2023 GENESIS G80 warning lights
[x] Cancel search: warning lightsPage 331 of 661
6-5
06
Start/Stop Button Positions
Button
PositionAction Notes
OFFTo turn off the vehicle, press the Start/
Stop button with the vehicle shifted to
P (Park).
Note if the Start/Stop button is
pressed with the vehicle shifted to
D (Drive), R (Reverse) or N (Neutral),
the gear will automatically shift to P
(Park).
If the Start/Stop button is pressed
with the gear shifted to N (Neutral),
the Start/Stop button will change to
the ACC position.
ACCPress the Start/Stop button when the
button is in the OFF position without
depressing the brake pedal.
Some of the electrical accessories are
usable.
The steering wheel unlocks.[ If you leave the Start/Stop button in
the ACC position for more than one
hour, the battery power will turn off
automatically to prevent the battery
from discharging.
[ If the steering wheel doesn’t unlock
properly, the Start/Stop button
will not work. Press the Start/Stop
button while turning the steering
wheel right and left to release.
ONPress the Start/Stop button while
it is in the ACC position without
depressing the brake pedal.
The warning lights can be checked
before the vehicle is started.Do not leave the Start/Stop button
in the ON position when the vehicle
is not running to prevent the battery
from discharging.
STARTTo start the vehicle, depress the brake
pedal and press the Start/ Stop button
with the gear shifted to the P (Park)
position.
For your safety, start the vehicle
with the gear shifted to the P (Park)
position.If you press the Start/Stop button
without depressing the brake pedal,
the vehicle does not start and the
Start/Stop button changes as follows:
2 ) )
Page 365 of 661
6-39
06
WARNING
Never drive too fast for the road
conditions when cornering. ESC will not
prevent accidents.
Excessive speed in turns, abrupt
maneuvers, and hydroplaning on wet
surfaces can result in severe accidents.
ESC operation
ESC ON condition
When the Start/Stop button is in the ON
position, ESC and the ESC OFF indicator
lights illuminate for approximately three
seconds. After both lights go off, ESC is
enabled.
When operating
When ESC is in operation, the
ESC indicator light blinks:
[ When you apply your brakes under
conditions which may lock the wheels,
you may hear sounds from the brakes,
or feel a corresponding sensation in
the brake pedal. This is normal and it
means your ESC is active.
[ When ESC activates, the vehicle may
not respond to the accelerator as it
does under routine conditions.
[ If Smart Cruise Control was in use
when ESC activates, Smart Cruise
Control automatically disengages.
Smart Cruise Control can be
reengaged when the road conditions
allow. See “Smart Cruise Control
(SCC)” section in chapter 7 (if
equipped).
ESC OFF condition
To cancel ESC operation:
[ State 1
Press the ESC OFF button briefly.
The ESC OFF indicator light and/or
message 'Traction Control disabled'
will illuminate. In this state, the traction
control function of ESC (electric vehicle
control management) is disabled, but the
brake control function of ESC (braking
management) still operates.
[ State 2
Press and hold the ESC OFF button
continuously for more than 3 seconds.
The ESC OFF indicator light and/or
message 'Traction & Stability Control
disabled' illuminates and a warning
chime sounds. In this state, both the
traction control function of ESC (electric
vehicle control management) and the
brake control function of ESC (braking
management) are disabled.
If the Start/Stop button is pressed to
the OFF position when ESC is off, ESC
remains off. Upon restarting the vehicle,
ESC will automatically turn on again.
When ESC (electric vehicle control) is
deactivated, the vehicle will loose the
traction and stability if the vehicle is
driven by abrupt steering wheel control.
It is possible that the tire may make a
collision with the connected parts of the
tire. We recommend to do not turn off
ESC while driving the vehicle for your
safety.
Page 366 of 661
6-40
Driving Your Vehicle
Indicator lights
v
ESC indicator light (blinks)
v
ESC OFF indicator light (comes on)
When the Start/Stop button is pressed
to the ON position, the ESC indicator
light illuminates, then goes off if the ESC
system is operating normally.
The ESC indicator light blinks whenever
ESC is operating.
If the ESC indicator light stays on, your
vehicle may have a malfunction with
the ESC system. When this warning light
illuminates , have the vehicle checked by
an authorized retailer of Genesis Branded
products as soon as possible.
The ESC OFF indicator light comes on
when ESC is turned off.
WARNING
When ESC is blinking, this indicates ESC
is active:
Drive slowly and NEVER attempt to
accelerate. NEVER turn ESC off while
the ESC indicator light is blinking or you
may lose control of the vehicle resulting
in an accident.
NOTICE
Driving with wheels and tires with
different sizes may cause the ESC
system to malfunction. Before replacing
tires, make sure all four tires and wheels
are the same size. Never drive the
vehicle with different sized wheels and
tires installed.
ESC OFF usage
When Driving
The ESC OFF mode should only be used
briefly to help free the vehicle if stuck in
snow or mud, by temporarily stopping
operation of ESC, to maintain wheel
torque.
To turn ESC off while driving, press the
ESC OFF button while driving on a flat
road surface.
NOTICE
To prevent damage to the shift by wire:
[ Do not allow wheel(s) of one axle to
spin excessively while the ESC, ABS,
and Parking Brake warning lights
are displayed. The repairs would not
be covered by the vehicle warranty.
Reduce motor power and do not spin
the wheel(s) excessively while these
lights are displayed.
[ When operating the vehicle
on a dynamometer, make sure
ESC is turned off (ESC OFF light
illuminated).
Page 409 of 661
7-17
07
& $ 8 7 , 2 1
[ Depending on the condition of the
Y H K L F O H S H G H V W U L D Q D Q G F \ F O L V W L Q
I U R Q W D Q G W K H V X U U R X Q G L Q J V W K H
speed range to operate Forward
& R O O L V L R Q $ Y R L G D Q F H $ V V L V W P D \
U H G X F H ) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H
$ V V L V W P D \ R Q O \ Z D U Q W K H G U L Y H U R U L W
P D \ Q R W R S H U D W H
[ ) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H $ V V L V W
will operate under certain conditions
E \ M X G J L Q J W K H U L V N O H Y H O E D V H G R Q
the condition of the oncoming
Y H K L F O H G U L Y L Q J G L U H F W L R Q V S H H G D Q G
V X U U R X Q G L Q J V
[ When a collision with a surrounding
Y H K L F O H L V H [ S H F W H G / D Q H & K D Q J H
2 Q F R P L Q J / D Q H & K D Q J H 6 L G H D Q G
( Y D V L Y H 6 W H H U L Q J $ V V L V W I X Q F W L R Q V Z L O O
R Q O \ Z D U Q W K H G U L Y H U L I H T X L S S H G
Information
In a situation where collision is imminent,
braking may be assisted by Forward
Collision-Avoidance Assist when braking
is insufficient by the driver.
) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H
Assist Malfunction and
Limitations
Forward Collision-Avoidance Assist
malfunction
OTM070094N
When Forward Collision-Avoidance
Assist is not working properly, the ‘Check
Forward Safety system’ warning message
will appear, and the
and warning
lights will illuminate on the cluster. Have
the vehicle inspected by an authorized
retailer of Genesis Branded products.
Page 410 of 661
7-18
Driver Assistance System
Forward Collision-Avoidance Assist
disabled
OJX1079005LOJX1079212L
When the front windshield where the
front view camera is located, front radar
cover, bumper or sensor is covered with
foreign material, such as snow or rain, it
can reduce the detecting performance
and temporarily limit or disable Forward
Collision-Avoidance Assist.
If this occurs the ‘Forward Safety system
disabled. Camera obscured’ or the
‘Forward Safety system disabled. Radar
blocked’ warning message, and the
and warning lights will illuminate on
the cluster.
Forward Collision-Avoidance Assist will
operate properly when snow, rain or
foreign material is removed.
If Forward Collision-Avoidance Assist
does not operate properly after
obstruction (snow, rain, or foreign
material) is removed (including trailer,
carrier, etc., from the rear bumper), have
the vehicle inspected by an authorized
retailer of Genesis Branded products.
WARNING
[ ( Y H Q W K R X J K W K H Z D U Q L Q J P H V V D J H R U
warning light does not appear on the
F O X V W H U ) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H
$ V V L V W P D \ Q R W S U R S H U O \ R S H U D W H
[ ) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H $ V V L V W
P D \ Q R W S U R S H U O \ R S H U D W H L Q D Q D U H D
I R U H [ D P S O H R S H Q W H U U D L Q Z K H U H
D Q \ R E M H F W V D U H Q R W G H W H F W H G D I W H U
W X U Q L Q J 2 1 W K H Y H K L F O H
Limitations of Forward Collision-
Avoidance Assist
Forward Collision-Avoidance Assist may
not operate properly, or it may operate
unexpectedly under the following
circumstances:
[ The detecting sensor or the
surroundings are contaminated or
damaged
[ The temperature around the front
view camera is high or low due to
surrounding environment
[ The camera lens is contaminated due
to tinted, filmed or coated windshield,
damaged glass, or sticky foreign
material (sticker, bug, etc.) on the
glass
[ Moisture is not removed or frozen on
the windshield
[ Washer fluid is continuously sprayed,
or the wiper is on
[ Driving in heavy rain or snow, or thick
fog
[ The field of view of the front view
camera is obstructed by sun glare
[ Street light or light from an oncoming
vehicle is reflected on the wet road
surface, such as a puddle on the road
[ An object is placed on the dashboard
Page 459 of 661
7-67
07
Limitations of Intelligent Speed
Limit Assist
Intelligent Speed Limit Assist may not
operate properly, or it may operate
unexpectedly under the following
circumstances:
[ The road sign is contaminated or
indistinguishable
-The road sign is difficult to see due
to bad weather, such as rain, snow,
fog, etc.
-The road sign is not clear or
damaged
-The road sign is partially obscured
by surrounding objects or shadow
-A road sign near the road you are
driving is detected
[ The road signs do not conform to the
standard
-The text or picture on the road sign
is different from the standard
-The road sign is installed between
the main line and the exit road or
between diverging roads
-There is no conditional road signs
on the road sign located on the exit
road
-A sign is attached to another vehicle
[ The distance between the vehicle and
the road signs is too far
[ The vehicle encounters illuminant
road signs
[ Intelligent Speed Limit Assist
incorrectly recognizes numbers in the
street signals or other signs as the
speed limit
[ A road sign near the road you are
driving is detected
[ Multiple signs are installed close
together
[ The minimum speed limit sign is
misrecognized
[ The minimum speed limit sign is on
the road[ The brightness changes suddenly, for
example when entering or exiting a
tunnel or passing under a bridge
[ Headlamps are not used or the
brightness of the headlamps are weak
at night or in the tunnel
[ Road signs are difficult to recognize
due to the reflection of sunlight, street
lights, or oncoming vehicles
[ The navigation information or GPS
information contain errors.
[ The driver does not follow the guide
of the navigation.
[ The driver is driving on a new road
that is not in the navigation system
yet.
[ The field of view of the front view
camera is obstructed by sun glare
[ Driving on a road that is sharply
curved or continuously curved
[ Driving through speed bumps, or
driving up and down or left to right on
steep inclines
[ The vehicle is shaking heavily
Information
For more details on the limitations of the
front view camera, refer to “Forward
Collision-Avoidance Assist (FCA)” section
in this chapter.
WARNING
[ Intelligent Speed Limit Assist is a
supplemental function that helps the
G U L Y H U W R F R P S O \ Z L W K W K H V S H H G O L P L W
R Q W K H U R D G D Q G P D \ Q R W G L V S O D \ W K H
correct speed limit or control the
G U L Y L Q J V S H H G S U R S H U O \
[ $ O Z D \ V V H W W K H Y H K L F O H V S H H G W R W K H
V S H H G O L P L W L Q \ R X U F R X Q W U \ O R F D O
D U H D
Page 469 of 661
![GENESIS G80 2023 Owners Manual 7-77
07
& $ 8 7 , 2 1
OJX1070030L[A] : Interior view camera
[ R Q R W D S S O \ D Q \ L P S D F W R Q W K H
V X U I D F H R I W K H L Q V W U X P H Q W F O X V W H U](/manual-img/46/58824/w960_58824-468.png "GENESIS G80 2023 Owners Manual 7-77
07
& $ 8 7 , 2 1
OJX1070030L[A] : Interior view camera
[ R Q R W D S S O \ D Q \ L P S D F W R Q W K H
V X U I D F H R I W K H L Q V W U X P H Q W F O X V W H U")
7-77
07
& $ 8 7 , 2 1
OJX1070030L[A] : Interior view camera
[ ' R Q R W D S S O \ D Q \ L P S D F W R Q W K H
V X U I D F H R I W K H L Q V W U X P H Q W F O X V W H U
camera or around the area of the
F D P H U D , I W K H L Q W H U L R U Y L H Z F D P H U D
L V G D P D J H G ) R U Z D U G $ W W H Q W L R Q
: D U Q L Q J P D \ Q R W Z R U N S U R S H U O \
[ ' R Q R W S O D F H D P R E L O H S K R Q H R U D Q
R E M H F W L Q I U R Q W R I W K H F D P H U D 7 K H
surface of the instrument cluster or
W K H F D P H U D P L J K W E H G D P D J H G G X H
W R D Q L P S D F W Z K L O H G U L Y L Q J
[ ' R Q R W S O D F H D Q \ W K L Q J R Q W K H F D P H U D
or in front of the camera while
G U L Y L Q J 7 K H L Q W H U L R U Y L H Z F D P H U D
P D \ Q R W R S H U D W H S U R S H U O \
[ , I D Q \ W K L Q J H O V H L V S O D F H G L Q I U R Q W
R I W K H F D P H U D ) R U Z D U G $ W W H Q W L R Q
: D U Q L Q J P D \ Q R W R S H U D W H S U R S H U O \
[ When cleaning the instrument
F O X V W H U R U F D P H U D Z L S H Z L W K D V R I W
D Q G F O H D Q F O R W K W R S U H Y H Q W G D P D J H V
on the surface of the cluster or
F D P H U D O H Q V , Q D G G L W L R Q \ R X V K R X O G
not use sharp tools near the cluster
R U F D P H U D R U X V H F K H P L F D O V W R F O H D Q
W K H F O X V W H U R U F D P H U D
[ $ O Z D \ V N H H S W K H F D P H U D D Q G D U R X Q G
W K H D U H D R I W K H L Q W H U L R U Y L H Z F D P H U D
F O H D Q D Q G G U \
[ ' R Q R W D S S O \ I R U H L J Q R E M H F W V V X F K
D V D V W L F N H U D U R X Q G W K H L Q I U D U H G / ( '
O R F D W H G Q H D U W K H F D P H U D
Information
[ Two red lights may appear on the
camera in the following conditions
when:
-The outside brightness is dim or
driving at night
-The vehicle drives inside a building,
such as a basement parking lot,
garage or tunnel
-The camera case of the instrument
cluster is partially broken
[ The 3D cluster may flicker when
adjusting to the driver's eyes or when
the instrument cluster's camera view is
blocked by the steering wheel or other
objects.
WARNING
Do not look toward the camera within
8 L Q F P I R U O R Q J H U W K D Q D P L Q X W H
Page 578 of 661
8-2
Emergency Situations
ORG3EV081001
The hazard warning flasher serves as
a warning to other drivers to exercise
extreme caution when approaching,
overtaking, or passing your vehicle.
It should be used whenever emergency
repairs are being made or when the
vehicle is stopped near the edge of a
roadway.
To turn the hazard warning flasher on
or off, press the hazard warning flasher
button with the Start/Stop button in any
position. The hazard warning flasher
button is located in the center fascia
panel. All turn signal lights will flash
simultaneously.
[ The hazard warning flasher operates
regardless of whether your vehicle is
running or not.
[ The turn signals do not work when the
hazard flasher is on.
If the Vehicle Stalls While Driving
[ Reduce your speed gradually, keeping
a straight line. Move cautiously off the
road to a safe place.
[ Turn on your hazard warning flasher.
[ Try to start the vehicle again. If your
vehicle will not start, contact an
authorized retailer of Genesis Branded
products or seek other qualified
assistance.
If the Vehicle Stalls at A
Crossroad or Crossing
If the vehicle stalls at a crossroads or
crossing, if safe to do so, shift the gear to
N (Neutral) and then push the vehicle to
a safe location.
To stay N (Neutral) while the vehicle is
off, refer to ‘To stay in N (Neutral) when
vehicle is OFF’ in chapter 6.
HAZARD WARNING FLASHER IN CASE OF AN EMERGENCY
WHILE DRIVING