1953 JEEP DJ seats

M
FRONT
AXLE
1— Nut
2—
Lock
Washer

3—
Bearing
Lock
Washer
4—
Wheel
Bearing Cup 5—
Cone
and Rollers
6—
Oil
Seal 7— Spindle
8— Spindle Bushing
9—
Filler
Plug
10—
Right
Knuckle and Arm
11— Shims
12— Pivot Pin
13—
Lock
Washer
14—
Cap
Screw
15— Nut
16—
Washer

17—
Universal
Joint Yoke
18—
Oil
Seal
19—
Oil
Slinger
FIG.
M-2—FRONT
AXLE

20—
Cone
and Rollers
21—
Bearing
Cup
22—
Right
Axle Shaft with Universal Joint
23—
Knuckle
Oil Seal Retainer
24— Housing Breather 25—
Front
Axle Housing
26—
Axle
Shaft with Universal Joint
27—
Oil
Seal
28—
Axle
Shaft Guide
29—
Shim
Pack
30—
Bearing
Cup
31—
Cone
and Rollers
32—
Ring
Gear
and Pinion
33—
Thrust
Washer

34—
Thrust
Washer

35—
Differential
Gears
36— Housing Cover Gasket
37— Housing Cover
38—
Fill
Plug 39—
Screw
and
Lock
Washer
40—
Bearing
Cup
41—
Cone
and Rollers
42— Shims
43—
Lock
Pin
44—
Pinion
Shaft
45—
Differential
Case
47— Bolts
48— Nut
49—
Oil
Seal and Backing Ring
50—
Thrust
Washer
51— Snap Ring
52— Stop Bolt
53— Nut 54—
Bearing
Cup
55—
Cone
and Rollers
56—
Gasket

checked, making sure it is clean and open.

The
front wheel bearings should be checked every
12,000
miles. Refer to Section Q. Front wheel toe-

in
is adjustable by lengthening or shortening the
tie rod. However, standard caster and camber of
the front
wheels
are built
into
the axle. Wheel
caster can be adjusted by placing tapered shim
plates or
wedges
between
the springs and spring

seats
welded to the axle housing. Steering
geometry

and
front wheel adjustments are discussed in Sec­ tion O.

The
axle housing should be checked periodically
for weld cracks and/or other damage that may cause misalignment of the front
wheels
or
loss

of lubricant. The spring clips (U-bolts) should be
inspected and torqued every
12,000
miles. Torque (spring clip) nuts 45 to 50 lb-ft. [6,2 a 6,9 kg-m.].

M-4. FRONT
AXLE
REMOVAL
a.
Raise front end of vehicle
arid
safely support the frame by placing stands under the frame at
the rear of the front spring rear hangers.
b. Place
jack
under front axle housing and relieve
axle
weight
from the springs.
c. Disconnect shock absorbers from spring clip plates.
FIG.
M-3—HUB
CAP
PULLER

d.
Disconnect steering link from tie rod socket-
joint assembly.
e. Disconnect hydraulic brake
hoses
from front

brake
lines. Disconnect
hoses
from frame brackets. 278

FRONT
AXLE

FIG.
M-l
1—FRONT
STEERING

KNUCKLE

(With
Spicer Universal Joint)
1—
Wheel
Hub Cap

2—
Driving
Flange Cap Screw

3—
Axle
Shaft Drive Flange Gasket 4—
Wheel
Bearing Cup
5—
Front
Wheel Spindle
6—
Brake
Drum
7—
Front
Brake
Cylinder

8—
Brake
Backing Plate

9—
Pivot
Pin Bearing Cap
10—
Pivot
Pin Bearing Cap Nut
11—
Pivot
Pin 12—
Pivot
Bearing Adjusting Shims

13—
Pivot
Pin Cone and Rollers
14—
Steering
Knuckle
Oil Seal 15—
Front
Axle Universal Joint
16—
Thrust
Washer
17—
Brake
Backing Plate Screw
18—
Brake
Shoe and
Lining

19—
Hub
Oil Seal
20—
Wheel
Hub Bolt Nut
21—
Wheel
Bearing Cone and Rollers 22—
Wheel
Bearing Washer

23—
Wheel
Bearing Retaining Nut
24—
Wheel
Adjusting Nut
Lock
Washer
25—
Wheel
Bearing Retaining Nut
26—
Snap
Ring

c.
Install
the wheel bearing spindle and bushing.
d.
Install
brake backing plate.
e.
Grease and assemble wheel bearings and oil

seal.
Install
the wheel hub and drum on the wheel
bearing
spindle.
Install
the wheel bearing washer
and
adjusting nut. Tighten nut with
Wrench
W-144
as shown in
Fig.
M-5, until there is a slight drag on the bearings when the hub is turned.
Then
back off approximately one-sixth of a
turn.
Install
lock

washer
and nut, tightening nut
into
place, and then bend lip of lock washer over on the locknut.
f.
Install
drive
flange
and gasket on hub and attach
with
six cap screws and lock washers.
Install
snap

ring
on outer end of axle shaft.

g.
Install
hub cap.
h.
Install
the wheel, lug nuts, and wheel disc.
i.
If
tube
was installed with axle assembly on
vehicle, check front wheel alignment (Section O),
bleed brakes (Section P), and lubricate front axle

universal
joints (Section B).

M-12.
FRONT
AXLE
INSTALLATION

To
install the front axle, reverse the procedures described in
Par.
M-4 and then perform the follow­
ing operations:

a.
Torque spring clip plate (U-bolt) nuts securing the axle to the front springs, (see Par. M-4).

b.
Adjust and bleed the brakes (see Section P).

c.
Check
axle lubricant level and
fill
as necessary, (see Section B).

d.
Check
front end wheel alignment (see Section
O).
e.
Check
wheel turning angle. Refer to Par. M-14.
M-13.
Steering
Tie Rod and
Bell Crank

These
parts of the front axle are covered in Sec­
tion O.
M-14.
4-Wheel Drive
Turning
Angle

Adjustment
and service information regarding
turning
angles
is covered in Section O.

M-15.
2-WHEEL-DRIVE
FRONT
AXLE
The
front axle is of the reverse
Elliot
type. It is a
steel forging, heat treated for strength and ma­
chined
to
close
limits. The steering knuckles are
mounted on pins which pass through
openings
at each end of the
"I"
beam and are locked securely

in
position with tapered pins and nuts. The knuckles

ride
on
ball
thrust bearings for
ease
of steering. See
Figs.
M-12, M-13.

The
knuckles are connected by a tie rod which is
mounted on
ball
and socket connections. The tie

rod
is adjustable to secure correct
toe-in
of the front wheels. A steering connecting rod
connects

the
left
knuckle arm with the steering gear arm.

Standard
caster and camber of the front
wheels
are
built
into
the front axle. Wheel camber cannot
be changed however, caster can be adjusted by

placing
tapered shims or
wedges
between
the
springs and spring seats. For
complete
information

regarding
the steering
geometry
refer to the
Section O.

M-16.
Removal of Solid
Front
Axle

Note:
The procedure for removing the solid front
axle varies slightly, depending on whether the
springs are slung under or over the axle. These

variations
are
noted
in the following procedure.

a. -
Raise the front end of the vehicle and safely support the frame behind the springs.

b.
Remove the
wheels
by removing the wheel
discs and lug nuts.

c.
Disconnect the steering connecting rod at the
ball
and socket connection on the steering knuckle. 282

o

STEERING
SYSTEM
10

FIG.
0-7—STEERING
CONNECTING
ROD
(DRAG
LINK)
10696

1—Cotter Pin

2>—Large
Plug

3—
Ball
Seat

4—
Ball
Seat Spring 5—
Spring
Plug
shaft,
tightness
of the steering gear in the frame,

tightness
of steering gear arm, adjustment of the
steering connecting rod and condition of the steer­ ing tie rod
ball
joint ends. Adjust the steering con­
necting rod (drag
link)
to maximum safe
tightness

at both ends. Examine the steering beilcrank bearings, the shaft in the mounting bracket, and
the mounting bracket on the frame cross member,
k.
Check
front axle caster.
This
should be the same
on both sides, otherwise a locking brake may be

indicated
causing a twisting action of the axle.
Correct
caster is shown in specifications at the end
of this section.

I.
Check
the front wheel toe-in. See Specifications,

m.
Check
wheel
toe-out
on turns.
This
gives
you

an
indication of the proper angularity of the steer­
ing knuckle arms and tells whether or not they have been bent and require replacing. These may be checked by comparing them with new parts. If

an
arm is bent, check for a bent tie rod.
n.
Check
wheel camber.
This
should be the same
on both wheels as shown on the Specifications,

o.
Check
the king pin inclination. See Specifica­ tions.

p.
Check
the tracking of the front axle and frame
alignment, which may be incorrect due to an accident.

0-14.
STEERING
LINKAGE
SERVICE
The
steering linkage must maintain constant toe-
in
and
good
steering control under all driving
conditions.
This
requires
ball
joints at each end
of the tie rods and steering connecting rod. All
joints in the steering linkage must be kept well
lubricated
for easy operation and long life. Should
the joints be worn, allowing excessive free motion
in
the linkage, the joints must be replaced. When­
ever
ball
joints are replaced, toe-in must be reset. Because
some
members of the steering system may
have
become
bent or distorted, a periodic inspection
should be made.
0-15.
Steering Connecting
Rod
(Drag
Link)

The
steering connecting rod is of the
ball
and socket
type. All
ball
seat springs and adjusting plugs are 6—
-Dust
Cover

7—
Dust
Shield
8—
Small
Adjusting Plug
9—
Lubrication
Fitting
10—Connecting Rod

identical,
the only difference
between
front and
rear
end being the relative location of the springs.

The
correct assembly of the steering connecting
rod
is shown in Fig. 0-7. At the front or axle end,
the spring and spacer are assembled
between
the
rod
and
ball
seat, while at the steering gear end,
spring
and spacer are
between
the
ball
seat and the
end plug. In the illustration the front end is to the left.

When
removing springs and
seats
for any reason,
make
sure they are reassembled as shown in the

illustration
because this method of assembly re­
lieves road shock from the steering gear in both di­
rections. To adjust the
ball
joint, screw in the plug

firmly
against the
ball,
approximately 20 ft. lb. [2,8 kg-m.] then back off one quarter
turn
and lock

with
a new cotter pin inserted through
holes
in the
tube and the slot in the adjusting plug. To adjust the
ball
joint at the steering gear arm, screw in the end plug firmly against the
ball,
then back off one

full
turn
and lock with a new cotter pin inserted
through
holes
in the tube and the slot in the ad­

justing
plug.

The
above adjustments
will
give
the proper spring
tension and avoid any
tightness
when swinging
the wheel from maximum left to right
turn.
The
ball
joints must be tight enough to prevent end

play
and yet
loose
enough to allow free movement.
0-16. Tie Rod
The
tie rods are of three piece construction con­sisting of the rod and two
ball
and socket end as­ semblies.
Ball
and socket end assemblies are
threaded into each rod and locked with clamps,

around
each end of the rod. Right and left hand threads on tie rod end assemblies provide toe-in adjustments without removing the tie rod ends from
the steering arm.

'Jeep'
Universal models are equipped with a

divided
tie rod connected to a bell-crank mounted
on the frame cross member.
With
this type con­

struction
the toe-in of each wheel is adjusted in­
dependently. See heading "Toe-in adjustment".

When
wear takes place in the tie rod end
ball
and socket, it
will
be necessary to replace the
ball
and socket assembly and also the rubber seal. 318

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

P
f. On vehicles without a transmission brake hold
the brake
shoes
in their relative position and
engage
the parking brake cable
into
the parking

brake
lever.
g. On vehicles without a transmission brake in­
stall
the parking brake strut and spring
between

the parking brake lever and the primary
shoe.

h.
Place the brake
shoes
on the backing plate and

install
the retainer pins, springs and retainers.

i.
Install the anchor pin plate.

j.
Install the lever and
sleeve
on the primary
shoe
then install the secondary return spring, then the
primary
return spring.

Important:
A
"L"
or "R" is located on the hex­

agon
side of the lever crank for identification. The
lever crank marked "R" applies to the primary
shoe
on the
left
rear brake assembly. The lever
crank
marked
"L"
applies to the primary
shoe
on
the right rear brake assembly.
k. Place the upper linkage rod in the
groove
of the
anchor pin and
engage
the hook of the link rod
into

the adjusting lever.

I.
Install the brake drum. Install the wheel and

tire
assembly.
m. Adjust the brakes as described
below.

P-19.
Brake
Shoe
Initial
Adjustment —

a.
Should wheel brake units have
been
disassem­ bled for any reason, an initial adjustment
MUST
be made
before
drum installation.

b.
When the brake parts have
been
installed in
their correct position, initially adjust the adjusting
screw assemblies to a point where approximately Y% [9,53 mm.] of threads are
exposed
between
the

star
wheel and star wheel nut.

Note:
Following the initial adjustment and final
assembly, check brake pedal height to ensure

brake
operation. Then drive the car in reverse and
FIG.
P-12—BRAKE SHOE ADJUSTMENT
1—
Star
Wheel
2—
Lever

3—
Screwdriver
4—
Brake
Adjusting Tool
forward,
making 10 to 15 brake applications prior
to road testing.
This
action balances the adjust­
ment of the four brake units and raises the brake
pedal.
c. Adjustment may be made manually by remov­ing the access
slot
cover and using a brake adjust­
ing
tool
or screw driver to rotate the star wheel
until
the wheel is in the locked position. To tighten, rotate the star wheel in the clockwise direction.
Then
back off the star wheel at least 15 to 20

notches
(clicks).

d.
To back off the star wheel on the brake, insert
ice pick or thin blade screw driver in adjusting screw
slot
to hold lever away from adjusting screw.

Back
off on adjusting screw until wheel and drum

turn
freely. Replace adjusting
hole
cover.

Caution:
DO NOT attempt to back off on ad­
justing screw without holding adjuster lever away from screw as adjuster
will
be damaged.
P-20. Master Cylinder Reconditioning —
Dual
System

Refer
to Fig. P-13.

DISASSEMBLY
a.
Remove the filler cap and empty all fluid.
b.
Remove the snap ring, push rod assembly, and
the primary and secondary piston assemblies. Air pressure applied in the piston
stop
hole
will
help
facilitate the removal of the secondary piston as­
sembly.
c. The residual check valves are located under
the front and rear fluid
outlet
tube
seats.

d.
The
tube
seats
must be removed with the
self-

tapping screws supplied in the repair kit to permit removal of the check valves. Screw the self-tapping
screws
into
the
tube
seats
and place two screw

driver
tips under the screw head and force the
screw upward as shown in Fig. P-14.
e. Remove the expander in the rear secondary cup, secondary cups, return spring, cup protector,
pri­

mary
cup, and washer from the secondary piston.
f. The primary piston, with the rubber cups in­ stalled, is supplied in the repair kit.

CLEANING
a.
After disassembly, immersion of all metal parts
in
clean brake fluid or a brake system cleaner is
recommended. Use air
hose
to blow out dirt and cleaning solvent from recesses and internal pas­

sages.
When overhauling a hydraulic brake unit,
use all parts furnished in the repair kit. Discard
all
old rubber parts.

b.
After cleaning, place
all"
hydraulic
system parts
on clean paper or in a clean pan.

INSPECTION
Inspect all other parts for damage or
excessive

wear.
Replace any damaged, worn, or chipped
parts.
Inspect hydraulic cylinder bore for
signs
of
scoring, rust, pitting, or etching. Any of
these
will
require
replacement of the hydraulic cylinder. 331

BRAKES

12519

FIG.
P-13—DOUBLE
SAFETY MASTER CYLINDER
1— Boot
2— Snap Ming 3"*—Piston Assembly
4—
Backing
Ring 5—
Master
Cylinder Cup 6—
Master
Cylinder Cup
7— Piston
8—
Master
Cylinder Cup 9—
Cup
Protector
10—Spring 11—
Cylinder
Housing
12—
Cover
Gasket
13—
Cover

14—
Washer
Gasket 15—
Washer
16—
Cover
Bolt
17—
Check
Valve Spring 18—
Check
Valve
19—
Tube
Seat
20— Piston Stop
REASSEMBLY

a.
Prior
to reassembly of the master cylinder, dip

all
components
in clean brake fluid and place on
clean paper or in a clean pan.

b.
Install the primary cup washer, primary cup,
cup protector, and return spring on the secondary piston.
c. Install the piston cups in the double
groove
end
of the secondary piston, so the flat j of the cups face each other (lip of cups away from each other).
Install
the cup expander in the lip
groove
of the
end cup.

cL
Coat the cylinder bore and piston assemblies with clean brake fluid
before
installing any parts

in
the cylinder.
e. Install the secondary piston assembly first and then the primary piston which is supplied in the
repair
kit.

f.
Install the push rod assembly, which includes
the push rod,
boot,
and rod retainer, and secure
with the snap ring. Install the primary piston
stop.

g. Place new rubber check valves over the check valve springs and install in the
outlet
holes, spring
first.

Note:
When replacing a
complete
master cylinder
with a service unit, the original push rod must be used. The push rod retainer and snap ring retainer 12617

FIG.
P-14—REMOVING TUBE SEATS 1
—Screwdriver

2— No. 6-32 Self-Tapping Screw

3—
Tube
Seat must be removed and discarded. As the new unit
has the retainers installed it is only necessary to

install
the push rod until a "snap" is heard and the push rod is retained. 332

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P h.
Install
the tube seats, flat side toward the check

valve,
and press in with tube nuts or the master

cylinder
brake pipe tube nuts.

BLEEDING
a.
Before the master cylinder is installed on the
car,
the unit must be bled.

b.
Support the cylinder assembly in a vise and

fill
both fluid reservoirs with approved brake fluid,

e.
Loosely install a plug in each
outlet
of the

cylinder.
Depress the push rod several times until

air
bubbles cease to appear in the brake fluid.

d.
Tighten the plugs and attempt to depress the piston. The piston travel should be restricted after
all
air is expelled.
e.
Install
the master cylinder on the car and bleed
the hydraulic lines at the wheel cylinder. Refer to
Par.
P-7.

P-21.
Wheel
Cylinder
Reconditioning
•
Refer to Fig. P-15.
Note:
Make sure a replacement brake cylinder
has the same part number as the original cylinder.

FIG.
P-15—WHEEL
BRAKE CYLINDER
1— Boot

2—
Piston

3—
Cylinder
Cup
4—
Cup
Spring
5—
Cylinder

6—
Bleeder
Screw
a.
To remove a wheel cylinder,
jack
up the vehicle

and
remove the wheel, hub, and
drum.
Disconnect
the brake line at the fitting on the brake backing
plate. Remove the brake
shoe
return spring which

will
allow the brake
shoes
at the toe to
fall
clear of the brake cylinder. Remove two screws holding
the wheel cylinder to the backing plate.
b.
Remove the rubber dust covers on ends of

cylinder.
Remove the pistons and piston cups and
the spring.

c.
Wash the parts in clean alcohol.

d.
Examine the cylinder bore for roughness or
scoring.
Check
fit of pistons to cylinder bore.
e. When reassembling the cylinder, dip springs, pistons and piston cups in brake fluid.
Install

spring
in center of the wheel cylinder.
Install

piston cups with the cupped surface towards the

spring
so that the flat surface
will
be against
the piston.
Install
pistons and dust covers.
f.
Install
wheel cylinder to the backing plate and connect brake line and install brake
shoe
return

spring.

g. Replace wheel, hub, and
drum.

h.
Bleed the brake lines (Par. P-7).

P-22. TROUBLE
SHOOTING

P-23.
Squeaky
Brakes

In
most cases, squeaks are entirely eliminated by

correct
adjustment of the brakes. Squeaks may be
caused however, by glazed linings, lining wore thin
to the point of
exposed
rivets or by vibration. A

drum
will
not vibrate when the brake is securing

uniform
contact over the entire lining surface, ex­
cept when due to improper conditions such as the
linings becoming glazed.
Glazed
surface of the

brake
linings may be removed by a stiff
wire
brush.
Occasionally
squeaks are caused by roughened
sur­

face of the
drum,
which can usually be remedied
by rubbing down with emery cloth and by wiping
the brakings surface clean. In extreme cases it may
be necessary to reface the drum in a lathe. Should
this be done, do not remove a metal thickness greater than .030" [0,762 mm.] - .060" [1,52 mm.]

overall
diameter.

P-24. Rattles
in
Brakes

See that the tension of the springs in the brakes

and
attached to the control system are sufficient to

return
brakes and brake mechanism to their normal
position.
Return
springs are so placed that they
keep all slack out of the control system by tension on all joints.

Brakes
will
not rattle inside the
drum
if the springs
holding the
shoes
are kept at the proper tension. 333

ALPHABETICAL
INDEX

SUBJECT
PAR.

SUBJECT
PAR.

Ignition Cable Test C-l9 Ignition
Coil
C-20, H-19, H-31
Ignition Switch H-89 Ignition System H-3
Ignition
Timing
C-14, H-18, H-30 Ignition Wires C-18
Intake Manifold '." Dl-7, Dl-101
Instrument, Electrical H-122

L

License Plate Light H-l36
Lighting
System H-l25

Light
Switch, Main . H-l 26

Lubrication
B-l
Lubrication,
Body B-65

Lubrication
Maintenance Schedule B-8
Lubrication
of Optional Equipment B-69

Lubrication,
Off Highway B-79

Lubrication,
Special. B-2

M

Main
Bearings D-43, D-82, Dl-32, Dl-42, Dl-73

Main
Light Switch. H-l26
Maintenance, Clutch 1-2 Maintenance, Exhaust System.,
-
F-4
Manifold, Exhaust -F-6 Manifold, Intake D-7, Dl-101
Manifold Vacuum Check. .C-24 Master Cylinder, Brake B-40, P-2, P-20
Miscellaneous Data U-16 Mountings, Engine • • •
-
D-3, Dl-3
Muffler. F-9

O
Oil
Filter B-10, B-ll,
D-lll,
Dl-13, Dl-93

Oil
Pan D-19, D-66, D-97, Dl-29, Dl-51, Dl-77
Oil
Pump. D-14, D-65, D-93, Dl-19, Dl-50, Dl-87

P

Paint and
Trim
Plate • • A-7

Parking
Brake Adjustment P-ll
Parking
Lights H-133
Pilot Bushing, Crankshaft D-70, 1-8
Pintle Hook U-7
Pistons D-20, D-95, Dl-31, Dl-48, Dl-75 Piston Rings. • • •
•
D-37, Dl-47 Positive Crankcase Vent. B-13, C-6, D-110

Powr-Lok
Differential B-72, N-20
Primary
Circuit,
Electrical H-4 Propeller Shaft U-Joints .B-58, L-2, L-3 Propeller Shaft Specifications <:' L-7

R

Radiator
B-28, B-29, G-5

Radiator
Hoses. G-7

Radiator
Pressure Cap G-4

Rear
Axle. B-50, B-51, B-52, N-9

Rear
Axle Reassembly • N-l
7
Rear
Axle Disassembly N-l
2

Rear
Axle Pinion Adjustment N-l6

Rear
Axle Shaft N-2, N-3

Rear
Bearing Seal, Crankshaft D-63, D-85, Dl-62

Rear
Wheel Bearings B-56, B-57, N-4, Q-3
Regulator Test, Voltage H-47, H-71
Rocker
Arm Cover.. . Dl-65

Rocker
Arms D-16, D-74, D-99, Dl-60 Rotor, Alternator H-76, H-79

S

Seats
• T-8 Secondary
Circuit,
Electrical H-5
Shock Absorbers B-48, S-7
Solenoid Switch. H-l21 Special Lubricants B-2
Spark
Plugs C-4, H-33
Special Tools • U-ll

Speedometer
Cable B-60 Springs B-77, S-4, S-5

Spring
Bushings S-2

Spring
Pivot Bolts S-3

Spring
Shackles S^2

Spring
Specifications S-8 372 Starting Motor B-18, H-92, H-108
Starting Motor Bearings B-75
Starting Motor Bendix Drive H-105, H-106
Starting System H-7, H-88
Starting System Maintenance H-93 Stator, Alternator H-84
Steering • • •
•
O-l
Steering Arm P-10
Steering Column Adjustments 0-4
Steering Column and Wheel Service O-20 Steering Gear. . B-27, 0-22
Steering Gear Adjustment 0-5
Steering Gear Function 0-2
Steering Knuckle. B-27, M-8 Steering Linkage 0-14

Stop
Light Switch H-128
Switch, Heater U-10 Switch, Ignition H-89
Switch, Wiper Motor H-142

T

Tail
Light . H-134

Tail
Pipe F-10 Temperature Sending Unit G-10
Thermostat G-9
Timing
Chain Dl-22, Dl-66, Dl-84
Timing
Chain Cover Dl-20, Dl-67, Dl-86
Timing
Gears D-22, D-54, Dl-22, Dl-66, Dl-84

Timing,
Ignition. C-14, H-18, H-30

Tire
Service . •
•
Q-l
1

Toe-in Adjust 0-7, 0-8 Tools, Special. . .
........
U-ll Torque Specifications, Chassis U-14
Torque Specifications, Engine .U-13

Top,
Canvas. T-5

Trac-Lok
Differential N-24
Transfer
Case B-36, K-1
Transfer
Case Reassembly K-6

Transfer
Case Disassembly K-3

Transfer
Case Linkage - K-8

Transfer
Case Removal K-2 Transmission and Transfer Case. B-30, J-7 Transmission —
3-Speed
B-37, B-38, J-l
Transmission —
4-Speed
... J-20
Transmission Brake P-4 Transmission Brake Adjustment P-l
2

Transmission,
Cane Shift .J-8 thru J-19

Transmission,
Remote Shift J-4
Transmission Remote Shift Adjustment J-3
Transmission Specifications
-
J-27
Tune-Up
Sequence
C-2

Tune-Up
Specifications C-30

U

U-Joint, Front Axle . . B-54, B-55, M-7
U-Joint, Propeller Shaft B-58, L-l

Vacuum
C-24 Valves D-21, D-56, D-90, Dl-56, Dl-63

Valve
Adjustment D-107

Valve
Lifter Dl-57, Dl-81

Valve
Seats
D-59

Valve
Springs .D-56, D-90, Dl-63

Valve
Tappets C-8, D-29, D-62, D-80
Valve
Timing D-109
Vehicle Description A-2
Vehicle Identification A-3
Vehicle Serial Number. A-5

Vibration
Damper D-l2, D-96, Dl-17, Dl-70 Voltage Regulator. H-41, H-71

W

Water Pump G-ll thru G-15
Water Pump Bearings B-74
Wheels Q-l
Wheel Balancing Q-2 Wheel Bearing Adjustment Q-5, Q-6, Q-7
Wheel Brake Service P-6 Wheel Bearing Service Q-3
Wheel Cylinder, Brake P-21 Windshield T-3 Windshield Wiper Motor . .H-142

SM-1046
PRINTED
IN U.S.A.
110-CH6M