1953 JEEP DJ fuel pressure

'Jeep*
UNIVERSAL SERIES
SERVICE
MANUAL

D
insulator
mountings attached to the frame side

rail
brackets. The
rear
of the engine-transmission
assembly is supported by a rubber insulator
mounting under the
rear
of the transmission on
the frame center cross member.
This
cross member
is bolted to the frame side
rails
so that it can be
dropped when removing the transmission or engine-

transmission
assembly. The rubber insulators allow
free side and vertical oscillation to effectively

neutralize
engine
vibration at the source.

The
rubber
insulator mountings should be inspected
for separation and deterioration by jacking the
power plant away from the frame, near the sup­
ports. Vibration cannot be effectively absorbed by
separated or worn insulators. They should be re­ placed if faulty.

D-4.
Engine
Ground
Strap

To
be sure of an
effective
ground for the electrical

circuits,
a ground strap bridges the right front

engine
support to the chassis. The connections of this strap must be kept clean and tight for proper
operation of the electrical system.

D-5. ENGINE REMOVAL

Should
the
engine
require overhauling, it is neces­

sary
to remove it from the vehicle. The following procedure covers removal of the
engine
only.

The
engine, transmission and transfer case may be
removed as a unit by removing (in addition to the following procedure) the radiator guard and the
access plates in the floor pan.

a.
Drain
the cooling system by opening the
drain
cocks at the
bottom
of the radiator and lower right
side of the cylinder block.

b.
Disconnect the battery at the positive terminal
to avoid the possibility of short
circuit.

c. Remove the air cleaner horn from the carburetor
and
disconnect the breather
hose
at the oil filler
pipe.

d.
Disconnect the carburetor choke and throttle controls by loosening the clamp
bolts
and set
screws.

e. Disconnect the fuel-tank-to-fuel-pump line at the fuel pump by unscrewing the connecting nut.
f- Plug the fuel line to prevent fuel leakage.
g. Remove the radiator and radiator grille support

rods.

h. Remove the upper and lower radiator
hoses
by
loosening the
hose
clamps and slipping the clamps
back
on the
hose.
If so equipped, remove the heater

hoses
(one to the water pump, one to the
rear
of
the cylinder head) in the same manner.

i.
Remove the four
bolts
from the fan hub and re­

move
the fan hub and fan blades.

j.
Remove the four radiator attaching screws. Re­
move
the radiator and shroud as one unit, k. Remove the starting motor cables. Remove the

starting
motor.

I.
Disconnect the wires from the alternator or
generator. Disconnect the ignition
primary
wire
at the ignition coil.
NOTE:
ON
ENGINES EQUIPPED WITH EX­

HAUST
EMISSION CONTROL, REMOVE THE
AIR
PUMP,
AIR
DISTRIBUTION
MANI­
FOLD,
AND
ANTI-BACKFIRE (DIVERTER)

VALVE.
SEE SECTION
Fl
FOR PROCEDURE.
m.
Disconnect the oil pressure and temperature
sending unit wires at the units.

n.
Disconnect the exhaust pipe at the exhaust
manifold by removing the stud nuts.

o.
Disconnect the
spark
plug cables at the plugs

and
remove the cable bracket from the rocker arm cover stud.

p.
Remove the rocker arm cover by removing the
attaching stud nuts.

q.
Attach a lifting bracket to the
engine
using
existing head bolt locations. Be sure the
bolts
selected
will
hold the
engine
with the weight

balanced.
Attach lifting bracket to a boom hoist,

or
other lifting device, and take up all slack,
r.
Remove the two nuts and
bolts
from each front

engine
support. Disconnect the
engine
ground strap.
Remove the
engine
supports.
Lower
the
engine
slightly to permit access to the two top
bolts
on
the flywheel housing.
s. Remove the
bolts
which attach the flywheel
housing to the engine.

t.
Pull
the
engine
forward, or
roll
the vehicle back­

wards,
until the clutch clears the flywheel housing.

Lift
the
engine
from the vehicle.

D-6. ENGINE DISASSEMBLY

Engine
disassembly is presented in the sequence to be followed when the
engine
is to be completely
overhauled after removal from the vehicle. Some
of the operations of the procedure are also ap­
plicable
separately with the
engine
in the vehicle,

provided
that wherever necessary the part of the

engine
to be worked on is first made accessible by
removal
of
engine
accessories or other parts.

When
the disassembly operations are performed

with
the
engine
out of the vehicle, it is assumed,
in
this procedure, that all of the accessories have been removed
prior
to starting the disassembly

and
the oil has been drained.
In
addition to the instructions covering operations
for disassembling the
engine
out of the vehicle,

special
instructions are given to cover different
operations required when disassembly is
done
with the
engine
installed.

During
disassembly operations, the
engine
should
be mounted in a suitable
engine
repair
stand. Where

practicable,
modify or adapt an existing repair

stand
as necessary to accommodate the engine. If

an
engine
repair stand is not used, take care to

perform
disassembly operations in a manner that

will
protect personnel against an accident and the
engine
and its parts against damage.

NOTE:
If the
engine
is being disassembled because
of possible valve failure, check the valve tappet
clearance
before disassembly. Improper valve

clearance
could be the possible cause of valve

failure,
indicating a need for more frequent valve
checks and adjustments. 41

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

D
satisfactory bearing replacement cannot be made

and
it
will
be necessary to regrind the crankshaft.

Install
the bearing lower
half
and the connecting

rod
cap and draw the cap bolt nuts down equally
and
only slightly tight. Move the connecting rod
endwise, one way or the other, on the crankshaft to be sure the bearing is not tight.
Pull
the nuts tighter, first one then the other, a little at a time,

and
keep trying the fit of the rod on the crankshaft by hand until the recommended torque of 35 to 45 lb-ft. [4,8 a 6,2 kg-m.] is reached. If the
bearings are of the correct size, and have been
properly
lubricated with light
engine
oil before in­

stallation,
the connecting rod should be easy to
slide back and forth parallel to the
crankpin.
If
the connecting rod is tight on the crankshaft, a

larger
bearing is required. If there is no binding

or
tightness, it is
still
necessary to check clearance
to guard against too
loose
a fit. The use of "Plasti­

gage"
or shim stock of the proper size to measure .001" [0,025 mm.] clearance is recommended for

checking
connecting rod bearing clearances.
This

is the same material recommended for checking
crankshaft
main bearings and the method of check­
ing is
similar.
Refer to
Par.
D-45 or D-46. Connect­
ing rod bearings are fitted to the same clearance as the main bearings but the torque specified for con­
necting rod cap
bolts
is different.

D-50.
Connecting
Rod
Side Play

Check
the connecting rod side play with a feeler
gauge
as shown in Fig. D-l8. The side clearance is .004" to .010"
[0,101
a
0,254
mm.].

D-51.
Camshaft and Bearings

The
camshaft is supported at four points in the

cylinder
block. The front is supported in a re­ placeable, steel-shell, babbit-lined bearing. The

bearing
is pressed into place The other three bear-
FIG.
D-18—CONNECTING
ROD
SIDE
PLAY
ing surfaces are precision machined in the cylinder
block. The camshaft bearings are pressure
lubri­

cated through drilled passages in the crankcase.

End
thrust of the camshaft is taken by a thrust plate bolted to the crankcase. The camshaft is

driven
by a silent helical-cut
tooth
timing gear at
the front of the engine. A worm gear, integral with
the camshaft, drives the oil pump and distributor.

The
fuel pump is actuated by an eccentric forged

onto
the camshaft.

Clean
the camshaft thoroughly in cleaning solvent.
Inspect
all camshaft bearing surfaces to determine

if
they are scored or rough. The cam faces must be
perfectly smooth throughout their contact face

and
must not be scored or worn.

D-52.
Camshaft
Front Bearing Replacement

Use
a suitable driver to remove the camshaft front
bearing
from the cylinder block. To install a new
bearing,
align the oil
hole
in the bearing with the
bored oil
hole
in the cylinder block and drive the

bearing
in until the front end of the bearing is

flush
with the front surface of the cylinder block.

Make
sure the oil
hole
is open and clear. It is not
necessary to line-ream the bearing after installation because bearings for replacement are precision
reamed
to the finished size. Do not stake the

bearing.

D-53-
Camshaft End Play

End
play of the camshaft is determined by running
clearance
between
the
rear
face of the camshaft gear and the thrust plate and is established by the

spacer
thickness. The standard clearance is .004"
to .007"
[0,101
a 0,178 mm.] and can be measured by a
dial
indicator. As a general rule this clearance

will
change but little through wear or when a new gear is installed. To predetermine the correct end
float with the gear, spacer, and thrust plate re­
moved, measure the thickness of both the thrust
plate and spacer with a micrometer. The thickness
of the spacer should be approximately .006" [0,152 mm.] greater than that of the thrust plate.

When
this is correct and the parts are assembled

and
drawn tightly
together
by the gear retaining

screw,
the end play should
come
within standard
limits.

D-54.
Timing Gears
and
Cover

The
timing gears are mounted at the front of the
engine. Camshaft drive is through helical-cut
timing gears; a steel gear on the crankshaft and a
pressed fiber gear on the camshaft. The gears are keyed to their respective shafts. The camshaft

driven
gear is secured on the front end of the
camshaft by means of a capscrew and a plain

washer.
The crankshaft gear is secured on the
front end of the crankshaft by a nut threaded
onto
the front end of the crankshaft holding the
crank­

shaft pulley, crankshaft oil slinger, and the
crank­

shaft drive gear spacer. The timing gears are

lubricated
through a jet threaded into the
crank­
case directly above the gear contact and oil supplied
through a drilled passage from the front main

bearing.
The timing gears are enclosed by the
sealed timing cover. The oil seal in the cover bears 53

D
HURRICANE
F4
ENGINE
D-101.
Install
Manifold

If
manifold studs were removed for replacement,
apply sealer on the stud threads
before
installing
a
new stud.
See Section Fl for exhaust emission controlled

engines.
Make
certain that no foreign objects are inside the manifold and that all
passages
are clear. Place a
new set of manifold
gaskets
in position on the side
of the cylinder block.
Then,
carefully slide the manifold
onto
the studs and against the cylinder block being careful not to damage the gaskets.
Torque
all manifold attaching nuts evenly 29 to
35 lb-ft. [4,0 a 4,8 kg-m.].
D-102.
Install
Oil
Filler
Tube

When
installing the oil filler tube, be sure that the
beveled lower end is away from the crankshaft.
Place a
piece
of
hard
wood
over the top of the
tube

to prevent damage to the cap gasket seat.
D-103.
Install
Water Pump

Make
certain that the mating surfaces of the water pump and the cylinder block are clean and smooth.
Install
the gasket on the
flange
of the pump and

install
the pump in position on the cylinder block.
Torque
the water pump attaching
bolts
alternately

and
evenly 12 to 17 lb-ft. [1,7 a 2,3 kg-m.].
D-104.
Install
Water Outlet Fitting

Install
the thermostat and the water
outlet
fitting.
Torque
the water
outlet
fitting attaching
bolts
20
to 25 lb-ft. [2,8 a 3,4 kg-m.].
FIG.
D-42—INSTALLING HURRICANE F4 ENGINE
IN
VEHICLE

1—
Lifting
Sling
2— Hoist
Cable

3—
Hurricane
F4 Engine
4— Dowel Bolt
5—
Flywheel
Housing
D-105.
ENGINE INSTALLATION
a.
Install
lifting sling to
engine
and using suitable hoist raise the
engine
from its blocking or stand

and
then slowly lower it
into
the
engine
compart­ment of the vehicle.

Note:
When installing the
Hurricane
F4 Engine,
two % x 4 inch
guide
bolts
or
dowels
should be
used to properly
guide
and align the
engine
to the
flywheel housing (See Fig. D-42).
b. Slightly tilt the
engine
downward and at the
same time slide the
engine
rearward
while lining up the transmission main gear shaft with the clutch
throw-out bearing and disc spline.

Note
:The
engine
crankshaft may have to be turned
slightly to align the transmission main gear shaft
with the clutch disc spline.
c. Remove the
guide
bolts
or
dowels
and secure
the
engine
to the housing.

d.
Secure the front
engine
mounts to the frame brackets and
bolt
ground cable to
engine.

e. Remove lifting sling from
engine.

f. Connect exhaust pipe to
engine
manifold flange.
g. Connect throttle and choke cables to carburetor.
h.
Install
fan to water pump pulley.
i.
Connect fuel pump line to main fuel line,

j.
Replace starting motor assembly. k. Connect
engine
wiring harness connectors at
front of cowl.

I.
Connect wires to starting motor assembly, water
temperature and oil pressure sending units and alternator.

NOTE:
ON
ENGINES EQUIPPED WITH EX­

HAUST
EMISSION CONTROL,
REPLACE
THE
AIR
PUMP,
AIR
DISTRIBUTOR
MANI­

FOLD,
AND
ANTI-BACKFIRE (DIVERTER)
VALVE.
SEE
SECTION
Fl.
m. Replace radiator and radiator grille support
rods and connect coolant
hoses
to
engine.

Note:
Replace heater
hoses
if vehicle is equipped
with hot water heater.

n. Fill
radiator with coolant and
engine
with oil
(see
Lubrication
Chart).

o.
Install
air cleaner and connect carburetor air
hose.

p. Connect battery cables and start
engine,

q.
Install
hood
and road
test
vehicle.
D-103.
FINAL
IN-VEHICLE
ADJUSTMENTS
a.
Clean
battery terminals and check battery. b.
Check
ignition terminals and check battery.
c. Service carburetor air cleaner.

d.
Service positive crankcase ventilation valve.
e.
Check
fuel lines. f. Gap and install new
spark
plugs.
g.
Check
distributor
points
and capacitor; replace
if
necessary. 68

D

HURRICANE
F4
ENGINE
D-112.
SERVICE
DIAGNOSIS

Poor
Fuel
Economy Ignition Timing Slow or Spark Advance Stuck

Carburetor
Float High
Accelerator Pump Not Properly Adjusted
High
Fuel
Pump Pressure

Fuel
Leakage
Leaky
Fuel
Pump Diaphragm
Loose Engine Mounting Causing High
Fuel
Level

in
Carburetor

Low
Compression Valves Sticking

Spark
Plugs Bad

Spark
Plug Cables Bad Weak
Coil
or Condenser Improper Valve Tappet Clearance

Carburetor
Air Cleaner Dirty
High Oil Level in Air Cleaner Dragging Brakes

Front
Wheels Out of Alignment
Tires
Improperly Inflated Inaccurate Odometer

Faulty
Fuel
Tank
Cap

Clogged
Muffler or Bent Exhaust Pipe

Lack
of Power
Low
Compression Ignition System (Timing Late)
Improper Functioning Carburetor or
Fuel
Pump

Fuel
Lines
Clogged
Air
Cleaner Restricted
Engine Temperature High Improper Tappet Clearance
Sticking Valves Valve Timing Late

Leaky
Gaskets
Muffler
Clogged
Bent Exhaust Pipe

Defective
Spark Plugs—Clean or Replace
Defective
Breaker Points—Replace
Points

Incorrect Breaker Point Gap—Reset
Points

Defective
Condenser or Coil—Replace
Loose Electrical Connections—Locate and Tighten
Broken Valve Spring—Replace Spring Broken Piston or Rings—Replace
Defective
Head Gasket—Replace Gasket
Cracked
Distributor Cap—Replace Cap

Low
Compression
Leaky
Valves
Poor Piston Ring Seal Sticking Valves
Valve Spring Weak or Broken
Cylinder
Scored or Worn
Tappet Clearance Incorrect
Piston Clearance too Large
Leaky
Cylinder Head Gasket
Burned Valves and
Seats
Sticking Valves or too Loose in Guides Improper Timing
Excessive Carbon Around Valve Head and Seat Overheating
Valve Spring Weak or Broken Burned Valves and Seats—Continued
Valve Tappet Sticking
Valve Tappet Clearance Incorrect
Clogged
Exhaust System
Valves Sticking Warped Valve Improper Tappet Clearance
Carbonized or Scored Valve
Stems
Insufficient Clearance Valve Stem to Guide
Weak or Broken Valve Spring Valve Spring Cocked Contaminated Oil
Overheating Inoperative Cooling System
Thermostat Inoperative Improper Ignition Timing
Improper Valve Timing
Excessive Carbon Accumulation

Fan
Belt too Loose

Clogged
Muffler or Bent Exhaust Pipe

Oil
System Failure
Scored or Leaky Piston Rings

Popping-Spitting-Detonation
Improper Ignition
Improper Carburetion
Excessive Carbon
Deposit
in Combustion
Cham­
bers
Poor Valve Seating Sticking Valves
Broken Valve Spring Tappets Adjusted too Close

Spark
Plug Electrodes Burned
Water or Dirt in
Fuel
Clogged
Lines Improper Valve Timing
Excessive Oil Comsumption Piston Rings Stuck in Grooves, Worn or Broken Piston Rings Improperly Fitted or Weak Piston Ring Oil Return
Holes
Clogged
Excessive Clearance, Main and Connecting Rod
Bearings

Oil
Leaks at Gaskets or Oil Seals
Excessive Clearance, Valve Stem to Valve Guide (Intake)

Cylinder
Bores Scored, Out-of-Round or Tapered Too Much Clearance, Piston to Cylinder Bore
Misaligned Connecting Rods
High Road
Speeds
or Temperature
Crankcase
Ventilator Not Operating
Bearing Failure
Crankshaft
Bearing Journal Out-of-Round

Crankshaft
Bearing Journal Rough

Lack
of Oil
Oil
Leakage
Dirty
Oil

Low
Oil Pressure or Oil Pump Failure
Drilled
Passages
in Crankcase or Crankshaft
Clogged

Oil
Screen Dirty Connecting Rod Bent 70

'Jeep'
UNIVERSAL SERIES
SERVICE
MANUAL

Dl

DAUNTLESS
V-6
ENGINE
Contents

SUBJECT
PAR.
SUBJEC

GENERAL
.... . . Dl-1 Oil Pump Cl(
ENGINE DESCRIPTION
D1-2

Engine
Mounts Dl-3

ENGINE REMOVAL
Dl-4
ENGINE DISASSEMBLY
Dl-5
Alternator
and Fan Belt Dl-11
Camshaft
.... Dl-26
Cooling Fan and Water Pump.
......
.Dl-12
Crankshaft
Front Oil Seal .Dl-21

Crankshaft
Pulley D1-17
Crankshaft
Vibration Damper Dl-18

Cylinder
Head Assembly Dl-24

Distributor
Dl-9
Exhaust
Manifold .Dl-8

Flywheel
Dl-28

Flywheel
Housing and
Clutch
Dl-27
Fuel
Pump. ... . .Dl-10
Intake
Manifold and
Carburetor
Assembly.
.............
.Dl-7

Main
Bearing and Crankshaft. Dl-32 Mounting Engine on Engine Stand. . . . .Dl-6

Oil
Dipstick. Dl-16
Oil
Filter
Dl-13
Oil
Pan.. ...
.......
.Dl-29
Oil
Pressure Sending Unit Dl-15

Oil
Pump Dl-19
Oil
Pump Intake Pipe and Screen Dl-30
Piston and Rod Assembly. Dl-31
Push
Rod and Valve
Lifter.
.Dl-25
Rocker
Arm Cover Dl-23
Starter
Motor Dl-14

Timing
Chain
and Sprocket Dl-22
Timing
Chain
Cover Dl-20

ENGINE CLEANING, INSPECTION AND REPAIR
. . ... .Dl-33
Camshaft
Cleaning and Inspection Dl-55
Connecting Rod Bearing Inspection
and
Fitting .Dl-49

Crankshaft
Cleaning Dl-38
Crankshaft
Inspection and Repair Dl-39
Crankshaft
Main Bearing Cleaning
and
Inspection Dl-41

Crankshaft
Main Bearings. Dl-40

Crankshaft
Pulley Inspection. Dl-70
Crankshaft
Vibration Damper Inspection. D1-69

Cylinder
Block .Dl-34
Cylinder
Block Cleaning Dl-35
Cylinder
Block Inspection Dl-36

Cylinder
Block Repair. .Dl-37
Cylinder
Head and Valve Repair .Dl-63

Cylinder
Head and Valve Cleaning
and
Inspection.. . .Dl-62

Flywheel
Cleaning and Inspection Dl-52

Flywheel
Housing Cleaning
and
Inspection Dl-54

Hydraulic
Valve
Lifter
Leakdown Test. .Dl-57
Main
Bearing Fitting or

Shim
Stock Dl-42, Dl-43

Oil
Pan Cleaning and Inspection .Dl-51
PAR.
and
Inspection. .... .Dl-68

Oil
Pump Intake and Screen Cleaning. . .Dl-50
Piston and Rod Assembly.
...........
.Dl-48
Piston and Rod Cleaning and Inspection.D1-45
Piston and Rod Disassembly Dl-44
Piston Fitting Dl-46
Piston Ring Fitting. .Dl-47

Ring
Gear
Replacement. .Dl-53
Rocker
Arm Assembly. Dl-60
Rocker
Arm Cleaning and Inspection. . .Dl-59

Rocker
Arm Cover Cleaning

and
Inspection D1-65

Rocker
Arm Disassembly .Dl-58
Timing
Chain
and Sprocket Inspection. . .Dl-66

Timing
Chain
Cover Cleaning

and
Inspection.. . Dl-67

Valve
Installation D1-64
Valve
Lifter
and Push Rod

Cleaning
and Inspection. . Dl-56

Valve
Removal Dl-61

ENGINE REASSEMBLY
Dl-71
Alternator
and Fan Belt Dl-96

Camshaft
Dl-80
Clutch
and Flywheel Housing Dl-79
Cooling Fan.. . .Dl-95
Crankshaft
End Play Check. . Dl-74

Crankshaft
Front Oil Seal Dl-85
Crankshaft
Pulley Dl-89
Crankshaft
Vibration Damper Dl-88
Cylinder
Block and Crankshaft
Rear
Oil Seals Dl-72

Cylinder
Head Assembly .Dl-82

Distributor
Dl-99

Exhaust
Manifold Dl-98
Flywheel
.Dl-78
Fuel
Pump.. .. . Dl-97
Intake
Manifold and Carburetor Assembly Dl-101

Main
Bearing and
Crankshaft
Installation
.
Dl-73

Oil
Filter
Dl-93
Oil
Level
Dipstick Dl-90

Oil
Pan Dl-77
Oil
Pressure Sending Unit Dl-91

Oil
Pump.. .Dl-87
Oil
Pump Intake and Screen Assembly. .Dl-76
Piston and Rod Installation Dl-75

Rocker
Arm Cover. Dl-83

Spark
Plugs.. Dl-100
Starter
Motor Dl-92
Timing
Chain
and Sprocket.
..........
.Dl-84

Timing
Chain
Cover Dl-86
Valve
Lifter
and Push Rod Dl-81

Water
Pump. Dl-94

ENGINE INSTALLATION
Dl-102

FINAL
IN-VEHICLE
ADJUSTMENTS.
D1-103

SERVICE
DIAGNOSIS
Dl-104
ENGINE SPECIFICATIONS
. .Dl-105 75

01
DAUNTLESS
V-6
ENGINE
14358

FIG.
Dl-2—DAUNTLESS
V-6
ENGINE, FRONT SECTIONAL VIEW

1—
Exhaust
Valve
2—
Exhaust
Valve Spring
3—
Rocker
Arm Cover
4—
—Exhaust
Valve Spring Retainer 5—
Exhaust
Rocker Arm
6—
Rocker
Arm Shaft 7— push Rod
8— Tappet
9— Tappet Cover 10—
Cylinder
Head
11—
Rocker
Arm Shaft
12—
Intake
Rocker Arm
13—
Intake
Valve Spring Retainer
14—
Intake
Valve Spring
15—
Intake
Valve 16—
Spark
Plug
17—
Water
Passages 18—
Exhaust
Manifold 19— Piston
20—
Camshaft
21—
Crankshaft

22—
Main
Bearing Cap
23—
Oil
Pan
24—
Crankcase

25— Connecting Rod

The
engine
is pressure lubricated. The oil pump
is located on the timing chain cover and discharges
oil
through an oil filter
into
main oil galleries in
the crankcase to deliver oil to all crankshaft and
camshaft bearings. Piston pins are lubricated by- splash. The timing chain is lubricated by splash
of an oil stream from which oil is directed to the
distributor drive gear from the fuel pump eccentric
on the camshaft. Rocker arms are lubricated from
the oil galleries in the cylinder block through pas- 78

Dl

DAUNTLESS
V-6
ENGINE
In
addition to the instructions covering operations
for disassembling the
engine
out of the vehicle, special instructions are given to cover different
operations required when disassembly is
done
with
the
engine
installed.

During
disassembly operations, the
engine
should be mounted in a suitable
engine
repair stand.

Where
practicable, modify or adapt an existing re­

pair
stand as necessary to accommodate the
engine.
If
an
engine
repair stand is not used, take care to

perform
disassembly operations in a manner that
will
protect personnel against an accident and the
engine
and its parts against damage.

Dl-6.
Mounting Engine
On
Engine Stand

Refer
to Fig. Dl-4.
a.
With
the
engine
supported by a hoist, remove
the clutch housing and clutch. Match
mark
the flywheel and the clutch cover before disassembly to assure proper reassembly.
b. Position the
engine
on the
engine
stand.
c. Release
some
tension of the hoist cables and secure
engine
to stand.

d.
Make sure the position lock on the
engine
stand
is tight to prevent the
engine
from accidentally
inverting.

e.
Release the hoist cables.
FIG.
D1
-4—ENGINE
MOUNTED
ON
STAND

1—
Spacer
J-8690-6
A—Bolt,
i/2-NC
x 3i/2"

2—
Bolt,
3/a-NC
x 4*/2" 5—Adapter 21316-J 3—
Engine
Mounting Stand
Dl-7.
Remove Intake Manifold
and

Carburetor Assembly

Disconnect crankcase vent
hose,
distributor vacuum

hose,
and fuel line from carburetor. Disconnect two distributor leads from ignition coil. Disconnect

wiring
harness from coolant temperature sending

unit.
Remove ten cap
bolts
which attach intake
manifold to cylinder heads. Remove intake mani­
fold assembly and gaskets from
engine.

Dl-8. Remove Exhaust Manifold
The
engine
has two exhaust manifolds. Remove five attaching screws, one nut, and exhaust mani­
fold from each cylinder head.

Dl-9.
Remove Distributor

Disconnect vacuum
hose
and wiring harness from

distributor.
Disconnect spark plug cables from
spark
plugs. Remove sparks plugs from
engine.
Pull

spark
plug cable retainers from brackets on rocker

arm
covers. Remove mounting screw, retainer

bracket,
and distributor from timing chain cover.
If
timing chain and sprockets are not to be re­
moved from
engine,
note
position of distributor
rotor so that it can be installed in identical position.

Dl-10. Remove
Fuel Pump
Disconnect output fuel line from fuel pump. Re­
move
two mounting bolts, fuel pump, and gasket

from
timing chain cover.

Dl-11.
Remove Alternator
and Fan
Belt

Disconnect wiring harness from alternator. Remove nut and flat washer which fasten alternator to
adjustment bracket. Pivot alternator
inward,
to­

ward
engine
cylinder block, to relieve fan belt
tension. Remove fan belt from pulleys. Remove
two attaching screws, mounting bracket, and alter­ nator from right cylinder head of
engine.

Dl-12.
Remove Cooling
Fan and
Water Pump

Refer
to Fig. Dl-5.
Remove four cap screws, lock washers, cooling fan,

fan
hub, and fan drive pulley from flange of water
pump shaft. Remove nine attaching screws, water
pump, alternator adjustment bracket, and water pump from timing chain cover.

Dl-13.
Remove
Oil
Filter

Unscrew
oil filter from
engine
oil pump.

Dl-14.
Remove Starter Motor

Disconnect wiring harness from starter motor and
solenoid. Remove two attaching screws, starter motor, solenoid, and motor attaching bracket from

engine
flywheel housing and cylinder block.

Dl-15.
Remove
Oil
Pressure Sending Unit

Disconnect wiring harness from oil pressure send­
ing unit. Remove oil pressure sending unit from

engine
cylinder block.

Dl-16.
Remove
Oil
Dipstick

Withdraw
and remove oil level dipstick and dip­

stick
tube
from
engine
cylinder block.

Dl-17.
Remove Crankshaft Pulley

Remove six attaching screws and crankshaft pulley

from
crankshaft vibration damper. 80

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

Dl

13296

FIG.
Dl-5—ENGINE
LUBRICATION
AND
COOLING
PARTS

1— Bolt and
Lock
Washer
2—
Fan
Assembly
3—
Fan
and Alternator Belt
4—
Fan
Driven Pulley 5— Water Pump Assembly
6—
Hose
Clamp 7— Thermostat Bypass
Hose

8—Hex
Head Bolt
9— Water Outlet Elbow
10— Water Outlet Elbow Gasket
11— Thermostat
12— Water Pump Gasket
13— Impeller and Insert, Water Pump
14— Water Pump Seal 15— Dowel Pin % x Vfc"
16— Water Pump Cover
17— Bolt,
1/4-20
x 1"
18— Water Pump Shaft and Bearing
19—
Fan
Hub
20—
-Oil
Suction Pipe Gasket
21—
Oil
Suction Housing, Pipe and Flange
22— Bolt,
y4-20
x s/8"
23—
Oil
Pump Screen
24—
Oil
Dipstick
25—
Oil
Pan Gasket
26—
Oil
Pan Assembly
27—
Drain
Plug Gasket
28—
Drain
Plug 29— Screw and
Lock
Washer #6-18 x %
30—
Oil
Pump Shaft and Gear
31—
Oil
Pump Cover Gasket
32— Valve Bypass and Cover Assembly
33—
Oil
Pressure Valve 34— Valve Bypass Spring
35—
Oil
Pressure Valve Cap Gasket
36—
Oil
Pressure Valve Cap
37— Screw V4-20 x lVg"
38— Screw 1/4-20 x 1W' 39—
Fan
Driving Pulley
40— Hex. Head Bolt, x 1"
Dl-13.
Remove
Crankshaft
Vibration Damper

Refer
to Fig. Dl-6.
Remove cap screw and flat washer which attach

crankshaft
vibration damper to crankshaft. Tap

vibration
damper with a soft-headed hammer to remove it from crankshaft.

Dl-19.
Remove Oil Pump
Remove five screws, oil pump cover, and gasket

from
right side of timing chain cover. Remove
two oil pump gears.

D1-20.
Remove Timing Chain Cover

Refer
to Fig. Dl-6. Remove two
bolts
which attach oil pan to timing

chain
cover. Remove five mounting bolts, timing

chain
cover, and gasket from cylinder block of
engine.

Note:
Water pump must be removed from timing

chain
cover before timing chain cover is removed

from
cylinder block.
Dl-21.
Remove Crankshaft Front
Oil
Seal

Refer
to Fig. Dl-6.
Use timing cover aligner and oil seal remover
tool
J-22248 to remove oil seal.

Dl-22.
Remove Timing Chain
and
Spocket

a.
Temporarily install vibration damper (Fig.

Dl-6)
bolt and washer in end of crankshaft.
Turn

crankshaft
so sprockets are positioned with index

marks
aligned as shown in Fig. Dl-7.
This
will

make it easier to install parts. Remove vibration
damper bolt and washer; rap the wrench handle
sharply
to start the bolt without changing position
of sprockets.

Note:
It is not necessary to remove timing chain
dampers unless they are worn or damaged and

require
replacement.
b. Remove front crankshaft oil slinger.
c. Remove bolt and special washer which retain
camshaft distributor drive gear and fuel pump
eccentric at forward end of camshaft. Remove gear
and
eccentric from camshaft. 81