†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 23
MODE
MODE
MODE
MODE
MODE
MODE MODE
MODE
MODE
OKOK
OK
OK
OK
OK
OK
OK
Drive mode (Return button)Cruise Control
Bluetooth Eco L FA
User Settings
HDA
Audio LV DA MSLA - ISLA
MODE
Smart Cruise Control
OK
ROA
MODE
HDA
OK
OK
Rear Cross-traffic Collision-Avoidance Assist (RCCA)†3
Rear Cross-traffic Collision-Avoidance Assist is designed to detect vehicles approaching from the left and right side while your vehicle is reversing, and warning the driver that a collision is imminent with a warning message and an audible warning. Also, to help prevent collision braking assist is applied.
When the rear-corner radar sensors detect approaching vehicles from the rear left or rear right side of the vehicle A, RCCA will sound a warning, the warning indicators on the outside rearview mirror will illuminate and a message will appear on the Instrument Cluster LCD B and the audio head unit.* If RCCA detects that the collision risk has increased, RCCA automatically applies the brakes to reduce your speed, potentially helping to minimize the effects of a possible collision.
RCCA is designed to operate under the following conditions:
•When the gear shift is in Reverse
•When the vehicle is moving slower than 5 mph
RCCA Settings:
•RCCA can be turned on/off by going to the User Settings* in the Instrument Cluster or the Vehicle Settings* in the Infotainment System
•Only adjust settings when the vehicle is at a standstill, gear shift is in Park and the ignition is ON or the Engine Start/Stop button* in the ON position
•To access User settings* in the Instrument Cluster - Press the Mode button C on the Steering Wheel to toggle to User Settings . Press the OK button D up/down to toggle to Driver Assistance, then Parking Safety. Select Rear Cross Traffic Safety and press the OK button D
•To access Vehicle settings* in the Infotainment System – Press the SETUP key or the onscreen SETUP button. Press VEHICLE to enter Vehicle Settings. Select Driver Assistance, then Parking Safety and select Rear Cross Traffic Safety
•Warning Timing – When in the Driver Assistance menu, select Warning Timing and one of the following:
- Normal: Maximizes the amount of distance between the vehicles before the initial warning occurs
- Later: Reduces the amount of distance between the vehicles before the initial warning occurs
REMINDERS:
•
When vehicle power is cycled, RCCA will remain in the previous state
•
When a vehicle is approaching within the sensing range, and traveling faster than 3 mph, the RCCA system will show a warning
W h e n engaged, RCCA is a supplemental system. Do not solely rely on this system and always pay at tention to the road and its conditions
Refer to section 5 in the Owner ’s Manual for more information.
116mi
R5643mi80 °F
(But tons located on right side of steering wheel)
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Rear Cross-traffic Collision-Avoidance Assist (RCCA) Video
QR CODE
A
B
C
D
Warning Volume can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings on the audio head unit. Go to Driver Assistance, then Warning Volume.
QUICK TIP
ADVANCED DRIVER ASSISTANCE SYSTEM (ADAS)
ADAS
28CARNIVAL FEATURES & FUNCTIONS GUIDE
STEERING WHEEL CONTROLS
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Tilt/Telescoping/Heated Steering Wheel Video
High Beam Assist (HBA) Video
QR CODE
HOLD
HOLDPOWER
DOOR OFFHOLD
OFFOFF
AUTO
OFFOFF
AUTO
Headlight position
Parking light position
AUTOAuto Light / HBA / DRL
OFFOFF position
Tilt/Telescoping Steering Wheel†1 9
To adjust the Steering Wheel, press the Lock-Release Lever A down and adjust B to the desired angle and C to the desired distance.
When finished, pull the Lock-Release Lever A up to lock the Steering Wheel in place.
Headlights & High Beams
To operate:
•Rotate the switch to change the Headlight function
•Push the lever to turn High Beams ON
•Pull the lever to flash Headlights / High Beams
High Beam Assist (HBA)
The High Beam Assist is designed to automatically adjust the head-light range by switching between high and low beams based on light detected from oncoming vehicles and road conditions.
To enable HBA , toggle the light switch to the AUTO Light position and turn on the high beams by pushing the lever away from you. The High Beam Assist indicator will illuminate.
AUTO Light function – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically depending on the amount of light outside the vehicle.
Daytime Running Lights (DRL) - DRL may help others to see the front of your vehicle during the day. The lights will turn on automatically when the ignition or Engine Start/Stop button is ON and the headlight switch is in the AUTO position, unless one of the following occurs:
•Headlights are on
•Parking brake is applied
•Engine is turned off
•Headlight switch is in the OFF position
REMINDERS:
•HBA will operate when vehicle speed exceeds 25 mph •
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously. If the lever is pulled toward you while HBA is operational, HBA will turn off •
If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
Refer to section 4 in the Owner ’s Manual for more information.
Do not adjust the steering wheel while driving as this may cause you to lose control of the vehicle.
High Beam Assist does not operate below cer tain speeds, or in some lighting and driving conditions. Please be aware of your surroundings and exercise proper road etiquet te when operating a vehicle using the high beams
Refer to section 4 in the Owner ’s Manual for more information.
A
B
C
It may be helpful to pull/push the bot tom of the Steering Wheel towards/away from you to adjust the desired distance prior to adjusting the angle.
QUICK TIP
†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPED
STEERING WHEEL CONTROLS
*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 29
MIST: Single wipeOFF: Wiper offI N T: Intermittent wipeLO: Slow wipeHI: Fast wipe
MISTOFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
HI: Fast wipeLO: Slow wipeOFF: Wiper off
OFFOFF
AUTO
OFFOFF
AUTO
* M M V T U S B U J P O T B S F G P S E F N P O T U S B U J P O Q V S Q P T F T P O M Z " D U V B M G F B U V S F T P O W F I J D M F N B Z W B S Z
3 F G F S U P T F D U J P O J O U I F 0 X O F S s T . B O V B M G P S N P S F J O G P S N B U J P O
Windshield Wipers & Washers
To operate:
•Move lever Up/Down to change wiper modes
•Press button B Up/Down to adjust Intermittent Wipe Speed
•Pull lever to spray and wipe
Rear Wiper & Washer
To operate:
•Rotate Rear Wiper switch to change Wiper modes
•Push to spray and wipe
Turn Signals & Fog Lights*
To operate:
•Turn Signals - Move lever Up/Down for Right/Left Turn Signal
•Fog Lights - Press switch A up/down to turn Fog Lights ON/OFF
REMINDER: Headlights must be ON for Fog Light operation.
The One-Touch Lane Change Signal is activated by briefly pressing the Turn Signal Lever slightly for less than 1 second and then releasing. The lane change signal will blink 3 times.
To change how many times (3/5/7) the Lane Change Signal blinks, go to the User
Settings Mode in the LCD Instrument Cluster modes.
STEERING WHEEL CONTROLS
•Pressing but ton B up increases Intermittent wipe frequency and wipe speed. Pressing the but ton down decreases the frequency of wipes
•Set the wiper to the OFF position when the wiper is not in use
QUICK TIPS
LO and HI sets the wiper speed. There is no intermit tent wipe function on the Rear Wipers
QUICK TIP
AB
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Wipers and Wiper Stalk Video
Lifting Wipers / Wiper Service Mode Video
QR CODE
Lifting Wipers (Wiper Service Mode)
To lift the windshield wipers to clean windshield, inspect or replace wiper blades or raise wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the service position C to prevent damaging the hood.
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch (above) to the MIST position and hold the switch for more than two seconds until the wiper blade is in the fully up position.
To return wipers to normal position, turn the ignition ON, then activate MIST.
Refer to section 7 in the Owner ’s Manual for more information.
Refer to section 4 in the Owner ’s Manual for more information.
C
STEERING WHEEL CONTROLS
†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPED30CARNIVAL FEATURES & FUNCTIONS GUIDE
Pairing a Phone
For instructions on how to pair a phone, refer to the audio system’s user ’s guide or your vehicle’s Quick Start Guide.
How to Place a Call
Below are methods for placing a call using the Steering Wheel controls:
When using the voice command feature,* waiting for the system BEEP before speaking the command.
•Option 1: Press the Talk button* A. Then say the command “Call {name}” or “Dial {number}” followed by contact name or number
•Option 2: Press the Call button C (displays the phone screen with call history)
For more information, refer to the Car Infotainment System Quick Reference Guide.
Your vehicle’s steering wheel but tons may differ from those in the illustrations. See your Owner ’s Manual for more details.
Driving while distracted is dangerous and should be avoided. Drivers should remain at tentive to driving and always exercise caution when using the steering-wheel-mounted controls while driving.
For more information, if equipped, refer to the Car Infotainment System Quick Reference Guide. For Bluetooth® Wireless Technology FAQs, go to w w w.kia.com, Owners section, or call Consumer Information for Bluetooth® Technology at (800) 333-4KIA .
Bluetooth® Wireless Technology†2 , 1 7
A Talk button: Press to activate voice recognition/bring up menus/place calls with minimal voice command prompts from the system. Press and hold to exit voice recognition
Kia Connect with Navigation* – When enrolled with a Kia Connect subscription, press this button to activate the Kia Connect Voice Assist to use navigation guidance and search destinations
B Volume button: Press up/down to raise/lower the speaker volume Mute button: Press to mute the microphone during a call and to mute the audio system speakers, or to pause Bluetooth® streaming media
C Receive/Place Call button: Press to receive/place/transfer calls. If no phone is paired, press the button to pair a phone
D Custom button: Press to access programmed feature. Press and hold the button to program it to one of several features
INFOTAINMENT SYSTEM
MODE
MODE
MODE
MODE
MODE
MODE MODE
MODE
MODE
OKOK
OK
OK
OK
OK
OK
OK
Drive mode (Return button) Cruise Control
Bluetooth Eco L FA
User Settings
HDA
Audio LV DA MSLA - ISLA
MODE
Smart Cruise Control
OK
ROA
MODE
HDA
OK
OK #
$ %
"
•When using the voice command feature, wait for the system BEEP before speaking the command
•
Phone book transfer upload time varies by phone model and with the number of phone book entries
•Because of differences in phone qualit y, ser vice providers and Bluetooth® Wireless Technology chip programming, functionalit y may differ from one phone to another
•The system can register or pair multiple Bluetooth® devices. See the Car Infotainment System Quick Reference Guide for more information on setup and limitations
QUICK TIPS
During the pairing process, be sure to accept the connection requests on the phone for phone book download and to allow acceptance of all future Bluetooth® connection requests
QUICK TIP
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Star, Favorite & Radio Presets Buttons Video
QR CODE
INFOTAINMENTSYSTEM
MODE
MODE
MODE
MODE
MODE
MODE MODE
MODE
MODE
OKOK
OK
OK
OK
OK
OK
OK
Drive mode (Return button)Cruise Control
Bluetooth Eco L FA
User Settings
HDA
Audio LV DA MSLA - ISLA
MODE
Smart Cruise Control
OK
ROA
MODE
HDA
OK
OK
BC
†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 31
Bluetooth® Wireless Technology*†2 , 1 7 (continued)
Voice Recognition* and Phone Contact Tips
The system may have difficulty understanding some accents or uncommon names. Improve the per formance by making a few simple changes to your phone contacts, listed below. To help optimize the Bluetooth Wireless Technology Voice Recognition system, see other tips and reminders under Quick Tips.
•Use full names (first and last names) vs. short or single-syllable names (“John Smith” vs. “Dad,” “Smith Residence” vs. “Home”)
•Avoid using special characters, emojis or hyphenated names (@, &, #, /, -, *, +, etc.)
•Avoid using acronyms (“In Case of Emergency” vs. “ICE”) or words with all capital letters
•Spell words completely, no abbreviations (“Doctor Smith” vs. “Dr. Smith”)
Audio Controls†1 7
A Audio MODE button: Press to cycle through the FM/AM/SiriusXM®*†2 0
Media Modes; Audio System ON: Press to turn the power on
B Seek/Track button: FM/AM/SiriusXM®* Modes: Press up/down to advance through Preset
Stations. Press and hold to auto seek
Media Modes: Press up/down to move the track up/down. Press and hold to fast forward/
rewind (except for Bluetooth® Audio)
C Volume button: Press up/down to raise/lower the volume
Mute button: Press to mute all audio (in some Media Modes the media pauses when pressed)
Driving while distracted is dangerous and should be avoided. Drivers should remain at tentive to driving and always exercise caution when using the steering-wheel-mounted controls while driving. For fur ther audio system operation, refer to pages 30-36.
Your vehicle’s steering wheel but tons may differ from those in the illustrations.
Refer to section 4 in the Owner ’s Manual for more information.
INFOTAINMENT SYSTEM
•
Bluetooth® Music Streaming – If the Bluetooth® music is inaudible or too low, you may need to turn up the volume on the connected phone
•
When placing a call, speak in a natural, moderate tone, with clear pronunciation. The system may have trouble recognizing commands if you speak too softly or too loudly
•Always wait for the beep before speaking any commands
•
Close windows and sunroof and turn off A /C . Open windows, sunroof, weather (wind/rain), or an A /C fan operating at higher speeds can inter fere with Voice Recognition
•Press the talk but ton and say “Help” to get a list of available commands
QUICK TIPS
•MODE but ton Initial set ting is in radio mode
•In the SETUP menu on the audio head unit screen, select which Media Modes to include in the MODE but ton menu rotation. Press and hold the MODE but ton to enter this set ting menu
QUICK TIPS
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Voice Recognition Tips Video
Steering Wheel Controls Video
QR CODE
A
INFOTAINMENTSYSTEM
†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPED36CARNIVAL FEATURES & FUNCTIONS GUIDE
To adjust the sound settings from any audio mode: Press the SETUP button on the Audio Head Unit, then the onscreen SOUND button. Select the menu item to change settings, then use the onscreen buttons to adjust settings.
Presets: To Save a Preset, press and hold the desired slot. This saves the current station in the selected slot.
SiriusXM® Smart Favorites: In Radio mode, choose SiriusXM®, then select any of the first six favorites. During song or program play, tap the Skip Backward icon to start from the beginning of the song or program. Tap the Play Live icon to return to the live broadcast.
Custom Key H To program a custom key, press and hold the Custom Key, then select one of the available features you would like the Custom Key to open.
Software updates - To keep your software up to date, Kia provided over-the-air updates, free of charge. You can also snap the QR code to watch the video, or visit the official Kia update webpage at https://update.kia.com. Note, visiting a dealer for software update may include an additional charge.
Kia Connect†1 with Navigation*†8 – F M /A M /S ir i us X M®†1 5/Media (USB, Aux, Bluetooth® A u d i o )
Your vehicle’s audio system may differ from that in the illustration.
For fur ther Kia Connect with Navigation operations, refer to the Car Infotainment System Quick Reference Guide.
Kia Connect is currently unavailable for model year 2022 and later vehicles sold or purchased in Massachuset ts. See Kia Connect Terms of Ser vice at owners.kia.com for more information.
REMINDERS:
•
To help minimize driver distraction, some audio system functionalities have been modified while the vehicle is in Drive, Reverse or moved out of Park
•
Prolonged use of the audio head unit in ACC mode may drain the vehicle’s bat ter y
Press briefly to do the following:• FM/AM mode: Play the previous/next frequency• SiriusXM® mode: Change the channel• MEDIA mode: Change the track, file or title (except for AUX)Press and hold to do the following (over 0.8 seconds):• FM/AM mode: Move quickly through all of the frequencies. When released, the system seeks the next available frequency• MEDIA mode: Rewinds or fast for wards the track or file (except for AUX and Bluetooth® Audio)
A programmable key to provide quick access to one of several available system features
Press to display SETUP/Set tings mode Press to Power ON/OFF. Rotate to adjust Volume
Press to select FM/AM/SiriusXM® modesPress to enter MEDIA mode
Press to display the Map screen for the current position/ Voice mode
Press to display the Navigation menu screen
Rotate to change Radio/SiriusXM® Station/Media tracks/files. Press to select
POWERPUSHVOL
MAPENGINESTART
STOPN AV RADIO MEDIA SETUP
SEEK
TRACK
ENTER
TUNE
FILE
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Kia Connect with Navigation Video
Navigation System Important Tips Video
Navigation System Updates Video
QR CODE
•Volume level bet ween different audio modes:
-
When switching bet ween audio modes (AM, FM, Bluetooth® Audio, etc.), the audio system saves the previous volume level you were listening to. For example, if you were listening to FM radio at volume level 20 then switched to Bluetooth® Audio and adjusted the volume level to 30, the volume level will be at 20 when you switch back to FM radio
•When connected to Android Auto™ or Apple CarPlay® on your smar t-phone, the smar tphone’s navigation system may also be available
•This system suppor ts Android Auto™ and Apple CarPlay® (USB connection only)
•A warning screen may appear periodically to remind users that the navigation system should be operated when the engine is running to prevent bat ter y discharge
•At any time, you can interrupt Kia Connect Command Feedback by pressing the TALK but ton on the steering wheel
QUICK TIPS
INFOTAINMENT SYSTEM
For other audio system information, see pages 30-35.
INFOTAINMENTSYSTEM
44CARNIVAL FEATURES & FUNCTIONS GUIDE
(But ton located below Gear Shift)
Heated Steering Wheel*
Press the Heated Steering Wheel button A to turn the Steering Wheel Heater on/off while the ENGINE START/STOP button is in the ON position. The Steering Wheel Heater will turn off automatically in 30 minutes, or when the button is pressed again to deactivate.
REMINDER: If the steering wheel becomes too warm, turn the system off. The heated steering wheel may cause burns even at low temperatures, especially if used for long periods of time.
Refer to section 4 in the Owner ’s Manual for more information.
REMINDER: Use extreme caution when using the seat warmers to avoid burns. Refer to the Owner ’s Manual for more information.
Seat Warmers / Ventilated Seats*†1 4
Seat Warmers button B: Press the button once for high setting (3 LEDs lit). Press the button twice for medium setting (2 LEDs lit). Press the button a third time for low setting (1 LED lit) and again to turn OFF. Hold the button to turn off Seat Warmer.
These illustrations are for demonstration purposes only. Actual features on vehicle may var y.
Refer to section 4 in the Owner ’s Manual for more information.
Seat Warmers / Ventilated Seats* button C: Press top/bottom of the button once for high setting (3 LEDs lit). Press the button twice for medium setting (2 LEDs lit). Press a third time for low setting (1 LED lit) and again to turn OFF. Hold the button to turn off the Seat Warmers / Ventilated Seats.
CENTER PANEL
A
•If the ignition is turned OFF and then ON again within 30 minutes of the Steering Wheel Heater being turned ON, the system will remain in the ON position
•The system does NOT turn off when the ignition is cycled. To turn off the system, press the Heated Steering Wheel but ton
QUICK TIPS
•With the Seat Warmer switch in the ON position, the heating system in the seat turns OFF or ON automatically depending on the seat temperature
•System is OFF by default. To turn the system ON, press the but ton to turn ON
QUICK TIPS
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Seat Warmers and Ventilated Seats Video
QR CODE
(But tons located below Gear Shift) (Type A shown)
Warming (Yellow LED)
BB
(But tons located below Gear Shift) (Type A shown)
Warming (Yellow LED)
Ventilating (Blue LED)
CC
†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPED
CENTERPANEL
†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 51
MODE
MODE
MODE
MODE
MODE
MODE MODE
MODE
MODE
OKOK
OK
OK
OK
OK
OK
OK
Drive mode (Return button)Cruise Control
Bluetooth Eco L FA
User Settings
HDA
Audio LV DA MSLA - ISLA
MODE
Smart Cruise Control
OK
ROA
MODE
HDA
OK
OK
3 F B S 0 D D V Q B O U " M F S U 3 0 "
X J U I 6 M U S B T P O J D 4 F O T P S T†9
Rear Occupant Alert (ROA) with Ultrasonic Sensors can help alert the driver when rear passengers are left in the rear seats using the ultrasonic sensors and door monitoring. The system is designed to provide three separate alerts:
•The first alert is a message on the Instrument Cluster, “Check Rear Seats” A, and a chime will sound
After the first alert, when the doors are locked and there is movement detected in the rear seats, the horn will sound for about 25 seconds. This alert may activate up to eight times within 24 hours if movement is still detected and system has not been disabled
•
If you have installed the Kia Access app on your smartphone, logged in and activated the Rear Occupant Alert notification, a third alert (notification) will be sent to your phone
To turn the system on or off, in the Instrument Cluster, go to User Settings, select Convenience, and
then Rear Occupant Alert.
Rear Occupant with Ultrasonic Sensors activates under the following conditions:
•A rear passenger door is opened and closed
•The ignition has been turned off
•The driver ’s door has been opened, then closed
•The doors are locked with the Smart Key or the door lock button on the door handle
This system is not a substitute for one’s at tention and may not detect all movement within the vehicle. Always check the vehicle’s interior before exiting.
Check rear seats
: Alarm OffOK
* N B H F T B S F G P S J M M V T U S B U J W F Q V S Q P T F T P O M Z B O E N B Z O P U S F7U F D U B D U V B M G F B U V S F P S P Q F S B U J P O
B
A
REMINDERS:
•
To avoid false aler ts, make sure the vehicle’s windows are rolled up
•
If objects such as boxes are stacked in front of the ultrasonic sensors, the system may not detect any movement
•
The ultrasonic sensors may occasionally detect movement in the vehicle and cause false aler ts when there are no rear occupants present. False aler ts can occur due to:
-The presence of insects near the system sensor
-Rushing air from a window that is rolled down
-Movement around the exterior of the vehicle
-Surrounding noise or vibration
-Vehicle passing through a car wash
-Movement in the driver or front passenger seat being detected
•
The Rear Occupant Aler t with Ultrasonic Sensors system may fail to detect movement and activate an alarm if:
-Movement is subtle or does not continue
-A small child sits directly in a seat without a car seat
-
A rear passenger is covered with an object such as a blanket, obstructing the sensor ’s view
•
The first aler t message will not display on Instrument Cluster if the rear doors are never opened. Either rear door must be opened after unlocking the vehicle before the system will activate
•
To temporarily disable aler ts, press the OK but ton B on the Steering Wheel while the message is displayed
•
To turn the aler t off while sounding, press the unlock but ton on the Smar t Key or press the door lock but ton on the door handle
•
Must be enrolled in Kia Connect and Kia Access app installed on the phone to receive ROA aler t notifications on your smar tphone
QUICK TIPS
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Rear Occupant Alert (ROA) with Ultrasonic Sensors Video
QR CODE
See section 4 in the Owner ’s Manual for more information.
OTHER KEY FEATURES
OTHER KEY FEATURES