2023 MAZDA MODEL CX-50 steering

Seat Ventilation*
▼Seat Ventilation
The seat ventilation uses the fans
installed on the seats to draw air
around the seat surface and ventilate
them. The ignition must be switched
ON.
While the seat ventilation is operating ,
the indicator light in the seat
ventilation switch turns on according
to the set mode.
Manual mode
When the seat ventilation switch is
pressed, the seat ventilation operates
in manual mode.
The mode changes as shown in the
figure each time the seat ventilation
switch is pressed.
1. OFF
2. High
3. Mid
4. Low
NOTE
If the engine is turned off while the
seat ventilation is operating in manual
mode, the seat ventilation does not
turn on automatically the next time the
engine is turned on. To turn the seat
ventilation on, press the switch again.
Auto mode
The seat ventilation can be operated in
conjunction with auto mode for the
climate control system.
Auto mode operates when auto mode
is enabled in the Mazda Connect
settings.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Press the AUTO switch to select auto
mode.
While operating in auto mode, the
(with heated steering wheel)/
(without heated steering wheel) is
displayed.
Refer to Fully Automatic Type on page
5-10.
The seat mode is automatically
controlled at 4 levels (High, Mid, Low,
and OFF) according to the conditions
in the cabin.
CAUTION

Do not use organic solvents to clean
the seat. It may damage the seat
surface and the seat ventilation
parts.
 Do not place heavy objects with
sharp projections on the seat, or
insert needles or pins into it.
Essential Safety Equipment
Seat Warmer/Seat Ventilation/Heated Steering Wheel
*Some models.2-19
CX-50_8KB8-EA-22A_Edition2_new 2022-1-6 14:55:18

NOTE
If the front passenger’s seat belt is
unfastened, the front passenger’s
seat ventilation turns off.
If any of the following switch
operations is performed during auto
mode or the auto operation of the
climate control system is canceled,
the seat ventilation switches from
auto mode to manual mode.
Seat warmer switch is pressedSeat ventilation switch is pressed
When the seat warmer switch/seat
ventilation switch is pressed, only the
seat on the side where the switch
was pressed switches to manual
mode.
To return to auto operation, press
the AUTO switch for the climate
control system.
If the engine is turned off while the
seat ventilation is operating in auto
mode, the seat ventilation operates
in auto mode again the next time the
engine is turned on.
Use the seat ventilation when the
engine is running. Leaving the seat
ventilation on for long periods with
the engine not running could cause
the battery power to be depleted.
(Vehicles with seat warmer)
The seat ventilation cannot be used
at the same time as the seat warmer.
Heated Steering Wheel*
▼ Heated Steering Wheel
The grips on the left and right of the
steering wheel can be warmed up
when the ignition is switched ON.
While the heated steering wheel is
operating , the indicator light in the
heated steering wheel switch turns on.
1. Heated steering wheel switch
2. Heating area

Manual mode
The heated steering wheel operates for
about 30 minutes when the heated
steering wheel switch is pressed, and
then automatically turns off.
To turn the heated steering wheel off
manually, press the switch again.
Auto mode
The heated steering wheel can be
operated in conjunction with auto
mode for the climate control system.
Auto mode operates when auto mode
is enabled in the Mazda Connect
settings.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Press the AUTO switch to select auto
mode.
While operating in auto mode, the
is displayed.
Essential Safety Equipment
Seat Warmer/Seat Ventilation/Heated Steering Wheel
2-20*Some models.
CX-50_8KB8-EA-22A_Edition2_new
2022-1-6 14:55:18

Refer to Fully Automatic Type on page
5-10.
The heated steering wheel
automatically operates/turns off
according to the conditions in the
cabin.
NOTE
If the heated steering wheel switch is
pressed during auto mode or the
auto operation of the climate control
system is canceled, the heated
steering wheel switches from auto
mode to manual mode.
To return to auto operation, press
the AUTO switch for the climate
control system.
If the ignition is switched OFF while
the heated steering wheel is
operating in auto mode, the heated
steering wheel operates in auto
mode again the next time the
ignition is switched ON.

CAUTION
The following types of persons should
be careful not to touch the steering
wheel. Otherwise, it could cause a
low-temperature burn.
 Infants, small children, elderly
people, and physically challenged
people
 People with delicate skin
 People who are excessively fatigued
 People who are intoxicated
 People who have taken
sleep-inducing medicine such as
sleeping pills or cold medicine
Essential Safety Equipment
Seat Warmer/Seat Ventilation/Heated Steering Wheel
2-21
CX-50_8KB8-EA-22A_Edition2_new 2022-1-6 14:55:18

Supplemental Restraint
System (SRS) Precautions
▼ Supplemental Restraint System
(SRS) Precautions
The front and side supplemental
restraint systems (SRS) include
different
types of air bags. Please verify the
different types of air bags which are
equipped on your vehicle by locating
the “SRS AIRBAG” location indicators.
These indicators are visible in the area
where the air bags are installed.
The air bags are installed in the
following locations:

The steering wheel hub (driver air
bag)
The front passenger dashboard (front
passenger air bag)
Under the instrument panel (driver
and front passenger* knee air bags)The outboard sides of the front
seatbacks (side air bags for driver
and front passenger)
The outboard sides of the rear
seatbacks (side air bags for rear
passengers)
*
The front and rear window pillars,
and the roof edge along both sides
(curtain air bags)

Vehicles with the Driver and Front
Passenger Occupant Classification
System have a sensor which detects an
impending roll-over accident.

The air bag supplemental restraint
systems are designed to provide
supplemental protection in certain
situations so seat belts are always
important in the following ways:

Without seat belt usage, the air bags
cannot provide adequate protection
during an accident. Seat belt usage is
necessary to:
Keep the occupant from being
thrown into an inflating air bag.
Reduce the possibility of injuries
during an accident that is not
designed for air bag inflation, such as
rear impact.
Reduce the possibility of injuries in
frontal, near frontal or side collisions
or roll-over accidents that are not
severe enough to activate the air
bags.
Reduce the possibility of being
thrown from your vehicle.
Reduce the possibility of injuries to
lower body and legs during an
accident.
Hold the driver in a position which
allows better control of the vehicle.

If your vehicle is also equipped with a
driver and front passenger occupant
classification system, refer to the Front
Passenger Occupant Classification
System (page 2-67) for details.
If your vehicle is equipped with a driver
and front passenger occupant
classification system, the front
passenger air bag deactivation
indicator light illuminates for a
Essential Safety Equipment
SRS Air Bags
2-52*Some models.
CX-50_8KB8-EA-22A_Edition2_new 2022-1-6 14:55:18

Do not sit too close to the driver and
front passenger air bags:
Sitting too close to the driver and front
passenger air bag modules or placing
hands or feet on them is extremely
dangerous. The driver and front
passenger air bags inflate with great
force and speed. Serious injuries could
occur if someone is too close. The
driver should always hold onto only the
rim of the steering wheel. The front
seat passenger should keep both feet
on the floor. Front seat occupants
should adjust their seats as far back as
possible and always sit upright against
the seatbacks with seat belts worn
properly.
Sit in the center of the seat and wear
seat belts properly:
Sitting too close to the side air bag
modules or placing hands on them, or
sleeping up against the door or
hanging out the windows is extremely
dangerous. The side and curtain air
bags inflate with great force and speed
directly expanding along the door on
the side the car is hit. Serious injury
could occur if someone is sitting too
close to the door or leaning against a
window, or if rear seat occupants grab
the sides of the front seatbacks. Give
the side and curtain air bags room to
work by sitting in the center of the seat
while the vehicle is moving with seat
belts worn properly.
Do not attach objects on or around
the area where air bags deploy:Attaching objects to the air bags or
placing something in the area where
the air bags deploy is dangerous. In an
accident, an object could interfere with
air bag inflation and injure the
occupants. Furthermore, the bag could
be damaged causing gases to release.
Always keep the deployment area of
the air bag modules free of any
obstructions.
For example, you should not do any of
the following as it may interfere with
air bag deployment.
 Do not put a covering on or lean
anything against areas such as the
dashboard and lower portion of the
instrument panel that blocks the
passenger front air bag and knee air
bags.
 Do not use seat covers on the front
seats and rear seats equipped with
in-seat side air bags.
 Do not hang any backpacks, bags or
pouches that cover the sides of the
seats that block the side air bags.
 Do not place any objects on the
assist grips. Only hang clothes
directly on the coat hooks.
Do not touch the components of the
supplemental restraint system after
the air bags have inflated:
Touching the components of the
supplemental restraint system after the
air bags have inflated is dangerous.
Immediately after inflation, they are
very hot. You could get burned.
Essential Safety Equipment
SRS Air Bags
2-54
CX-50_8KB8-EA-22A_Edition2_new 2022-1-6 14:55:18

Do not modify the supplemental
restraint system:
Modifying the components or wiring of
the supplemental restraint system is
dangerous. You could accidentally
activate it or make it inoperable. Do
not make any modifications to the
supplemental restraint system. This
includes installing trim, badges, or
anything else over the air bag modules.
It also includes installing extra
electrical equipment on or near system
components or wiring. An Authorized
Mazda Dealer can provide the special
care needed in the removal and
installation of front seats. It is
important to protect the air bag wiring
and connections to assure that the
bags do not accidentally deploy, and
that the front passenger occupant
classification system and the seats
retain an undamaged air bag
connection.
Do not place luggage or other objects
under the front seats:
Placing luggage or other objects under
the front seats is dangerous. The
components essential to the
supplemental restraint system could be
damaged, and in the event of a side
collision, the appropriate air bags may
not deploy, which could result in death
or serious injury. To prevent damage to
the components essential to the
supplemental restraint system, do not
place luggage or other objects under
the front seats.
Do not operate a vehicle with
damaged air bag/seat belt
pretensioner system components:Expended or damaged air bag/seat
belt pretensioner system components
must be replaced after any collision
which caused them to deploy or
damage them. Only a trained
Authorized Mazda Dealer can fully
evaluate these systems to see that they
will work in any subsequent accident.
Driving with an expended or damaged
air bag or pretensioner unit will not
afford you the necessary protection in
the event of any subsequent accident
which could result in serious injury or
death.
Do not remove interior air bag parts:
Removing any components such as the
front seats, front dashboard, the
steering wheel or parts on the front
and rear window pillars and along the
roof edge, containing air bag parts or
sensors is dangerous. These parts
contain essential ai r bag components.
The air bag could accidentally activate
and cause serious injuries. Always have
an Authorized Mazda Dealer remove
these parts.
Properly dispose of the air bag
system:
Improper disposal of an air bag or a
vehicle with live air bags in it can be
extremely dangerous. Unless all safety
procedures are followed, injury could
result. Have an Authorized Mazda
Dealer safely dispose of the air bag
system or scrap an air bag equipped
vehicle.
Essential Safety Equipment
SRS Air Bags
2-56
CX-50_8KB8-EA-22A_Edition2_new 2022-1-6 14:55:18

How the SRS Air BagsWork
▼How the SRS Air Bags Work
Your Mazda is equipped with the
following types of SRS air bags. SRS air
bags are designed to work together
with the seat belts to help to reduce
injuries during an accident.
The SRS air bags are designed to
provide further protection for
passengers in addition to the seat belt
functions. Be sure to wear seat belts
properly.
▼Seat Belt Pretensioners
The pretensioners operate differently
depending on what types of air bags
are equipped. For more details about
seat belt pretensioner operation, refer
to the SRS Air Bag Deployment Criteria
(page 2-63).
Front
The front seat belt pretensioners are
designed to deploy in moderate or
severe frontal, near frontal collisions.
In addition, the pretensioners operate
when a side collision or a roll-over
accident (with roll-over sensor) is
detected.
Rear Outboard
*
The rear outboard seat belt
pretensioners are designed to deploy
in moderate or severe frontal, near
frontal collisions.
In addition, the pretensioners operate
when a side collision or a roll-over
accident is detected.
▼
Driver Air Bag
The driver's air bag is mounted in the
steering wheel.
When air bag crash sensors detect a
frontal impact of greater than
moderate force, the driver's air bag
inflates quickly helping to reduce injury
mainly to the driver's head or chest
caused by directly hitting the steering
wheel.
For more details about air bag
deployment, refer to "SRS Air Bag
Deployment Criteria" (page 2-63).
(With Driver and Front Passenger
Occupant Classification System)
The inflation of the driver's dual-stage
air bag is controlled in two energy
stages depending on the driver's seat
position. The driver's seat slide
position sensor is located under the
driver's seat. The sensor determines
whether the driver's seat is forward of
or behind a reference position and
sends the seat position to the
diagnostic module (SAS unit). The SAS
unit is designed to control the
deployment of the driver's air bag
depending on how close the driver's
seat is to the steering wheel.
During an impact of moderate severity,
the driver's air bag deploys with lesser
energy, whereas during more severe
impacts and when the driver's seat is
behind the reference position, it
deploys with more energy.
Essential Safety Equipment
SRS Air Bags
2-60*Some models.
CX-50_8KB8-EA-22A_Edition2_new
2022-1-6 14:55:18

Driver and Front
Pa s s e n g e r O cc u p a n t
Classification System
*
▼ Driver and Front Passenger
Occupant Classification System
First, please read "Supplemental
Restraint System (SRS) Precautions"
(page 2-52) carefully.
▼Driver Seat Slide Position Sensor
Your vehicle is equipped with a driver
seat slide position sensor as a part of
the supplemental restraint system. The
sensor is located under the driver seat.
The sensor determines whether the
driver seat is fore or aft of a reference
position and sends the seat position to
the diagnostic module (SAS unit).
The SAS unit is designed to control the
deployment of the driver air bag
depending on how close the driver
seat is to the steering wheel.
The air bag/front seat belt
pretensioner system warning light
flashes
if the sensor has a possible
malfunction (page 2-62).
▼ Front Passenger Seat Weight
Sensors
Your vehicle is equipped with a front
passenger seat weight sensors as a part
of the supplemental restraint system.
These sensors are located under both
of the front passenger seat rails. These
sensors determine the total seated
weight on the front passenger seat and
monitor the seat belt buckle for the
front passenger seat. The SAS unit is
designed to prevent the front
passenger front and side air bags and
knee air bags, and seat belt
pretensioner system from deploying if
the front passenger air bag
deactivation indicator light illuminates.
To reduce the chance of injuries
caused by deployment of the front
passenger air bag , the system
deactivates the front passenger front
and side air bags and knee air bags,
and also the seat belt pretensioner
system when the front passenger air
bag deactivation indicator light
illuminates. Refer to the following
table for the front passenger air bag
deactivation indicator light
illumination conditions.

This system shuts off the front
passenger front and side air bags and
knee air bags, and seat belt
pretensioner system, so make sure the
front passenger air bag deactivation
indicator light illuminates according to
the following table.

The air bag/front seat belt
pretensioner system warning light
flashes and the front passenger air bag
deactivation indicator light illuminates
if the sensors have a possible
malfunction. If this happens, the front
passenger front and side air bags and
knee air bags, and seat belt
pretensioner system will not deploy.
Front passenger air bag deactivation
indicator light
This indicator light illuminates to
remind you that the front passenger
front and side air bags and knee air
Essential Safety Equipment
SRS Air Bags
*Some models.2-67
CX-50_8KB8-EA-22A_Edition2_new
2022-1-6 14:55:18