2023 GENESIS G90 mirror

5-50
Convenience Features
INTEGRATED MEMORY SYSTEM
ORS051033
ORS051034
ORS051035
A : Driver’s seat,
B : Front passenger’s seat,
C : Rear seat (if equipped)
Integrated Memory System for the
driver’s seat is provided to store and
recall the following memory settings with
a simple button operation.

[Seat position

[Steering wheel position (power
adjustment)

[Side view mirror position

[Head-Up Display (HUD) position and
brightness (if equipped)
WARNING
Never attempt to operate the
integrated memory system while the
vehicle is moving.
This could result in loss of control, and
an accident causing death, serious
injury, or property damage.
Information

[If the battery is disconnected, the
memory settings will be erased.

[If integrated memory system does not
operate normally, have the system
inspected by an authorized retailer of
Genesis Branded products.

5-51
05
Storing Memory Positions
1. Shift to P (Park) while the Engine
Start/Stop button is in the ON
position.
2. Adjust the seat position, side view
mirror position, steering wheel
position and head-up display height/
brightness to the desired position.
3. Press and hold one of the memory
buttons (1, 2 or 3). The system will
beep twice when the memory has
been successfully stored.
‘Settings 1 (2 or 3) saved’ will appear
on the cluster LCD display.
Recalling Memory Positions
1. Shift to P (Park) while the Engine
Start/Stop button is in the ON
position.
2. Press the desired memory button (1,
2 or 3). The system will beep once,
and then the seat position, side
view mirror position, steering wheel
position and head-up display height/
brightness will automatically adjust to
the stored positions.
‘Settings 1 (2 or 3) applied’ will appear
on the cluster LCD display.
If you press the corresponding button
which the setting is being recalled, the
setting will temporarily deactivate. If you
press the other buttons, the setting of
the pressed button will activate.
For example, if you press number 1
button with the number 1 setting in
operation, the setting will temporarily
deactivate. If you press the number
2 button, the number 2 setting will
activate.
If you adjust the seat, side view mirror,
steering wheel or head-up display while
recalling the stored positions, the pre-set
settings will become ineffective.
Information

[Up to 3 memories for front seats and
up to 2 memories for rear seats can be
saved.

[2QO\WKHGULYHU

5-54
Convenience Features
The Smart Posture Care system
automatically provides a healthy posture
(position) for the driver’s back, and sets
the steering wheel, side view mirrors,
head-up display positions according to
the driver’s body measurements.
Information
,IWKH6HDW3RVWXUH&DUHV\VWHPGRHVQRW
operate normally, have the system checked
by an authorized retailer of Genesis
Branded products.
OJWEV051211N
1. Check that the gear is in P (Park) while
the Engine Start/Stop button is in the
ON position.
2. 6HOHFW
S6HWXS

5-61
05
MIRRORS
Inside Rearview Mirror
Before driving your vehicle, check to
see that your inside rearview mirror is
properly positioned. Adjust the rearview
mirror so that the view through the rear
window is properly centered.
WARNING
Make sure your line of sight is not
obstructed. Do not place objects in the
rear seat, cargo area, or behind the rear
headrests which could interfere with
your vision through the rear window.
WARNING
To prevent serious injury during an
accident or deployment of the air bag,
do not modify the rearview mirror and
do not install a wide mirror.
WARNING
NEVER adjust the mirror while driving.
This may cause loss of vehicle control
resulting in an accident.
NOTICE
When cleaning the mirror, use a paper
towel or similar material dampened
with glass cleaner. Do not spray glass
cleaner directly on the mirror as this
may cause the liquid cleaner to enter
the mirror housing.
Electrochromic mirror (ECM) with
HomeLink® system
Your vehicle may be equipped with
a Gentex Automatic-Dimming Mirror
with an Integrated HomeLink® Wireless
Control System.
During nighttime driving, this feature
will automatically detect and reduce
rearview mirror glare. The HomeLink®
Universal Transceiver allows you to
activate your garage door(s), electric
gate, home lighting, etc.
ORS052039N
M HomeLink Channel 1
N HomeLink Channel 2
O HomeLink Channel 3
P Garage Door Opener Status Indicator:
Closing or Closed
Q HomeLink Operation Indicator
R Garage Door Opener Status Indicator:
Opening or Opened
S HomeLink User Interface Indicator

5-65
05
3) Two-Way Communication
3URJUDPPLQJ)RUVHOHFWJDUDJHGRRU
openers)
If your garage door opener has the
‘myQ’ logo on its side, your opener
likely has Two-Way Communication
capability. HomeLink has the capability
to establish Two-Way Communication
with your garage door opener. HomeLink
can receive and display “closing”
or “opening” status messages from
compatible garage door openers. At
any time, Home-Link can also recall
and display the last recorded status
communicated by the garage door
opener to indicate your garage door
being “closed” or “opened”.
To check if your garage door opener is
compatible with this feature, refer to
www.homelink.com/compatible/Two-
way-Communication. If your garage
door opener has this functionality, AND
the Two-Way Communication indicators
P, R in the mirror appear while the
garage door is opening/closing, then
no further steps are needed. Two-Way
Communication Programming is already
complete. However, if your garage door
opener has this functionality, AND the
Two-Way Communication indicators P,
R in the mirror DO NOT appear while
the garage door is opening/closing, use
the following instructions to enable this
functionality.
1. In your vehicle, press and hold the
programmed HomeLink button for 2
seconds, then release. Confirm that
the garage door is moving. AFTER it
stops, you will have one minute to
complete the following steps:
ÃA ladder and/or second person may
simplify the following steps.2. On your garage door opener in your
garage, locate the “Learn” button
(usually near where the hanging
antenna wire is attached to the garage
door opener). If there is difficulty
locating this button, reference the
device’s owner’s manual.
3. Press and release the “Learn” button.
4. A light on your garage door opener
may flash, and your Two-Way
Communication indicators P, R in
your vehicle may flash, confirming
completion of the process.
5. Return to the vehicle and firmly
press and release the programmed
HomeLink button to activate
your garage door. The Two-Way
Communication indicators P, R flash
in orange when the door is moving.
Do not make any additional button
presses until AFTER the garage door
has come to a complete stop.
6. Your Two-Way Communication
programming is now complete.
Information
If your garage door opener has Two-
:D\&RPPXQLFDWLRQIXQFWLRQDOLW\
it is possible for HomeLink to stop
functioning the garage door shortly
after initial programming, IF the Two-
:D\&RPPXQLFDWLRQ3URJUDPPLQJ
wasn’t properly completed. This
usually happens after the first 10 times
a programmed HomeLink button is
pressed. If you experience this, completing
the “Programming a New HomeLink
%XWWRQ

5-67
05
2) Two-Way Communication Display
Behavior
OJWEV051283N
1. Press and release one of the
programmed HomeLink buttons (M,
N or O).
ORS052309N
2. The indicator P and R operates as
below, if your garage door opener
has Two-Way Communication
functionality.
[If the indicator P flashes in Orange,
it indicates that the garage door is
“Closing”.

[The indicator P turns solid green once
the garage door has closed.

[If the indicator R flashes in Orange,
it indicates that the garage door is
“Opening”.

[The indicator R turns solid green once
the garage door has fully opened.

[If the indicator P or R does not
turn to green, it indicates that the
last status of garage door was not
received properly. The HomeLink
mirror tries to receive the last known
status of the garage door for a few
seconds.
3) Recalling Garage Door Status
HomeLink mirror with Two-Way
Communication provides a way to view
the last stored message from the garage
door opener. In order to recall the last
known status of the last activated device,
press the buttons “1 and 2” OR “2 and 3”
simultaneously.

[If the indicator P appears solid Green,
it indicates that the last activated
device was “closed” properly.

[If the indicator R appears solid Green,
it indicates that the last activated
device was “open” properly.

5-71
05
Side View Mirrors
ORS051040
Your vehicle is equipped with both
left-hand and right-hand side view
mirrors. The mirrors can be adjusted
remotely with the remote switch. The
side view mirrors can be folded to help
prevent damage when going through
an automatic car wash or when passing
through a narrow street.
The right side view mirror is convex.
Objects seen in the mirror are closer than
they appear.
Use the inside side view mirror or look
back directly to determine the actual
distance of other vehicles prior to
changing lanes.
Make sure to adjust the side view mirrors
to your desired position before you begin
driving.
WARNING
Do not adjust or fold the side view
mirrors while driving. This may cause
loss of vehicle control resulting in an
accident.
NOTICE

[Do not scrape ice off the mirror face;
this may damage the surface of the
glass.

[If the mirror is jammed with ice, do
not adjust the mirror by force. Use
an approved de-icer (not radiator
antifreeze) spray, or a sponge or soft
cloth with very warm water, or move
the vehicle to a warm place and
allow the ice to melt.

[Do not clean the mirror with harsh
abrasives, fuel or other petroleum
based cleaning products.

5-72
Convenience Features
Adjusting the rearview mirrors
ORS051042
ORS051041
Adjusting the rearview mirrors:
1. Turn the outer ring to the left or right
M to select the rearview mirror you
would like to adjust.
2. Use the mirror adjustment control
switch N to position the selected
mirror up, down, left or right.
3. After adjustment, return the outer
ring to the center position to prevent
inadvertent adjustment.
NOTICE

[The mirrors stop moving when
they reach the maximum adjusting
angles, but the motor continues to
operate while the switch is pressed.
Do not press the switch longer than
necessary, because this can damage
the motor.

[Do not attempt to adjust the
rearview mirrors by hand, because
this can damage the motor.