2023 HYUNDAI PALISADE lock

Seats & Safety System3-30
B0701EU05
Removal/Reinstallation
To remove the head restraint:
1.
Raise the head restraint as far as it can
go.
2. Press the head restraint release button M while pulling the head restraint up
N.
To reinstall the head restraint:
1. Put the head restraint poles into the holes O while pressing the release
button M.
2. Adjust the head restraint to the appropriate height.
Folding 3rd row headrest (except for
center)
B0705EU01
The headrest will fold down
automatically when folding the seatback.
To fold the headrest manually:

- Pull the strap.
To unfold the headrest manually:
- Raise the headrest manually.
Always be sure the headrest has
locked into position after you return
the seatback.
Information
The height of the 3rd row headrests
cannot be adjusted.

Seats & Safety System3-34
Air Ventilation Seats (if
equipped)
The air ventilation seats are provided
to cool the front seats by blowing air
through small vent holes on the surface
of the seat cushions and seatbacks.
When the operation of the air ventilation
seat is not needed, keep the air
ventilation seats OFF.
NOTICE
To prevent damage to the air ventilation
seats:

[ Never use a solvent such as paint
thinner, benzene, alcohol or gasoline
to clean the seats.

[ Avoid spilling liquids on the surface
of the front seats and seatbacks; this
may cause the air vent holes to block
and not work properly.

[ Do not place materials such as plastic
bags or newspapers under the seats.
They may block the air intake causing
malfunction of the air vent.

[ Do not change the seat covers. It may
damage the air ventilation seat.

[ If the air vents do not operate, restart
the vehicle. If there is no change,
have your vehicle inspected by an
authorized HYUNDAI dealer.
B0057KO01
B0057KO02
A: Front seat,
B: Rear seat

[Each time you push the switch,
the temperature setting of the seat
changed as shown below:

[ Front seat
2))

Seats & Safety System3-38
WARNING
Riding in an improper position
adversely affects the front passenger’s
seat belt warning system. It is important
for the driver to instruct the passenger
to properly be seated as instructed in
this manual.
Information

[ Although the front passenger seat is not
occupied, the seat belt warning light
will blink or illuminate for 6 seconds.

[ The front passenger’s seat belt warning
may operate when luggage is placed on
the front passenger seat.
Seat Belt Restraint System
WARNING
Improperly positioned seat belts may
increase the risk of serious injury
in an accident. Take the following
precautions when adjusting the seat
belt:

[Position the lap portion of the seat
belt as low as possible across your
hips, not on your waist, so that it fits
snugly.

[ Position one arm under the shoulder
belt and the other over the belt, as
shown in the illustration.

[ Always position the shoulder belt
anchor into the locked position at the
appropriate height.

[ Never position the shoulder belt
across your neck or face.

03
3-39
Front Seat Belt – Driver’s 3point
system with emergency locking
retractor
B0059KO05
To fasten your seat belt:
Pull the seat belt out of the retractor and
insert the me
tal tab (1) into the buckle
(2). There will be an audible “click” when
the tab locks into the buckle.
B0059KO06
You should place the lap belt portion
across your hips and the shoulder belt
portion across your chest.
The seat belt automatically adjusts to the
proper length after the lap belt portion
is adjusted manually so that it fits snugly
around your hips. If you lean forward in
a slow, easy motion, the belt will extend
and move with you.
If there is a sudden stop or impact, the
belt will lock into position. It will also lock
if you try to lean forward too quickly.
Information
If you are not able to smoothly pull
enough of the seat belt out from the
retractor, firmly pull the seat belt out and
release it. After release, you will be able to
pull the belt out smoothly.

Seats & Safety System3-40
Height adjustment
You can adjust the height of the shoulder
belt anchor t
o one of the four different
positions for maximum comfort and
safety.
The shoulder portion should be adjusted
so it lies across your chest and midway
over your shoulder nearest the door, not
over your neck.
„Front seat
B0059KO07
To adjust the height of the seat belt
anchor, lower or raise the height adjuster
into an appropriate position.
To raise the height adjuster, pull it up
M. To lower it, push it down O while
pressing the height adjuster button N.
Release the button to lock the anchor
into position. Try sliding the height
adjuster to make sure that it has locked
into position.
B0059KO11
To release your seat belt:
Press the release button M in the locking
buckle.
Once it is r

eleased, the belt should
automatically draw back into the
retractor. If this does not happen, check
the belt to be sure it is not twisted, then
try again.

03
3-41
Rear Seat Belt – Passenger’s 3point
system with convertible locking
retractor
This type of seat belt combines the
features of both an emergency locking
retractor seat belt and an automatic
locking retractor seat belt. Convertible
retractor type seat belts are installed
in the rear seat positions to help
accommodate the installation of child
restraint systems. Although a convertible
retractor is also installed in the front
passenger seat position, NEVER place
any infant/child restraint system in the
front seat of the vehicle.
To fasten your seat belt:
Pull the seat belt out of the retractor
and insert the me
tal tab into the buckle.
There will be an audible “click” when
the tab locks into the buckle. When
not securing a child restraint, the seat
belt operates in the same way as the
driver’s seat belt (Emergency Locking
Retractor Type). It automatically adjusts
to the proper length only after the lap
belt portion of the seat belt is adjusted
manually so that it fits snugly across your
hips.
When the seat belt is fully extended from
the retractor to allow the installation of
a child restraint system, the seat belt
operation changes to allow the belt to
retract, but not to extend (Automatic
Locking Retractor Type). Refer to the
“Using a Child Restraint System” section
in this chapter.
B0059KO11
To release your seat belt:
Press the release button M in the locking
buckle.
When it is r

eleased, the belt should
automatically draw back into the
retractor. If this does not happen, check
the belt to be sure it is not twisted, then
try again.
NOTICE
Although the seat belt retractor
provides the same level of protection
for seated passengers in either
emergency or automatic locking
modes, the emergency locking mode
allows seated passengers to move
freely in their seat while keeping
some tension on the belt. During a
collision or sudden stop, the retractor
automatically locks the belt to help
restrain your body.
To deactivate the automatic locking
mode, unbuckle the seat belt and allow
the belt to fully retract.

Seats & Safety System3-42
Second row center seatbelt
(3-point rear center seat belt)
B0059KO12
1. Take out the buckle B, which is stored
between the seat/seatback cushions.
2. Insert the metal plate
A into the
buckle B, until it clicks.
You can make sure its secure
fastening by pulling the seatbelt
webbing. The buckle with 'CENTER'
mark should be used for the 3-point
seatbelt.
3. Restore the buckle between the seat/ seatback cushion after unfastening
the seatbelt.
Rear center seatbelt (3rd row)
B0059KO08
To fasten your seatbelt:
1. Extract the tongue plate
A from the
hole on the belt assembly cover.
B0059KO09
2. Insert the tongue plate A into the
buckle B until an audible "click" is
heard, indicating the latch is locked.
Make sure the belt is not twisted.

03
3-43
B0059KO10
3. Pull out the tongue plate C from the
pocket. Pull the tongue plate C and
insert it into the buckle D until an
audible "click" is heard, indicating the
latch is locked. Make sure the belt is
not twisted.
When using the rear center seat belt, the
buckle with the "CENTER" mark must be
used.
Information
If you are not able to pull out the safety
belt from the retractor, firmly pull the belt
out and release it. After release, you will be
able to pull the belt out smoothly.
B0059KO13
To release your seatbelt:
1. Press the release button on the buckle
D and remove the tongue plate C.
B0059KO14
2. To retract the rear center seatbelt, insert the tongue C plate into the web
release hole B. Pull up on the seat belt
web and allow the webbing to retract
automatically. Insert the tongue plate
A into the hole on the belt assembly
cover.