.
If the secondary winding is satisfactory, mea­
sure
the primary current draw in accordance with
the instructions of the
test
equipment manu­
facturer.

e.
Check
the secondary circuit for leakage. With the coil primary in the circuit with the breaker unit of the tester, connect a long, high-tension
test
lead
to the coil tower.
Check
the secondary circuit for
leakage by performing the checks given in
steps
f. g, h, and i following.

Note:
In the following
tests,
a slight sparking and
meter deflection
will
usually be
seen
just as contact
is made.
This
is caused by capacitance and
does
not
indicate defective insulation.
f.
Check
distributor cap. Remove the coil lead from the cap and touch the
test
lead to the center contact
inside the cap. If the meter reading drops when the contact is touched or if sparking is seen, a leakage
path is present
between
the center contact and one
of the plug towers.
This
leakage path
will
be in the

form
of a
crack
or carbon track in the cap. Discon­ nect the spark plug wires from the cap one at a
time and
test
each plug contact with the high-
voltage
lead and with all other plug wires con­
nected. Any sparking or meter drop indicates that

a
leakage path exists
between
that particular con­
tact and an adjacent one. Testing the adjacent contacts
will
determine which pair is at fault,
g-
Check
distributor rotor. Touch the
test
lead to
the spring contact in the center of the distributor
rotor.
Any leakage in the rotor insulation
between

the contact and the shaft
will
cause a drop in the meter reading and usually sparking
will
be seen.

h.
Check
spark plug wires. Disconnect the spark
plug wires from the plugs and
test
the plug terminal of each. The meter reading should not drop below
the open secondary value (value before making contact). If it
does
or if a large spark occurs when
the
test
lead and the plug wire are separated, there
is a break in the insulation on that wire.

i.
Check
the coil tower insulation. Remove the
high-tension
test
lead from the coil tower and touch
the ground lead of the coil tester to several points

around
the base of the tower. Any sparking or deflection of the meter indicates a leakage path in
the tower insulation.

H-6.
Alternator Charging System

All
Jeep
Universal
Series vehicles have, as standard
equipment a 35-amp., 12-volt, negative ground
alternator and a transistorized
voltage
regulator.
For
repairing the alternator, many of its major components are furnished as complete assemblies

including:
complete brush assembly which requires no soldering or unsoldering of leads; two complete
rectifying
diode
assemblies which eliminate the need for removing and replacing individual diodes;

a
complete isolation
diode
assembly; and a rotor assembly complete with shaft,
pole
pieces, field coil,

and
slip rings.

The
transistorized
voltage
regulator is an electronic
switching device. It
senses
the
voltage
appearing at the auxiliary terminal of the alternator and
supplies the necessary field current for maintaining the system
voltage
at the output
terminal.
The out­
put current is determined by the battery electrical

load;
such as headlights, heater, etc.
The
transistorized
voltage
regulator is a sealed unit,
has no adjustments, and must be replaced as a
complete unit.

H-7.
Starting System

The
operation of the starter motor is controlled by
the ignition switch. The starter is made up of a
frame,
field coil, armature, and brushes.

The
starter solenoid electrically
closes
the circuit

between
the battery and the starter motor. When the ignition key is turned to its extreme right, the
solenoid is energized and
closes
the battery-to- starter-motor circuit.

Note:
All Jeep Universal Series vehicles have the

starter
solenoid switch secured to the starter motor
assembly. The Hurricane F4 and Dauntless V-6

engine
Prestolite starter drive is of the inertia type
(rexr
continued on
page
176) 174

H

ELECTRICAL
SYSTEM

ffKHs)

3—<§)

FIG.
H-7—WIRING
DIAGRAM—V6
ENGINE
CURRENT
MODEL
1—
Left
Headlamp
2—Left Parking and Signal Lamp
3— Right Parking and Signal Lamp
4—Right Headlamp 5—
Marker
Lamp — Amber
6— Alternator 7— Voltage Regulator
8— Starting Motor
9— Battery Ground Cable
10— 12 Volt Battery
11—
Flasher
(Directional Signal)
12— Instrument Cluster
A—Hi-Beam
Indicator
B—Auxiliary

C—Instrument
Lights

D—Oil
Pressure Indicator
E—Charging
Indicator

F—Temperature
Indicator

G—Fuel
Gauge Indicator
H—Instrument Voltage Regulator
13— Ignition and Starter Switch
14—
Horn
Button
15— Directional Signal Switch
16— 4-Way Flasher Switch 17—
Flasher
(4-Way)
18— Windshield Wiper Motor Switch
19—
Main
Light Switch
20—
Fuel
Gauge
Tank
Unit
21—
Back-Up
Light Switch
22—
Marker
Lamp — Red
23— Right
Tail
and
Stop
Light 24— Right Back-Up Lamp
25—
Left
Back-Up Lamp 26—
Left
Tail
and
Stop
Light
27—
Marker
Lamp — Red
28—
Stop
Light Switch
29— Foot Dimmer Switch
30— Windshield Wiper Motor Assembly
31—
Ballast
Resistor 32— Ignition
Coil

33—
Spark
Plugs and Cables 34— Temperature Sending Unit
35—
Oil
Pressure Sending Unit 36—
Horn
37— Junction Block
38—
Marker
Lamp — Amber

lions
on the terminal
posts.
Be sure
condenser
is
mounted
firmly on the distributor for a
good
ground
connection.

Should a
condenser
tester
be available the capacity for
both
F4 and Prestolite V6
condenser
should
check from .25 to .28 microfarads. In the
absence

of
tester,
check by substituting a new
condenser.

H-13. Distributor Points
a. Examine the distributor
points.
If
they
show

wear,
poor
mating, transferred metal, or pitting,

then
new
ones
should be installed. Clean the
points

with a suitable
solvent
and a stiff bristled brush.
b. Check the
alignment
of the
point
for a full,
square
contact.
If not correctly aligned, bend the
stationary
contact
bracket slightly to provide align­
ment.

c. The
contact
gap should be set at .020"
[0,508
mm.],
on the F4 and .016"
[0,406
mm.] on the
Prestolite V6. Adjustment of the gap is accom­ plished by
loosening
the lock screw and turning adjusting eccentric screw until correct gap is
secured. Be sure that the fiber block on the breaker

arm
is resting on the
highest
point
on the cam while the adjustment is
being
made. Recheck the gap
after locking the adjustment.
d. Apply a thin film of cam lubricant to the cam to
lessen
fiber block wear.
e. Using Tool C-4094, check
point
contact
spring
pressure, which should be
between
17 and 20

ounces
[0,487
a
0,567
kg.] on the F4 and 17 to 22 oz.
[0,487
a
0,624
kg.] on the Prestolite V6.

Check
with a spring scale
hooked
on the breaker

arm
at the
contact
and pull at right
angle
to the
breaker arm. Make the reading just as the
points

separate. Adjust the
point
pressure by
loosening
the stud holding the end of the
contact
arm spring
and slide the end of the spring in or out as
neces­

sary.
Retighten the stud and recheck the pressure. Too low a- pressure will
cause
engine
missing at
high
speeds.
Too high a pressure will
cause
rapid
wear of the cam, block, and
points.
180

ELECTRICALJ
SYSTEM

d.
Inspect for
excessive
wear
between
centrifugal

weights
and advance cam and pivot pins.
Turn
weight
base plate in a clockwise direction until
weights
are fully extended. Release and allow
springs to return
weights
to
retard
position. Repeat several times. Springs should return
weights
to
stop
without sticking and there should be no
excessive
free
movement
in the
retard
position. Inspect
springs for distortion and fatigue.
e. Inspect cam
lobes
for scoring or
excessive
wear.
Check
weight
base plate for binding or
excessive

looseness
on distributor shaft.

f.
Check
breaker plate for
excessive
looseness
on
outside
diameter of upper distributor shaft bushing.
Check
breaker plate ground lead for poor
spot
we
Id

at plate end and for
loose
or frayed terminal con­
nections.
g.
Check
for
excessive
wear
between
distributor
shaft and bushings in housing. Inspect shaft for distortion. Inspect gear for scoring of
teeth
or

excessive
wear.

h.
Inspect rod end of vacuum advance mechanism
for
excessive
wear. Push rod
into
unit as far as
possible, hold finger tightly over nipple, then re­
lease
rod. After about 15 seconds, remove finger
from nipple, and
notice
if air is drawn
into
unit.
If
not, diaphragm is leaking and unit must be
replaced.

H-29.
Distributor Reassembly

Refer
to Fig. H-l5.

a.
Install
distributor
primary
lead and rubber grommet in distributor housing. Mount vacuum
advance unit on housing with two
slotted
attaching
screws; insert ground lead terminal of breaker plate under outer mounting screw.
b.
Install
felt
washer over upper shaft bushing of
distributor housing and apply a few drops of light

oil.
Secure breaker plate to upper bushing with re­ tainer. See Fig. H-17.
12767

FIG.
H-17—INSTALLING
BREAKER
PLATE
ON
DISTRIBUTOR
HOUSING
(DELCO)

1—
Breaker
Plate
2—
Retainer

3—
Retainer
Groove
4—
Lubricant
Reservoir c.
Install
distributor cam and
weight
base plate
on distributor shaft.

d.
Insert distributor shaft
into
distributor housing.
Install
centrifugal advance
weights
and springs on

cam
and
weight
base plate. e. Fasten driven gear to shaft with pin. Be care­
ful
not to damage gear.

f.
Secure condenser and bracket to breaker plate
with
slotted
screw.
g.
Install
breaker point assembly over
boss
on
breaker
plate; secure with two
slotted
screws and
lock washers. Apply one drop of light oil to breaker

arm
pivot. Connect condenser and coil
primary

leads to breaker point assembly.

h.
Apply a small amount of high temperature cam

and
ball
bearing lubricant to a clean cloth; hold cloth against distributor cam while turning
distri­
butor shaft.

Caution:
Do not apply
excessive
grease. Petro­
leum jelly is not suitable as a distributor cam
lubri­
cant.

i.
Make preliminary adjustment of breaker point
gap, as described in Par. C-10.

].
Secure rotor to centrifugal timing advance mech­
anism with two screws, lock washers, and flat
washers.

Note:
The square and round
lugs
on the rotor must
be positioned in the corresponding
holes
in the

weight
base plate.
k. If a reliable distributor tester is available, check
the distributor to make certain that the centrifugal

and
vacuum advance mechanisms are operating
according to specifications.

Note:
Mount distributor in tester with all end play
of the distributor shaft in upward position; this

will
eliminate any possible drag
between
the centri­ fugal advance cam and
weight
base plate.

I.
Install
new
O-ring
seal on distributor housing.

H-30.
Distributor
Installation
and
Timing

a.
Insert distributor shaft
into
timing gear cover
of
engine
so that rotor is pointing to
mark
made on distributor base (Fig. H-14), with vacuum advance
unit pointing in exact, original direction (Fig.

H-18).

b.
Install
distributor clamp and
bolt
with lock
washer, leaving
bolt
just
loose
enough
to permit
movement
of the distributor with heavy hand
pressure.

C.
Connect
primary
wire to distributor side of coil.
Install
distributor cap on distributor housing. Press

screwdriver
into
upper
slotted
ends
of two cap
retainers.
Turn
retainers clockwise to secure cap to distributor.

d.
If
spark
cables were disconnected from
distri­

butor cap, connect them. Wires must be pushed

all
the way down
into
the distributor cap terminals
and
onto
the
spark
plugs. Nipples must be pushed
firmly
over the terminals;
boots
must be pushed

firmly
over the
spark
plugs. 186

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

H

U029p 1—
Oil
Retainer

2—
Bearing

3—
-Felt
Wick
4—
Oiler

5—
Commutator
End Head
6—
Brush
Lead
Screw
7—
Lockwasher

8—
Brush
Set
9—
Brush
Spring

10—
Brush
Arm

11—
Frame

12—
Insulating
Bushing

13—
Washer

14—
Lockwasher

15—
Hex
Nut
16—
Lockwasher
FIG.
H-20—GENERATOR

17—
Hex
Nut
18—
Ground
Screw
19—
Lockwasher

20—
Hex
Nut

21
—Lockwasher

22—
Hex
Nut

23—
Lockwasher

24—
Washer
25—
Insulating
Washer
26—
Insulating
Bushing
27—
Stud

28—
Left
and Right
Field
Coil

29— Pole Shoes
30— Pole Shoe Screw

31—
Drive
Pulley and Fan Assembly
3
2—Lockwasher
33—
Shaft
Nut
34—
Drive
End Head

35—
Felt
Washer
36—
Felt
Washer Retainer
37—
Ball
Bearing
38—
Gasket

39—
Bearing
Retainer
40—
Lockwasher

41—
Retainer
Screw

42—
-Felt
Washer

43—
Woodruff
Key
44—
Armature

45—
Thru
Bolt
4
6—Lockwasher

with
instructions furnished with the testing equip­ ment.

H-38.
Field
Coils
Inspect the field coils for chafed wires and using

test
lamp prods check for both open and grounded

circuits.
To
test
for open coil, connect the prods
to the two leads from each coil. If the lamp fails
to light, the coil is open and must be repaired or

replaced.

To
test
for ground, place one prod on ground and
the other on the field coil terminal. If a ground is present the lamp
will
light and the coil must be

repaired
or replaced.
If
accurate
test
equipment is available, check the
field coils for current draw which should be with­
in
the limits of 1.2 to 1.3 amperes at 10 volts for both coils.
A shorted coil
will
of course show a much higher
draw,
while an open coil
will
show no draw. In
either case the generator output
will
be below
normal.

To
replace a field coil, disconnect the field termin­

als,
use a heavy screwdriver to remove the field

pole
piece screws, then the coils
together
with the

pole
pieces may be removed. When replacing the coils, set the
pole
piece screws by staking with a
center punch.

H-39.
Brush
Holders

With
test
prods check the insulated brush holder
to be sure it is not grounded. Touch the brush
holder with one prod and the frame with the other prod. If the lamp lights, a grounded brush holder is indicated.
Inspect the brush holders for
cracks,
distortion and

improper
alignment. The brushes should slide freely

and
should be in perfect alignment with the com­ mutator
segments.

H-40.
Assembling Generator

Install
the felt grease retainer and washer in the

drive
end head. See Fig. H-20.
Check
the bearing to be sure it is clean and
fill
it one-half full with

a
high melting point grease.
Install
the bearing
and
also install the inside felt washer and attach
the bearing retainer with the lockwashers and

screws.
Place the drive end head over the front end
of the armature shaft.
Install
the Woodruff key in the armature shaft and install the drive pulley,
being sure the key is in position. Secure in position

with
the washer and nut. Place the assembly on 189

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

H
Resistance
should be approximately 0.1 ohm.

An
extremely accurate instrument would be neces­
sary
to ascertain shorted turns.
Only
an open condi­
tion can be detected with a commercial ohmmeter.

If
the alternator has been disassembled because of
an
electrical malfunction, replace stator only after

all
components have been checked and found to
be satisfactory.

H-85.
Out-Of-Circuit
Rectifier Diode Test

With
the rectifier diode heat sinks disconnected
from
the stator assembly (Par. H-80), the diodes

can
be individually checked with the Diode Tester

C-3829.
FIG.
H-36—RECTIFIER
DIODE
TEST
POINTS

1— Diode Plate Stud

2—
Diode Terminals

Fig.
H-36 shows the
test
point location for either positive or negative diode.

Plug
Tester C-3829 into a 110-volt AC outlet.
Connect
alligator clip to diode plate stud, and the probe of the tester to each of the three diode ter­

minal's
test
points. Negative diodes
will
give a
negative deflection of the needle and positive
diodes
will
give a positive deflection. The meter

reading
should be the same for each of the diodes

and
should be 2 or over for a
good
diode. If a diode is faulty, replace the entire diode heat sink
assembly. H-86.
Assembling Alternator

Refer
to Fig. H-31.

a.
To install front bearing in front housing, press
the bearing into place on an arbor press using

Bearing
Installer C-3858. Position the split spring

washer
in the front bearing housing oh top of the bearing.

b.
Install
the
rear
bearing on the rotor shaft front
end using Bearing Installer C-3935 as shown in

Fig.
H-37.
FIG.
H-37—INSTALLING
REAR
ROTOR
BEARING

1—
Rear
Bearing Installer C-3935

2—
Rotor
Shaft
C.
Place the rotor assembly
into
position in the
front housing by tapping rotor shaft on a
soft

wood surface.

d.
Position diode assemblies and stator as a unit
into the
rear
housing. Make certain that insulator
washers and insulator
sleeves
are correctly posi­
tioned on the positive diode assembly.

e.
To assemble the subassembly halves of the
alternator
(front
housing and
rear
housing). Slide
the front housing over the stator.
Install
the bolts
and
nuts.
f. Position first the spacer, then the woodruff key
on the rotor shaft and slide on the fan.
Carefully

position the alternator in a vise with the clamps
of the vise held to the pulley. Position the pulley
so it is just starting to slide over the woodruff

key.
Press it into position by tightening nut with

a
wrench. When the pulley is properly positioned,
remove the nut, place the lock washer on the

rotor
shaft, and again replace the nut.

g.
Install
the isolation diode assembly and secure

with
locknuts.

h.
Install
the brush housing in position in the
rear

housing.
Install
the brush housing cover and the
tapping screws.

i.
Turn
the rotor by hand listening carefully to

make
certain there is no interference between the

rotor
and the stator winding.
H-87.
Alternator Installation

To
install the alternator, reverse the procedure 201

H

ELECTRICAL
SYSTEM
FIG.
H-38—WIRE
COLOR CODE
AND

LOCATIONS
FOR
ALTERNATOR HOOK-UP

1— Regulator (Auxiliary)
Terminal
(Cable —
Grey)

2— Output
Terminal:
(Red)

3—
Regulator
Terminal
(Cable —
Grey)

4—
Ground
Terminal
(Cable — Black-White
Tracer)
5—
Field
Terminal
(Cable — Green-White
Tracer)

6—
Ground
(Optional)
Terminal
(Cable — Black-White
Tracer)
REAR
VIEW

35
AMP.
ALTERNATOR
REAR
VIEW
40
& 55 AMP.
ALTERNATOR
given in Par. H-78, adjusting the fan belt to its
proper tension after the alternator is mounted, as described in Par. C-27. Wires should be connected
as shown in Fig. H-38.

When
the vehicle is equipped with a radio, a .55
mfd. capacitor is required on the alternator. Mount
the capacitor strap to a ground terminal and con­
nect the lead to the output terminal.
H-88.
STARTING
SYSTEM
SERVICE
H-89.
Ignition
Switch

The
ignition switch serves both to energize the
ignition system and
engage
the starter switch.
The
ignition switch has four positions: (1) AC­

CESSORY,
(2)
LOCK,
(3) ON, and (4)
START. The
key must be in the switch to turn it to any position other than
LOCK,
and the key can be
removed only in the
LOCK
position.
In "ACC",
a connection is made from the battery

terminal
to the accessory terminal of the switch to
allow accessories such as the radio, blower and/or
windshield wiper to be operated with the ignition, fuel
gauge
and indicator light circuits off.
In "LOCK",
no accessory supplied through the
ignition switch can be operated. Also, the ballast
resistor (V-6
engine
only) circuit to the ignition
coil
(IGN) is grounded.
In
"ON", a connection is made from the battery

terminal
to the accessory terminal so that all
ignition switch supplied accessories can be operated. Also the battery is connected to the ballast resistor
(V-6
engine
only) leading to the ignition coil

(IGN).
From
this same terminal, a lead
into
the
instrument cluster energizes the fuel
gauge
and
indicator lights.
In "START",
all ignition switch supplied acces­
sories are temporarily disconnected. A connection is made to the starter solenoid lead. The charge

and
oil indicator lamps
will
light until the
engine
is started.
H-90.
Ignition
Switch
Removal

a.
Remove the bezel nut and pull back the main
switch body.
Lower
the switch
body
from under the instrument panel so that the wiring harness plug

can
be removed from the prong connection,
b. If the lock cylinder is to be removed, turn the
ignition key to the right and insert a short
piece

of wire or end of a paper clip
into
the lock release

hole
in the switch body. Pressing on the lock
cyl­
inder retainer
will
allow the cylinder to be removed.
H-91.
Ignition
Switch
Installation

Before installing the lock cylinder
into
the main
switch body,
note
the position of the lock cylinder
retainer.

a.
Place the lock cylinder
into
the main switch
body
with the highest part of the lock cylinder
retainer in line with the lock release
hole
in the
main
switch body.
b. Compress the lock cylinder retainer so that the
lock cylinder can be installed all the way
into
the

main
switch
body
or until the retainer can be

seen
through the pin hole.

c.
Install
wiring harness plug
onto
switch
body

prong connection.

d.
Install
this main switch
body
into
the instru­
ment panel opening from the
rear.

e. To make sure that the switch is in its correct position, install the ignition key in the off position.
Then
turn the switch
body
until the key is straight
up and down. Remove the key, install the bezel
nut and secure.
H-92.
PRESTOLITE
STARTING
MOTOR
DAUNTLESS
V-6 and

HURRICANE
F4
ENGINE

The
Prestolite starting motor on the V6
engine
is

similar
in construction (with exception of pinion housings) to the starting motor installed on F4

engines.
The
starter solenoid switch is bolted to the starter
frame.

The
starter is equipped with
sealed-type
absorbent
bronze bearings and no lubricant is required. Service procedures for the Prestolite starter are
given in
Pars.
H-93 to H-107. 202

UNIVERSAL
SERIES
SERVICE
MANUAL

H

t
^

12956

FIG.
H-41—PRESTOLITE
STARTING
MOTOR—V-6
ENGINE

1—
End
Plate
2—
Oiling
Pad

3—
Thrust
Washer
4—
Brush
Plate Assembly 5—
Screw

6—
Lock
Washer 7—
Insulating
Washer
8—
Terminal

9—
Field
Coil
and Pole Shoe

10—Frame
11—
Insulating
Washer
12—
Washer

13— Nut
14
—Lockwasher

15—
Insulating
Bushing
16— Pole Shoe Screw
17—
Bearing,
Outer
18—
Drive
End
Frame
Pinion Housing
19— Intermediate Bearing Housing
20—
Lock
Washer 21—
Screw

22— Bendix Drive
23—
Thrust
Washer

24—Pin

25—
Armature

2 6—Commutator
27—
Thru
Bolt
28—
Insulator

29—
Bearing,
Intermediate
and
the armature rotated slowly by hand. If a
shorted coil is present, the steel strip
will
become
magnetized and
will
then vibrate.
H-101-
Field
Coils

Using
test
probes, check the field coils for both
ground and
open
circuits.

a.
To
test
for ground, place one probe on the motor frame or
pole
piece
and touch the other probe to the field coil terminals. If a ground is present, the
lamp
will
light.
b.
To
test
for
open
circuits, place the probes on
the field coil terminal and on an insulated brush.
If
the light,
does
not light, the coil is
open
circuited.
H-102.
Brush
Holder Inspection

Using
test
probes, touch the insulated brush holder with one probe and a convenient ground on the commutator end head with the other probe. If the
lamp lights, it indicates a grounded brush holder.
H-103.
Starting Motor Reassembly

Refer
to Fig. H-40 and H-41.

a.
When assembling absorbent bronze bearing
found in the end plate and drive end frame, always
use the proper arbor
designed
to
give
the proper
bearing fit. Soak the bearings in oil
before
assem­
bling in the bearing bore. Give the bearing
seats

a
light coating of oil.

Note:
At assembly, the outer pinion housing bear­
ing must be flush with the bearing bore on the inside of the housing; the intermediate bearing
must be flush with the bearing bore on the side
toward the armature.

b.
Brushes should be correctly installed and con­
nected as outlined in Par. H-98 in order to be sure
of proper starting motor efficiency.
c. Assemble the armature bearing plate and Bendix

Folo-Thru
Drive to the drive end frame.
Install
the two holding cap screws and lock washers. Tighten them securely. 205

H

ELECTRICAL
SYSTEM

FIG.
H-42—GROWLER
d.
Install
the armature in starter motor frame,
using care to align the four brushes and brush
springs on the commutator so that they are free to
move
and are square on the commutator.

e.
Install
the thrust washer on the shaft.
Lubricate

the plug and bearing in the end plate.
Install
the
end plate.
Install
the two through
bolts
and tighten securely.

f.
On Prestolite V6 starting motors, check pinion position by measuring from the centerline of the
pinion housing mounting bolt
holes
to the outside

edge
of the pinion.
Correct
measurement with the
Bendix
drive retracted is [19,05 mm.] to
%"
[22,23 mm.]; with drive extended, 1%"

[34,93
mm.] to 1^" [38,10]. Adjust by installing

thrust
washers just inside the commutator end
head or intermediate bearing as required. The
Bendix
drive retaining pin must not project
beyond the outside diameter of the pinion
sleeve.

H-104.
Bench Test

The
motor should first be checked to see that the
free running
voltage
and current are within specifi­ cations. To
test,
connect the motor to a battery,
ammeter and voltmeter. If the current is too high
check
the bearing alignment and end play to make

sure
there is no binding or interference. Using a

spring
scale and torque arm check the stall torque to see that the motor is producing its rated
crank­

ing power. The stall torque
will
be product of the

spring
scale reading and the length of the arm

in
feet.
If the torque is not up to specifications

check
the seating of the brushes on the commutator
and
the internal connection of the motor for high
resistance. The Bendix
Folo-Thru-Drive
should be checked for correct operation. The Bendix pinion
should be checked to see that it shifts when the motor is operated under no load.

H-105.
Bendix Folo-Thru Drive (Prestolite)
The
Bendix
Folo-Thru
Drive is designed to over­

come
premature demeshing of the drive pinion
from
the flywheel ring gear until a predetermined

engine
speed is reached. See Fig. H-43. No repairs or adjustments are possible on this

drive
and a
complete
new unit must be installed

if
trouble develops.

H-106.
Lubrication
of
Folo-Thru Drive
A
periodic cleaning and relubrication of the drive is advisable, the frequency of which
will
depend on
the type of service to which the vehicle is sub­
jected and the locale of operation.

a.
Remove the starting motor from the
engine
and take off the outboard housing. The pinion and

barrel
assembly
will
be in the demeshed position
on the screwshaft. Do not
move
it forward
until
after
that portion of the armature shaft ahead
of the pinion has been cleaned. If accidentally ro­
tated to the outer end of the screwshaft it
will

lock
in that position and cannot be forced back.

b.
Do not disassemble the drive for any reason.

c.
Do not dip or wash the drive in any cleaning solution.

d.
Do not remove the drive from the armature
shaft. Remove
excess
oil, grease or foreign matter
from
the armature shaft by wiping it with a clean cloth.
3
10859
FIG.
H-43—BENDIX
FOLO-THRU DRIVE

Dampen
the cloth with kerosene if necessary. A
light film of
SAE
10 oil may then be applied to the shaft.

e.
Now rotate the pinion and
barrel
assembly to the
fully
extended position, thereby exposing the screw­ shaft triple threads. Use a cloth dampened with
kerosene to wipe them clean. Do not use
gaso­
line
or any
commercial cleaner.
If the dirt is

thick
and gummy, apply the kerosene with a small

brush.
Tilt
the starting motor so that a small
amount
will
run under the control nut. Relubricate

with
a thin film of
SAE
10 oil. Use SAE 5 at ex­ tremely low temperatures.

f.
Reassemble the starting motor to the
engine
with the drive in the extended position.
Carefully
mesh the pinion with the flywheel ring gear before
tightening the starter motor mounting bolts. It may 206