2023 KIA SPORTAGE PHEV lights

20†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSPORTAGE HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Lane Keeping Assist (LK A) Video
QR CODE
When engaged, Lane Keeping Assist is not a substitute for safe driving and may not always warn the driver if the vehicle is driven outside of its lane Always drive safely and use caution
For illustrative purposes only Your actual display, but tons and/ or features may var y
Actual Vehicle Set tings steps may var y by model Refer to section 6 in the Owner ’s Manual for more information
REMINDERS:
•
LK A will not issue a warning if the turn signals or hazard lights are activated
•
When the ignition is cycled, LK A will return to the previously set state
Lane Keeping Assist (LKA)†3
Lane Keeping Assist is designed to detect the lane markers on the road with a front view camera on the windshield, and may assist the driver ’s steering to potentially help keep the vehicle in the lane When turned on, the instrument cluster indicator will initially illuminate gray It will remain gray when the vehicle is traveling slower than 40 mph or when the system does not detect the lane markers When the system detects the lane markers and can assist the steering, the Lane Safety icon will illuminate green
If the vehicle begins to move outside of the lane and turn signal is not activated, LK A may provide steering inputs, trying to prevent the vehicle from moving outside its lane If LK A detects that the vehicle continues moving outside of the lane, LK A may give an audible warning and display a Lane Departure Warning on the instrument cluster
When enabled in vehicle settings*, press and hold the Lane Safety button A to turn on or off
LKA User Settings:
To enable LK A , go to User Settings* in the Instrument Cluster LCD or press and hold the LCD Mode button B on the right side of the Steering Wheel, or press the SETUP key/button on the Infotainment System Select the VEHICLE button to enter the Vehicle Settings* Select DRIVER ASSISTANCE then L ANE SAFET Y
•Assist: LK A will automatically assist the driver ’s steering when lane departure is detected to help prevent the vehicle from moving out of its lane
•Warning Only: LK A will warn the driver with an audible warning when lane departure is detected This mode does NOT provide any steering assist
•Off: LK A will turn off The indicator light will turn off on the cluster
When the front-view camera detects the lane traveled in, both lanes are illuminated
When the front-view camera does not detect the lane traveled in the lanes are not illuminated
When the front-view camera detects the vehicle moving outside of the lane being traveled in, a red indicator will illuminate either on the left or right lane (shown in both images above)
The Warning Volume can be adjusted in User Set tings* in the Instrument Cluster or Vehicle Set tings* in the Infotainment System
QUICK TIP
(But tons located on right side of steering wheel)
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
OK
MODE
MODE
OKOK
OKOK
OK
OK
OK
OK OK
OK
OK
A
B
ADAS

30†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSPORTAGE HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Remote Smart Parking Assist (RSPA) Video
Intelligent Speed LimitAssist (ISLA) Video
QR CODE
Remotely moving for ward or backwardHOLDHOLD
Remote Smart Parking Assist (RSPA) uses the vehicle sensors to help park and exit parking spaces remotely from outside the vehicle by automatically searching for parking spaces and then controlling the steering wheel, transmission, and vehicle speed to park the vehicle
To park with Remote Parking (from outside the vehicle), using the Smart Key:
•While in the vehicle, with the vehicle stopped in front of the parking space, vehicle aligned, and the transmission in Park, press and hold the Parking/ View button A
•Select REMOTE on the infotainment system screen When the message UNDER REMOTE CONTROL appears, exit the
vehicle with the Smart Key on hand Ensure all doors are closed
•The emergency lights will blink to when the system is ready to be activated
•Press and hold either the Forward B or Backward C button on the Smart Key, depending on how you want to park, and the vehicle will move in the direction of whichever button you press
Remote Smart Parking Assist (RSPA)*†3
B
C
Refer to section 6 in the Owner ’s Manual for more information
ADAS
AUTO
HOLDEV
HEV
DRIVE MODE
(But ton located below gear shift knob)
Intelligent Speed Limit Assist (ISLA)*†4
Intelligent Speed Limit Assist is designed to use the information from the posted speed limit and the navigation system to inform the driver of the speed limit
When ISL A is on and active, the system will display an alert on the Instrument Cluster LCD of the detected speed limit If the vehicle’s current speed exceeds the detected speed limit, a warning will sound and the vehicle’s current speed will blink on the LCD
ISLA User Settings:
•To enable ISL A on, press the SETUP key/button on the Infotainment System Select the VEHICLE button to enter the Vehicle Settings Select DRIVER ASSISTANCE, SPEED LIMIT, and one of the three modes:
- Speed Limit Assist: Informs the driver of the posted speed limit, displays a message to change the speed to help the driver stay within the posted speed limit
- Speed Limit Warning: Informs the driver of the posted speed limit D and warns the driver when the vehicle is traveling faster than the posted speed limit
- Off: ISL A is disabled
See section 6 in the Owner ’s Manual for more detailed information, limitations and conditions
You can set a speed limit offset to the posted speed limit by going to Vehicle Set tings, Driver Assistance, Speed Limit, then Speed Limit Offset Set the offset to “0” if you want the vehicle to travel at the posted speed limit when ISL A is on
QUICK TIP
REMINDERS:
•
Vehicle must be parked and in a safe location to change the speed set tings
•
Additional information may be displayed if additional road sign information is detected
A
EF
75°F１ 2 .１0 １0 20 30324mi2400miAUTO
HOLD
MPH
CHARGE
ECO
POWER
L H
D

D

34†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSPORTAGE HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
DRIVER'S PANEL
DRIVER’SPANEL
Power Liftgate Open/Close Button*
Open: Press and hold briefly the A button for
approximately one second to open the liftgate
Close: Press and hold the A button until liftgate is
completely closed If the button A is released while closing,
the power liftgate will stop and a warning chime will sound
(But ton located to the left of Steering Wheel)
REMINDER: This control does not adjust brightness on the infotainment system screens Use the display set tings in the Setup menu to adjust the brightness on the screen
Refer to section 5 in the Owner ’s Manual for more information
(But tons located on left of Steering Wheel)
Refer to section 6 in the Owner ’s Manual for more information For illustrative purposes only Your actual display, but tons and/or features may var y
Refer to section 5 in the Owner ’s Manual for more information
REMINDERS:
•
ESC is turned ON by default at vehicle star tup When ignition is cycled, ESC will turn ON again
•
The ESC Indicator Light in the instrument cluster will illuminate whenever the ESC is in operation
The ESC system is designed to help stabilize the vehicle during certain cornering maneuvers It is a good idea to keep the ESC turned ON for daily driving whenever possible
Press and hold the ESC button B turn ESC OFF/ON
Electronic Stability Control (ESC)†5
With parking lights/headlights ON, press switch A (+) or (-) to
adjust the brightness of the instrument panel illumination
Instrument Cluster Illumination Control
Hill-Start Assist Control (HAC)†6
HAC is designed to help prevent the vehicle from rolling backward when accelerating from a stop while on a steep incline HAC provides a 2-second delay before the vehicle may start rolling backward by keeping the brakes momentarily engaged even after you depress the accelerator
The HAC automatically activates during initial acceleration from a stop on an incline whether the ESC is OFF or ON but does NOT activate when the ESC has malfunctioned
REMINDERS:
•
HAC does not operate when the gear shift is in the P (Park) or the N (Neutral) position
•
HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
•
In the event of HAC system malfunction, see an Authorized Kia Dealer for ser vice
HOLD
HOLD
HOLD
HOLD
AB
A
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Liftgate Buttons and Operation Video
QR CODE

38 *IF EQUIPPED
STEERING WHEEL CONTROLS
SPORTAGE HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
STEERING WHEEL CONTROLS
Headlight ON position
Parking light position
AUTOAuto Light* / DRL / HBA
OFFLights OFF
OFFOFFAUTO
AUTO
OFFOFFAUTO
AUTO
Headlights & High BeamsHigh Beam Assist (HBA)
To operate:
•Rotate lever to change the Headlight function
•Push lever to turn High Beams ON
•Pull lever to flash Headlights / High Beams
AUTO Light* — When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically, depending on the amount of light outside the vehicle
High Beam Assist is designed to
automatically adjust the headlight range
by switching between high and low beams
based on light detected from other vehicles
and road conditions
To enable HBA , toggle the light switch to
the AUTO Light position and turn on the
high beams by pushing the lever away from
you The High Beam Assist indicator will
illuminate
REMINDERS:
•
HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously
•
If the light switch is switched to the headlight position, HBA will turn off and the low beams will be on continuously
Refer to section 5 in the Owner ’s Manual for more information
Daytime Running Lights (DRL)
DRL may help others to see the front of your vehicle during the day The lights will be on automatically when the ignition or Engine Start/Stop button is ON and the headlight switch is in the AUTO position, unless one of the following occurs:
•Headlights are on
•Parking brake is applied
•Fog lights are on
•Engine is turned off
•Switch is in the OFF position
REMINDER: DRL only operates during the day time
Refer to section 5 in the Owner ’s Manual for more information
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
High Beam Assist (HBA) Video
Steering Wheel Controls Video
QR CODE

39 *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLSOFFOFFAUTO
AUTO
OFFOFFAUTO
AUTO
Windshield Wipers & Washers
Front Wiper & Washer
To operate front wipers and washers:
•Move lever Up/Down to change Wiper modes
•Press INT switch B up/down to adjust Intermittent Wipe Speed
•Pull lever to spray and wipe
Rear Wiper & Washer
To operate rear wipers and washers:
•Rotate Rear Wiper switch to change Wiper modes
•Push lever to spray and wipe
MIST
OFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
MIST: Single wipe
OFF: Wiper off
I N T: Intermittent Wipe
LO: Slow Wiper Speed
HI: High Wiper Speed
HI: Continuous wipe
LO: Slow wipe
OFF: Wiper off
Turn Signals & Fog Lights*
One-Touch Lane Change Signal is activated by briefly pressing the Turn Signal Lever up/down slightly for less than 1 second and then releasing The lane change signal will blink 3 times
To change how many times (3/5/7) the Lane Change Signal blinks, go to the User Settings Mode in the LCD Instrument Cluster and select Lights, then One-Touch Turn Signal
For illustrative purposes only Your actual display, but tons and/or features may var y
For more information on the User Settings Mode, please refer to section 5 in the Owner ’s Manual
Refer to section 5 in the Owner ’s Manual for more information
One-Touch Lane Change
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Wipers and Wiper Stalk Video
Lifting Wipers / Wiper Service Mode Video
QR CODE
A
BREMINDER: Headlights must be ON for fog light operation
LO and HI sets wiper speed No intermit tent wipe function is available on rear wipers
QUICK TIP
• Moving switch B to HI increases intermit tent wipe frequency and wipe speed Moving switch B to LO decreases frequency of wipes
•
Set the wiper to OFF position when the wiper is not in use
QUICK TIPS
To operate:
•Turn Signals - Move lever Up/Down for Right/Left Turn Signal
•Slightly move lever up/down to activate One-Touch Lane Change Signal
•Fog Lights - Press switch A up/down to turn Fog Lights ON/OFF

64†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPED
OTHER KEY FEATURES
SPORTAGE HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
OTHER KEYFEATURES
ABC
HomeLink® with Auto-Dimming Rearview Mirror*†2
The HomeLink® Universal Transceiver is designed to connect to your garage door opener, electric gate, home lighting, etc The Auto-Dimming Rearview Mirror is designed to help reduce glare coming from a vehicle’s headlights in the rear HomeLink® with Auto-Dimming Rearview Mirror can connect to three electronic transmitters
REMINDER: Mirror indicator light will illuminate when automatic dimming is ON
Programming a New HomeLink® Button:
1 Press and release the HomeLink® Channel button A, B or C, you would like to program The HomeLink® User Inter face Indicator G will flash orange slowly (If it doesn’t, go to the steps of “Erasing HomeLink® Buttons” section on next page, and start over)
2 Position the garage-door opener remote 1-3 inches away from the HomeLink® buttons
3 While the HomeLink® User Inter face Indicator G is flashing orange, press and hold the garage-door opener remote button until the HomeLink® User Inter face Indicator G changes from orange to green
4 Wait until your garage door comes to a complete stop, regardless of position, before proceeding to the next step
5 Press and release the HomeLink® Channel button A, B or C that you’re programming If the HomeLink® User Interface Indicator G is solid green, HomeLink® is connected and should operate when the HomeLink® Channel button A, B or C is pressed If your device operates, programming is complete
–If the indicator light rapidly flashes green, firmly press, and hold the HomeLink® Channel button A, B or C slowly, for two seconds up to three times in a row, to complete the programming process Do not press the HomeLink® Channel button rapidly If your device now operates, programming is complete
–If the device does not operate, continue with step 6
6 At the garage door opener motor, (security gate motor, etc ) locate the “Learn”, “Smart ”, “Set ” or “Program” button This can usually be found where the hanging antenna wire is attached to the motor-head unit (see the device’s manual to identify this button) The name and color of the button may vary by
manufacturer A ladder and/or second person may simplify the following steps
7 Firmly press and release the “Learn”, “Smart ”, “Set ” or “Program” button You now have up to 30 seconds to complete the next step
8 Return to the vehicle and firmly press and hold the HomeLink® button slowly, for two seconds, up to three
times in a row Do not press the HomeLink® button rapidly As soon as you see the garage door start to move, stop pressing any buttons until a few seconds after the garage door has come to a complete stop, regardless of position At this point programming is complete and your device should operate when the HomeLink® Channel button is pressed
A HomeLink® button
B HomeLink® button
C HomeLink® button
D Garage Door Opener Status Indicator:
Closing or Closed
E HomeLink Operation Indicator
F Garage Door Opener Status Indicator:
Opening or Opened
G HomeLink User Inter face Indicator
EDF(RearviewMirror)
G
For illustrative purposes only Your actual display, but tons and/or features may var y

67†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
OTHER KEY FEATURES
When the Smart Key fob is on your person and you are near the back of the vehicle, within close proximity, the hazard lights will blink and a chime will sound for about 3 seconds as an alert that the Smart Power Liftgate is about to open Then the alert system will blink and chime two additional times before opening the Smart Power Liftgate
The Smart Power Liftgate feature is off by default To enable the Smart Power Liftgate, go to Vehicle Settings* in the Infotainment System Press the SETUP key or onscreen button, then VEHICLE Select DOOR, then SMART LIFTGATE
Manual Liftgate* / Liftgate
Release Button
Smart Power Liftgate*†1 0
Located underneath the rear liftgate hatch With liftgate unlocked, press the Liftgate Release Button A and pull the liftgate up by the handle to open
Refer to section 5 in the Owner ’s Manual for more information
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Smart Liftgate Operation, Opening Height/Speed Adjustment Video
Liftgate Buttons and Operation Video
Manual Liftgate & Key Fob Controls Video
QR CODE
A
REMINDERS:
•
All doors are closed and locked after about 15 seconds for the system to operate
•The Smar t Power Liftgate feature will not operate when:
-
The doors are recently closed and locked, and the Smar t Key is still detected after 15 seconds near the vehicle or within 60 inches of the door handles
-A door is not locked or closed
-The Smar t Key is in the vehicle
•
Press any but ton on the Smar t Key fob during the Detect and Aler t stage to deactivate the Smar t Power Liftgate function
•Ensure obstacles and people are out of the way of the liftgate
•During the Smar t Power Liftgate aler t, the Smar t Power Liftgate can be deactivated with the Smar t Key by pressing any but ton on the key fob
•
The open height can be adjusted For information on how to set open height, see your Owner ’s Manual
QUICK TIPS
•
The liftgate must be unlocked before it can be opened by the Liftgate Release But ton
•
The liftgate unlocks automatically and can then be opened, when the Smar t Key fob* is within close proximit y to the vehicle
QUICK TIPS
OTHER KEYFEATURES

68 *IF EQUIPPED
OTHER KEY FEATURES
SPORTAGE HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
OTHER KEYFEATURES
Panoramic Sunroof Operation
with Power Sunshade*
The sunroof operation is controlled through a multidirectional switch The ignition or Engine Start/ Stop button* needs to be in the ON position to operate the sunroof
To slide the power sunshade and sunroof:
• Auto Open: Slide the switch D backward to the farthest position and release
• Auto Close: Slide the switch D forward to the farthest position and release
To slide the power sunshade only:
• Auto Open: Slide the switch D partially backward to the first detent position and release
• Auto Close: Slide the switch D partially forward to the first detent position and release
To slide the sunroof (with power sunshade open):
• Open: Slide the switch D backward to the first detent position and release
• Close: Slide the switch D forward to the first detent position and release to close sunroof glass only Slide the lever backward to the farthest position and release to close sunroof glass and sunshade
To tilt the sunroof:
• Raise: Push switch D upward
• Lower: Pull switch D downward
OFFPASSENGER
AIR BAG
(Type B; panel located overhead center of the front row)Refer to section 5 in the Owner ’s Manual for more information
Refer to section 5 in the Owner ’s Manual for more information
Map/Room Lamps
Automatic turn off function*
The interior lights automatically turn off approximately 30 seconds after the ignition or Engine Start/Stop button* is OFF
Map/Room Lamp Operation
•Press lens A to turn the Driver ’s/Passenger ’s Map Lamps ON/OFF This light produces a spot beam for convenient use as a map lamp or as a personal lamp for the driver or the front passenger
•Press button B to turn all the Map/Room Lamps ON/OFF
•
Press button C to turn the Map/Room Lamp ON, for 30 seconds, when a door is opened, unlocked from Smart Key or the ignition is turned OFF
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Sunroof Operation Video
QR CODE
AABC
D
REMINDERS: •
If the ignition is turned off with the Sunroof not fully closed, the Instrument Cluster LCD will display a warning message and a chime will sound for a few seconds •
Power sunshade needs to remain OPEN while sunroof is open •
Power sunshade cannot slide when the sunroof is in the tilt position or tilt while in an open or slide position •
Do not adjust the power sunroof or sunshade while driving This could result in loss of control of the vehicle •
When closing, be mindful of any objects or persons
• When doors are unlocked by the Smar t Key, the lamp turns ON for approximately 30 seconds
•
If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 3 seconds after the system is in armed stage
•
Using interior lights for an extended period of time may cause bat ter y discharge
QUICK TIPS
To stop the sunroof/sunshade at any position, push or pull the sunroof control switch in any direction
QUICK TIP