1953 JEEP DJ oil

CLUTCH

is deeply scored or grooved, the part should be

replaced.

b. Inspect driven plate for wear or damage to fac­
ings,
loose
rivets, broken or
loose
torsion springs,

and
flattened cushion springs. If facings are worn
near
rivets or are oily, replace the plate assembly.

A
slight amount of oil on clutch facings
will
cause

clutch
grab and chatter; excessive oil on facings

will
cause slippage. It is not practical to remove
oil
with solvents or by buffing since oil
will
con­
tinue to bleed from facing material when hot. If
oil
is found on driven plate facings, examine trans­
mission drainback hole, pilot bushing,
engine
rear

main
bearing and other points of possible oil leakage. Test the fit of driven plate hub on trans­
mission main drive gear for an easy sliding fit.
c. Inspect clutch release bearing for scoring or ex­ cessive wear on front contact face. Test for rough­

ness
of balls and races by pressing and turning
front race slowly. Inspect main drive gear pilot
bushing in crankshaft. Replace bushing if it is rough or worn. Regardless of whether the old plate

or
a new plate is to be installed, check the plate
for runout. Slide the driven plate, front side first,
over the transmission main drive gear shaft so that

it
is tight on the spline. Index a
dial
indicator to the plate facing as shown in
Fig.
1-9. While holding

firmly
against front end of main drive gear, to take up play in main drive gear bearing, slowly
rotate driven plate and observe the amount of
run­

out shown by indicator. If runout of front facing
exceeds
.025" [0,635 mm.], replace the plate. It
is not practical to correct excessive runout by bending. 12769

FIG.
1-9—RUNOUT
CHECK
—
CLUTCH
PLATE
1—
Front
Facing
(Flywheel
Side)

2—
Dial
Indicator
Set
d.
Check
clutch pilot bushing for excessive wear

or
damage. Replace pilot bushing, if necessary, with

special
removal and installation
tools.
(See
Figs.

1-6 and 1-7). 1-13.
SERVICING
CLUTCH
PRESSURE
PLATE
AND

DISC
—
BORG
&
BECK
V6
(Late
Models)

The
Borg & Beck clutch is a single plate, dry disk
type. It provides smooth
engagement
of
engine
power to the wheels. The clutch consists of a pres­

sure
plate assembly with pressure springs and
release levers, and driven plate assembly. The
driven
plate assembly
uses
spring center vibration
neutralizes and two flexible facings.

The
clutch driven plate is spring cushioned with a facing riveted to both sides. The coil springs around
the hub absorb the power shocks and cushion the

driving
mechanism. The clutch throw-out bearing is of the
ball
type, packed at time of manufacture,

and
requires no further lubrication.
No adjustment for wear is provided in the clutch itself. An individual adjustment is built into the
clutch
cover to adjust the height of the release
levers.
This
adjusting nut is locked in position

and
should never be disturbed unless the clutch assembly has been disassembled for the replace­
ment of worn parts or to correct the height of the release levers.

When
the clutch pedal is depressed (disengaged),
the release bearing is moved toward the flywheel
and
contacts the inner ends of the release levers.

Each
lever is pivoted on a floating pin which re­
mains stationary in the lever and rolls across a short flat portion of the enlarged
hole
in the eye-
bolt. The outer ends of the
eyebolts
extend
through
holes
in the stamped cover and are fitted

with
adjusting nuts to secure the levers in the
correct
position. The outer ends of the release levers

engage
the pressure plate lugs by means of ful-
crums,
which provide knife-edge contact
between

the outer ends of the levers and the lugs as shown
in
Fig.
I-10. 12190

FIG.
MO—CLUTCH
LEVER
POSITIONS
A—Clutch
Engaged
B—Clutch
Disengaged 1-14.
Clutch
Pressure Plate Adjustment

The
clutch pressure plate adjustment must be
checked before installing a new or reconditioned

clutch.
The proper spacer thickness and
gage
length for a particular clutch is listed in Par. 1-30.
Use
Clutch
Adjusting
Fixture
W-296. If the W-296
fixture is not available one can be fabricated as
described in Par. 1-26. 230

CLUTCH

FIG.
1-14—LIFTING
LEVER
AND
EYEBOLT FROM PRESSURE PLATE
1—
Lever

2—
Eyebolt

3—
Fulcrum
A Pressure Plate
lever and the upper end of the
eyebolt
are as
near
together
as possible. Keep the
eyebolt
pin seated in its socket in the lever as shown in Fig.
1-13.
Lift
the fulcrum over the ridge on the end of the lever.
Lift
the lever and
eyebolt
off the
pressure plate as shown in Fig. 1-14.
1-19.
Inspect
Pressure Plate and Disc
Inspect the pressure plate to make sure that it is not cracked or scored.
Check
on a surface plate
for a warped condition, as a pressure plate out of alignment
will
result in clutch chatter.
Machin­

ing or grinding the face of a warped pressure
plate is not recommended. If a warped condition
exists, replace the pressure plate. A new plate
should be installed if the plate or cushion springs appear to be defective. The cushion springs must
not be bent out of shape or flattened.

The
clutch discs for the nine or twelve spring clutches are designed for operation with their
respective clutches. Difference in general appear­ ance of the discs may be noted in the method of
housing the six torque dampening springs and in the
hub design.

After
removal of the clutch assembly, the disc should be inspected. The presence of grease or oil
on the friction facing can cause the clutch to chatter

and
grab during
engagement
and slip at higher speeds. If this condition is evident, the facings or
disc should be replaced and the cause of oil ac­
cumulation corrected. Excessively worn facings
should be replaced. The clutch disc must be in­ stalled with the long end of the hub toward the

transmission.
1-20.
Inspect Transmission Clutch
Shaft

Slide
the clutch driven plate
onto
the transmission

clutch
shaft to make sure that it is free on the
splines. If the splines on the transmission clutch
shaft are
burred,
remove the
burrs
with a fine file or
stone.
If the movement of the clutch driven
plate is not free on the splines, the result
will
be
clutch
drag and
hard
shifting of transmission gears.
1-21.
CLUTCH
PRESSURE
PLATE ASSEMBLY AND
ADJUSTMENT

1-22. Assemble
Clutch
Levers

Prior
to assembly, apply a small amount of petro­

latum
to each slide of the pressure plate lug.

a.
Lay the pressure plate on the block in the
press.
b. Assemble a lever,
eyebolt,
and pin holding the
lever and
eyebolt
as
close
together
as possible.

With
the other hand, grasp the fulcrum as shown
in
Fig. 1-15.

c.
Insert the fulcrum in the
slots
of the pressure
plate lug.
Lower
slightly and tilt the lower
edge

until
it touches the vertical milled surface of the
lug.
Insert the lower end of the
eyebolt
in the

hole
in the pressure plate. The short end of the lever
will
then be under the hook of the lug and

near
the fulcrum.

d.
Slide the fulcrum upward in the
slots
of the

lug.
Lift
it over the ridge on the short end of the
lever and drop it into the
groove
in the lever
(Fig.
1-15).
1-23.
Assemble
Clutch
Spring and
Cover

a.
After all levers are installed, place the felt grease pads over the eyebolts.
Lubricate
pads

sparingly
with light
engine
oil.
Then
place the
clutch
pressure springs in a vertical position on
the spring
bosses.
FIG.
1-15—INSTALLING
CLUTCH LEVERS

1—
Lover

2—
Eyebolt

3—
Fulcrum

4—
Pressure
Plate
232

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

I thickness: .285"
[0,724
cm.], .305"
[0,775
cm.].

Each
spacer should be hardened and ground to size, and then have the dimensional thickness
stamped thereon.

c.
From
flat bar stock at least Vfe" [3 mm.] thick,
make a
gauge
as shown in Fig. 1-22. Harden, grind
to size, and stamp sizes on the
gauge.

1-27.
Clutch Installation

a.
Very
sparingly, apply wheel bearing lubricant
to inner surface of pilot bushing in crankshaft.

Caution:
If
excessive
lubricant is applied to pilot bushing, it
will
run out on face of flywheel when
hot and
ruin
the driven plate facings.
b. Make sure that splines in the driven plate hub
are
clean; apply a light coat of lubricant to splines
of hub and transmission drive gear shaft. Slide plate over gear shaft several times; remove plate
from shaft and wipe off
excess
lubricant.

Caution:
Driven plate facings must be kept clean

and
dry.

c.
Fill
groove
in throwout bearing collar with wheel bearing lubricant. See Fig. 1-23. Make sure
that front bearing retainer of transmission is clean;
apply a light coat of wheel bearing lubricant. Slide
throwout bearing over bearing retainer several times. Remove bearing from retainer and wipe off

excess
lubricant.

12736
FIG.
1-23—LUBRICATION
POINTS
—

CLUTCH
THROWOUT
BEARING
COLLAR

1—Coat
This
Groove 2—Pack
This
Recess
d.
Clean
and apply wheel bearing lubricant to ball
stud in flywheel housing and to the
seat
in clutch

fork.

e.
If disassembled, install pressure plate in the cover assembly, lining up the
groove
on its
edge

with the
groove
on the
edge
of the cover.
Install

pressure plate retracting springs, and the three
drive
strap-to-pressure plate
bolts
and lock washers.

Torque
bolts
11 lb-ft. [1,51 kg-m.].

Note:
The diaphragm
type
clutch assembly is fac­
tory calibrated and requires no adjustment
before
installation. Refer to Par. 1-14 to adjust Borg and

Beck
coil spring
type
clutch assembly.
f.
Install
the pressure plate and driven plate on
flywheel. Support both assemblies with a spare
main
drive gear.

Note:
Be certain that
mark
on clutch cover is
aligned with the
mark
made on the flywheel during
clutch removal.
g.
Install
clutch attaching
bolts
and tighten alter­ nately so that clutch is drawn squarely
into
position
on flywheel.
Each
bolt
must be
tightened
one turn at a time to avoid bending the clutch cover flange.

Torque
bolts
30 to 40 lb-ft. [4,1 a 5,5 kg-m.].

h.
Lubricate
the ball stud and clutch fork with
wheel bearing lubricant and install clutch fork.

Note:
Be certain that fork retaining spring is
tight

on pivot ball stud.

i.
Install
flywheel housing on
engine
cylinder
block.

Caution:
Be certain that dowel pins are installed

in
cylinder block.

j.
Lubricate
the recess on the inside of the throw-
out bearing collar. Be careful not to use too much
lubricant.
See Fig. 1-23.

Caution:
Make certain that the lips of the spring
retainer (attached to the clutch fork) are in
groove
of the bearing. See Fig. 1-24.
k.
Install
throwout bearing assembly and connect
clutch linkage.
I.
Install
transmission as described in Section J. m. Adjust clutch for %"
[19,05
mm.] free travel,
see
Par.
1-3. 235

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

I
1-28.
SERVICE
DIAGNOSIS

SYMPTOMS
PROBABLE
REMEDY

Slipping:
Improper Pedal Adjustment Adjust Pedal Free
Travel

Weak Pressure Springs Replace
Lining
Oil Soaked Install New Driven Plate
Worn
Linings or
Torn
Loose from Plate Install New Driven Plate
Burned Clutch Replace

Grabbing
or
Chattering:
Gummy or Worn Linings Install New Driven Plate
Loose Engine
Mountings
Tighten Scored or Broken Pressure Plate Install New Pressure Plate
Improper Clutch Finger Adjustment............ Readjust

Clutch
Plate Crimp or Cushion Flattened Out.... Replace Driven Plate
Dragging: Too Much Pedal Play. Adjust Improper Finger Adjustment. Readjust
Pressure Plate Binds in Bracket Adjust
Warped Pressure or Driven Plate Replace
Torn
or Loose Clutch Facing. Replace

Rattling:
Broken or Weak Return Springs in Driven Plate.. Replace

Worn
Throwout Bearing Replace
Fingers Improperly Adjusted Readjust

Worn
Driven Plate Hub of Transmission Main Gear Shaft.............. Replace
Pilot Bushings in Flywheel Worn.
.............
Replace
Pilot Bushing in Crankshaft Worn Replace
1-29.
CLUTCH
SPECIFICATIONS

ENGINE
HURRICANE
F4
DAUNTLESS
V-6

DAUNTLESS
V-6

EARLY
MODELS
LATE
MODELS

Pressure Plate;
Auburn
G.M.

Borg and Beck
Type
Single
Dry Plate
Single
Plate, Dry Disc.

Single
Plate, Dry Disc.
No. of Springs 3 Diaphragm Type

Coil
Spring Type (9)

Total
Plate Pressure 1150 lb.
[521,6
kg.]
1600 lb. [725 kg.] 1765 lb. [800 kg.]
Driven Plate Make
Auburn
or Borg & Beck
G.M.

Borg and Beck
Facings Woven
Asbestos
Woven
Asbestos

Woven
Asbestos

Diameter 9.25" [23,4 cm.] 10.4" [26,4 cm.]
10.4" [26,4 cm.]
Thickness .125" [3,17 mm.] .135" [3,38 mm.]
.135" [3,38 mm.]
Torque Capacity 216 lb-ft.
[29,87
kg-m.]
246 lb-ft.
[34.01
kg-m.]

250 lb-ft.
[34,57
kg-m]

Clutch
Release Bearing: Sealed
Ball
Bearing

.
Type Sealed
Ball
Bearing Sealed
Ball
Bearing Sealed
Ball
Bearing

.
Type
Prelubricated Prelubricated
Prelubricated

Clutch
Pilot Bushing:
In
Crankshaft

In
Flywheel
In
Crankshaft
In
Crankshaft

Material
Bronze Bronze
Bronze
Size.
I.D.
.628" [15,9 mm.]
I.D.
.592"
[18,05
mm.]

I.D.
.592"
[18,05
mm.]

Clutch
Pedal Adjustment. .. W
[19,05
mm.]
%n
[19,05
mm.]

%n
[19,05
mm.]
1-30.
CLUTCH
ADJUSTING
FIXTURE
DATA

Manufacturer Disc Diameter Spacer Thickness Gauge Length

Auburn
9j£"
[23,4 cm.]
10.4" [26,4 cm.] .285"
.305"

0,723
cm.]

0,774
cm.]
mtf
[4,9 cm.]
2.0" [5,08 cm.]

9j£"
[23,4 cm.]
10.4" [26,4 cm.] .285"
.305"

0,723
cm.]

0,774
cm.]
mtf
[4,9 cm.]
2.0" [5,08 cm.]

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

J

10489

FIG.
J-2—THREE-SPEED
TRANSMISSION
— T90 1—
Main
Drive
Gear

2—
Main
Drive
Gear
Bearing
Retainer

3—
Main
Drive
Gear
Bearing
Retainer Oil
Seal
4—
Main
Drive
Gear
Snap
Ring

5—
Main
Drive
Gear
Bearing
Snap
Ring

6—
Main
Drive
Gear
Bearing
7—
Synchronizer
Shifting Plate
8—
Shift
Rail
Cap
9—
Shift
Rail—High
and Intermediate
10—
Shift
Rail
Poppet
Ball

11—
Shift
Rail
Poppet
Spring

12—
Shift
Fork—High
and Intermediate

13—
Control
Housing
14—
Control
Lever
Support
Spring

15—
Control
Lever
Housing Pin
16—
Control
Lever
Fulcrum
Ball

17—
Gear
Shift
Lever
18—
Shift
Fork—Low
and Reverse

19—
Sliding
Gear—Low
and Reverse
20—
Main
Shaft
Bearing
Adapter

21—
Main
Shaft
Bearing
22—
Main
Shaft
Washer

23—
Main
Shaft Nut
24—
Main
Shaft

25—
Idler
and Countershaft
Lock
Plate
26—
^Countershaft
Gear
Bearing
Rollers

2
7—Countershaft

28—
Countershaft
Thrust
Washer
Rear—Steel

29—
Countershaft
Thrust
Washer
Rear—Bronze

30—
Countershaft
Gears
31—
Transmission
Case

32—
Main
Shaft Second Speed
Gear
33—
Countershaft
Bearing
Spacer
34—
Synchronizer
Blocking
Ring

35—
Countershaft
Thrust
Washer
Front—Bronze

36—
Countershaft
Bearing
Washer

37—
Intermediate
and High Speed
Clutch
Sleeve

38—
Intermediate
and High
Clutch
Hub

39—
Synchronizer
Spring

40—
Intermediate
and High
Clutch
Hub
Snap
Ring

41—
Main
Shaft Pilot
Bearing
Roller

CJ-5A,
CJ-6A
models, remove the remote control

rods.

d.
Remove the set screw from the transfer case
shift lever pivot pin. Remove the pivot pin, shift

levers,
and shift lever springs. On models
CJ-5A,
and
CJ-6A
remove pivot pin cotter key and the

adjusting
rod attaching nut to remove shift lever.
See
Fig.
J-l.

e. If the vehicle is equipped with power take-off,
remove the shift lever plate screws and lift out the

lever.

f. Disconnect the front and
rear
propeller shafts
from
the transfer case, following the procedure de­

tailed
in Section
L.
Should the vehicle be equipped

with
power take-off, disconnect the transfer case end of the power take-off drive shaft.
g. Disconnect the
speedometer
cable at the transfer case.

h.
Disconnect the hand brake cable.
i.
Disconnect the clutch release cable at beilcrank
yoke end.
j.
Place
jacks
under the transmission and engine,
protecting the
engine
oil pan with a block of wood,
k.
Remove the nuts holding
rear
mounting to

frame
cross member.

I.
Remove the transfer case snubbing rubber bolt
nut at cross member.

m.
Remove
bolts
holding frame center cross mem­

ber
to frame side
rail
and remove cross member,
n.
Remove
bolts
holding transmission to flywheel
bellhousing.
o.
Force
transmission to right to
disengage
clutch
control
lever tube
ball
joint.

p.
Lower
jacks
under
engine
and transmission.

Slide
transmission and transfer case assemblies

toward
rear
of vehicle until the clutch shaft clears the flywheel housing.
q.
Lower
jack
under transmission. Remove trans­ mission and transfer case as an assembly from

under
the vehicle.

r.
For separation of the transmission and transfer
case, refer to Par. J-7. 241

THREE-SPEED
TRANSMISSION

FIG.
J-3—THREE-SPEED
TRANSMISSION
—
T86AA
1—
Main
Drive
Gear

2—
Main
Drive
Gear
Bearing Retainer
3—
Main
Drive
Gear
Bearing Retainer
Oil
Seal

4—
Main
Drive
Gear
Snap Ring
5—
Main
Drive
Gear
Bearing Snap Ring
6—
Main
Drive
Gear
Bearing 7— Synchronizer Shifting Plate
8— Shift
Rail
Cap
9— Shift
Rail
— High and Intermediate
10— Shift
Rail
Poppet
Ball

11— Shift
Rail
Poppet
Spring
12— Shift
Fork
— High and Intermediate
13—
Control
Housing 14—
Control
Lever Support Spring
15—
Control
Lever Housing Pin 16—
Control
Lever
Fulcrum
Ball

17—
Gear
Shift Lever
18— Shift
Fork
— Low and Reverse
19— Sliding
Gear
— Low and Reverse
20—
Main
Shaft Bearing Adapter 21—
Main
Shaft Bearing
22—
Rear
Bearing Snap Ring
23—
Transfer
Case Driving
Gear

24—
Main
Shaft Washer
25—Main Shaft Nut
26—
Main
Shaft
27—
Idler
and Countershaft Lockplate
28— Countershaft
Gear
Bearing Rollers
29— Countershaft
30— Countershaft Thrust Washer
Rear
— Steel 31— Countershaft Thrust Washer

Rear
— Bronze
32— Countershaft Gears
33—
Transmission
Case
34—
Main
Shaft Second Speed
Gear

35— Countershaft Bearing Spacer
36— Synchronizer Blocking Ring 37— Countershaft Thrust Washer

Front
— Bronze
38— Countershaft Bearing Washer
39— Intermediate and High Clutch
Sleeve
40— Intermediate and High Clutch Hub

41
—Synchronizer Spring
42— Intermediate and High Clutch Hub
43—
Main
Shaft Pilot Bearing Roller J-7.
Separating Transmission
and

Transfer Case

a.
Remove the six screws and lockwashers attach­
ing the transfer case rear cover and remove the cover. Or, should the vehicle be equipped with a
power
take-off,
remove the power take-off shift
unit which replaces the cover.
b. Remove
cotter
pin, nut, and washer which
hold the transfer case main drive gear on the rear
end of the transmission mainshaft. If
possible
at
this point, remove the main drive gear. If not possible, see
steps
d and e
below.

c. Remove the transmission-to-transfer-case screws.

d.
Separate the transfer case from the transmission.
When separating the two units, use care that the
transmission mainshaft bearing, which bears in
both
housings, remains in the transmission housing.

To
separate the two units if the transfer case main
drive gear was not removed in
step
b
above,
follow

the procedure in
step
e
below.

e.
Install transmission mainshaft retaining plate,

tool
W-194, as shown in Fig. J-6 to prevent the mainshaft from pulling out of the transmission
case. Should this
tool
be unavailable,
loop
a
piece
of wire around the mainshaft directly back of the mainshaft
second-speed
gear. Install the transmis­
sion shift housing right and
left
front attaching
screws part way
into
the transmission case. Twist
the wire and attach each end to one of the screws.
Draw
the wire tightly. With the mainshaft securely

in
place, support the transfer case and, with a rawhide mallet or brass drift and hammer, tap 242

1— Retainer Screw
2— Retainer Screw Gasket
3—
Main
Drive Gear Bearing Retainer
4—
Oil
Seal 5— Bearing Snap Ring
6—
Main
Drive Gear Snap Ring 7—
Main
Drive Gear Bearing
8—
Main
Drive Gear
9— Mainshaft Pilot Bearing Rollers
10— Retainer Gasket
11—
Case
Cover Gasket 12—Transmission Case Cover
13—
Cover
Screw
14— Transmission Case 15— Synchronizer Blocking Ring
16— Synchronizer Spring
17— Synchronizer Shifting Plate
18— Intermediate and High Clutch Hub
19—
Intermediate
and High Clutch
Sleeve

20— Intermediate and High Shift
Fork
21—
Second
Speed
Gear
22— Mainshaft
23—
Low
and Reverse Sliding Gear 24—
Low
and Reverse Shifting
Shoe
25— Mainshaft Bearing Spacer
26— Mainshaft Bearing Adapter
27— Mainshaft Bearing
28— Mainshaft Washer
29— Mainshaft Nut
30—
Lock
Plate
31— Countershaft
32—
Steel
Thrust Washer
33— Bronze Thrust Washer
34— Countershaft Bearing Spacer
35— Countershaft Bearing Center Spacer
36— Countershaft Bearing Rollers
37— Reverse Idler Gear Shaft
38— Reverse Idler Gear Assembly
39— Countershaft Gear 40— Countershaft Front Thrust Washer
41—
Lockwasher

42— Nut
43—
Control
Lever Washer
44—
Low
and Reverse Control Lever
45—
Low
and Reverse Shift Lever
46— Shift Lever Interlock Pin
47— Shift Lever
Poppet
Spring
48— Shift Lever
Poppet
Ball

49— Intermediate and High Control Lever 50— Interlock Shift Lever
Sleeve

51— High and Intermediate Shift Lever
52—
Oil
Seal 53— Plug
54—
Clutch
Hub Snap Ring 55—
Taper
Pin
56—
Front
Oil Retaining Washer

'Jeep*
UNIVERSAL
SERIES'
SERVICE
MANUAL

lightly
on the end of the
mainshaft
to
loosen
the

gear
and
separate
the two
units.

J-8.
Disassembly
—
T90,
T86AA
®
Refer to Fig. J-5, J-7
a. If the transfer
case
is
attached,
separate
it from
the
transmission
as
outlined
in Par. J-7. b.
Remove
the
shift
housing
and
gasket
from the
top of the
transmission
case.
The
shift
housing
can
be
disassembled,
if
necessary,
at
this
point
by re­
moving
the
shift
rails and forks from the
shift

housing.
Use care not to
lose
the
poppet
balls
and
springs.

Note;
On
CJ-5
A
and
C
J-6A
models
equipped
with
side-shift
remote-control
transmission
it is
neces­

sary to
remove
the main drive
gear
before
the
shift

forks can be
removed.

e.
Remove
the
three
screws
and
washers
attaching
the
front
main drive
gear
bearing
retainer to the
transmission.
Remove
the retainer and
gasket,

d.
Remove
the two
socket-head
screws
from the
front
end of the
transmission
case.
These
screws

support
the oil
collector
inside
the
case.

Note:
The oil
collector
has
been
discontinued
in

late
production
transmission
assemblies.
11881

FIG.
J-6—MAIN
SHAFT
RETAINING
PLATE

13321

FIG.
J-7—T86AA
THREE-SPEED
TRANSMISSION
—
CANE
SHIFT

1—
Bearing
Retainer Screws
2—
Main
Drive Gear Bearing Retainer
3—
Bearing
Retainer Oil Seal

,
4—Bearing Snap Ring
5—
Main
Drive Gear Snap Ring 6—
Main
Drive Gear Bearing 7—
Front
Bearing Oil Retaining Washer
8—
Main
Drive Gear
9— Pilot Roller Bearing
10— Shift
Rail
Cap
11—
Poppet
Ball

12—
Poppet
Spring
13—
Lock
Washer
14— Shift Housing Bolt
15—
Control
Housing 16— Interlock Plunger
17— Shift Lever Spring
18— Shift Tower Gasket
19— Blocking Ring 20—
Clutch
Hub Snap Ring
21— Synchronizer Spring
22— Synchronizer Plate
23—
Clutch
Hub
24—
Clutch
Sleeve

25— High and Intermediate Clutch
Fork

26— Shift
Fork
Pin
27— High and Intermediate Shift
Rail

28— Second Speed Gear 29—
Main
Shaft
30—
Low
and Reverse Sliding Gear
31—
Low
and Reverse Shift
Fork

32—
Low
and Reverse Shift
Rail
33—
Bearing
Spacer
34—
—Rear
Bearing Adapter
35—Rear
Bearing 36—
Rear
Bearing Snap Ring
37— Nut
38—Washer 39—
Transfer
Case Drive Gear
40—Lock
Plate
41 —Countershaft
42—
Rear
Countershaft Thrust Washer
(steel)

43—
Rear
Countershaft Thrust Washer (bronze)
44— Countershaft Bearing Washer
45— Countershaft Bearing 46— Countershaft Center Bearing Spacer
47— Reverse Idler Gear Shaft
48— Reverse Idler Gear Bearing Washer
49— Reverse Idler Gear Roller Bearings 50— Reverse Idler Gear
51— Countershaft Gear 52— Countershaft Front Thrust Washer
53— Plug 54— Shift Lever
55—
Transmission
Case
56— Retainer Gasket 245