2024 MAZDA CX90 lock

How to Use the
Automatic Locking Mode
NOTE
Follow the child-restraint system
manufacturer's instructions carefully. If
you are not sure whether you have a
LATCH system or tether, check in the
child-restraint system manufacturer's
instructions and follow them
accordingly. Depending on the type of
child-restraint system, it may use
LATCH system instead of seat belts or if
the belt goes across the child's chest,
may recommend against using
automatic locking mode.
1. (Second-row seat)
Adjust the second-row seat
position using the following
procedure.
1. Fold the second-row seatback
forward.
2. Raise the second-row seatback until a click sound is heard and
it is locked in place.
2.(Second-row seat)
Adjust the angle of the second-row
seatback so that there is no gap
between the child-restraint system
and the second-row seatback.
3. Make sure the seatback is securely latched by pushing it back until it is
fully locked.
4. If a removable head restraint isequipped, remove it. However,
when installing a backless booster
seat, always install the vehicle head
restraint to the seat where the
backless booster seat is installed.
Refer to How to Use the Head
Restraints on page 3-48.
5. Secure the child-restraint system with the lap portion of the lap/
shoulder belt. See the
manufacturer's instructions on the
child-restraint system for belt
routing instructions.
6. To get the retractor into the automatic locking mode, pull the
shoulder belt portion of the seat
belt until the entire length of the
belt is out of the retractor.
Equipment to Protect Occupants/Pedestrians
Child-restraint Systems
3-59
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

7. Push the child-restraint systemfirmly into the vehicle seat. Be sure
the belt retracts as snugly as
possible. A clicking noise from the
retractor will be heard during
retraction if the system is in the
automatic locking mode. If the belt
does not lock the seat down tight,
repeat this step.
NOTE
Inspect this function before each
use of the child-restraint system.
You should not be able to pull the
shoulder belt out of the retractor
while the system is in the automatic
locking mode. When you remove
the child-restraint system, be sure
the belt fully retracts to return the
system to emergency locking mode
before occupants use the seat belts.
8. If your child-restraint system requires the use of a tether strap,
refer to the manufacturer's
instructions to hook and tighten the
tether strap.
If You Must Use the Front
Seat for Children
If you cannot put all children in the
rear seat, at least put the smallest
children in the rear and be sure the
largest child up front uses the shoulder
belt over the shoulder.
NEVER put a rear-facing child-restraint
system on the front passenger seat
whether your vehicle is equipped with
an occupant classification sensor or
not.
This seat is also not set up for tethered
child-restraint systems, put them in
one of the rear seat positions set up
with tether anchors.
Likewise the LATCH child-restraint
system cannot be secured in the front
passenger's seat and should be used in
the second-row seat.
Do not allow anyone to sleep against
the side window since your vehicle has
side and curtain air bags, it could
cause serious injuries to an out of
position occupant. As children more
often sleep in cars, it is better to put
them in the rear seat. If installing the
child-restraint system on the front seat
is unavoidable, follow these
instructions when using a front-facing
child-restraint system in the front
passenger's seat.
NOTE
To check if your front seats have side
air bags:
Mazda vehicles equipped with side
air bag will have a "SRS AIRBAG" tag
on the outboard shoulder of the
front seats.
To check if your vehicle has curtain
air bags:
Equipment to Protect Occupants/Pedestrians
Child-restraint Systems
3-60
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Always remove the head restraint and
install child-restraint system (except
when installing a backless booster
seat).
Installing a child-restraint system
without removing the head restraint is
dangerous. The child-restraint system
cannot be installed correctly which
may result in death or injury to the
child in a collision.
Always install the head restraint and
adjust it to the appropriate position
after removing the child-restraint
system.
Driving with the head restraint
removed is dangerous as impact to the
occupant's head cannot be prevented
during emergency braking or in a
collision, which could result in a
serious accident, injury or death.
Refer to How to Use the Head
Restraints on page 3-48.
Do not allow a child or anyone to
lean over to or against the side
window of a vehicle with side and
curtain air bags.It is dangerous to allow anyone to lean
over to or against the side window, the
area of the front passenger seat, the
front and rear window pillars and the
roof edge along both sides from which
the side and curtain air bags deploy,
even if a child-restraint system is used.
The impact of inflation from a side or
curtain air bag could cause serious
injury or death to an out of position
child. Furthermore, leaning over to or
against the door could block the side
and curtain air bags and eliminate the
advantages of supplemental
protection. Because the front seats are
equipped with front air bags, the rear
seat is always a better location for
children. Take special care not to allow
a child to lean over to or against the
side window, even if the child is seated
in a child-restraint system.
Equipment to Protect Occupants/Pedestrians
Child-restraint Systems
3-62
CX-90_8KG7-EA-22L_Edition1_new2022-11-17 16:05:04

How to Install a
Child-Restraint System
on the Front Passenger's
Seat
1. Make sure the vehicle power isswitched off.
2. Slide the seat as far back as
possible.
3. Remove the head restraint.However, when installing a backless
booster seat, always install the
vehicle head restraint to the seat
where the backless booster seat is
installed.
4. Place the child-restraint system on the seat without putting your
weight on the seat and fasten the
seat belt. See the manufacturer's
instructions on the child-restraint
system for belt routing instructions.
5. To get the retractor into the automatic locking mode, pull the
shoulder belt portion of the seat
belt until the entire length of the
belt is out of the retractor.
6. Push the child-restraint system firmly into the vehicle seat. Be sure
the belt retracts as snugly as
possible. A clicking noise from the
retractor will be heard during
retraction if the system is in
automatic locking mode. If the belt
does not lock the seat down tight,
repeat the previous step and also
this one.
NOTE
Inspect this function before each
use of the child-restraint system.
You should not be able to pull the
shoulder belt out of the retractor
while the system is in the
automatic locking mode. When
you remove the child-restraint
system, be sure the belt fully
retracts to return the system to
emergency locking mode before
occupants use the seat belts.
Follow the child-restraint system
manufacturer's instructions
carefully.
Depending on the type of
child-restraint system, it may not
employ seat belts which are in
automatic locking mode.
7. Seat your child safely in the child-restraint system and secure
the child according to the
instructions from the child-restraint
system manufacturer.
8. Switch the vehicle power ON and make sure the front passenger air
bag deactivation indicator light
illuminates after installing a
child-restraint system on the front
passenger seat.
If the front passenger air bag
deactivation indicator light does
not illuminate, remove the
child-restraint system, switch the
vehicle power to OFF, and then
re-install the child-restraint system
(page 3-16).
Equipment to Protect Occupants/Pedestrians
Child-restraint Systems
3-63
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the LATCHLower Anchor
Installation on second-row/third-row
right seat
1.(Second-row seat)
First, adjust the front seat to allow
clearance between the
child-restraint system and the front
seat.
Refer to How to Use the Front Seats
on page 3-30.
2. (Second-row seat)
Adjust the second-row seat
position using the following
procedure.
1. Fold the second-row seatback
forward.
2. Raise the second-row seatback until a click sound is heard and
it is locked in place.
3.(Second-row seat)
Adjust the angle of the second-row
seatback so that there is no gap
between the child-restraint system
and the second-row seatback.
4. Make sure the seatback is securely latched by pushing it back until it is
fully locked.
5. Remove the cover of the child-restraint system's LATCH
lower anchors to verify the
locations of the LATCH lower
anchors.
Second-row seat
Third-row seat
1. LATCH lower anchor
NOTE
The LATCH lower anchors
marking on the cover indicates
the position of the LATCH lower
anchors for the attachment of a
child-restraint system.
6. Remove the head restraint. However, when installing a backless
booster seat, always install the
vehicle head restraint to the seat
where the backless booster seat is
installed.
Refer to How to Use the Head
Restraints on page 3-48.
7. Secure the child-restraint system using BOTH LATCH lower anchors,
following the child-restraint system
manufacturer's instruction. Pull on
the child-restraint to be sure both
anchors are engaged.
Equipment to Protect Occupants/Pedestrians
Child-restraint Systems
3-66
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

4Opening/closing
Key......................................... 4-4Key....................................... 4-4
Warnings and Cautions for Using
the Key................................. 4-4
How to Use the Key............... 4-5
Convenient Ways to Use the
Key....................................... 4-8
Advanced Keyless Entry
System.....................................4-9 Advanced Keyless Entry
System
*................................. 4-9
Warnings and Cautions for Using
the Advanced Keyless Entry
System.................................. 4-9
How to Use the Advanced Keyless
Entry System........................ 4-10
Doors.................................... 4-11 Warnings and Cautions When
Using the Doors...................4-11
How to Use the Door Lock ..........
.......................................... 4-12
Convenient Ways to Use the
Doors................................. 4-16
Liftgate.................................. 4-17 Warnings and Cautions for Using
the Liftgate.......................... 4-17
How to Use the Liftgate........ 4-18
Po w e r L i ft g a te
*..................... 4-19
Warnings and Cautions for Using
the Power Liftgate................ 4-19
How to Use the Power
Liftgate................................ 4-21
Convenient Ways to Use the
Power Liftgate...................... 4-25
Hood.....................................4-26 Warnings and Cautions for Using
the Hood............................ 4-26
How to Use the Hood.......... 4-27
Windows............................... 4-28 Power Windows...................4-28
Warnings and Cautions for Using
the Power Windows............. 4-28
How to Use the Power
Windows.............................4-29
Convenient Ways to Use the
Power Windows...................4-30
Sunroof................................. 4-31 Pa n o ra m a S u n ro o f
*.............. 4-31
Warnings and Cautions for Using
the Panorama Sunroof.......... 4-31
How to Use the Panorama
Sunroof............................... 4-32
Moonroof
*.......................... 4-34
Warnings and Cautions for Using
the Moonroof...................... 4-35
How to Use the Moonroof...........
.......................................... 4-36
Security System.......................4-37 Security System.................... 4-37
Warnings and Cautions for Using
the Security System.............. 4-37
Immobilizer System..............4-38
*Some models.4-1
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Key
All doors, fuel-filler lid/charging port
lid, and the liftgate can be locked/
unlocked by pressing the key switch.
The key must be carried by the driver.
Key Code Number Plate
An auxiliary key can be ordered based
on the key code number printed on
the key code number plate at an
Authorized Mazda Dealer.
Store the key code number plate in a
safe place (not in the vehicle).
Do not divulge the key number to
others.
Warnings and Cautionsfor Using the Key
WARNING
Do not leave the key in your vehicle
with children and keep them in a
place where your children will not
find or play with them.
Leaving children in a vehicle with the
key is dangerous. This could result in
someone being badly injured or even
killed. Children may find these keys to
be an interesting toy to play with and
could cause the power windows or
other controls to operate, or even
make the vehicle move.
CAUTION
Radio equipment like this is
governed by laws in the United
States.
Changes or modifications not
expressly approved by the party
responsible for compliance could
void the user's authority to operate
the equipment.
 Because the key (transmitter) uses
low-intensity radio waves, it may not
function correctly under the
following conditions:
 The key (transmitter) is carried with
communication devices such as
cellular phones.
 The key (transmitter) contacts or is
covered by a metal object.
 The key (transmitter) is near
electronic devices such as personal
computers.
 Non-Mazda genuine electronic
equipment is installed in the
vehicle.
Opening/closing
Key
4-4
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

There is equipment which
discharges radio waves near the
vehicle.
 The key (transmitter) may consume
battery power excessively if it
receives high-intensity radio waves.
Do not place the key (transmitter)
near electronic devices such as
televisions or personal computers.
 To avoid damage to the key
(transmitter), DO NOT:
 Drop the key (transmitter).
 Get the key (transmitter) wet.
 Disassemble the key (transmitter).
 Expose the key (transmitter) to
high temperatures on places such
as the dashboard, under direct
sunlight.
 Expose the key (transmitter) to any
kind of magnetic
field.
 Place heavy objects on the key
(transmitter).
 Put the key (transmitter) in an
ultrasonic cleaner.
 Put any magnetized objects close
to the key (transmitter).How to Use the Key
When pressing the button, the
operation indicator light turns on.
1. Operation indicator light
2. Lock button (
)
3. Unlock button (
)
4. Power liftgate button (
)*
5. Panic button ()
Lock button
Press the lock button with all of the
following conditions met.
The vehicle power is switched OFF.
The doors, liftgate, fuel-filler lid/
charging port lid are locked, the hazard
warning lights operate 1 time.
A beep sound will be heard once.

To confirm that all the doors, liftgate,
and fuel-filler lid/charging port lid
have been locked, press the lock
button again within 5 seconds. If they
are closed and locked, the horn will
sound.
Opening/closing
Key
*Some models.4-5
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04