
14
Dashboard instruments
SCR emissions control system (BlueHDi)Fixed when the ignition is switched 
on, accompanied by an audible 
signal and a message.
A malfunction of the SCR emissions control 
system has been detected.
This alert disappears once the exhaust 
emissions return to normal levels.
Flashing AdBlue® warning lamp on 
switching on the ignition, with the 
Engine self-diagnostics warning lamp on fixed, 
accompanied by an audible signal and a 
message indicating the driving range.
Depending on the message displayed, it is 
possible to drive for up to 685 miles (1,100
  km) 
before the engine immobiliser is triggered.
Carry out (3) without delay, to  avoid starting 
being prevented.
Flashing AdBlue® warning lamp on 
switching on the ignition, with the 
Engine self-diagnostics warning lamp on fixed, 
accompanied by an audible signal and a 
message indicating that starting is prevented.
The engine immobiliser prevents the engine from 
restarting (the permitted driving limit has been 
exceeded after confirmation of a malfunction of 
the emissions control system).
To start the engine, carry out (2).
Automatic functions deactivated (electric 
parking brake)
Fixed.
The "automatic application" (on switching 
off the engine) and "automatic release" (on 
acceleration) functions are deactivated.
If automatic application/release is no longer 
possible:
►
 
Start the engine.
►
 
Use the control to apply the electric parking 
brake.
►
 
T
ake your foot fully off the brake pedal.
►
 
Hold the control pressed in the release 
direction for between 10 and 15
  seconds.
►
 
Release the control.
►
 
Depress and hold the brake pedal.
►
 
Pull the control in the application direction for 
2
 
seconds.
►
 
Release the control and the brake pedal.
Malfunction (with electric parking brake)Fixed, accompanied by the 
message "Parking brake fault".
The vehicle cannot be immobilised with the 
engine running.
If manual application and release commands are 
not working, the electric parking brake control is 
faulty.
The automatic functions must be used at all 
times and are automatically reactivated in the 
event of a fault with the control.
Carry out (2).
Fixed, accompanied by the 
message "Parking brake 
fault".
The electric parking brake is faulty: manual and 
automatic functions may not be working.
When stationary, to immobilise the vehicle:
►
 
Pull the electric parking brake control and 
hold it for approximately 7 to 15
  seconds, until 
the indicator lamp lights up on the instrument 
panel.
If this procedure does not work, secure the 
vehicle:
►
 
Park on a level surface.
►
 
Select mode
 
P on the automatic gearbox, 
then place the supplied chock against one of the 
wheels.
Then carry out (2).
BrakingFixed.
A minor fault with the braking system has 
been detected.
Drive carefully.
Carry out (3).
Collision Risk Alert/Active Safety BrakeFlashing.
The system activates and brakes the 
vehicle momentarily to reduce the speed of 
collision with the vehicle in front.
For more information, refer to the Driving 
section.   

18
Dashboard instruments
Black/white warning lamps
Foot on the brake
Fixed.
Insufficient or no pressure on the brake 
pedal.
With the engine running, before releasing the 
parking brake, to move out of mode  P on an 
automatic gearbox.
e-SAVE function (Rechargeable hybrid)Fixed, accompanied by the reserved 
electric range.
The function is activated.
Indicators
Service indicator
The servicing information is expressed in terms 
of distance (miles or kilometres) and time 
(months or days).
The alert is given at whichever of these two 
terms is reached first.
The servicing information is displayed in the 
instrument panel. Depending on the version of 
the vehicle:
–
 
The distance recorder display line indicates 
the distance remaining before the next service 
is due, or the distance travelled since it was due 
preceded by the "-" sign.
–
 
An alert message indicates the distance 
remaining, as well as the period before the next 
service is due or how long it is overdue.
The value indicated is calculated  according to the distance covered and 
the time elapsed since the last service.
The alert may also be triggered close to a 
due date.
Service spannerOn temporarily when the ignition is 
switched on.
Between 620 and 1,860 miles (1,000 and 3,000 
km) remain before the next service is due.
Fixed, when the ignition is switched on.
The next service is due in less than 620 
miles (1,000 km).
Have your vehicle serviced very soon.
Service spanner flashingFlashing then fixed, when the 
ignition is switched on.
(With
 
BlueHDi   Diesel engines, associated with 
the Service warning lamp.)
The servicing interval has been exceeded.
Have your vehicle serviced as soon as possible.
Resetting the service indicator
The service indicator must be reset after each 
service.
If you have serviced your vehicle yourself:
►
 
Switch the ignition off.
 
 
 
 
► Press and hold the button located on the end 
of the lighting control stalk.
►
 
Without pressing the brake pedal, press the 
ST
ART/STOP button once; a temporary display 
window appears and a countdown begins.
►
 
When the display indicates  =0
, release the 
lighting control stalk button; the spanner symbol 
disappears.
If you disconnect the battery following 
this operation, lock the vehicle and wait 
at least 5 minutes for the reset to be 
registered.
Reminder of the servicing information
Servicing information is accessible using 
the Settings   > Vehicle application on the 
touch screen.
►
 
Then select 
 Safety   > Diagnostics.
Engine oil level indicator
(Depending on version)   

19
Dashboard instruments
1On versions fitted with an electric gauge, the 
engine oil level status is displayed on the 
instrument panel for a few seconds when 
the ignition is switched on, after the servicing 
information, in the form of messages.
The level read will only be correct if the vehicle is on level ground and the engine 
has been off for more than 30 minutes.
Low oil level
This is indicated by a message prompting you to 
top up the level, accompanied by the lighting of 
the Service warning lamp and an audible signal.
If a low oil level is confirmed by a check using 
the dipstick, the level must be topped up to avoid 
damage to the engine.
For more information on  Checking levels, refer 
to the corresponding section.
Oil gauge malfunction
This is indicated by the message " Oil level 
measurement invalid" on the instrument panel.
Consult a PEUGEOT dealer or a qualified 
workshop.
In the event of a malfunction of the 
electric gauge, the oil level is no longer 
monitored.
If the system is faulty, you must check the 
engine oil level using the manual dipstick 
located in the engine compartment.
For more information on  Checking levels, 
refer to the corresponding section.
Coolant temperature 
indicator
 
 
With the engine running:
–  In zone  A, the temperature is correct.
–
 
In zone 
 B, the temperature is too high. The 
associated warning lamp and the  STOP
  warning 
lamp light up in red on the instrument panel, 
accompanied by the display of a message and 
an audible signal.
You must stop the vehicle as soon as it is 
safe to do so.
Wait a few minutes before switching off the 
engine.
After switching off the ignition, carefully  open the bonnet and check the coolant 
level.
For more information on  Checking 
levels, refer to the corresponding 
section.
AdBlue® range indicators 
(BlueHDi)
The Diesel BlueHDi engines are equipped with 
a system that associates the SCR (Selective 
Catalytic Reduction) emissions control system 
and the Diesel particle filter (DPF) for the 
treatment of exhaust gases. They cannot 
function  without AdBlue
® fluid.
When the level of AdBlue® falls below the 
reserve level (between 1,500 and 0 miles (2,400 
and 0
 
km)), a warning lamp lights up when 
the ignition is switched on and an estimate 
of the distance that can be travelled before 
engine starting is prevented is displayed in the 
instrument panel.
The engine starting prevention system  required by regulations is activated 
automatically once the AdBlue
® tank is empty. 
It is then no longer possible to start the 
engine until the minimum level of AdBlue
® has 
been topped up.
Manual display of driving range
While the driving range is greater than 
1,500 miles (2,400   km), it is not displayed 
automatically.
Driving range information is accessible 
using the Settings   > Vehicle application 
on the touch screen.
►
 
Then select 
 Safety   > Diagnostics.   

22
Dashboard instruments
The test is launched in the Settings> Vehicle touch screen application.
►
 
Then select 
 Safety > Diagnostics.
The following information is displayed on the 
instrument panel:
–
 
T
yre pressures.
–
 
Engine oil level (depending on engine).
–
 
Next service due.
–
 
Driving range associated with the
  
AdBlue® and 
the SCR system (BlueHDi
 
Diesel).
–
 
Current alerts.
This information is also displayed  automatically every time the ignition is 
switched on.
Total distance recorder
The total distance recorder measures the total 
distance travelled by the vehicle since its initial 
registration.
With the ignition on, the total distance is 
displayed at all times. It remains displayed for 
30
  seconds after switching off the ignition. It is 
displayed when the driver's door is opened, and 
when the vehicle is locked or unlocked.
When travelling abroad, you may have to 
change the distance units (miles or km): 
the displayed speed must be in the local 
country’s official unit (mph or km/h).
The unit is changed via the screen's 
configuration application, with the vehicle 
stationary.
Rechargeable hybrid vehicles
The total distance recorder is only 
accessible from the trip computer.
For more information on the  Trip computer, 
refer to the corresponding section.
Lighting dimmer
Used to manually adjust the brightness of the 
instruments and controls to suit the exterior light 
level.
It is configured in the Settings > 
Brightness  touch screen application.
►
 
In the "
 Cockpit"   category, press or move the 
slider to the desired setting.
Trip computer
Displays information related to the current trip 
(range, fuel consumption, average speed, etc.).
Data displayed on the 
instrument panel
Trip computer data is permanently displayed 
when the "Personal" display mode is selected. In all other display modes, pressing the end of 
the wiper control stalk will cause this data to 
appear temporarily in a specific window.
Displaying the different tabs
 
 
 
 
► Pressing the button located on the end of the 
wiper control stalk displays the following tabs in 
turn:
–
 
Current information:
•
 
T
 otal driving range (Petrol or Diesel).
•
 
Current consumption (Petrol or Diesel).
•
 
T
 ime counter for Stop & Start (Petrol or 
Diesel).
•
 
Percentage of the current journey travelled 
in all-electric driving mode (Rechargeable 
hybrid).
–
 
T
 rips "1" then "2":
•
 
A
 verage speed.
•
 
A
 verage fuel consumption.
•
 
Distance travelled.
Trip reset
► When the desired trip is displayed, 
press the button on the end of the wiper 
control stalk for more than 2
  seconds.   

23
Dashboard instruments
1Trips "1" and "2" are independent and are used 
in the same way.
Definitions
Range
(miles or km)Distance that can still be travelled with the 
fuel remaining in the tank (based on the 
average fuel consumption over the last few miles 
(kilometres) travelled).
This value may vary following a change in driving 
style or terrain, leading to a significant change in 
current fuel consumption.
When the range falls below 19 miles (30
  km), 
dashes are displayed.
After filling with at least 5 litres of fuel, the range 
is recalculated and is displayed if it exceeds 62 
miles (100
  km).
Dashes appearing permanently in place of 
numbers while driving indicates a malfunction.
Consult a PEUGEOT dealer or a qualified 
workshop.
Current consumption
(mpg or l/100 km or km/l)Calculated during the last few seconds. 
This function is only displayed at speeds above 
19 mph (30
  km/h).
Average consumption
(mpg or l/100 km or km/l)
Calculated since the last trip computer 
reset.
Average speed
(mph or km/h)Calculated since the last trip computer 
reset.
Distance travelled
(miles or km)Calculated since the last trip computer 
reset.
Stop & Start time counter
(minutes/seconds or hours/minutes) 
If your vehicle is fitted with the Stop & Start 
function, a time counter calculates the time spent 
in STOP mode during a journey.
The time counter is reset each time the ignition is 
switched on.
10-inch touch screen
This system gives access to the following  elements:
–
 
T
 ime and exterior temperature.
–
 
Heating/air conditioning system controls and 
reminders of settings.
–
 
Settings for driving aid functions, comfort and 
safety functions, audio equipment and digital 
instrument panel.
– Settings of functions specific to rechargeable 
hybrid vehicles.
–
 
Display of visual manoeuvring aid functions.
–
 
Interactive handbook.
–
 
V
 ideo tutorials (e.g.   screen management, 
driving aids, voice recognition).
–
 
Audio equipment and telephone controls with 
display of
  associated information.
–
 
Connected services and display of associated 
information.
–
 
Navigation system controls and display 
of associated information (depending on 
equipment).
–
 
V
 oice recognition (depending on equipment).
For safety reasons, always stop the 
vehicle before performing operations 
that require sustained attention.
Some functions are not accessible while 
driving.
Recommendations
This screen uses capacitive sensing technology.
–  Do not use pointed objects on the touch 
screen.
–
 
Do not touch the touch screen with wet hands.
–
 
Use a soft, clean cloth to clean the touch 
screen.
Main controls
Access to one of the home pages Return to the first home page   

24
Dashboard instruments
Direct access to the Climate application 
Direct access to the Shortcuts for 
driving aids
►
 
Swipe down from the upper edge of the touch 
screen to access a list of quick settings (e.g. 
Brightness
, Diagnostics).
►
 
Depending on the pages displayed on the 
screen, with or without the context menu, scroll 
the text by swiping with your finger
, as with a 
smartphone.
From any page, press the touch screen 
with three fingers to display the 
applications wall.
Show/Hide context menu 
Return to the previous page 
►
 
T
o change the status of a function, press the 
description for the corresponding line (change 
confirmed by the slider moving to the right/left: 
function activated/deactivated).
Access additional information on the  function
Access to function parameters 
Adding/Removing shortcuts 
Short press, ignition off: system on/off.
Short press, ignition on: mute/restore 
sound. Long press, ignition on: start standby mode 
(mute sound, screens and clock display off).
Rotation: volume adjustment.
Applications
Press this button to access the 
applications wall.
To obtain information about the other 
applications not listed here, refer to the sections 
describing the audio and telematic systems.
ADAS
Activation/Deactivation and configuration 
of the driving aid functions.
Climate
Settings for temperature, air flow, etc.
For more information on  Dual-zone automatic 
air conditioning , refer to the corresponding 
section.
Seats
Activation/Deactivation and configuration 
of the seat comfort functions (massages).
For more information on the  Multi-point 
massages , refer to the corresponding section.
Settings
Main settings for the audio system, touch 
screen and digital instrument panel.
Activation/Deactivation and configuration of 
the exterior lighting, vehicle access and safety 
functions.
Energy
Access to the rechargeable hybrid system 
features (energy flow, consumption statistics, 
deferred charging, e
- SAVE function).
Energy application
Energy Flow
The page shows the operation of the 
rechargeable hybrid system in real time.
1.Active driving mode
2. Petrol engine
3. Electric motor(s)
4. Traction battery charge level
The energy flows have a specific colour for each 
type of driving: 
–
 
Blue: 100% electrical energy
 .
–
 
White: energy from the petrol engine.
–
 
Green: energy recovery
 .
Statistics
This page shows electrical energy and fuel 
consumption statistics.
 
    

25
Dashboard instruments
11. Average electrical consumption for the current 
trip (kWh/100  km) and historical values:
–
 
Blue graph: energy consumed directly from 
the traction battery
.
–
 
Green graph: energy regenerated during 
deceleration and braking phases used to 
recharge the
  traction   battery.
2. Average fuel consumption for the current trip 
(l/100
  km) and historical values (orange graph).
Charging
This page allows you to programme deferred 
charging.
For more information on  Charging the traction 
battery (Rechargeable hybrid), refer to the 
corresponding section.
e-SAVE
The e-SAVE function makes it possible to 
reserve all or part of the electrical energy of the 
traction battery to be used later during a journey 
(e.g.
  passing through an urban area or an area 
reserved for electric vehicles).
►
 
Activate the function by pressing  ON
, then 
select the electric range to be reserved ( 6 miles 
(10 km), 12 miles (20 km)  or the full range 
MAX).
Activation of the function is confirmed by  the lighting of this indicator lamp on the 
instrument panel and the indication of the energy 
reserve in miles or kms.
►
 
T
o use the energy reserve, choose the 
Electric driving mode in the mode selector.
If the requested range exceeds the 
available range (not recommended), the 
internal combustion engine starts to recharge 
the traction battery up to the requested 
threshold. This leads to excessive fuel 
consumption.
Remotely operable 
additional functions 
(Rechargeable hybrid)
(Depending on country of sale) 
 
The following functions are 
available from the  MYPEUGEOT 
APP application, which is 
accessible from a smartphone:
–
 
Managing the traction battery charging 
(deferred charging).
–
 
Managing the temperature pre-conditioning.
–
 
V
iewing the state of charge and range of the 
vehicle.
Installation procedure
► Download the  MYPEUGEOT  APP application 
from the appropriate online store for your 
smartphone.
►
 
Create an account.
►
 
Enter the vehicle identification number 
(available on the vehicle registration certificate).
For more information on  Identification 
markings, refer to the corresponding section.
Network coverage
In order to be able to use the various 
remotely operable features, ensure that your 
vehicle is located in an area covered by the 
mobile network.
A lack of network coverage may prevent 
communication with the vehicle (for example, 
if it is in an underground car park). In such 
cases, the application will display a message 
indicating that the connection with the vehicle 
could not be established.   

31
Access
2Central locking not 
functioning
Use these procedures in the following cases:
– Central locking malfunction.
–
 
Battery disconnected or discharged.
In the event of a malfunction of the 
central locking system, the battery must 
be disconnected to ensure that the vehicle is 
locked fully.
Front left-hand door
► Insert the key into the door lock.
►  T urn the key towards the rear of the vehicle 
to lock it, or towards the front to unlock it.
Other doors
Unlocking
► Pull the interior door opening control.
Locking 
 
► Open the doors.
►  For the rear doors, check that the child lock 
is not on.
Refer to the corresponding section.
►
 
Remove the black cap
 , located on the edge 
of the door, using the key.
►
 
Insert the key into the socket without forcing 
it, then turn the latch towards the inside of the 
door
.
►
 
Remove the key and refit the black cap.
►
 
Close the doors and check from the outside 
that the vehicle is locked.
Changing the battery
A message is displayed on the instrument panel 
when the battery needs changing.
Battery type: CR2032/3 volts. 
 
► Unclip the cover by inserting a small 
screwdriver in the slot and lift the cover .
►
 
Remove the flat battery from its housing.
►
 
Put the new battery in place, respecting the 
polarity
. Start by inserting it into the contacts 
located in the corner, then clip the cover onto 
the unit.
►
 
Reinitialise the remote control.
For more information on  Reinitialising the 
remote control
, refer to the corresponding 
section.
Do not throw remote control batteries 
away, as they contain metals that are 
harmful to the environment. Take them to an 
approved disposal point.