2023 LEXUS RC350 rear view mirror

6
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
Driving position memory buttons*1, 2
Outside rear view mirror switches*1
Door lock switches*1
Power window switches*1
Window lock switch*1
Tire pressure warning reset switch ..................................................................... P.25
*1: Refer to the “OWNER’S MANUAL”.
*2:If equipped
A
B
C
D
E
F

10
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
■Ceiling
Inside rear view mirror*1
Sun visors*1
Vanity mirrors*1
Interior light*1
Personal lights*1
Moon roof switches*1, 2
“SOS” button*2........................................................................................................ P.64
Garage door opener buttons................................................................................ P.60
*1: Refer to the “OWNER’S MANUAL”.
*2:If equipped
A
B
C
D
E
F
G

24
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
BSM main switch
This switch is for both the BSM function
and RCTA function.
Pressing the switch turns the system on
or off. When the switch is turned on,
the indicator on the switch illuminates.
Outside rear view mirror indicators
BSM function:
When a vehicle is detected in a blind
spot of the outside rear view mirrors or
approaching rapidly from behind into a
blind spot, the outside rear view mirror
indicator on the detected side will illu-
minate. If the turn signal lever is oper-
ated toward the detected side, the
outside rear view mirror indicator will
flash.
RCTA function:
When a vehicle approaching from the
right or left at the rear of the vehicle is
detected, both outside rear view mirror
indicators will flash.
Center Display
If a vehicle approaching from the right or left at the rear of the vehicle is detected, the
RCTA icon for the detected side will be displayed on the Center Display.
This illustration shows an example of a vehi cle approaching from both sides of the vehi-
cle.
RCTA buzzer (RCTA function only)
If a vehicle approaching from the right or left at the rear of the vehicle is detected, a
buzzer will sound. The buzzer also sounds for approximately 1 second immediately
after the BSM main switch is op erated to turn the system on.
BSM (Blind Spot Monitor)
The Blind Spot Monitor is a system that has 2 functions:
● The BSM (Blind Spot Monitor) function
Assists the driver in making a decision when changing lanes
● The RCTA (Rear Cross Traffic Alert) function
Assists the driver when backing up
These functions use same sensors.
A
B
C
D

47
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
Left-hand side temperature control switch
Automatic mode switch
Off switch
Fan speed down switch
Fan speed up switch
Air flow mode switch
Right-hand side temperature control switch
DUAL mode switch
A/C switch
Outside/recirculated air mode switch
Rear window defogger and outside rear view mirror defoggers switch
Windshield defogger switch
Automatic Air Conditioning System
Air outlets and fan speed are automatically adjusted according to the temperature set-
ting.
Control panel
A
B
C
D
E
F
G
H
I
J
K
L

61
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
■Programming HomeLink®
Steps 1 through 3 must be performed within 60 seconds, otherwise the indicator light
will stop flashing and programming will not be able to be completed.
1Press and release the HomeLink® button you want to program and check that the
HomeLink
® indicator light flashes (orange).
2Point the remote control transmitter
for the device at the rear view mirror,
1 to 3 in. (25 to 75 mm) from the
HomeLink
® buttons.
Keep the HomeLink
® indicator light in
view while programming.
3Program a device.
 Programming a device other than an entry gate (for U.S.A. owners)
Press and hold the handheld transmitter button until the HomeLink
® indicator light
changes from slowly flashing orange to rapi dly flashing green (rolling code) or continu-
ously lit green (fixed code), then release the button.
 Programming an entry gate (for U.S.A. owners)/Programming a device in the Cana-
dian market
Press and release the remote control transmit ter button at 2 second intervals, repeat-
edly, until the HomeLink
® indicator light changes from slow ly flashing (orange) to rapidly
flashing (green) (rolling code) or co ntinuously lit (green) (fixed code).
4Test the HomeLink® operation by pressing the newly programmed button and observ-
ing the indicator light:
● Indicator light illuminates: Programming of a fixed code device has completed. The
garage door or other device should operate when a HomeLink
® button is pressed
and released.
● Indicator light flashes rapidly: The garage door opener motor or other device is
equipped with a rolling code. To complete programming, firmly press and hold the
HomeLink
® button for 2 second s then release it.

What to do if...
71
RC350 AWD_RC350_RC300 AWD_RC300_QG_(U)
See the “OWNER’S MANUAL”
Turn signal indicatorIntuitive parking assist
indicator (if equipped)
Headlight indicator (U.S.A.)
(Flashes)
Slip indicator
Tail light indicator (Canada)VSC OFF indicator
Headlight high beam indicator
(U.S.A.)
Parking brake indicator
Automatic High Beam
indicator
(Canada)
Parking brake indicator
PCS warning lightBrake hold standby indicator
Cruise control indicatorBrake hold operated indicator
Dynamic radar cruise control
indicatorSecurity indicator
Cruise control “SET” indicatorLow outside temperature
indicator
*2LTA indicatorEco Driving Indicator Light
BSM (Blind Spot Monitor)
outside rear view mirror indi-
cators
(U.S.A.)
“AIR BAG ON/OFF”
indicator
For further information, refer to the “OWNER’S MANUAL”.