2023 HYUNDAI I20 change time
[x] Cancel search: change timePage 311 of 649
6-38
Driving your vehicle
Using ABS
To obtain the maximum benefit from
your ABS in an emergency situation,
do not attempt to modulate your brake
pressure and do not try to pump your
brakes. Depress your brake pedal as
hard as possible.
When you apply your brakes under
conditions which may lock the wheels,
you may hear sounds from the brakes,
or feel a corresponding sensation in the
brake pedal. This is normal and it means
your ABS is active.
ABS does not reduce the time or
distance it takes to stop the vehicle.
Always maintain a safe distance from the
vehicle in front of you.
ABS will not prevent a skid that results
from sudden changes in direction, such
as trying to take a corner too fast or
making a sudden lane change. Always
drive at a safe speed for the road and
weather conditions.
ABS cannot prevent a loss of stability.
Always steer moderately when braking
hard. Severe or sharp steering wheel
movement can still cause your vehicle
to veer into oncoming traffic or off the
road.
On loose or uneven road surfaces,
operation of the anti-lock brake system
may result in a longer stopping distance
than for vehicles equipped with a
conventional brake system.
The ABS warning light (
) will stay
on for several seconds after the ignition
switch is in the ON position. During
that time, the ABS will go through self-
diagnosis and the light will go off if
everything is normal. If the light stays
on, you may have a problem with your
ABS. We recommend that you contact a
HYUNDAI authorised repairer as soon as
possible.
WARNING
If the ABS warning light () is on and
stays on, you may have a problem with
the ABS. Your power brakes will work
normally. To reduce the risk of serious
injury or death, we recommend that
you contact your HYUNDAI dealer as
soon as possible.
NOTICE
When you drive on a road having poor
traction, such as an icy road, and apply
your brakes continuously, the ABS will
be active continuously and the ABS
warning light (
) may illuminate. Pull
your vehicle over to a safe place and
turn the engine off.
Restart the engine. If the ABS warning
light is off, then your ABS system is
normal.
Otherwise, you may have a problem
with your ABS system. We recommend
that you contact a HYUNDAI authorised
repairer as soon as possible.
i Information
: K H Q \ R X M X P S V W D U W \ R X U Y H K L F O H
E H F D X V H R I D G U D L Q H G E D W W H U \ W K H $ % 6
Z D U Q L Q J O L J K W
P D \ W X U Q R Q D W W K H
V D P H W L P H 7 K L V K D S S H Q V E H F D X V H R I W K H
O R Z E D W W H U \ Y R O W D J H , W G R H V Q R W P H D Q \ R X U
$ % 6 L V P D O I X Q F W L R Q L Q J + D Y H W K H E D W W H U \
U H F K D U J H G E H I R U H G U L Y L Q J W K H Y H K L F O H
Page 343 of 649
6-70
Driving your vehicle
Driving with a trailer
Towing a trailer requires a certain
amount of experience. Before setting
out for the open road, you must get to
know your trailer. Acquaint yourself with
the feel of handling and braking with the
added weight of the trailer. And always
keep in mind that the vehicle you are
driving is now longer and not nearly as
responsive as your vehicle is by itself.
Before you start, check the trailer towbar
and platform, safety chains, electrical
connector(s), lights, tyres and brakes.
During your trip, occasionally check
to be sure that the load is secure, and
that the lights and trailer brakes are still
working.
Distance
Stay at least twice as far behind the
vehicle ahead as you would when driving
your vehicle without a trailer. This can
help you avoid situations that require
heavy braking and sudden turns.
Passing
You will need more passing distance up
ahead when you’re towing a trailer. And,
because of the increased vehicle length,
you’ll need to go much farther beyond
the passed vehicle before you can return
to your lane.
Backing up
Hold the bottom of the steering wheel
with one hand. Then, to move the trailer
to the left, move your hand to the left.
To move the trailer to the right, move
your hand to the right. Always back up
slowly and, if possible, have someone
guide you.
Making turns
When you’re turning with a trailer, make
wider turns than normal. Do this so your
trailer won’t strike soft shoulders, kerbs,
road signs, trees, or other objects. Avoid
jerky or sudden manoeuvres. Signal well
in advance.
Turn signals
When you tow a trailer, your vehicle has
to have a different turn signal flasher and
extra wiring. The green arrows on your
instrument panel will flash whenever you
signal a turn or lane change. Properly
connected, the trailer lights will also
flash to alert other drivers you’re about
to turn, change lanes, or stop.
When towing a trailer, the green arrows
on your instrument panel will flash for
turns even if the bulbs on the trailer
are burned out. Thus, you may think
drivers behind you are seeing your
signals when, in fact, they are not. It’s
important to check occasionally to be
sure the trailer bulbs are still working.
You must also check the lights every
time you disconnect and then reconnect
the wires.
WARNING
Do not connect a trailer lighting system
directly to your vehicle’s lighting
system. Use an approved trailer wiring
harness.
Failure to do so could result in damage
to the vehicle electrical system and/or
personal injury.
We recommend that you have the
system checked by a HYUNDAI
authorised repairer as soon as possible.
Page 388 of 649
Driver assistance system
7-42
WARNING
Take the following precautions when
using Blind-Spot Safety system:
[ For your safety, change the Settings
after parking the vehicle at a safe
location.
[ If any other function’s warning
message is displayed or audible
warning is generated, Blind-Spot
Safety system’s warning message
may not be displayed and audible
warning may not be generated.
[ You may not hear the warning sound
of Blind-Spot Safety system if the
surrounding is noisy.
[ Blind-Spot Safety system may warn
the driver late or may not warn the
driver depending on the road and
driving conditions.
[ Driver should maintain control of the
vehicle at all times. Do not depend on
Blind-Spot Safety system.
[ Never operate Blind-Spot Safety
system on people, animal, objects,
etc. It may cause serious injury or
death.
Blind-Spot Collision Warning
malfunction and limitations
Blind-Spot Collision Warning
malfunction
OTM070099L
When Blind-Spot Safety system is not
working properly, the ‘Check Blind-
6 S R W 6 D I H W \ V \ V W H PT Z D U Q L Q J P H V V D J H
will appear on the cluster for several
seconds, and the master (
) warning
light will illuminate on the cluster.
We recommend that the system be
inspected by a HYUNDAI authorised
repairer.
OTM070100L
When the outside rearview mirror
warning light is not working properly,
the ‘Check side view mirror warning
O L J K WT R U S & K H F N R X W V L G H P L U U R U Z D U Q L Q J
L F R QT Z D U Q L Q J P H V V D J H Z L O O D S S H D U R Q
the cluster for several seconds, and the
master (
) warning light will illuminate
on the cluster. We recommend that the
function be inspected by a HYUNDAI
authorised repairer.
Page 390 of 649
Driver assistance system
7-44
[ There is a fixed object near the
vehicle, such as sound barriers,
guardrails, central dividers, entry
barriers, street lamps, signs,
tunnels, walls, etc. (including double
structures)
[ Driving in large areas where there are
few vehicles or structures (i.e. desert,
meadow, suburb, etc.)
[ Driving through a narrow road where
trees or grass are overgrown
[ Driving on a wet road surface, such as
a puddle on the road
[ The other vehicle drives very close
behind your vehicle, or the other
vehicle passes by your vehicle in close
proximity
[ The speed of the other vehicle is very
fast that it passes by your vehicle in a
short time
[ Your vehicle passes by the other
vehicle
[ Your vehicle changes lane
[ Your vehicle has started at the same
time as the vehicle next to you and
has accelerated
[ The vehicle in the next lane moves
two lanes away from you, or when the
vehicle two lanes away moves to the
next lane from you
[ A trailer or carrier is installed around
the rear corner radar
[ The bumper around the rear corner
radar is covered with objects, such as
a bumper sticker, bumper guard, bike
rack, etc.
[ The bumper around the rear corner
radar is impacted, damaged or the
radar is out of position
[ Your vehicle height is low or high
due to heavy loads, abnormal tyre
pressure, etc.Blind-Spot Safety system may not
operate normally, or the function
may operate unexpectedly when the
following objects are detected:
[ A motorcycle or bicycle is detected
[ A vehicle such as a flat trailer is
detected
[ A big vehicle such as a bus or truck is
detected
[ A moving obstacle such as a
pedestrian, animal, shopping cart or a
baby stroller is detected
[ A vehicle with low height such as a
sports car is detected
Page 399 of 649
07
7-53
OBC3070125R
Collision-Avoidance Assist (whilst
driving)
[ To warn the driver of a collision, the
warning light on the outside rearview
mirror will blink and a warning
message will appear on the cluster.
At the same time, an audible warning
will sound and the steering wheel will
vibrate (if equipped).
[ The function will operate when your
vehicle speed is between 40~120
mph (60~200 km/h) and both lane
markings of the driving lane are
detected.
[ Emergency braking will be assisted to
help prevent collision with the vehicle
in the blind spot area.
WARNING
[ Collision-Avoidance Assist will
be canceled under the following
circumstances:
- Your vehicle enters the next lane by
a certain distance
- Your vehicle is away from the
collision risk
- The steering wheel is sharply
steered
- The brake pedal is depressed
- Forward Collision-Avoidance Assist
is operating
[ After function operation or lane
change, you must drive to the centre
of the lane. The function will not
operate if the vehicle is not driven in
the centre of the lane.
Page 401 of 649
07
7-55
WARNING
Take the following precautions when
using Blind-Spot Safety system:
[ For your safety, change the Settings
after parking the vehicle at a safe
location.
[ If any other function’s warning
message is displayed or audible
warning is generated, Blind-Spot
Safety system’s warning message
may not be displayed and audible
warning may not be generated.
[ You may not hear the warning sound
of Blind-Spot Safety system if the
surrounding is noisy.
[ Blind-Spot Safety system may not
operate if the driver applies the brake
pedal to avoid collision.
[ When Blind-Spot Safety system
is operating, braking control by
the function will automatically
cancel when the driver excessively
depresses the accelerator pedal or
sharply steers the vehicle.
[ During Blind-Spot Safety system
operation, the vehicle may stop
suddenly injuring passengers and
shifting loose objects. Always have
the seat belt on and keep loose
objects secured.
[ Even if there is a problem with Blind-
Spot Safety system, the vehicle’s
basic braking performance will
operate normally.
[ Blind-Spot Safety system does not
operate in all situations or cannot
avoid all collisions. [ Blind-Spot Safety system may warn
the driver late or may not warn the
driver depending on the road and
driving conditions.
[ Driver should maintain control of the
vehicle at all times. Do not depend on
Blind-Spot Safety system. Maintain
a safe braking distance, and if
necessary, depress the brake pedal
to reduce driving speed or to stop the
vehicle.
[ Never operate Blind-Spot Safety
system on people, animal, objects,
etc. It may cause serious injury or
death.
WARNING
The brake control may not operate
properly depending on the status of
ESC (Electronic Stability Control).
There will only be a warning when:
- The ESC (Electronic Stability Control)
warning light is on
- ESC (Electronic Stability Control) is
engaged in a different function
Page 403 of 649
07
7-57
CAUTION
Turn off Blind-Spot Safety system to
install a trailer, carrier, etc., or remove
the trailer, carrier, etc. to use Blind-
Spot Safety system.
Limitations of Blind-Spot Collision-
Avoidance Assist
Blind-Spot Safety system may not
operate normally, or the function
may operate unexpectedly under the
following circumstances:
[ There is inclement weather, such as
heavy snow, heavy rain, etc.
[ The rear corner radar is covered with
snow, rain, dirt, etc.
[ The temperature around the rear
corner radar is high or low
[ Driving on a highway (or motorway)
ramp
[ The road pavement (or the peripheral
ground) abnormally contains metallic
components (i.e. possibly due to
subway construction)
[ There is a fixed object near the
vehicle, such as sound barriers,
guardrails, central dividers, entry
barriers, street lamps, signs,
tunnels, walls, etc. (including double
structures)
[ Driving in large areas where there are
few vehicles or structures (i.e. desert,
meadow, suburb, etc.)
[ Driving through a narrow road where
trees or grass are overgrown
[ Driving on a wet road surface, such as
a puddle on the road
[ The other vehicle drives very close
behind your vehicle, or the other
vehicle passes by your vehicle in close
proximity[ The speed of the other vehicle is very
fast that it passes by your vehicle in a
short time
[ Your vehicle passes by the other
vehicle
[ Your vehicle changes lane
[ Your vehicle has started at the same
time as the vehicle next to you and
has accelerated
[ The vehicle in the next lane moves
two lanes away from you, or when the
vehicle two lanes away moves to the
next lane from you
[ A trailer or carrier is installed around
the rear corner radar
[ The bumper around the rear corner
radar is covered with objects, such as
a bumper sticker, bumper guard, bike
rack, etc.
[ The bumper around the rear corner
radar is impacted, damaged or the
radar is out of position
[ Your vehicle height is low or high
due to heavy loads, abnormal tyre
pressure, etc.
Blind-Spot Safety system may not
operate normally, or the function
may operate unexpectedly when the
following objects are detected:
[ A motorcycle or bicycle is detected
[ A vehicle such as a flat trailer is
detected
[ A big vehicle such as a bus or truck is
detected
[ A moving obstacle such as a
pedestrian, animal, shopping cart or a
baby stroller is detected
[ A vehicle with low height such as a
sports car is detected
Page 418 of 649
Driver assistance system
7-72
OBC3070090TU
Warning overspeed
When driving at a speed higher than
the displayed speed limit, the red speed
limit indicator will blink.
OBC3070091ROBC3070092R
Changing set speed
If the speed limit of the road changes
during the operation of Manual Speed
Limit Assist or Smart Cruise Control,
an arrow in the direction of up or down
is displayed to inform the driver that
the set speed needs to be changed. At
this time, the driver can change the set
speed according to the speed limit by
using the + or – switch on the steering
wheel.
WARNING
[ If the Speed limit tolerance is set over
‘0’, the set speed will change to a
higher speed than the speed limit of
the road. If you want to drive below
the speed limit, set the Speed limit
tolerance under '0' or use the
– switch on the steering wheel to
lower the set speed.
[ Even after changing the set speed
according to the speed limit of the
road, the vehicle can still be driven
over the speed limit. If necessary,
depress the brake pedal to reduce
your driving speed.
[ If the speed limit of the road is under
20 mph (30 km/h), the set speed
change function will not work.
[ Intelligent Speed Limit Assist
operates using the speed unit in the
instrument cluster set by the driver.
If the speed unit is set to a unit other
than the speed unit used in your
country, Intelligent Speed Limit
Assist may not operate properly.
Information