2023 HYUNDAI I20 drive mode

6-66
Driving your vehicle
If you decide to pull a trailer?
Here are some important points if you
decide to pull a trailer:

[Consider using a sway control. You
can ask a trailer towbar dealer about
sway control.

[Do not do any towing with your
vehicle during its first 1,200 miles
(2,000 km) in order to allow the
engine to properly break in. Failure to
heed this caution may result in serious
engine or transmission damages.

[When towing a trailer, be sure to
consult a HYUNDAI authorised repairer
for further information on additional
requirements such as a towing kit, etc.

[Always drive your vehicle at a
moderate speed (less than 60 mph
(100 km/h)) or posted towing speed
limit.

[On a long uphill grade, do not exceed
45 mph (70 km/h) or the posted
towing speed limit, whichever is lower.

[Carefully observe the weight and load
limits provided in the following pages.
Trailer weight
OLMB053047
Tongue LoadTotal Trailer Weight
What is the maximum safe weight of a
trailer? It should never weigh more than
the maximum trailer weight with trailer
brakes. But even that can be too heavy.
It depends on how you plan to use your
trailer. For example, speed, altitude,
road grades, outside temperature and
how often your vehicle is used to pull
a trailer are all important. The ideal
trailer weight can also depend on any
special equipment that you have on your
vehicle.

07
7-89
OBC3070022
To turn off Smart Cruise Control
Press the Driving Assist button to turn
Smart Cruise Control system off.
Information
If your vehicle is equipped with Manual
Speed Limit Assist, press and hold the
Driving Assist button to turn off Smart
Cruise Control. However, Manual Speed
Limit Assist will turn on.
Based on DRIVE MODE
Smart Cruise Control will change
acceleration based on the drive mode
selected from Drive Mode Integrated
Control system. Refer to the following
chart.
Drive mode Smart Cruise Comtrol
COMFORT Normal
ECO Slow
SPORT Fast
Information
For more details on drive mode, refer to
“Drive Mode Integrated Control System”
VHFWLRQLQFKDSWHU
„Type A
OTM070141L
„Type B
ONX4E070090
Warning volume
With the engine on, select ‘Driver
DVVLVWDQFH

Driver assistance system
7-154
Operating order
Parking mode operates in the following
order:
1. Getting ready for parking
2. Selecting parking mode and type
3. Searching for parking space
4. Recognizing parking space
5. Search complete
6. Steering wheel control
7. Parking complete

[Parking Assist will help you
with parallel reverse parking or
perpendicular reverse.
OBC3070044R
1. Getting ready for parking
(1) With the engine turned on, depress
the brake pedal and shift the gear to
D (Drive).
- If the vehicle is driven above 3 mph
(5 km/h) after the engine is turned
on, Parking mode can be selected
when the gear is in N (Neutral)
(2) Press and hold the Parking/View
(
) button to turn on Parking Assist.
A message will appear on the cluster
and the Parking Safety (
) button
indicator light will illuminate.
[If the engine is turned on when the
gear is in N (Neutral), Exit mode
will be selected. Parking mode will
be selected automatically after the
vehicle has been driven.

[Parking Assist is turned off whenever
the engine is restarted. Press the
Parking/View (
) button to turn use
Parking Assist again.
2. Selecting parking mode and type
(1) Select parking mode by pressing the
Parking/View (
) button briefly.
Parking type will change whenever
the button is pressed. Right parallel
UHYHUVHSDUNLQJ

Driver assistance system
7-156
„Parallel reverse parking
OBC3070098TU
„Perpendicular reverse parking
OBC3070097TU
5. Search complete
(1) Whilst slowly driving forward to
search for a parking space, the

S3DUNLQJVSDFHIRXQG
TPHVVDJHZLOO
appear on the cluster with a beep
sound if the searching process is
complete.
Information
Even if Parking Assist is not being
operated by the driver, it searches for
a parking space at all times. Therefore,
when Parking mode is selected, the search
result (search/recognise/complete) will
appear on the cluster.
Information
OJX1070232R
[A] : Searching for parking space

Driver assistance system
7-158
OBC3070103TU
7. Parking complete
(1) Complete parking your vehicle by
following the instructions on the
cluster. If required, manually control
the steering wheel and complete
parking your vehicle.
(2) When using perpendicular reverse
parking, Parking Assist will complete
parking the vehicle without
completely entering the parking
space, considering stoppers, etc.
in the parking space. If necessary,
manually complete parking your
vehicle.
How to turn off Parking mode whilst
operating

[Press and hold the Parking/View ()
button in the following stage:
- Searching for parking space
- Select parking mode and type

[Press the Parking/View (
) button or
Parking Safety () button whilst the
steering wheel is being controlled.
Parking mode will cancel in the fol-
lowing conditions:

[When searching for parking space
- Shifting the gear to R (Reverse)
- The vehicle is above 18 mph (30
km/h)
- The parking space is narrow
- The steering wheel, gearshift,
braking, and drive controls are not
working normally
- ABS, TCS or ESC system operates
due to slippery road conditions

[When the steering wheel is being
controlled
- The steering wheel is steered
- Approximately 6 minutes have
passed after the steering wheel has
been controlled
- The steering wheel, gearshift,
braking, and drive controls are not
working normally
- ABS, TCS or ESC system operates
due to slippery road conditions

Driver assistance system
7-160
OBC3070044R
1. Getting ready for exit
(1) With the engine turned on, depress
the brake pedal and shift the gear to
P (Park) or N (Neutral).
(2) Press and hold the Parking/View
(
) button to turn on Parking Assist.
A message will appear on the cluster
and the Parking Safety (
) button
indicator light will illuminate.

[If the engine is turned on when the
gear is in N (Neutral), Exit mode
will be selected. Parking mode will
be selected automatically after the
vehicle has been driven.

[Parking Assist is turned off whenever
the engine is restarted. Press the
Parking/View (
) button to turn use
Parking Assist again.
.
OBC3070106TU
2. Selecting exit mode and type
(1) Select exit mode by pressing the
Parking/View (
) button briefly.
Parking type will change whenever
the button is pressed.
/HIWSDUDOOHOH[LW

07
7-163
How to turn off Exit mode whilst
operating

[Press the Parking/View () button or
Parking Safety () button.
Exit mode will cancel in the following
conditions:

[ When checking space to exit
- Shifting the gear to R (Reverse)
- The vehicle moves
- Not enough space to exit
- An object is detected within 2mm (79
in.) in the direction of exit
- The steering wheel, gearshift,
braking, and drive controls are not
working normally
- ABS, TCS or ESC system operates
due to slippery road conditions

[When the steering wheel is being
controlled
- The steering wheel is steered
- Approximately 6 minutes have
passed after the steering wheel has
been controlled
- The steering wheel, gearshift,
braking, and drive controls are not
working normally
- ABS, TCS or ESC system operates
due to slippery road conditions
OBC3070104TU
Additional instructions (messages)
When Parking Assist is operating, a
message may appear regardless of the
operating order. The messages will
appear according to the circumstances.
Follow the instructions provided whilst
using Parking Assist.
WARNING

[Always check surroundings for
pedestrians, animals or objects
before taking your foot off the brake
pedal.

[If the vehicle does not move even
though the brake pedal is not
depressed, check the surroundings
before depressing the accelerator
pedal.

[ If it is determined that the space is
too small when the vehicle is being
controlled to exit, Exit mode will be
canceled.

8-11
08
OBC3N081002AU
ONX4E080005
(1) Low Tyre Pressure Telltale/TPMS
Malfunction Indicator
(2) Low Tyre Pressure Position Telltale
and Tyre Pressure Telltale (Shown on
the LCD display)
Check tyre pressure
ONX4E040019

[You can check the tyre pressure in the
Warning mode on the cluster.
Refer to the “LCD Display Modes” in
chapter 4.

[Tyre pressure is displayed after a few
minutes of driving after initial engine
start up.

[If tyre pressure is not displayed when
the vehicle is stopped, “Drive to
display” message will appear. After
driving, check the tyre pressure.

[The displayed tyre pressure values
may differ from those measured with a
tyre pressure gauge.

[You can change the tyre pressure
unit in the User Settings mode on the
instrument cluster.
- psi, kpa, bar (Refer to “LCD Modes”
in chapter 4).
7<5(35(6685(021,725,1*6<67(0