2023 GENESIS G80 belt

7-176
Driver Assistance System
How to turn off Smart function while
operating

[Press the Parking/View () button
in the following stage:
-Checking space
-Select exit direction

[Shift the gear to R (Reverse) in the
following stage:
-Checking space
-Select exit direction

[Press the Parking Safety (
) button
or select ‘Cancel’ on the infotainment
system screen to turn off Exit
function.

[While Smart Exit function is operating,
if the vehicle is stopped by depressing
the brake pedal, and the gear is
shifted, Exiting function will turn off.
At this time, EPB (Electronic Parking
Brake) will not be engaged.
The function will pause in the following
conditions when:

[There is a pedestrian, animal or object
in the direction the vehicle is moving

[The door or trunk is open

[The driver’s seat belt is not fastened

[Blind-Spot Collision-Avoidance
Assist or Rear-Cross Traffic Collision-
Avoidance Assist operates while the
vehicle is being controlled in the
reverse direction

[The Parking/View (
) button is not
continuously pressed

[The vehicle is stopped by depressing
the brake pedal
When Exit function is paused, the vehicle
will stop. If the condition that made
the function to pause disappears, the
function may operate again.
The function will cancel in the following
conditions when:

[Smart Exit
-The steering wheel is steered
-The gear is shifted while the vehicle
is moving
-Operating EPB while the vehicle is
moving
-The hood is open
-The driver opens the door with the
seatbelt unfastened
-Rapid acceleration occurs
-Vehicle skid occurs
-The wheel is stuck by an obstacle
and cannot move
-There are pedestrians, animals or
objects at the front and rear of the
vehicle at the same time
-Approximately 3 minutes and 50
seconds has passed after Smart Exit
function has started to operate
-The slope of the road exceeds the
operational range
-The function was paused for more
than 1 minute
-The steering wheel, gearshift,
braking, and drive controls are not
working properly
-ABS, TCS or ESC system operates
due to slippery road conditions
-The charging door is open
-The vehicle is utility mode
When Smart Exit function is canceled,
the vehicle will automatically stop, shift
the gear to P (Park) and engage EPB
(Electronic Parking Brake).

9-6
Maintenance
Owner Maintenance Schedule
When you stop for charging:

[Check the coolant level in the coolant
reservoir.

[Check the windshield washer fluid
level.

[Check for low or under-inflated tires.
WARNING
Be careful when checking your coolant
level if the motor compartment is hot.
This may result in coolant being blown
out of the opening and cause serious
burns and other injuries.
While operating your vehicle:

[Check for vibrations in the steering
wheel. Notice if there is any increased
steering effort or looseness in the
steering wheel, or change in its
straight-ahead position.

[Notice if your vehicle constantly turns
slightly or “pulls” to one side when
traveling on smooth, level road.

[When stopping, listen and check for
unusual sounds, pulling to one side,
increased brake pedal travel or “hard-
to-push” brake pedal.

[Check the shift gear P (Park) function.

[Check the parking brake.

[Check for fluid leaks under your
vehicle (water dripping from the air
conditioning system during or after
use is normal).
At least monthly:

[Check coolant level in the coolant
reservoir.

[Check the operation of all exterior
lights, including the stoplights, turn
signals and hazard warning flashers.

[Check the inflation pressures of all
tires including the spare for tires that
are worn, show uneven wear, or are
damaged.

[Check for loose wheel lug nuts.
At least twice a year: (for example,
every Spring and Autumn)

[Check radiator, heater and air
conditioning hoses for leaks or
damage.

[Check windshield washer spray and
wiper operation. Clean wiper blades
with a clean cloth dampened with
washer fluid.

[Check headlamp alignment.

[Check the seat belts for wear and
function.
At least once a year:

[Clean body and door drain holes.

[Lubricate door hinges and hood
hinges.

[Lubricate door and hood locks and
latches.

[Lubricate door rubber weather strips.

[Check the air conditioning system.

[Inspect and lubricate shift gear
linkage and controls.

[Clean the battery (12V) and terminals.

[Check the brake fluid level.

9-30
Maintenance
4. Genesis exclusive tire
Genesis Branded Vehicle
recommends that tires designed
specifically for Genesis vehicles
be used. You may find the marking
“GOE” (Genesis Original Equipment)
embossed on the tire sidewall.
5. Tire ply composition and material
The number of layers or plies of
rubber-coated fabric in the tire. Tire
manufacturers also must indicate the
materials in the tire, which include
steel, nylon, polyester, and others.
The letter “R” means radial ply
construction; the letter “D“ means
diagonal or bias ply construction;
and the letter “B” means belted-bias
ply construction.
6. Maximum permissible inflation
pressure
This number is the greatest amount
of air pressure that should be put in
the tire. Do not exceed the maximum
permissible inflation pressure. Refer
to the Tire and Loading Information
label for recommended inflation
pressure.
7. Maximum load rating
This number indicates the maximum
load in kilograms and pounds that
can be carried by the tire. When
replacing the tires on the vehicle,
always use a tire that has the same
load rating as the factory installed
tire.8. Uniform tire quality grading
Quality grades can be found where
applicable on the tire sidewall
between tread shoulder and
maximum section width.
For example:
TREADWEAR 200
TRACTION AA
TEMPERATURE A
Tread wear
The tread wear grade is a
comparative rating based on the
wear rate of the tire when tested
under controlled conditions on a
specified government test course.
For example, a tire graded 150 would
wear one-and-a-half times (1½) as
well on the government course as a
tire graded 100.
The relative performance of tires
depends upon the actual conditions
of their use, however, and may
depart significantly from the norm
due to variations in driving habits,
service practices and differences in
road characteristics and climate.
These grades are molded on the
sidewalls of passenger vehicle tires.
The tires available as standard or
optional equipment on your vehicle
may vary with respect to grade.
Traction - AA, A, B & C
The traction grades, from highest
to lowest, are AA, A, B and C. Those
grades represent the tire’s ability to
stop on wet pavement as measured
under controlled conditions on
specified government test surfaces
of asphalt and concrete. A tire
marked C may have poor traction
performance.

9-31
09
WARNING
The traction grade assigned to
this tire is based on straight ahead
braking traction tests, and does not
include acceleration, cornering,
hydroplaning, or peak traction
characteristics.
Temperature - A, B & C
The temperature grades are A (the
highest), B and C representing the
tire’s resistance to the generation
of heat and its ability to dissipate
heat when tested under controlled
conditions on a specified indoor
laboratory test wheel.
Sustained high temperature can
cause the material of the tire to
degenerate and reduce tire life,
and excessive temperature can
lead to sudden tire failure. Grades
B and A represent higher levels of
performance on the laboratory test
wheel than the minimum required
by law.
WARNING
The temperature grade for this
tire is established for a tire that
is properly inflated and not
overloaded. Excessive speed,
under-inflation, over-inflation, or
excessive loading, either separately
or in combination, can cause heat
build-up and possible sudden
tire failure. This may cause loss
of vehicle control resulting in an
accident.
Tire Terminology and Definitions
Air pressure
The amount of air inside the tire
pressing outward on the tire. Air
pressure is expressed in pounds per
square inch (psi) or kilopascal (kPa).
Accessory weight
This means the combined weight
of optional accessories. Some
examples of optional accessories
are automatic transmission, power
seats, and air conditioning.
Aspect ratio
The relationship of a tire’s height to
its width.
Belt
A rubber coated layer of cords that
is located between the plies and the
tread. Cords may be made from steel
or other reinforcing materials.
Bead
The tire bead contains steel wires
wrapped by steel cords that hold the
tire onto the rim.

9-35
09
All Season Tires
Genesis Branded Vehicle specifies
all season tires on some models to
provide good performance for use
all year round, including snowy and
icy road conditions. All season tires
are identified by ALL SEASON and/
or M+S (Mud and Snow) on the tire
sidewall. Snow tires have better
snow traction than all season tires
and may be more appropriate in
some areas.
Summer Tires
Genesis Branded Vehicle specifies
summer tires on some models to
provide superior performance on dry
roads. Summer tire performance is
substantially reduced in snow and
ice. Summer tires do not have the
tire traction rating M+S (Mud and
Snow) on the tire side wall. If you
plan to operate your vehicle in snowy
or icy conditions, Genesis Branded
Vehicle recommends the use of
snow tires or all season tires on all
four wheels.
Snow Tires
If you equip your car with snow
tires, they should be the same size
and have the same load capacity as
the original tires. Snow tires should
be installed on all four wheels;
otherwise, poor handling may result.
Snow tires should carry 4 psi (28 kPa)
more air pressure than the pressure
recommended for the standard
tires on the tire label on the driver’s
side of the center pillar, or up to the
maximum pressure shown on the tire
sidewall, whichever is less. Do not
drive faster than 75 mph (120 km/h)
when your vehicle is equipped with
snow tires.
Radial-Ply Tires
Radial-ply tires provide improved
tread life, road hazard resistance
and smoother high speed ride. The
radial-ply tires used on this vehicle
are of belted construction, and are
selected to complement the ride
and handling characteristics of
your vehicle. Radial-ply tires have
the same load carrying capacity,
as bias-ply or bias belted tires of
the same size, and use the same
recommended inflation pressure.
Mixing of radial-ply tires with
bias-ply or bias belted tires is not
recommended. Any combinations of
radial-ply and bias-ply or bias belted
tires when used on the same vehicle
will seriously deteriorate vehicle
handling. The best rule to follow
is: Identical pairs of radial-ply tires
should always be used as a set for
the front tires and a set for the rear
tires.
Longer wearing tires can be more
susceptible to irregular tread wear.
It is very important to follow the tire
rotation interval in this chapter to
achieve the tread life potential of
these tires. Cuts and punctures in
radial-ply tires are repairable only in
the tread area, because of sidewall
flexing. Consult your tire dealer for
radial-ply tire repairs.
WARNING
Do not mix bias ply and radial ply
tires under any circumstances.
This may cause unusual handling
characteristics that may cause loss
of vehicle control resulting in an
accident.

9-41
09
Instrument panel fuse panel
Fuse NameFuse Rating Circuit Protected
Module 910AOverhead Console, AMP, A/V & Navigation Head Unit,
Driver/Passenger Power Seat Module, Inverter (Rear),
Rear Seat LH/RH Heater Unit, Electro Chromic Mirror,
Rear Seat Console Remote Control Switch, SDC,
Smart Phone Wireless Charger, Data Link Connector
Module 1110AHead Lamp LH/RH, ADAS Unit (Parking),
Multifunction Switch
Module1210A IAU, IBU
A/C310AA/C Control Module, Front A/C Controller,
Rear A/C Controller
A/BAG IND.10A Instrument Cluster, Overhead Console
E-Shifter210A Electronic ATM Shift Dial
Spare15A Not Used
Module 1010A ICU Junction Block (ESU)
Module 710ADriver Door Module, Stop Lamp Switch, IBU, IAU,
Multifunction Switch
Multi Media25A A/V & Navigation Head Unit
Module 1310AICU Junction Block (ESU), A/C Control Module,
Front A/C Controller, Rear A/C Controller,
Instrument Cluster, Head-Up Display, Security Indicator
Cluster10A Instrument Cluster, Head-Up Display
IBU 210A IBU
Airbag 215ASRS Control Module, Passenger Occupant Detection
Sensor
Presafety Seat
Belt 310A Pre-Active Seat Belt Unit
Module810ARear Corner Radar LH/RH, ECS Unit, Crash Pad Switch,
ADAS Unit (Driving), ADAS Unit (Parking), Front View
Camera, Front Console Switch, Steering Tilt & Telescopic
Unit
Spare10A Not Used
Module310ARear Corner Radar LH/RH, Front Console Keyboard,
Rear Seat Console Remote Control Switch, VESS Unit,
Steering Tilt & Telescopic Unit, Front Corner Radar LH/RH,
Smart Phone Wireless Charger, Clock Spring

9-47
09
Rear junction block
Fuse Name Fuse Rating Circuit Protected
B+4 50AICU Junction Block (Fuse(P/Seat PASS 2, Module 4,
Door Lock, Trunk Open))
B+2 30AICU Junction Block (Fuse(IBU 1, E-Shifter 1, Spare (B+),
Module 2, Module 5,
Airbag 1), IPS2, IPS5, IPS6)
B+1 50AICU Junction Block (Fuse(Brake Switch), IPS1, IPS3,
IPS4, IPS7,
Long/Short Term Load Latch Relay)
B+3 50AICU Junction Block (Fuse(P/Seat, Curtain, P/Window
LH, S/Heater DRV,
S/Heater PASS, P/Seat DRV 1, P/Seat DRV 2, P/Seat
PASS 1, Power Handle))
Charger 15A Charging Connector Lock/Unlock Relay
P/Window RH 30ARear Power Window Module RH, Passenger Power
Window Module
AMP 25A AMP
P/Door RL 15A Rear Door Latch LH
Solar Charger 2 15A SDC
P/Door PASS 15A Passenger Door Latch
Solar Charger 1 20A SDC
Presafety Seat
Belt 130A Pre-Active Seat Belt Unit
P/Door RR 15A Rear Door Latch RH
ECS 15A ECS Unit
P/Door DRV 15A Driver Door Latch
Presafety Seat
Belt 230A Pre-Active Seat Belt Unit
Child Lock 15A Child Lock/Unlock Relay
Inverter 2 10A Inverter (Rear)
S/Heater Rear LH 20A Rear Seat LH Heater Unit
Power Trunk 30A PTL Unit (Power Trunk Lid)
S/Heater Rear RH 20A Rear Seat RH Heater Unit

9-48
Maintenance
Battery Junction Block
Fuse Name Fuse Rating Circuit Protected
B+8 100ARear Junction Block (Fuse(B+2, B+4, Solar Charger 1,
P/Door Rear LH, P/Door Rear RH, Presafety Seat Belt 2))
B+7 100ARear Junction Block (Fuse(B+3, S/Heater Rear LH, Child
Lock, S/Heater Rear RH, Power Trunk, P/Door DRV, P/Door
PASS))
B+6 100ARear Junction Block (Fuse(B+1, AMP, P/Window RH, ECS,
Presafety Seat Belt 1, Charger))
AMS 10A 12V Battery Sensor