Page 292 of 344

290SERVICING AND MAINTENANCE  
Interior Fuses
The interior fuse panel is located in the passenger compartment on the left side dash panel under the instrument panel.
CavityBlade Fuse Description
*If Equipped
F31 7.5 Amp Brown Occupant Restraint Controller
F33 20 Amp Yellow Window Motor Passenger
F34 20 Amp Yellow Window Motor Driver
F36 20 Amp YellowIntrusion Module/Siren, Radio, UCI/USB Port, VSU, Climate Control, 
Electronic Steering Lock, Power Folding Mirrors, Security Gateway/DTV
F37 10 Amp RedInstrument Panel Cluster, Drivetrain Control Module, Adaptive Cruise, 
ECC (HVAC) Blower
F38 20 Amp Yellow Door Lock/Unlock, Liftgate Release
F42 7.5 Amp Brown Brake System Module, Electric Power Steering
F43 20 Amp Yellow Washer Pump Front And Rear
F47 20 Amp Yellow Rear Left Window Lifter
F48 20 Amp Yellow Rear Right Window Lifter
F49 7.5 Amp BrownPark Assist, Blind Spot, Voltage Stabilizer, Humidity Sensor, Electronic Steering Lock, 
Temp Sense, Mirror, Heated Seats, Light And Rain Sensor, Start Stop Switch
F50 7.5 Amp Brown Occupant Restraint Controller
F51 7.5 Amp BrownElectronic Climate Control, Occupant Classification, Rear View Camera, Climate Control, 
Headlamp Leveling, Terrain Select, Heated Rear Window, Trailer Tow, Haptic Lane Mod
F53 7.5 Amp Brown Keyless Ignition Node Module, Electric Park Brake, RF Hub, Cluster
F94 15 Amp Blue Lumbar Adjust Driver Seat, Power Outlets
22_MP_OM_EN_USC_t.book  Page 290   
         
        
        
     
        
        Page 293 of 344
SERVICING AND MAINTENANCE291
BULB REPLACEMENT 
Replacement Bulbs, Names, And Part Numbers
In the instance a bulb needs to be replaced, this section includes bulb description and replacement part numbers.
NOTE:See an authorized dealer for LED bulb replacement.
Interior Bulbs
Lamps Bulb Number
Front Courtesy Light C5W
Front Courtesy Lights (Sun Visors) C5W
Rear Dome Light (Models Without Retractable roof) C5W
Rear Interior Lights (Models With Retractable roof) C5W
Interior Lights HT-168
Dome Light (Glove Box) HT-168
8
22_MP_OM_EN_USC_t.book  Page 291   
         
        
        
     
        
        Page 294 of 344
292SERVICING AND MAINTENANCE  
Exterior Bulbs
Lamps Bulb Number
Low Beam Headlamps LED (Serviced at an authorized dealer)
High Beam Headlamps LED (Serviced at an authorized dealer)
Front Position/Daytime Running Lights (DRL)/Front Directional - Premium LED (Serviced at an authorized dealer)
Front Direction Indicator & Position Lamps - Base 7442NA
Side Marker Lamp Base:2825
Front Fog Lamps Base: H11LL/ Premium LED
Side Indicators (Side View Mirror) LED (Serviced at an authorized dealer)
Tail/Brake Lights Premium Tail Lights: LED (Serviced at an authorized dealer)
Base Tail Lights: W21/5WLL
Turn Indicators W21WLL For Premium Tail Lamps
W21/5WLL For Base Tail Lamps
Center High Mounted Stop Lamp (CHMSL) LED (Serviced at an authorized dealer)
License Plate Lamp LED (Serviced at an authorized dealer)
Liftgate Lamp Reverse W21WLL
Liftgate Lamp Tail LED (Serviced at an authorized dealer)
22_MP_OM_EN_USC_t.book  Page 292   
         
        
        
     
        
        Page 295 of 344

SERVICING AND MAINTENANCE293
Replacing Exterior Bulbs
Turn Signal Light/Position Lights (Base)
To replace the bulbs proceed as follows:
1. Open hood.
2. Reach behind headlamp near the radiator.
3. Remove the electrical connectors.
4. For the turn signal bulb, rotate in a counter -
clockwise direction and remove the bulb and 
bulb socket. Pull the bulb axially to remove it 
from the socket.
5. Install the bulb and sockets and rotate them  clockwise making sure that it is properly 
locked.
6. Reconnect the electrical connectors.
7. Close hood.
NOTE:It is advised referring to an authorized dealer. Front Fog Lights (Base)
To replace the bulbs proceed as follows:
1. Turn the front wheels completely.
2. Remove the wheel liner.
3. By pushing the electrical connector tab 
remove the electrical connector.
4. Rotate the bulb counterclockwise, and then  replace the bulb.
Fog Lamp Housing
5. Insert the new bulb in the socket, making sure  the bulb is locked into place.
6. Reconnect the electrical connector.
7. Reinstall the wheel liner.
NOTE:It is advised referring to an authorized dealer.
Side Indicators
The Side Indicators are LED. See an authorized 
dealer for replacement.
Rear Body Side Tail Lamps
Contain the following:
Position lights
Stop lights
Direction indicator
To replace the bulbs proceed as follows:
1. Open the liftgate.
2. Using a suitable tool remove fasteners.
Body Side Tail Lamp
WARNING!
Carry out the operation of replacing lamps only 
with the engine off. Also make sure that the 
engine is cold, to avoid the danger of burns.
1 — Bulb
1 — Fasteners Caps
8
22_MP_OM_EN_USC_t.book  Page 293   
         
        
        
     
        
        Page 297 of 344

SERVICING AND MAINTENANCE295
Reverse Lamps
1. Open the liftgate.
2. Using a suitable tool remove the access panel  for body side lamps, remove liftgate access 
cover for liftgate lamps.
Liftgate
3. Disconnect the electrical connector by pushing  the release.
4. Remove bulb and replace making sure it is  properly locked.
5. Reconnect the electrical connector.
6. Reinstall the access panels making sure they  are locked in correctly.
7. Finally close the tailgate. 3rd Stop Lamp
The CHMSL is LED. See an authorized dealer for 
replacement.
License Plate Lights
The License Plate light is LED. See an authorized 
dealer for replacement.
Replacing Interior Bulbs
Front Courtesy Light
To replace the bulbs proceed as follows:
1. Using a suitable tool remove the front 
courtesy light assembly.
Front Courtesy Light
 2. Release the retainer clips and bulb housing as 
shown.
Front Courtesy Bulb Housing
1 — Liftgate Access Covers
1 — Retaining Clips
2 — Bulb Housing
8
22_MP_OM_EN_USC_t.book  Page 295   
         
        
        
     
        
        Page 298 of 344

296SERVICING AND MAINTENANCE  
3. Replace the bulbs by pulling straight out of  bulb housing.
Front Courtesy Bulb Housing
4. Insert the new bulbs, making sure that they are  properly locked.
5. Reassemble the bulb housing and courtesy  light housing making sure that they are 
properly locked.
6. Install the front courtesy light, making sure  that it is properly locked. Dome Light Vanity Mirror — If Equipped
To replace the bulbs proceed as follows:
1. Lift the cover of the mirror and pull out the 
mirror frame with the mirror light cover 
attached.
2. Replace the bulb, releasing it from the side  contacts, and then insert the new bulb, making 
sure that it is properly locked between the 
contacts.
Visor
3. Reinstall the visor mirror light cover making  sure that it is properly locked.
4. Finally lower the visor mirror cover to the  mirror. Dome Light Glove Compartment
To replace the bulb proceed as follows:
1. Open the glove compartment.
2. Place your fingers inside the light assembly, 
pull the bulb to replace it.
Bulb Removal/Installation
3. Insert the new bulb, making sure it is properly  locked.
1 — Visor Mirror Cover
2 — Visor Mirror Light
22_MP_OM_EN_USC_t.book  Page 296   
         
        
        
     
        
        Page 299 of 344
SERVICING AND MAINTENANCE297
Dome Light
To replace the bulbs proceed as follows:
1. Lower the handle in the direction shown;  remove the dome light.
Grab Handle/Dome Light
2. Replace the bulb by removing it from the side  contacts.
Bulb
 3. Insert the new bulb, locking it between the 
contacts.
4. Reinstall the dome light.
Interior Cargo Lights
To replace the bulbs proceed as follows:
1. Using thumb with slight pressure – push bulb  holder to the side.
Bulb Holder
 2. Fully disengage the bulb holder from the 
housing.
Bulb Holder
3. Rotate bulb holder to replace bulb.
Bulb
8
22_MP_OM_EN_USC_t.book  Page 297   
         
        
        
     
        
        Page 300 of 344

298SERVICING AND MAINTENANCE  
NOTE:It is recommended to have your bulbs replaced by 
an authorized dealer.
TIRES 
TIRE SAFETY INFORMATION   
Tire safety information will cover aspects of the 
following information: Tire Markings, Tire 
Identification Numbers, Tire Terminology and 
Definitions, Tire Pressures, and Tire Loading.
Tire Markings 
Tire Markings
NOTE:
P (Passenger) — Metric tire sizing is based on US 
design standards. P-Metric tires have the letter 
“P” molded into the sidewall preceding the size 
designation. Example: P215/65R15 95H.
European — Metric tire sizing is based on 
European design standards. Tires designed to 
this standard have the tire size molded into the 
sidewall beginning with the section width. The 
letter "P" is absent from this tire size designa -
tion. Example: 215/65R15 96H.
LT (Light Truck) — Metric tire sizing is based on 
US design standards. The size designation for 
LT-Metric tires is the same as for P-Metric tires 
except for the letters “LT” that are molded into 
the sidewall preceding the size designation. 
Example: LT235/85R16.
Temporary spare tires are designed for tempo -
rary emergency use only. Temporary high pres -
sure compact spare tires have the letter “T” or 
“S” molded into the sidewall preceding the size 
designation. Example: T145/80D18 103M.
High flotation tire sizing is based on US design 
standards and it begins with the tire diameter 
molded into the sidewall. 
Example: 31x10.5 R15 LT.
WARNING!
Modifications or repair of the electrical system 
performed incorrectly and without taking into 
account the technical characteristics can 
cause malfunctions with the risk of fire.
Halogen lamps contain gas under pressure, in 
the event of breakage be careful of the projec -
tion of fragments of glass.
Halogen lamps must be handled by touching 
only the metallic part. If the transparent bulb 
is in contact with the fingers, reduces the 
intensity of the emitted light and you can also 
affect the life of the lamp. In case of acci -
dental contact, rub the bulb with a cloth damp -
ened with alcohol and allow to dry.
1 — US DOT Safety Standards 
Code (TIN)
2 — Size Designation
3 — Service Description
4 — Maximum Load
5 — Maximum Pressure
6 — Treadwear, Traction and 
Temperature Grades
22_MP_OM_EN_USC_t.book  Page 298