
352SERVICING AND MAINTENANCE
(Continued)
CHECKING OIL LEVEL
To ensure proper engine lubrication, the engine oil
must be maintained at the correct level. Check the
oil level at regular intervals, such as every fuel
stop. The best time to check the engine oil level is
about five minutes after a fully warmed up engine
is shut off.
Checking the oil while the vehicle is on level ground
will improve the accuracy of the oil level readings.
There are four possible dipstick types:
Crosshatched zone.
Crosshatched zone marked SAFE.
Crosshatched zone marked with MIN at the low
end of the range and MAX at the high end of the
range.
Crosshatched zone marked with dimples at the
MIN and the MAX ends of the range.
NOTE:Always maintain the oil level within the crosshatch
markings on the dipstick.
Adding 1 qt (1 L) of oil when the reading is at the
low end of the dipstick range will raise the oil level
to the high end of the range marking.
ADDING WASHER FLUID
The fluid reservoir is located under the hood and
the fluid level should be checked at regular
intervals. Fill the reservoir with windshield washer
solvent only (not radiator antifreeze). When
refilling the washer fluid reservoir, take some
washer fluid and apply it to a cloth or towel and
wipe the wiper blades clean. This will help blade
performance.
To prevent freeze-up of your windshield washer
system in cold weather, select a solution or mixture
that meets or exceeds the temperature range of
your climate. This rating information can be found
on most washer fluid containers.After the engine has warmed up, operate the
defroster for a few minutes to reduce the
possibility of smearing or freezing the fluid on the
cold windshield. Windshield washer solution used
with water as directed on the container, aids
cleaning action, reduces the freezing point to avoid
line clogging, and is not harmful to paint or trim.MAINTENANCE-FREE BATTERY
Your vehicle is equipped with a maintenance-free
battery. You will never have to add water, and
periodic maintenance is not required.
NOTE:Replacement batteries should both be of equal
capacity to prevent damage to the vehicle's
charging system.
CAUTION!
Overfilling or underfilling the crankcase will
cause oil aeration or loss of oil pressure. This
could damage your engine.
WARNING!
Commercially available windshield washer
solvents are flammable. They could ignite and
burn you. Care must be exercised when filling or
working around the washer solution.
WARNING!
Battery fluid is a corrosive acid solution and
can burn or even blind you. Do not allow
battery fluid to contact your eyes, skin, or
clothing. Do not lean over a battery when
attaching clamps. If acid splashes in eyes or
on skin, flush the area immediately with large
amounts of water Ú
page 334.
23_DPF_OM_EN_USC_t.book Page 352

SERVICING AND MAINTENANCE353
PRESSURE WASHING
Cleaning the engine compartment with a high
pressure washer is not recommended.
VEHICLE MAINTENANCE
An authorized dealer has the qualified service
personnel, special tools, and equipment to
perform all service operations in an expert
manner. Service Manuals are available which
include detailed service information for your
vehicle. Refer to these Service Manuals before
attempting any procedure yourself.
NOTE:Intentional tampering with emissions control
systems may void your warranty and could result in
civil penalties being assessed against you.
ENGINE OIL
Engine Oil Selection— Gasoline Engine
Use only the manufacturer's recommended fluid
Úpage 419.
NOTE:Hemi engines (6.4L) at times can tick right after
startup and then quiet down after approximately
30 seconds. This is normal and will not harm the
engine. This characteristic can be caused by short
drive cycles. For example, if the vehicle is started
then shut off after driving a short distance. Upon
restarting, you may experience a ticking sound.
Other causes could be if the vehicle is unused for
an extended period of time, incorrect oil, extended
oil changes or extended idling. If the engine
continues to tick or if the Malfunction Indicator
Light (MIL) comes on, see the nearest authorized
dealer.
Battery gas is flammable and explosive. Keep
flame or sparks away from the battery. Do not
use a booster battery or any other booster
source with an output greater than 12 Volts.
Do not allow cable clamps to touch each
other.
Battery posts, terminals, and related accesso -
ries contain lead and lead compounds. Wash
hands after handling.
CAUTION!
It is essential when replacing the cables on
the battery that the positive cable is attached
to the positive post and the negative cable is
attached to the negative post. Battery posts
are marked positive (+) and negative (-) and
are identified on the battery case. Cable
clamps should be tight on the terminal posts
and free of corrosion.
If a “fast charger” is used while the battery is
in the vehicle, disconnect both vehicle battery
cables before connecting the charger to the
battery. Do not use a “fast charger” to provide
starting voltage.
WARNING!
CAUTION!
Precautions have been taken to safeguard all
parts and connections however, the pressures
generated by these machines is such that
complete protection against water ingress
cannot be guaranteed.
WARNING!
You can be badly injured working on or around a
motor vehicle. Only do service work for which
you have the knowledge and the proper
equipment. If you have any doubt about your
ability to perform a service job, take your vehicle
to a competent mechanic.
8
23_DPF_OM_EN_USC_t.book Page 353

SERVICING AND MAINTENANCE357
Engine Air Cleaner Filter Installation
NOTE:Inspect and clean the housing if significant dirt or
debris is present before replacing the engine air
cleaner filter.
1. Install the engine air cleaner filter into the housing assembly with the engine air cleaner
filter inspection surface facing downward.
2. Install the engine air cleaner filter cover onto the housing assembly locating tabs.
3. Tighten the (6) screws to secure the engine air cleaner filter cover to the housing assembly.
AIR CONDITIONER MAINTENANCE
For best possible performance, your air conditioner
should be checked and serviced by an authorized
dealer at the start of each warm season. This
service should include cleaning of the condenser
fins and a performance test. Drive belt tension
should also be checked at this time.
Refrigerant Recovery And Recycling
R-134a — If Equipped
R-134a Air Conditioning Refrigerant is a Hydrofluo -
rocarbon (HFC) that is an ozone-friendly
substance. The manufacturer recommends that
air conditioning service be performed by an
authorized dealer or other service facilities using
recovery and recycling equipment.
NOTE:Use only manufacturer approved A/C system PAG
compressor oil and refrigerants.
Refrigerant Recovery And Recycling
R-1234yf — If Equipped
R-1234yf Air Conditioning Refrigerant is a Hydroflu -
oroolefin (HFO) that is endorsed by the
Environmental Protection Agency and is an
ozone-friendly substance with a low
global-warming potential. The manufacturer
recommends that air conditioning service be
performed by an authorized dealer using recovery
and recycling equipment.
NOTE:Use only manufacturer approved A/C system PAG
compressor oil, and refrigerants.
CAUTION!
Do not overtighten the engine air cleaner filter
cover lid screws or damage may result.
WARNING!
Use only refrigerants and compressor lubri -
cants approved by the manufacturer for your
air conditioning system. Some unapproved
refrigerants are flammable and can explode,
injuring you. Other unapproved refrigerants or
lubricants can cause the system to fail,
requiring costly repairs. Refer to Warranty
Information Book, for further warranty infor -
mation.
The air conditioning system contains refrig -
erant under high pressure. To avoid risk of
personal injury or damage to the system,
adding refrigerant or any repair requiring lines
to be disconnected should be done by an
experienced technician.
CAUTION!
Do not use chemical flushes in your air
conditioning system as the chemicals can
damage your air conditioning components. Such
damage is not covered by the New Vehicle
Limited Warranty.8
23_DPF_OM_EN_USC_t.book Page 357

SERVICING AND MAINTENANCE363
1. Ensure engine is turned off.
2. Place drain pan under the fuel filter drain hose.
3. Open the water drain valve one full turn counterclockwise and completely drain fuel
and water into the approved container.
4. Close the water drain valve.
5. Remove lid using a socket or strap wrench. Rotate counterclockwise for removal. Remove
used o-ring and discard it.
6. Remove the used filter cartridge from the housing and dispose of according to your local
regulations.
7. Wipe clean the sealing surfaces of the lid and housing.
8. Install new o-ring back into ring groove on the filter housing and lubricate with clean engine
oil.
NOTE:Water In Fuel (WIF) sensor is re-usable. Service kit
comes with new o-ring for filter canister and WIF
sensor.
PRIMING IF THE ENGINE HAS RUN OUT
O
F FUEL
1. Add a substantial amount of fuel to the tank,
approximately 2 to 5 gal (8 L to 19 L).
2. Three priming cycles must be completed. Turn ignition to the RUN position and wait approxi -
mately 30 seconds. This will activate the in
tank fuel pump. Turn the ignition switch to the
off position, and leave off for at least 30
seconds. Repeat this procedure three times
before cranking the engine.
3. Start the engine using the “Normal Starting” procedure Ú page 117.
4. Once the engine starts, allow the engine to idle for a minimum of 30 seconds.
NOTE:The engine may run rough until the air is forced
from all the fuel lines.
WARNING!
Do not open the high pressure fuel system with
the engine running. Engine operation causes
high fuel pressure. High pressure fuel spray can
cause serious injury or death.
CAUTION!
Do not engage the starter motor for more than
15 seconds at a time. Allow two minutes
between the cranking intervals.
WARNING!
Do not use alcohol or gasoline as a fuel blending
agent. They can be unstable under certain
conditions and be hazardous or explosive when
mixed with diesel fuel.
CAUTION!
Due to lack of lubricants in alcohol or gasoline,
the use of these fuels can cause damage to the
fuel system.
8
23_DPF_OM_EN_USC_t.book Page 363

SERVICING AND MAINTENANCE371
(Continued)
To guarantee optimum performance of the system,
keep the surfaces of the charge air cooler,
condenser and radiator clean and free of debris.
Periodically check the hoses leading to and from
the charge air cooler for cracks or loose clamps
resulting in loss of pressure and reduced engine
performance.
BRAKE SYSTEM
In order to ensure brake system performance, all
brake system components should be inspected
periodically Ú
page 344.
Fluid Level Check — Brake Master Cylinder
The fluid level of the master cylinder should be
checked when performing under the hood service
or immediately if the Brake System Warning Light
indicates system failure.
If necessary, add fluid to bring level within the
designated marks on the side of the reservoir of
the brake master cylinder. Be sure to clean the top
of the master cylinder area before removing cap.
With disc brakes the fluid level can be expected to
fall as the brake linings wear. However, an
unexpected drop in fluid level may be caused by a
leak and a system check should be conducted.
For further information Ú page 421.
WARNING!
Riding the brakes can lead to brake failure and
possibly a collision. Driving with your foot resting
or riding on the brake pedal can result in
abnormally high brake temperatures, excessive
lining wear, and possible brake damage. You
would not have your full braking capacity in an
emergency.
WARNING!
Use only manufacturer's recommended brake
fluid Úpage 421. Using the wrong type of
brake fluid can severely damage your brake
system and/or impair its performance. The
proper type of brake fluid for your vehicle is
also identified on the original factory installed
hydraulic master cylinder reservoir.
To avoid contamination from foreign matter or
moisture, use only new brake fluid or fluid that
has been in a tightly closed container. Keep
the master cylinder reservoir cap secured at
all times. Brake fluid in an open container
absorbs moisture from the air resulting in a
lower boiling point. This may cause it to boil
unexpectedly during hard or prolonged
braking, resulting in sudden brake failure. This
could result in a collision.
Overfilling the brake fluid reservoir can result
in spilling brake fluid on hot engine parts,
causing the brake fluid to catch fire. Brake
fluid can also damage painted and vinyl
surfaces, care should be taken to avoid its
contact with these surfaces.
Do not allow petroleum based fluid to contam -
inate the brake fluid. Brake seal components
could be damaged, causing partial or
complete brake failure. This could result in a
collision.
WARNING!
8
23_DPF_OM_EN_USC_t.book Page 371

400SERVICING AND MAINTENANCE
NOTE:Wheel valve stem must be replaced as well when
installing new tires due to wear and tear in existing
tires.
Keep dismounted tires in a cool, dry place with as
little exposure to light as possible. Protect tires
from contact with oil, grease, and gasoline.
Replacement Tires
The tires on your new vehicle provide a balance of
many characteristics. They should be inspected
regularly for wear and correct cold tire inflation
pressures. The manufacturer strongly
recommends that you use tires equivalent to the
originals in size, quality and performance when
replacement is needed Úpage 399. Refer to the
Tire And Loading Information Placard or the
Vehicle Certification Label for the size designation
of your tire. The Load Index and Speed Symbol for
your tire will be found on the original equipment
tire sidewall.
For more information relating to the Load Index
and Speed Symbol of a tire Ú page 389.
It is recommended to replace the two front tires or
two rear tires as a pair. Replacing just one tire can
seriously affect your vehicle’s handling. If you ever
replace a wheel, make sure that the wheel’s
specifications match those of the original wheels. It is recommended you contact an authorized tire
dealer or original equipment dealer with any
questions you may have on tire specifications or
capability. Failure to use equivalent replacement
tires may adversely affect the safety, handling, and
ride of your vehicle.
TIRE TYPES
All Season Tires — If Equipped
All Season tires provide traction for all seasons
(Spring, Summer, Autumn, and Winter). Traction
levels may vary between different all season tires.
All season tires can be identified by the M+S, M&S,
M/S or MS designation on the tire sidewall. Use all
season tires only in sets of four; failure to do so
may adversely affect the safety and handling of
your vehicle.
Summer Or Three Season Tires —
If Equipped
Summer tires provide traction in both wet and dry
conditions, and are not intended to be driven in
snow or on ice. If your vehicle is equipped with
Summer tires, be aware these tires are not
designed for Winter or cold driving conditions.
Install Winter tires on your vehicle when ambient
temperatures are less than 40°F (5°C) or if roads
are covered with ice or snow. For more
information, contact an authorized dealer.
WARNING!
Do not use a tire, wheel size, load rating, or
speed rating other than that specified for your
vehicle. Some combinations of unapproved
tires and wheels may change suspension
dimensions and performance characteristics,
resulting in changes to steering, handling, and
braking of your vehicle. This can cause unpre
-
dictable handling and stress to steering and
suspension components. You could lose
control and have a collision resulting in
serious injury or death. Use only the tire and
wheel sizes with load ratings approved for
your vehicle.
Never use a tire with a smaller load index or
capacity, other than what was originally
equipped on your vehicle. Using a tire with a
smaller load index could result in tire over -
loading and failure. You could lose control and
have a collision.
Failure to equip your vehicle with tires having
adequate speed capability can result in
sudden tire failure and loss of vehicle control.
CAUTION!
Replacing original tires with tires of a different
size may result in false speedometer and
odometer readings.
23_DPF_OM_EN_USC_t.book Page 400

429
B
Back Up Camera
............................................ 166Back-Up......................................................... 166Battery................................................. 104, 352Blanket...................................................... 123Charging System Light............................... 104Keyless Key Fob Replacement.................... 16Battery Saver Feature...................................... 55Belts, Seat..................................................... 322Blind Spot Assist Cameras............................. 277Bluetooth Connecting To A Particular Mobile PhoneOr Audio Device After Pairing
................238Body Builders Guide........................................ 10Body Mechanism Lubrication........................ 364B-Pillar Location............................................. 394Brake Assist System...................................... 271Brake Control System.................................... 271Brake Fluid.......................................... 371, 421Brake System...................................... 371, 411Fluid Check............................................... 371Master Cylinder......................................... 371Parking...................................................... 128Warning Light............................................ 103Brake/Transmission Interlock....................... 131Bulb Replacement......................................... 384Bulbs, Light.......................................... 324, 384
C
Cab Top Clearance Lights............................. 388Camera......................................................... 166Camera, AUX........................................ 173, 176Camera, Rear....................................... 166, 168Camera, Trailer Surround View..................... 173Capacities, Antifreeze (Engine Coolant)........ 418Capacities, Fluid........................................... 418Caps, FillerOil (Engine)............................................... 350Power Steering......................................... 148Radiator (Coolant Pressure)..................... 369Car Washes................................................... 408Carbon Monoxide Warning............................ 324Cargo Light....................................................... 54CD................................................................. 232Cellular Phone.............................................. 263Center High Mounted Stop Light................... 388Center Seat Storage Compartment.................. 66Changing A Flat Tire...................................... 329Charge Air Cooler.......................................... 370Chart, Tire Sizing........................................... 390Check Engine Light
(Malfunction Indicator Light)......................... 112Checking Your Vehicle For Safety................. 321Checks, Safety.............................................. 321Child Restraint.............................................. 305
Child RestraintsBooster Seats........................................... 308Child Seat Installation...................... 315, 317How To Stow An unused ALR Seat Belt..... 313Infant And Child Restraints....................... 307Locating The LATCH Anchorages.............. 312Lower Anchors And Tethers For Children.. 310Older Children And Child Restraints.......... 308Seating Positions...................................... 309Clean Air Gasoline......................................... 413CleaningWheels...................................................... 403Climate Control................................................58Automatic....................................................59Manual........................................................62Cold Weather Operation................................ 117Compact Spare Tire...................................... 401Connected Services...................................... 244Connected Services FAQ............................... 258Connected Services Features....................... 247Connected Services, Getting Started............ 246Connected Services, Introduction................. 244Contract, Service........................................... 424Controls........................................................ 224Cooling Pressure Cap (Radiator Cap)............ 369
11
23_DPF_OM_EN_USC_t.book Page 429

430 Cooling System
.............................................. 368Adding Coolant (Antifreeze)....................... 369Coolant Level.................................. 368, 370Cooling Capacity........................................ 418Disposal Of Used Coolant.......................... 370Drain, Flush, And Refill.............................. 368Inspection................................................. 370Points To Remember................................. 370Pressure Cap............................................. 369Radiator Cap............................................. 369Selection Of Coolant (Antifreeze)..... 368, 419Corrosion Protection...................................... 407Cruise Control (Speed Control)... 148, 149, 150Cruise Light................................................... 110Customer Assistance..................................... 422Cybersecurity................................................. 199
D
Daytime Running Lights................................... 52Dealer Service............................................... 353Defroster, Rear Window................................... 62Defroster, Windshield............................. 62, 322Delay (Intermittent) Wipers.............................. 57Deleting A Phone........................................... 238Diagnostic System, Onboard......................... 111Diesel Exhaust Brake.................................... 129Diesel Fuel..................................................... 415Diesel Fuel Requirements............................. 415Diesel Fuel System, Re-Priming..................... 363Differential, Limited Slip................................ 147
Dipsticks Power Steering......................................... 148Disabled Vehicle Towing............................... 339Disc Drive..................................................... 232Disconnecting............................................... 238DisposalAntifreeze (Engine Coolant)...................... 370Disturb.......................................................... 241Door Ajar....................................................... 105Door Ajar Light.............................................. 105Door LocksAutomatic.................................................... 27Doors............................................................... 24Draining Fuel/Water Separator Filter............ 360Driver Memory Presets................................. 230Driver’s Seat Back Tilt...................................... 31DrivingThrough Flowing, Rising, Or Shallow Standing Water
................................................... 198Dual Rear Wheels....................... 332, 406, 411
E
Electric Brake Control System....................... 271Anti-Lock Brake System............................ 270Electronic Roll Mitigation................. 272, 277Electrical Power Outlets................................... 71Electronic Range Select (ERS)............. 134, 137Electronic Stability Control (ESC).................. 272Electronic Throttle Control Warning Light...... 104Electronically Shifted Transfer Case.... 140, 143
Emergency Braking.............................. 128, 280Emergency, In Case OfFreeing Vehicle When Stuck..................... 338Hazard Warning Flasher........................... 325Jacking...................................................... 329Jump Starting........................................... 333Emission Control System Maintenance......... 112Engine.................................................. 350, 351Air Cleaner................................................ 355Block Heater............................................. 119Break-In Recommendations............ 127, 128Compartment........................................... 351Compartment Identification...................... 350Coolant (Antifreeze).................................. 419Exhaust Gas Caution................................ 324Fails To Start............................................. 116Flooded, Starting...................................... 116Fuel Requirements................................... 413Identification............................................. 351Idling......................................................... 124Jump Starting........................................... 333Oil.................................................... 353, 419Oil Filler Cap............................................. 350Oil Filter.................................................... 354Oil Reset......................................................92Oil Selection.............................................. 353Oil Synthetic.............................................. 354Overheating.............................................. 335Runaway................................................... 176Starting..................................................... 115
23_DPF_OM_EN_USC_t.book Page 430