Page 246 of 676
5-105
05
Parking lamp (()
ORS051269
The parking lamp, license plate lamp and
instrument panel lamp are turned ON.
Headlight (()
ORS051270
The headlight, parking lamp, license
plate lamp and instrument panel lamp
are turned ON.
Information
The Engine Start/Stop button must be in
W K H 2 1 S R V L W L R Q W R W X U Q R Q W K H K H D G O L J K W
High Beam Operation
ORS051271L
To turn on the high beam headlight, push
the lever away from you. The lever will
return to its original position.
The high beam indicator will light when
the headlight high beams are switched
on.
To turn off the high beam headlight, pull
the lever towards you. The low beams
will turn on.
ORS051273L
To flash the high beam headlight, pull the
lever towards you, then release the lever.
The high beams will remain ON as long
as you hold the lever towards you.
Page 248 of 676
5-107
05
+ H D G O L J K W ' H O D \ ) X Q F W L R Q
If the Engine Start/Stop button is in the
ACC position or the OFF position with
the headlights ON, the headlights (and/
or parking lamps) remain on for about
5 minutes. However, if the driver’s door
is opened and closed, the headlights
are turned off after 15 seconds. Also,
with the vehicle off if the driver’s door is
opened and closed, the headlights (and/
or parking lamps) are turned off after 15
seconds.
The headlights (and/or parking lamps)
can be turned off by pressing the lock
button on the smart key twice or turning
the headlight switch to the OFF or AUTO
position.
You can enable the headlight delay
I X Q F W L R Q E \ V H O H F W L Q J S 6 H W X S
Page 250 of 676
5-109
05
[ Front door lamp ():
The front or rear room lamps come
on when the front or rear doors are
opened. When doors are unlocked
by the smart key, the front and rear
lamps come on for approximately
30 seconds as long as any door
is not opened. The front and rear
room lamps go out gradually after
approximately 30 seconds when the
door is closed. However, if the Engine
Start/Stop button is in the ON position
or all doors are locked, the front and
rear lamps will turn off. If a door is
opened with the Engine Start/Stop
button in the ACC position or the OFF
position, the front and rear lamps will
stay on for about 5 minutes.
[ Front room lamp (
)
Press the button to turn on the room
lamp for the front and rear seats.
Press the button again to turn off all
the lamps.
Information
7 R D G M X V W W K H O L J K W V X V L Q J W K H U H D U D U P U H V W
touchscreen, press from the left side
menu on the touchscreen.
Rear Lamps
ORS051079
ORS051251L
A : Rear seat (if equipped)
B : Rear seat armrest touchscreen (if equipped)
[ : Touch the icon to turn
either lamp on or off.
[
: Touch the icon to turn the lamp
on or off.
Information
7 R D G M X V W W K H O L J K W V X V L Q J W K H U H D U D U P U H V W
touchscreen, press from the left side
menu on the touchscreen.
Page 254 of 676
5-113
05
Puddle Lamp
ORS051084L
Welcome light
When all doors (and trunk) are closed
and locked, the puddle lamp will turn
on for 15 seconds if any of the below is
performed.
[ The doors are unlocked by the smart
key.
[ The outside door handle touch sensor
is touched with the smart key in
possession.
[ The vehicle is approached with the
smart key in possession. (if equipped)
The puddle lamp turns off if the Engine
Start/Stop button is in the ACC position
with a door open.
For more details, refer to “Welcome
System” in this chapter.
Escort light
When the Engine Start/Stop button is in
the OFF position and the driver’s door is
opened, the puddle lamp will turn on for
30 seconds. If the driver’s door is closed
within the 30 second period, the puddle
lamp will turn off after 15 seconds. If the
driver’s door is closed and locked, the
puddle lamp will turn off immediately.
The Puddle Lamp Escort Light will turn
on only the first time the driver’s door is
opened after the engine is turned off.
Welcome System
ORS051077L
Welcome system helps keep the driver
visible by turning on vehicle lights when
the driver approaches the vehicle.
Page 256 of 676
5-115
05
ORS051272
High Beam Assist will automatically
switch between high beam and low
beam depending on the detected
brightness from the lamps of oncoming
vehicles or vehicles in front.
Detecting sensor
ORS071001L
M: Front view camera
The front view camera is used as a
detecting sensor to detect ambient light
and brightness while driving.
Refer to the picture above for the
detailed location of the detecting sensor.
NOTICE
Always keep the front view camera in
good condition to maintain optimal
performance of High Beam Assist.
) R U P R U H G H W D L O V R Q W K H S U H F D X W L R Q V
of the front view camera, refer to
U ) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H $ V V L V W
) & $ V V H F W L R Q L Q F K D S W H U
High Beam Assist Setting
ORS051241L
With the Engine Start/Stop button in the
2 1 S R V L W L R Q V H O H F W S / L J K W V
Page 259 of 676
5-118
Convenience Features
ORS051284
) U R Q W : L Q G V K L H O G : L S H U V
Operates as follows when the Engine
Start/Stop button is in the ON position.
MIST: For a single wiping cycle,
push the lever upward and
release. The wipers will operate
continuously if the lever is held in
this position.
OFF: Wiper is not in operation.
AUTO: The rain sensor located on the
upper end of the windshield
glass senses the amount of
rainfall and controls the wiping
cycle for the proper interval.
The more it rains, the faster the
wiper operates. When the rain
stops, the wiper stops. To vary
the speed setting, turn the speed
control knob.
LO: The wiper runs at a lower speed.
HI: The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
the snow and/or ice is removed before
using the windshield wipers to ensure
proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO (Automatic) control
ORS051085
The rain sensor located on the upper
end of the windshield glass senses
the amount of rainfall and controls the
wiping cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
If the wiper switch is set in AUTO mode
when the Engine Start/Stop button is in
the ON position, the wiper will operate
once to perform a self-check of the
system. Set the wiper to the OFF position
when the wiper is not in use.
WIPERS AND WASHERS
Page 260 of 676
5-119
05
WARNING
To avoid personal injury from the
windshield wipers, when the engine
is running and the windshield wiper
switch is placed in the AUTO mode:
[ Do not touch the upper end of the
windshield glass facing the rain
sensor.
[ Do not wipe the upper end of the
windshield glass with a damp or wet
cloth.
[ Do not put pressure on the
windshield glass.
NOTICE
[ When washing the vehicle, set the
Z L S H U V Z L W F K L Q W K H 2 ) ) S R V L W L R Q W R
stop the auto wiper operation. The
wiper may operate and be damaged
if the switch is set in the AUTO mode
while washing the vehicle.
[ Do not remove the sensor cover
located on the upper end of the
passenger side windshield glass.
Damage to system components
could occur and may not be covered
by your vehicle warranty.
[ Because of using a photo sensor,
temporary malfunction could occur
according to sudden ambient light
change made by stone and dust
while driving.
Windshield Washers
ORG3EV051079
In the OFF position, pull the lever gently
toward you to spray washer fluid on the
windshield.
The washer fluid is sprayed as the wipers
rise while operating. The spray and wiper
operation will continue until you release
the lever.
If the lever is released, the wipers
operate approximately 4 times and the
lever returns to it's original position
Page 261 of 676
5-120
Convenience Features
Recirculating air when washer fluid
is used
When washer fluid is used, in order to
reduce any objectionable scent of the
washer fluid from entering the cabin,
recirculation mode and air conditioning
are automatically activated depending
on the outside temperature.
[ When the air intake control button is
pressed while fresh mode is selected,
air intake control will switch to
recirculation mode.
[ When windshield lever is used while
recirculation mode is selected, air
intake control will switch to fresh
mode
[ The function may not work in some
conditions such as cold weather or
engine off.
For more details, refer to “Climate
Control Additional Features” section in
this chapter.
Information
) R U * D V R O L Q H 7 * ' , 9 0 + ( 9
vehicles, outside air may enter the vehicle
even while preventing washer fluid scent
I U R P I O R Z L Q J L Q W K H F D E L Q W R F R R O W K H 9
battery.
WARNING
When the outside temperature is below
freezing, ALWAYS warm the windshield
using the defroster to help prevent
the washer fluid from freezing on the
windshield and obscuring your vision
which could result in an accident and
serious injury or death.
NOTICE
[ To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.
[ To prevent possible damage to the
wipers or windshield, do not operate
the wipers when the windshield is
dry.
[ To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
manually.
[ To prevent possible damage to the
wipers and washer system, use anti-
freezing washer fluids in the winter
season or cold weather.
