2023 HONDA ACCORD display

uuWhen Driving uVehicle Stability AssistTM (VSA ®), aka Electronic Stability Control (ESC), System
314
Driving
You can turn the system on and off us ing the driver information interface.
2Switching the Display P. 112
2 Vehicle Stability Assist Mode P. 122
Your vehicle will have normal braking an d cornering ability, but traction control
function will be less effective.
VSA ® is turned on every time you start the engi ne, even if you turned it off the last
time you drove the vehicle.
■VSA ® On and Off1 Vehicle Stability AssistTM (VSA ®), aka Electronic Stability Control
(ESC), System
In certain unusual conditions when your vehicle gets
stuck in shallow mud or fr esh snow, it may be easier
to free it with the VSA ® temporarily switched off.
When the VSA ® system is off, the traction control
function becomes less effective. This allows for the
wheels to spin more freely at low speed. You should
only attempt to free your vehicle with the VSA ® off if
you are not able to free it when the VSA ® is on.
Immediately after freeing your vehicle, be sure to
switch VSA ® on again. We do not recommend driving
your vehicle with the VSA ® system switched off.
You may hear a motor sound coming from the
engine compartment while system checks are being
performed immediately after starting the engine or
while driving. This is normal.
23 ACCORD 4D US PET MAP-3130A6000_01.book 314 ページ ２０２２年１０月１９日　水曜日　午前１１時４９分

Continued319
uuWhen Driving uTire Pressure Monitoring System (TPMS)*
Driving
When you calibrate the TPMS, do the
following.
1. Roll the right selector wheel to select
Vehicle settings , then press the right
selector wheel.
u TPMS calibration appears on the
display.1TPMS Calibration
If the tire chains are installed, remove them before
calibrating the TPMS.
If the low tire pressure/TPMS indicator comes on even
when the properly inflated specified regular tires are
installed, have your vehi cle checked by a dealer.
We recommend that the tires be replaced with the
same brand, model, and size as the originals. Ask a
dealer for details.
23 ACCORD 4D US PET MAP-3130A6000_01.book 319 ページ ２０２２年１０月１９日　水曜日　午前１１時４９分

320
uuWhen Driving uTire Pressure Monitoring System (TPMS)*
Driving
2. Press the right selector wheel.
u The display switches to the
customization setup screen, where you
can select Cancel or Calibrate .
3. Roll the right selector wheel and select
Calibrate , then press the right selector
wheel.
u Calibration started screen appears,
then the display returns to the
customization menu screen.
• If the Calibration failed to start message
appears, repeat step 4.
• The calibration pr ocess finishes
automatically.
23 ACCORD 4D US PET MAP-3130A6000_01.book 320 ページ ２０２２年１０月１９日　水曜日　午前１１時４９分

uuWhen Driving uBlind Spot Information System*
324
Driving
■When the system detects a vehicle
Blind spot information system alert indicator:
Located on the outside door mirror on both
sides.
Comes on when:
• A vehicle approaches you from behind to
overtake you at a speed difference of no
more than about 31 mph (50 km/h).
• You pass a vehicle at a speed difference of
no more than about 12 mph (20 km/h).
Blinks and a beeper sounds when:
You use the turn signal lever to signal a turn in
the direction of the detected vehicle while the
blind spot information system alert indicator is
on. u The beeper sounds three times.1Blind Spot Information System*
For proper blind spot information system operation:•Always keep the rear bumper and area around the
radar sensors clean.
•Do not cover the rear bumper corner area with
labels or sticke rs of any kind.
The system is for your convenience only. Even if an
object is within the alert zone, the following
situations may occur:
•The blind spot informatio n system alert indicator
does not come on and the message Blind spot
information system not available appears on
the driver information interface.
•The blind spot informatio n system alert indicator
may come on even with the message displayed.
The Vehicle Stability Assist
TM (VSA ®) system, Adaptive
Cruise Control (ACC) with Low Speed Follow, low tire
pressure/TPMS
*, safety support, and parking brake
and brake system (amber) indicators may come on in
amber along with a message in the gauge when you
set the power mode to ON after reconnecting the
battery.
Drive a short distance at more than 12 mph (20
km/h). Each indicator should go off. If any do not,
have your vehicle ch ecked by a dealer.
Comes On
Blinks
* Not available on all models
23 ACCORD 4D US PET MAP-3130A6000_01.book 324 ページ ２０２２年１０月１９日　水曜日　午前１１時４９分

Continued325
uuWhen Driving uBlind Spot Information System*
Driving
You can turn the system on and off using the driver information interface.
2 Switching the Display P. 112
2 Safety Support P. 121
The blind spot information system will stay on the previously selected on or off
setting each time you start the engine.
■Blind Spot Information System On and Off1Blind Spot Information System*
You can change the settings for the blind spot
information system.
2 Vehicle Settings P. 126
* Not available on all models
23 ACCORD 4D US PET MAP-3130A6000_01.book 325 ページ ２０２２年１０月１９日　水曜日　午前１１時４９分

uuHonda Sensing ®u Collision Mitigation Braking SystemTM (CMBSTM)
334
Driving
You can turn the system on and off us ing the driver information interface.
2Switching the Display P. 112
2 Safety Support P. 121
The CMBSTM is turned on every time you start th e engine, even if you turned it off
the last time you drove the vehicle.
■CMBSTM On and Off1 Collision Mitigation Braking SystemTM (CMBSTM)
You cannot turn the CMBS
TM off while driving.
The CMBS
TM may automatically shut off, and the
safety support indicator (amb er) will come and stay
on under certain conditions: 2 CMBS
TM Conditions and Limitations P. 335
The Vehicle Stability Assist
TM (VSA ®) system, Adaptive
Cruise Control (ACC) with Low Speed Follow, low tire
pressure/TPMS
*, safety support, and parking brake
and brake system (amber) indicators may come on in
amber along with a message in the gauge when you
set the power mode to ON after reconnecting the
battery.
Drive a short distance at more than 12 mph (20 km/h).
Each indicator should go off. If any do not, have your
vehicle checked by a dealer.
Have your vehicle checked by a dealer if you find any
unusual behavior of the system (e.g., the warning
message appears too frequently).
* Not available on all models
23 ACCORD 4D US PET MAP-3130A6000_01.book 334 ページ ２０２２年１０月１９日　水曜日　午前１１時４９分

Continued345
uuHonda Sensing ®u Adaptive Cruise Control (ACC) with Low Speed Follow
Driving
When ACC with Low Speed Follow starts
operating, the vehicle icon, interval bars and
set speed appear on the gauge.1Adaptive Cruise Control (ACC) with Low Speed Follow
•On roads with slippery or icy surfaces. The wheels
may spin out and your vehi cle may lose the control
on the condition.
•On roads with steep uphill or steep downhill slopes.•On roads with undulating slopes.
1To Set the Vehicle Speed
The Vehicle Stability Assist
TM (VSA ®) system, Adaptive
Cruise Control (ACC) with Low Speed Follow, low tire
pressure/TPMS
*, safety support, and parking brake
and brake system (amber) indicators may come on in
amber along with a message in the gauge when you
set the power mode to ON after reconnecting the
battery.
Drive a short distance at more than 12 mph (20 km/h).
Each indicator should go off. If any do not, have your
vehicle checked by a dealer.
You can switch the displayed set speed
measurements on the driver information interface
between mph and km/h.
2 Vehicle Settings P. 126
2 Speed/distance units P. 123Set Vehicle Speed
Set Vehicle Interval
* Not available on all models
23 ACCORD 4D US PET MAP-3130A6000_01.book 345 ページ ２０２２年１０月１９日　水曜日　午前１１時４９分

Continued357
uuHonda Sensing ®u Adaptive Cruise Control (ACC) with Low Speed Follow
Driving
To cancel ACC with Low Speed Follow, do any
of the following:
• Press the CANCEL button.
u The indicator (green) on the gauge
changes to the indicator (white).
• Press the button.
u indicator (green) goes off.
• Depress the brake pedal while the vehicle is
moving forward.
u The indicator (green) on the gauge
changes to the indicator (white).
■To Cancel1To Cancel
Resuming the prior set speed: After you have
canceled ACC with Low Speed Follow, you can
activate the ACC with Low Speed Follow with the
prior set speed displayed on the gauge (in gray) by
pressing the RES/+/SET/− switch up even if the
vehicle is stopped.
When you turn the ACC with Low Speed Follow off
by pressing the CANCEL button or depressing the
brake pedal, the prior set speed is displayed on the
gauge in gray.
When pressing the RES/+/SET/− switch up, the ACC
with Low Speed Follow is activated with displayed
speed.
If the indicator (white) is displayed and you press
the RES/+ /SET/− switch up, but no prior set speed (in
gray) is displayed, the sp eed will be set to your
vehicle's current speed.
Prior Set Speed (gray)
(white)
CANCEL Button Button
23 ACCORD 4D US PET MAP-3130A6000_01.book 357 ページ ２０２２年１０月１９日　水曜日　午前１１時４９分