2024 MAZDA CX90 transmission

Recreational towing
An example of "recreational towing" is towing your vehicle behind a motorhome.
The transmission is not designed for towing this vehicle on all 4 wheels.
When doing recreational towing refer to "Having the Vehicle Towed" (page 8-5)
and "Using the Towing Hooks" (page 8-6) and carefully follow the instructions.
Other Equipment
Towing (U.S.A. and Canada)
7-67
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the
HomeLink Wireless Control System
Programming the HomeLink System
The HomeLink system provides 3
buttons which can be individually
selected and programmed using the
transmitters for current, on-market
devices as follows:
1. Verify that there is a remote control transmitter available for the device
you would like to program.
NOTE
It is recommended that a new
battery be placed in the hand-held
transmitter of the device being
programmed to HomeLink for
quicker training and accurate
transmission of the radio-frequency
signal.
2. Press and release the HomeLink button you would like to program.
The indicator light flashes slowly in
amber when the button is pressed.
1. Indicator light
2. HomeLink button
3. Hold the hand-held transmitter 3 to 7 cm (1.2 to 2.7 in) away from the
HomeLink button you would like to
program while keeping the
indicator light in view.
NOTE
Depending on the hand-held
transmitter, it may be easier to do
the programming by holding it
about 20 cm (7.9 in) away from the
HomeLink button.
4. Press the hand-held transmitter button continuously until the
indicator light changes from amber
(flashing) to green (on/flashing).
NOTE
Some gate operators and garage
door openers may require you to
replace this Programming Step 4
with procedures noted in the “Gate
Operator/Canadian Programming”
section.
5. Press the HomeLink button again to check if the programming has been
completed.
If the indicator light remains on in
green, the programming is
complete and the device becomes
operational.
If the indicator light flashes rapidly
in green, firmly press and hold the
Homelink button and release it
after two seconds have passed.
Repeat this process up to three
times to complete the
programming. The device becomes
operational and programming is
complete. If the device does not
operate, go to the next step.
6. At the garage door opener receiver (motor-head unit) in the garage,
locate the “learn” or “smart” button.
This can usually be found where the
hanging antenna wire is attached to
the motor-head unit.
7. Firmly press and release the “learn” or “smart” button. (The name and
color of the button may vary by
manufacturer.)
Other Equipment
HomeLink Wireless Control System
7-69
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

NOTE
Complete the programming within
30 seconds.
8. Return to the vehicle and firmly press and hold the Homelink
button, and then release it after two
seconds have passed. Repeat the
“press/hold/release” sequence a
second time, and, depending on
the brand of the garage door
opener (or other rolling code
equipped device), repeat this
sequence a third time to complete
the programming process.
Press the programmed HomeLink
button and make sure that the
HomeLink System operates.
If the status indicator arrows are
flashing , refer to Programming
two-way communication.
1. Indicator light
For questions or comments, please
contact HomeLink at
www.homelink.com or
www.youtube.com/
HomeLinkGentex, or the HomeLink
toll-free hotline at 1-800-355-3515
(for calls placed outside of the USA,
Canada, and Puerto Rico,
international rates will apply and
may differ based on landline or
mobile phone).
Gate operator/Canadian
Programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or
quit) after several seconds of
transmission ― which may not be long
enough for HomeLink to pick up the
signal during programming. Similar to
this Canadian law, some U.S. gate
operators are designed to “time-out”
in the same manner.
If you live in Canada or are having
difficulties programming a gate
operator by using the programming
procedures (regardless of where you
live), replace Step 4 of Programming
the HomeLink System with the
following:
NOTE
If programming a garage door opener
or gate operator, it is advised to unplug
the device during the “cycling” process
to prevent possible overheating.
While the indicator light is flashing in
amber, press the button on the
hand-held transmitter for 2 seconds
and release it repeatedly until the
indicator light changes from amber to
green.
Go back to Step 5 of Programming the
HomeLink System to complete the
procedure.
Operating the HomeLink System
Press the programmed HomeLink
button to operate a programmed
device.
Reprogramming the HomeLink system
To program a device to HomeLink
using a HomeLink button previously
trained, follow these steps:
1. Press and hold the desired
HomeLink button. Do not release
the button.
2. After 20 seconds, the indicator light
flashes in amber. After the indicator
light flashes, release the HomeLink
button.
Other Equipment
HomeLink Wireless Control System
7-70
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Windshield Wipers Operate at High
Speed.................................... 8-34Have the Vehicle Inspected ..........
.......................................... 8-34
Washer Fluid Does Not Spray ...........
............................................ 8-35 Inspecting Washer Fluid
Level................................... 8-35
Active Driving Display Does Not
Operate................................. 8-36 Active Driving Display Does Not
Operate.............................. 8-36
Warning/Indicator Light Turns
On........................................ 8-37 Warning Lights..................... 8-37
Brake System Warning
Light................................... 8-37
Lead-Acid Battery Charging
System Warning Light........... 8-38
Hybrid System Warning
Light................................... 8-39
Remaining High Voltage Battery
Power Warning Light............ 8-39
Charging System Warning
Light................................... 8-40
Output Restriction Warning
Light................................... 8-40
Engine Oil Warning Light...... 8-41
High Engine Coolant Temperature
Warning Light...................... 8-41
Electric Power Steering Warning
Light................................... 8-42
Shift System Warning Light ...........
.......................................... 8-42
ABS Warning Light................8-43
Master Warning Light........... 8-43Brake Control System Warning
Light................................... 8-44
Electric Parking Brake (EPB)
Indicator Light..................... 8-44
Check Engine Warning
Light................................... 8-45
Automatic Transmission Warning
Light................................... 8-45
AWD Warning Light............. 8-46
Tire Pressure Monitoring System
(TPMS) Warning Light
(Flashing)............................ 8-46
TCS/DSC Indicator Light (Turns
on)..................................... 8-47
Air Bag/Seat Belt Pretensioner
System Warning Light........... 8-47
KEY Warning Light (Red)....... 8-48
Security Indicator Light......... 8-48
High Beam Control System (HBC)
Warning Light (Amber)
*........ 8-49
i-ACTIVSENSE Warning
Light................................... 8-49
Exterior Lights Warning
Light................................... 8-50
Low Fuel Warning Light.........8-50
Check Fuel Cap Warning
Light................................... 8-51
Engine Oil Level Warning
Light................................... 8-51
Seat Belt Warning Light (Front
Seat)................................... 8-52
Seat Belt Warning Light (Rear
Seat) (Red).......................... 8-52
Rear Seat Alert Warning Light
*......
.......................................... 8-53
Low Washer Fluid Amount
Warning Light
*..................... 8-53
Door-ajar Warning Light/Liftgate-
open Warning Light/Hood-open
Warning Light...................... 8-54
8-2*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Having the Vehicle Towed
We recommend that towing be done
only by an Authorized Mazda Dealer
or a commercial tow-truck service.

Proper lifting and towing are necessary
to prevent damage to the vehicle.
Particularly when towing an AWD
vehicle, where all the wheels are
connected to the drive train, proper
transporting of the vehicle is absolutely
essential to avoid damaging the drive
system. Government and local laws
must be followed.
WARNING
Always tow an AWD vehicle with all
four wheels off the ground.
Towing an AWD vehicle with either the
front or rear wheels on the ground is
dangerous as the drive train could be
damaged, or the vehicle could trail
away from the tow truck and cause an
accident. If the drive train has been
damaged, transport the vehicle on a
flatbed truck.
CAUTION
Do not tow the vehicle pointed
forkward with driving wheels on the
ground. This may cause internal
damage to the transmission.
Do not tow with sling-type
equipment. This could damage your
vehicle. Use wheel-lift or flatbed
equipment.
If the parking brake cannot be
released when towing the vehicle,
transport the vehicle with all front
and rear wheels raised
off the ground
as shown in the figure. If the vehicle
is towed without raising the wheels off the ground, the brake system
could be damaged.
1. Wheel dollies
What to Do in Case of Emergency
When Towing is Required
8-5
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Check Engine WarningLight
WARNING
Do not disconnect the lead-acid
battery cables when the check engine
warning light is turned on/flashing.
The engine may be damaged when
reconnecting the lead-acid battery
cables, which could result in a fire.
The light turns on if the engine has a
problem while it is running.
Park the vehicle in a safe place
immediately and contact an
Authorized Mazda Dealer.
If any of the following problems occur,
the check engine warning light turns
on.
There is a problem with the hybrid
system
There is a problem with the emission
control system
There is a problem with the
transmission control system
The fuel tank level being very low or
approaching empty.
The fuel-filler cap is missing or not
tightened securely
If the check engine warning light
remains turned-on/flashing, do not
drive at high speed and have the
vehicle inspected by an Authorized
Mazda Dealer as soon as possible.
Automatic Transmission Warning Light
The light turns on if the system has a
problem.
Contact an Authorized Mazda Dealer.
CAUTION
Do not drive the vehicle with the
automatic transmission warning light
turned on. If the vehicle continues to
be driven while the automatic
transmission warning light is turned on,
the transmission could be damaged.
Have your vehicle inspected by an
Authorized Mazda Dealer as soon as
possible.
What to Do in Case of Emergency
Warning/Indicator Light Turns On
8-45
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Ve h i c l e Pro b l e m Wa r n i n gSound
If any of the following problems occur,
a warning sound is activated.
Automatic transmission problemIncrease in automatic transmission
internal temperature
Hybrid system problemBrake system problemElectric Parking Brake (EPB) problemEngine oil pressure decreaseEngine coolant temperature increaseEngine system problemShift control system problemCharging system problemApproaching vehicle audible system
problem
Check the information regarding the
warning indication on the center
display or the instrument cluster.
Shift Position Warning Sound
A warning sound is activated when the
selector lever position and the shift
position of the vehicle do not match.
Check the selector lever position.
What to Do in Case of Emergency
Warning Sound is Activated
8-61
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year―at the beginning of
the winter season ―and before
traveling where temperatures may drop
below freezing.

Inspect the condition and connections
of all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.

There are two cooling circuits: one for
the automatic transmission, and the
other for the engine. Check both
circuits.
The coolant should be at full in the
radiator and between the F and L
marks, and between the FULL and
LOW marks on the coolant reservoir
when the engine is cool.
There are two coolant reservoir tanks.
Check each of them.
1. The tank for the EV system
2. The tank for the engine

If it is at or near the LOW position, add
enough coolant to the coolant
reservoir to provide freezing and
corrosion protection and to bring the
level to FULL.
Securely tighten the coolant reservoir
tank cap after adding coolant.
CAUTION
 Radiator coolant will damage paint.
Rinse it off quickly if spilled.
 If the “FL22” mark is shown on or
near the cooling system cap, use of
FL-22 is recommended when
replacing engine coolant. Using
engine coolant other than FL-22 may
cause serious damage to the engine
and cooling system.

If the coolant reservoir is empty or new
coolant is required frequently, consult
an Authorized Mazda Dealer.
Inspection and Servicing/Cleaning
Engine Compartment Inspection
9-15
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04