1953 JEEP DJ manual transmission

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P
lengthening of the brake master cylinder eye bolt.

This
is
done
so the primary cup
will
clear the by­
pass port when the piston is in the off position,
otherwise the compensating action of the master

cylinder
for expansion and contraction of the fluid
in
the system, due to temperature changes,
will

be destroyed and cause the brakes to drag.

Note:
Some older 'Jeep' vehicles may
develop
side

movement
of the clutch and brake pedals resulting
from wear of the pedals, shafts, and bushings. One
way to
compensate
for this wear is to install a pedal

slack
adjuster kit,
Part
No.
921936.
FIG.
P-6—HAND
BRAKE
ADJUSTMENT

P-10.
Hand Brake

On
Model DJ-5 and DJ-6 vehicles the rear brake

shoes
are operated through cables and conduits to
form the hand or parking brake. A brake cable
equalizer and adjusting rod, Fig. P-6, is located directly back of the frame center cross member.

P-11.
Parking Brake Adjustment

•
Model DJ-5, DJ-6.

The
foot
brakes must be satisfactorily adjusted be­
fore attempting adjustment of the hand brake.

To
adjust the hand brake raise both rear
wheels

free of the floor.
Pull
up three
notches
on the hand

brake
lever and tighten the adjustment until the

rear
brakes drag slightly. Release the hand brake
lever and check the rear
wheels
for drag. The

wheels
must turn freely with the lever released.

P-12.
Transmission Brake Adjustment
The
transmission brake is located on the propeller
shaft at the rear of the transfer case, see Fig. P-4.
The
brake is operated by a cable connection from
the brake handle mounted on the instrument panel.

To
adjust the transmission brake, the following

sequence
should be followed:
Make
sure that the brake handle on the instrument
panel is fully released. Give due attention to the
cable and operating linkage to see that
they
do
not bind. If necessary free up the cable and
lubri­
cate it. Rotate the brake drum until one pair of the
three
sets
of
holes
are over the
shoe
adjusting screw

wheels
in the brake. Use the
edge
of the
holes
in
the brake drum as a fulcrum for suitable adjusting

tool
or a screwdriver, rotate each notched adjusting
screw by moving the handle of the
tool
away from
the center of the drive shaft until the
shoes
are
snug in the drum.
Back
off seven
notches
on the
adjusting screw
wheels
to secure proper running clearance
between
the
shoes
and the drum. Refer
to Fig. P-8.

P-13.
Relining Transmission Brake
Note:
The condition of the brake lining on the
transmission brake can be visually checked through
the adjusting
holes
in the brake drum.
FIG.
P-7—REMOVING
TRANSMISSION

BRAKE
DRUM

1— Tool W-172
2—
Adapter

3—
Brake
Drum
a.
To reline the brake
shoes
and make a major ad­
justment, first remove the four universal joint at­ taching nuts and lower the propeller shaft. Remove
the retracting spring clevis pin and the spring clip.
Remove the hug lock nut, the nut and washer from
the transfer case output shaft. Both the universal
joint companion
flange
and the brake drum may be readily removed by using puller Tool No. W-172

which
is illustrated in Fig. P-7. Remove the two

brake
shoe
retracting springs and the
shoes.

b. Clean all parts with a suitable cleaning solution

and
examine them for damage or wear.

Brake
shoes
may be distorted by improper lining
installation and the lining should be ground true
after installation on the
shoes.
For this reason it
is recommended that new or replacement
shoe
and
lining assemblies be installed.
c. To reassemble, first turn both adjusting screw

wheels
away from the center to "all off" position.
Place a light film of grease on the brake actuating

cam
and install the
shoes.
Install the black
shoe
re­

turn
spring next to the cam and the yellow spring next to the notch adjusting wheel screw. Place the
brake
drum and universal joint
flange
in position

and
install the transfer case output shaft washer,
nut and hug lock nut. 327

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

P

FIG.
P-9—WHEEL HUB OIL
SEAL
DRIVER
•
Removing the
Rear
Brake
Shoes.

•
Refer to Fig. P-ll.

a.
Using Tool C-3785 or equivalent remove the
upper linkage rod and brake
shoe
return springs.
b. Remove the brake
shoe
retainer, spring and pins.
c. Remove the anchor pin plate and tilt the brake

shoe
assembly out from the backing plate.

d.
On vehicles without a transmission brake,
spread the anchor
ends
of the primary and second­

ary
shoes
and remove the parking brake strut and
spring.

e. On vehicles without a transmission brake, dis­

engage
the parking brake cable from the parking
brake
lever and remove the brake assembly.
f. Overlap the anchor
ends
of the primary and
secondary
shoes
and remove the adjusting screw,
adjusting lever, lower return spring, and linkage
rods.
P-17. Inspection
Inspect the oil seals in the wheel hubs. If the con­
dition of any oil seal is doubtful, replace it. Install
the oil seal with an oil seal driver as shown in Fig.

P-9.

Brake
shoes
may be distorted by improper lining installation and linings should be ground true. For
this reason it is recommended that new or re­
placement
shoe
and lining assemblies be installed.
Using
brake drum micrometer C-3920 or equi­
valent, check all drums. Should a brake drum be rough and scored, it may be reconditioned by grinding or turning in a lathe. Do not remove more
than .030"
[0,762
mm.] thickness of metal .060" [1,52 mm.] overall diameter. If a drum is recon­
ditioned in this manner, either the correct factory-
supplied, oversize lining .030"
[0,762
mm.] must be
installed or a shim equal in thickness to the metal
removed must be placed
between
the lining and

shoe
so that the arc of the lining
will
be the same
as that of the drum.

If
it is found when
wheels
are removed that there
is brake fluid leakage at any of the wheel cylinders, it
will
be necessary to replace or recondition the
wheel cylinder (Par. P-21) and bleed the brake lines (Par. P-7).
Whenever the brake lining is replaced in one front
or one rear wheel, be sure to perform the same
operation in the
opposite
front or rear wheel, us­
ing the same brake lining part number. Otherwise, unequal brake action
will
result.
FIG.
P-10—STANDARD
FRONT
WHEEL
BRAKE

ASSEMBLY
WITH
LINK
TYPE
ADJUSTER 1—
Primary
Shoe
6—Lever
Plate

2—
Wheel
Cylinder
7—Linkage Rod (Upper)

3—
Secondary
Shoe 8—Screw
4—
Adjuster
Screw Assembly 9—Linkage Rod
(Lower)
5— Sleeve 10—Adjuster
Lever

P-18.
Brake
Shoe Installation

Refer
to Fig. P-10.

INSTALLING
THE
FRONT
BRAKE
SHOES

To
install the front brake
shoes
proceed as follows:

a.
Match a primary with a secondary brake
shoe
and
place them in their relative position on a

work
bench.

Note:
Primary
brake linings are color coded red

and
green. Secondary brake linings are color coded
white and green.
b. Lubricate the threads of the adjusting screw

and
install it
between
the primary and secondary

shoes.
The star adjusting
wheels
are stamped "R"

and
"L"
indicating thread rotation. The
left
front
brake
adjusting screw has right hand thread rota­
tion and the right front brake adjusting screw has
left
hand thread rotation. 329

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

P
f. On vehicles without a transmission brake hold
the brake
shoes
in their relative position and
engage
the parking brake cable
into
the parking

brake
lever.
g. On vehicles without a transmission brake in­
stall
the parking brake strut and spring
between

the parking brake lever and the primary
shoe.

h.
Place the brake
shoes
on the backing plate and

install
the retainer pins, springs and retainers.

i.
Install the anchor pin plate.

j.
Install the lever and
sleeve
on the primary
shoe
then install the secondary return spring, then the
primary
return spring.

Important:
A
"L"
or "R" is located on the hex­

agon
side of the lever crank for identification. The
lever crank marked "R" applies to the primary
shoe
on the
left
rear brake assembly. The lever
crank
marked
"L"
applies to the primary
shoe
on
the right rear brake assembly.
k. Place the upper linkage rod in the
groove
of the
anchor pin and
engage
the hook of the link rod
into

the adjusting lever.

I.
Install the brake drum. Install the wheel and

tire
assembly.
m. Adjust the brakes as described
below.

P-19.
Brake
Shoe
Initial
Adjustment —

a.
Should wheel brake units have
been
disassem­ bled for any reason, an initial adjustment
MUST
be made
before
drum installation.

b.
When the brake parts have
been
installed in
their correct position, initially adjust the adjusting
screw assemblies to a point where approximately Y% [9,53 mm.] of threads are
exposed
between
the

star
wheel and star wheel nut.

Note:
Following the initial adjustment and final
assembly, check brake pedal height to ensure

brake
operation. Then drive the car in reverse and
FIG.
P-12—BRAKE SHOE ADJUSTMENT
1—
Star
Wheel
2—
Lever

3—
Screwdriver
4—
Brake
Adjusting Tool
forward,
making 10 to 15 brake applications prior
to road testing.
This
action balances the adjust­
ment of the four brake units and raises the brake
pedal.
c. Adjustment may be made manually by remov­ing the access
slot
cover and using a brake adjust­
ing
tool
or screw driver to rotate the star wheel
until
the wheel is in the locked position. To tighten, rotate the star wheel in the clockwise direction.
Then
back off the star wheel at least 15 to 20

notches
(clicks).

d.
To back off the star wheel on the brake, insert
ice pick or thin blade screw driver in adjusting screw
slot
to hold lever away from adjusting screw.

Back
off on adjusting screw until wheel and drum

turn
freely. Replace adjusting
hole
cover.

Caution:
DO NOT attempt to back off on ad­
justing screw without holding adjuster lever away from screw as adjuster
will
be damaged.
P-20. Master Cylinder Reconditioning —
Dual
System

Refer
to Fig. P-13.

DISASSEMBLY
a.
Remove the filler cap and empty all fluid.
b.
Remove the snap ring, push rod assembly, and
the primary and secondary piston assemblies. Air pressure applied in the piston
stop
hole
will
help
facilitate the removal of the secondary piston as­
sembly.
c. The residual check valves are located under
the front and rear fluid
outlet
tube
seats.

d.
The
tube
seats
must be removed with the
self-

tapping screws supplied in the repair kit to permit removal of the check valves. Screw the self-tapping
screws
into
the
tube
seats
and place two screw

driver
tips under the screw head and force the
screw upward as shown in Fig. P-14.
e. Remove the expander in the rear secondary cup, secondary cups, return spring, cup protector,
pri­

mary
cup, and washer from the secondary piston.
f. The primary piston, with the rubber cups in­ stalled, is supplied in the repair kit.

CLEANING
a.
After disassembly, immersion of all metal parts
in
clean brake fluid or a brake system cleaner is
recommended. Use air
hose
to blow out dirt and cleaning solvent from recesses and internal pas­

sages.
When overhauling a hydraulic brake unit,
use all parts furnished in the repair kit. Discard
all
old rubber parts.

b.
After cleaning, place
all"
hydraulic
system parts
on clean paper or in a clean pan.

INSPECTION
Inspect all other parts for damage or
excessive

wear.
Replace any damaged, worn, or chipped
parts.
Inspect hydraulic cylinder bore for
signs
of
scoring, rust, pitting, or etching. Any of
these
will
require
replacement of the hydraulic cylinder. 331

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

T
FIG.
T-7—TAIL
GATE
ASSEMBLY

—
LATE
MODEL
CJ-5, CJ-6
T-6.
Care
of
Fabric
Tops
Remove fabric
tops
from their protective covering
immediately after they are received. Store in a

dry,
clean,
airy
place. If the material is damp, the
top should be installed on the vehicle immediately

and
washed with a mild soap; then
give
the top a

quick
and thorough rinsing.
T-7.
Brake
and
Clutch Pedal Pads

A
clutch and brake pedal pad cover has been re­ leased which has a .44" [11,18 mm.]
groove
molded into the back side of the pad cover. When installing,
the grooved opening is located down and to the

bottom
of the pedal. See Fig. T-ll. The purpose of the
groove
concerns models not listed in this
manual.
The pedal pad cover formerly used is
FIG.
T-8—VEHICLE
CONTROLS
—
LATE

CJ-5
AND CJ-6
SINGLE
LEVER
TRANSFER
CASE
1—
Light
Switch

2—
Windshield
Wiper
Switch

3—
Hazard
Warning
Light
Switch
4—
Hand
Throttle*

5—
Choke
Control

6—
Brake
Warning
Light*

7—
Windshield
Washer
Control

8—
Ignition
Starter
Switch

9—
Cigarette
Lighter*

10—
Turn
Signal
Lever

11—
Instrument
Cluster

12—
Horn
Button

13—
Glove
Compartment

14—
Transfer
Case
Shift
Lever

15—
Transmission
Shift
Lever

16—
^Heater
Controls*

17—
Accelerator
Pedal

18—
Brake
Pedal

19—
Clutch
Pedal

20—
Hand
Brake
Control

21—
Headlight
Dimmer
Switch

*On
applicable models only. solid in construction without groove.
Either

grooved and solid pad covers can be installed on

CJ-3B,
CJ-5,
CJ-5A,
CJ-6,
CJ-6A,
DJ-5 and DJ-6 models.
T-8.
Front Seat Adjustment
The
Bostrom bucket type driver's seat installed on

early
Models CJ-5, CJ-6, DJ-5 and DJ-6, are equipped with a 3-position manual adjustment.
Three
attaching
holes
are provided in the seat
support at the four seat mounting locations. To
adjust
the seat, remove the four attaching bolts,

move
the seat and four mounting spacers to the
desired
location, and reinstall the
bolts
at the new
location. Refer to Fig. T-12.

On
late models the driver's seat may be quickly ad­

justed
to the most comfortable driving position by releasing the lever located at the lower left front

edge
of the seat. Pushing the lever to the right al-
CD CD®
®@©"®^
FIG.
T-9—VEHICLE
CONTROLS
—
CJ-5,

CJ-6
DUAL
LEVER
TRANSFER
CASE

1—
Light
Switch

2—4-Way
Flasher
Switch*

3—
Hand
Throttle

4—
Choke
Control
5—
Brake
Warning
Light*

6—
Ignition-Starter
Switch

7—
Instrument
Cluster

8—
Horn
Button

9—
Qlove
Compartment

10—Heater
Controls*

•On
applicable models only.
11—
Front
Axle
Drive
Shift
Lever

12—
Transmission
Shift
Lever

13—
Aux.
Range
Shift
Lever

14—
Accelerator
Pedal
15—
Brake
Pedal
16—
Clutch
Pedal

17—
Headlight
Dimmer
Switch

18—
Hand
Brake
Control

19—
Turn
Signal
Lever
355

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

u
MISCEIiLaNEOUS

Contents

SUBJECT
PAR.

Abbreviations
U-15
Extra
Equipment U-2

Front
Bumper Weight U-9
Governor
U-3

Governor
Adjustment U-4

Governor
Maintenance. U-6

U-1. GENERAL

Miscellaneous information included in this sectioi
includes coverage of extra equipment, special
tools,
torque specifications, and charts and tables.

U-2. EXTRA
EQUIPMENT

Much
of the utility of the
*
Jeep*
Universal
is due to
the extra equipment which has been designed to adapt it for farming and industry. The mainte­
nance and use of
some
of this equipment is out­
lined
in this section.

U-3.
Governor Assembly

The
Novi governor is supplied for models equipped

with
the F4 engine.
This
is a centrifugal type governor and is illustrated in Fig. U-2. Complete

installation
instructions are supplied with each
assembly. Adjustment and operating procedures

are
given below.

U-4.
Governor Adjustment

a.
Adjust the carburetor to obtain smooth
engine

idle at 600 rpm., then
stop
the engine.
b.
Check
throttle linkage to ensure maximum
throttle opening. Be certain that throttle and
governor linkage is free.

c.
Place the carburetor throttle in wide-open posi­ tion and
pull
the governor control handle out to
the last notch. Adjust the governor to bellcrank

rod
so that the linkage
will
hold the carburetor
throttle in wide-open position.

d.
Close the governor control and start the
engine

Again
pull
the control out to the last notch and

adjust
the length of the cable at adjusting yoke so
that the
engine
will
run at
2600
rpm. Close the

control
to recheck the linkage for free action and
to make sure the
engine
will
return to 600 rpm.
idle speed.

If
the
engine
runs faster than this speed,
loosen

the lock nut which locks the governor hand control
handle on the dash to the rod and back off the
handle until the carburetor idle speed adjusting

screw
bears on the stop. Tighten the lock nut.
In
the absence of electrical tachometer equipment,

engine
speed may be determined by the speedom­
eter. Safely
jack
up the
rear
wheels and be sure the front wheel drive is not
engaged.
When driving
the
rear
wheels in high or direct transmission gear,
the
speedometer
will
read from 13j^ to 15 mph. [21.6 to 24.0 kph.] at an
engine
speed of from 900
to 1000 rpm.
SUBJECT
PAR.

Heater
U-10 Miscellaneous Data U-16

Pintle
Hook 1X7
Special
Tools. U-ll
Torque
Specifications U-13, 14, 15

Standard
and Recommended Tools
j.
.U-12

U-5.
Novi Governor Operation /

The
Novi governor is directly belted to the F4

engine
as no clutch is provided to disconnect the
drive.

To
operate the vehicle
WITHOUT
governor con­
trol,
push the governor hand control all the way
IN
against the instrument panel.

To
operate the vehicle
WITH
governor control,

pull
the governor hand control handle out. The
hand
control has nine notched positions. Pulling the

control
out to the first notch
sets
the controlled

engine
speed at approximately 1000 rpm. and each successive notch increases the speed 200 rpm.

until
2600
rpm. is reached in the ninth notch. The

hand
control may be released by turning the han­ dle one-quarter
turn
in either direction.

When
the
engine
is being operated under governor

control
(hand control out) the controlled
engine

speed may be
exceeded
at any time by depressing
the
foot
accelerator in the conventional manner to
secure a greater carburetor throttle opening than
that determined by the governor hand control
setting.

U-6.
Governor Maintenance

The
belt tension may be adjusted by raising or
lowering the governor in the slotted
holes
in the mounting bracket. Keep the pulleys and belt free
of
dirt
and oil. Belt slippage
will
affect governor
operation and a tight belt may cause
rapid
wear
of the governor shaft and bearings. Adjust it to
allow Yi' [12,7 mm.] depression midway
between
the pulleys with thumb pressure.
There
is little wear of the internal parts for they
operate in oil. The governor housings are equipped

with
both
fill
and
drain
plugs and also with level

indicating
plugs.
Check
the oil level at each vehicle
lubrication
and change the oil each time the en­

gine
oil is changed using the same grade oil used

in
the engine.

Caution:
Do not
fill
the governor housing above
the level plug. Overfilling
will
prevent governor
control
and possibly cause damage to governor in­

ternal
parts. The capacity of
these
governors is two fluid ounces [59,15 cm3]. The filler plug is
also a vent which should be cleaned thoroughly at
each oil change to be sure that the vent operates.

U-7.
Pintle Hook

The
standard type pintle hook, Fig. U-1, affords a
safe, easy hitch for towing a
trailer
or other vehicle. 357

u

MISCELLANEOUS
U-ll. SPECIAL TOOLS

Below are listed the
tools
applicable to
models
covered in this manual. These special
tools
are
essential not
only
for the
time
they
will
save
but

also
because
many
operations
described cannot be performed
without
them.

Note;
Tools W-274, W-283, and W-285 are univer­

sal
and can be used on all
engines.

Tool
Description
HURRICANE
F4
ENGINE

W-172 Puller, Timing
Gear,
U-Joint Flange, Vibration Damper W-231 Kit, Flywheel Dowel Installing
W-238 Driver, Intake and Exhaust Valve Guide

W-2
74 Pliers, Spark Plug Terminal Removal and Installing W-283 Gauge, Fan Belt Tension W-285 Studs, Oil Pan Gasket Aligning
C-690 Scale and Gauge, Piston Fitting

DAUNTLESS
V-6
ENGINE

W-274 Pliers, Spark Plug Terminal Removal and Installing
W-283 Gauge, Fan Belt Tension W-285 Studs, Oil Pan Gasket Aligning W-323
Rear
Main Bearing Cap Remover Bolt
W-338 Piston Pin Remover and Installer Set
J-6047-1
Support, J-6047-3 Spring,
J-6047-4
Driver, J-6047-5
Collar,
J-6047-20
Pilot
C-690 Scale & Gauge, Piston Fitting
J-5127-2 Carburetor Float Gauge
J-5830-1
Reamer, .004"
[0,102
mm.] Oversize

Electrical
Group

C-3858 Installer, Rotor, Housing and Shaft Bearing Assembly
C-3935 Driver, Alternator Rotor Bearing (Small) C-3936 Puller, Alternator Rotor Bearing (Small)
C-4068 Puller, Alternator Rotor Bearing (Large)

Transmission
Group

KF-128-A
Driver, Main Drive Shaft Bearing W-166 Arbor &
Sleeve,
Countershaft
Needle
Bearing Aligning
W-193 Arbor, Countershaft
Needle
Bearing Aligning W-194 Plate, Transmission Main Shaft Retaining
W-329 Puller — Main Drive
Gear
and Mainshaft Bearing (used with SP-5350 Adapters)
W-331 Driver Set — Main Drive
Gear
and Mainshaft Bearing (used with SP-5361 Driver Heads)
W-334 Thrust Yoke Tool — Second-Third Synchronizer Clutch Protecting W-335 Arbor — Countershaft
Needle
Bearing Aligning
W-336 Arbor — Reverse Idler Shaft
Needle
Bearing Aligning
C-3105 Driver, Mainshaft
Rear
Oil Seal (2WD)

Transfer Case
Group

W-130 Thimble & Driver, Shifter Rod Oil Seal
W-131 Thimble & Driver, Pinion Shaft
Rear
Bearing Cone
W-133 Driver,
Speedometer
Drive Pinion Bushing W-139 Driver, Output Shaft Front Bearing Cone Removing
W-141 Ring, Output Shaft Front Bearing Cone Removing
W-143 Driver, Output Shaft Front &
Rear
Oil Seal Installer W-176 Puller, Shift Rod Oil Seal
W-192 Pilot Pin, Transfer Case Intermediate
Gear
Thrust
Washer
W-251 Puller, Pinion Shaft Oil Seal, Transfer Case Front and
Rear
Oil Seal Removing

Universal
Joint Group

W-162 Tool, U-Joint Flange Installer
W-220 Jig & Bushing, Power-Take-Off U-Joint Pin Remover & Installer
C-3281 Wrench, U-Joint Holding 360

'Jeep9
UNIVERSAL
SERIES SERVICE
MANUAL
U PULLEY SPEEDS (R.P.M.)
- 8'
(20.3CM.) PULLEY

Governor
Control

Poeltlone
1-1
RATIO

Engine

Speede

Governor

Control

Poeltlone
TR

ANSMISS

HON
Engine

Speede

Governor

Control

Poeltlone
Lew
Inter.
High

1 306

682
857 1000

2
367
662
1028 1200

3
428
774 1200 1400

4
480 884
1372 1600

S
5S1 985 1542
1800
e 612 1105
1714 2000
7 673
1237 1885 2200

8
734 1326
2057 2400

9
796 1436
2228 2600
SPLINE SHAFT HORSEPOWER
The
chart
below shows
the
draw

bar
horsepower
at the
governor
controlled
engine
speeds
and
the
horsepower
at
the
spline shaft with
the vehicle stationary. Also
is

shown
the
horsepower available
at
the spline shaft with
the
vehicle at
the
maximum approved weight

(3500
lbs.) (1590
kg.)
moving
at

the speed shown
and
exerting
a

draw
bar
pull
of
zero pounds through
1200
pounds
(544 kg.)
(maximum
recommended)
in
steps

of 300 pounds
(136
kg.).

Governed Engine
R.P.M. Vehicle
Speed
M.P.H.* Draw
Bar

H.P**
H.P.
AT
P.T.O.
SPLINE SHAFT
Governed Engine
R.P.M. Vehicle
Speed
M.P.H.* Draw
Bar

H.P**
Vehicle
Stationary 3600
Lb

Vehicle
Mov

ng with
Governed
Engine
R.P.M. Vehicle
Speed
M.P.H.* Draw
Bar

H.P**
Vehicle
Stationary
No
Lbs.
Draw
Bar
Pull 300 Lbs.
Draw
Bar
Pull 800 Lbs.
Draw
Bar
Pull 700
Lbs.

Draw
Bar
Pull 1200
Lbs.

Draw
Bar

Pull
1000 2.2
7.18 16.3
13.7 11.9
10.2
8.4 6.6
1200 2.7 8.62 20.3
17.2
15.0 13.0
10.8 8.6
1400 3.1 10.06
24.5 20.8 18.3
15.9 13.3 10.8
1600 3.6
11.49 28.5 24.3 21.5
18.8 15.8 12.9
1800 4.0
12.93 33.0
28.6 25.3
22.2 19.0
15.8
2000 4.5
14.38 33.0 33.0
30.0 26.4 22.9
19.3
2200 4.9
15.80
33.0 33.0 32.5
28.5
24.7 20.7
2400 5.4 17.24
33.0 33.0 33.0 29.8 25.4
21.2
2600
%B
18.68 33.0
33.0 33.0
31.2 26.6
22.0
'Vehicle speed
in
low transmission
and
transfer case ratios.
••Based
on
maximum recommended draw
bar
pull
for
continuous service
—
1200
Lbs. 367