2023 GENESIS G80 sensor
[x] Cancel search: sensorPage 287 of 661
5-93
05
WIPERS AND WASHERS
ORG3EV051067
Front Windshield Wipers
Operates as follows when the Start/Stop
button is in the ON position.
MIST : For a single wiping cycle,
push the lever upward (or
downward) and release.
The wipers will operate
continuously if the lever is
held in this position.
OFF : Wiper is not in operation.
AUTO : The rain sensor located on the
upper end of the windshield
glass senses the amount of
rainfall and controls the wiping
cycle for the proper interval.
The more it rains, the faster the
wiper operates. When the rain
stops, the wiper stops. To vary
the speed setting, turn the speed
control knob.
LO : The wiper runs at a lower speed.
HI : The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
W K H V Q R Z D Q G R U L F H L V U H P R Y H G E H I R U H
using the windshield wipers to ensure
proper operation.
, I \ R X G R Q R W U H P R Y H W K H V Q R Z D Q G R U L F H
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO (Automatic) control
ORG3EV051068
The rain sensor located on the upper
end of the windshield glass senses
the amount of rainfall and controls the
wiping cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
If the wiper switch is set in AUTO mode
when the Start/Stop button is in the ON
position, the wiper will operate once to
perform a self-check of the system. Set
the wiper to the OFF position when the
wiper is not in use.
Page 288 of 661
5-94
Convenience Features
WARNING
To avoid personal injury from the
windshield wipers, when the vehicle
is running and the windshield wiper
switch is placed in the AUTO mode:
[ Do not touch the upper end of the
windshield glass facing the rain
sensor.
[ Do not wipe the upper end of the
windshield glass with a damp or wet
cloth.
[ Do not put pressure on the
windshield glass.
NOTICE
[ When washing the vehicle, set the
wiper switch in the OFF position to
stop the auto wiper operation. The
wiper may operate and be damaged
if the switch is set in the AUTO mode
while washing the vehicle.
[ Do not remove the sensor cover
located on the upper end of the
passenger side windshield glass.
Damage to system components
could occur and may not be covered
by your vehicle warranty.
[ Because of using a photo sensor,
temporary malfunction could occur
according to sudden ambient light
change made by stone and dust
while driving.
Front Windshield Washers
ORG3EV051079
In the OFF position, pull the lever gently
toward you to spray washer fluid on the
windshield and to run the wipers 1-3
cycles. The spray and wiper operation
will continue until you release the lever. If
the washer does not work, you may need
to add washer fluid to the washer fluid
reservoir.
Recirculating air when washer fluid
is used
When washer fluid is used, in order to
reduce any objectionable scent of the
washer fluid from entering the cabin,
recirculation mode and air conditioning
are automatically activated depending
on the outside temperature. If you
select fresh mode while the function is
operating, the function will resume after
a certain amount of time. It may not work
in some conditions such as cold weather
or vehicle OFF.
For more details, refer to “Climate
Control Additional Features” section in
this chapter.
Page 327 of 661
6
6. Driving Your Vehicle
Before Driving ................................................................................................... 6-3Before Entering the Vehicle .........................................................................................6-3
Before Starting .............................................................................................................6-3
Start/Stop Button .............................................................................................. 6-4Start/Stop Button Positions .........................................................................................6-5
Starting the Vehicle ..................................................................................................... 6-6
Turning Off the Vehicle ................................................................................................ 6-7
Remote Start ................................................................................................................ 6-8
Reduction Gear (Rotary shifter) ....................................................................... 6-9Reduction gear Operation .......................................................................................... 6-9
LCD Display Messages (Cluster) ................................................................................ 6-14
Good Driving Practices .............................................................................................. 6-15
Regenerative Braking System ......................................................................... 6-17One Pedal Driving....................................................................................................... 6-18
Limitations .................................................................................................................. 6-18
i-Pedal ......................................................................................................................... 6-19
Limitations .................................................................................................................. 6-19
Smart Recuperation System .......................................................................... 6-20Smart Recuperation System Setting ........................................................................ 6-20
To Activate Smart Recuperation System ................................................................. 6-20
Ready to Operate ....................................................................................................... 6-22
How to Operate .......................................................................................................... 6-22
Smart Recuperation System Will Be Temporarily Cancelled When: ....................... 6-23
To Resume Smart Recuperation System .................................................................. 6-23
Vehicle-to-Vehicle Distance Recognition Sensor (Front Radar) ............................. 6-23
System Malfunction ...................................................................................................6-24
Limitations of the System ..........................................................................................6-24
Braking System ................................................................................................6-27Power-Assist Brakes ................................................................................................... 6-27
Disc Brakes Wear Indicator........................................................................................6-28
High performance brake ............................................................................................6-28
Electronic Parking Brake (EPB) ..................................................................................6-29
Auto Hold ....................................................................................................................6-34
Anti-Lock Brake System (ABS) ................................................................................... 6-37
Electronic Stability Control (ESC) ............................................................................ 6-38
Vehicle Stability Management (VSM) ....................................................................... 6-41
Hill-Start Assist Control (HAC) .................................................................................. 6-42
Good Braking Practices ............................................................................................ 6-43
Page 349 of 661
6-23
06
Smart Recuperation System Will
Be Temporarily Cancelled When:
[ Cancelled manually
Pulling and holding the right side
paddle shifter for more than 1 second.
The Smart Recuperation System turns
off temporarily and “AUTO” will be
replaced with regenerative braking
level indicator.
[ Cancelled automatically
-The vehicle is shifted to N (Neutral),
R (Reverse) or P (Park).
-Smart Cruise Control is in activation.
-The ESC (Electronic Stability
Control) or ABS is operating.
WARNING
When the Smart Recuperation System
is cancelled automatically, adjust the
vehicle speed directly by depressing the
accelerator or brake pedal according to
the road condition ahead and driving
condition.
To Resume Smart Recuperation
System
To re-activate the Smart Recuperation
System while driving, pull and hold the
right side paddle shifter for more than
1 second again. Then, AUTO for the
regenerative braking level will appear on
the cluster.
Vehicle-to-Vehicle Distance
Recognition Sensor (Front
Radar)
ORG3EV061016
[1] : Front radar
In order for the Smart Recuperation
System to operate properly, always make
sure the radar sensor cover is clean and
free of dirt, snow, and debris. Dirt, snow,
or foreign substances on the lens may
adversely affect the sensing performance
of the sensor. In this case, the system
operation may stop temporarily and not
operate normally.
Page 350 of 661
6-24
Driving Your Vehicle
CAUTION
[ Do not apply license plate frame or
foreign objects such as a bumper
sticker or a bumper guard near the
radar sensor. Doing so may adversely
affect the sensing performance of
the radar.
[ Always keep the radar sensor and
lens cover clean and free of dirt and
debris.
[ Use only a soft cloth to wash the
vehicle. Do not spray pressurized
water directly on the sensor or
sensor cover.
[ Be careful not to apply unnecessary
force on the radar sensor or sensor
cover. If the sensor is forcibly
moved out of proper alignment,
the Smart Recuperation System
may not operate correctly. In this
case, a warning message may not
be displayed. Have the vehicle
inspected by an authorized retailer of
Genesis Branded products.
[ If the front bumper becomes
damaged in the area around the
radar sensor, the Smart Recuperation
System may not operate properly.
Have the vehicle authorized retailer
of Genesis Branded products.
[ Use only genuine parts or the
equivalent specified for your vehicle
to repair or replace a damaged
sensor or sensor cover. Do not apply
paint to the sensor cover.
System Malfunction
OOSEV040521L
Check smart recuperation system
The message will appear when the
system is not functioning normally. The
system will be cancelled and the word
'AUTO' on the cluster will disappear and
instead display regenerative braking
level. Check for foreign substances on
the front radar. Remove any dirt, snow, or
foreign material that could interfere with
the radar sensors. If the system still does
not operate normally, take your vehicle
to an authorized retailer of Genesis
Branded products and have the system
checked.
Limitations of the System
The Smart Recuperation System may
not operate properly in certain situations
when the driving condition is beyond the
performance of the front radar sensor.
Driver's attention is required in such
cases when the system does not react
properly or operate unintentionally.
Page 351 of 661
6-25
06
Driving on a curved road
ORG3EV061018
When coasting on the curve, the system
may not detect the vehicle in your lane
and the regenerative braking level will
reduce automatically, making you feel
that the vehicle is accelerating.
Also, if the system suddenly recognizes
the vehicle in front, the regenerative
braking level will increase automatically,
making you feel that the vehicle is
decelerating.
The driver must maintain a safe braking
distance, and if necessary, depress the
brake pedal to reduce your driving speed
in order to maintain a safe distance.
ORG3EV061019
Your vehicle speed can be reduced due
to a vehicle in the adjacent lane.
Apply the accelerator pedal and select
the appropriate speed. Check to be sure
that the road conditions permit safe
operation of the Smart Recuperation
System.
Driving on an inclined road
ORG3EV061021
When coasting on an uphill or downhill,
the system may not detect the vehicle in
your lane and the regenerative braking
level will reduce automatically, making
you feel that the vehicle is accelerating.
Also, if the system suddenly recognizes
the vehicle in front, the regenerative
braking level will increase automatically,
making you feel that the vehicle is
decelerating.
The driver must maintain a safe braking
distance, and if necessary, depress the
brake pedal to reduce your driving speed
in order to maintain a safe distance.
Lane changing
ORG3EV061020
[ A vehicle which moves into your lane
from an adjacent lane cannot be
recognized by the sensor until it is in
the sensor's detection range.
[ The radar may not detect immediately
when a vehicle cuts in suddenly.
Always pay attention to the traffic,
road and driving conditions.
Page 352 of 661
6-26
Driving Your Vehicle
Vehicle recognition
ORG3EV061022
Some vehicles in your lane cannot be
recognized by the sensor:
-Narrow vehicles such as motorcycles or
bicycles
-Vehicles offset to one side
-Slow-moving vehicles or sudden-
decelerating vehicles
-Stopped vehicles (When the vehicle
ahead drives away, the system may not
detect a stopped vehicle.)
-Vehicles with small rear profile such as
trailers with no loads
A vehicle ahead cannot be recognized
correctly by the sensor if any of following
occurs:
-When the vehicle is pointing upwards
due to overloading in the luggage
compartment.
-While the steering wheel is operating.
-When driving to one side of the lane.
-When driving on narrow lanes or on
curves.
-Apply the brake or accelerator pedal if
necessary.
WARNING
When using the Smart Recuperation
System take the following precautions:
[ If an emergency stop is necessary,
you must apply the brakes.
[ Keep a safe distance according to
road conditions and vehicle speed. If
the vehicle to vehicle distance is too
close during a high-speed driving, a
serious collision may result.
[ Always maintain sufficient braking
distance and decelerate your vehicle
by applying the brakes if necessary.
[ The Smart Recuperation System
cannot recognize a stopped vehicle,
pedestrians or an oncoming vehicle.
Always look ahead cautiously to
prevent unexpected and sudden
situations from occurring.
[ Vehicles moving in front of you with
a frequent lane changes may cause
a delay in the system's reaction or
may cause the system to react to a
vehicle actually in an adjacent lane.
Always drive cautiously to prevent
unexpected and sudden situations
from occurring.
[ The Smart Recuperation System
may not recognize complex driving
situations so always pay attention to
driving conditions and control your
vehicle speed.
NOTICE
The Smart Recuperation System may
not operate temporarily due to:
[ Electrical interference
[ Modifying the suspension
[ Differences of tire abrasion or tire
pressure
[ Installing different type of tires
Page 396 of 661
![GENESIS G80 2023 Owners Manual 7-4
Driver Assistance System
Detecting sensor
ORG3EV071074
ORG3EV071001
ORG3EV071075[1]: Front view camera, [2]: Front radar,
[3]: Front corner radar (if equipped),
[4]: Rear corner radar
Refer to t](/manual-img/46/58824/w960_58824-395.png "GENESIS G80 2023 Owners Manual 7-4
Driver Assistance System
Detecting sensor
ORG3EV071074
ORG3EV071001
ORG3EV071075[1]: Front view camera, [2]: Front radar,
[3]: Front corner radar (if equipped),
[4]: Rear corner radar
Refer to t")
7-4
Driver Assistance System
Detecting sensor
ORG3EV071074
ORG3EV071001
ORG3EV071075[1]: Front view camera, [2]: Front radar,
[3]: Front corner radar (if equipped),
[4]: Rear corner radar
Refer to the picture above for the
detailed location of the detecting
sensors.
& $ 8 7 , 2 1
Take the following precautions to
maintain optimal performance of the
detecting sensor:
[ 1 H Y H U G L V D V V H P E O H W K H G H W H F W L Q J
V H Q V R U R U V H Q V R U D V V H P E O \ R U F D X V H
D Q \ G D P D J H W R L W
[ , I W K H G H W H F W L Q J V H Q V R U V K D Y H E H H Q
U H S O D F H G R U U H S D L U H G K D Y H W K H
Y H K L F O H L Q V S H F W H G E \ D Q D X W K R U L ] H G
U H W D L O H U R I * H Q H V L V % U D Q G H G S U R G X F W V
[ 1 H Y H U L Q V W D O O D Q \ D F F H V V R U L H V R U
V W L F N H U V R Q W K H I U R Q W Z L Q G V K L H O G R U
W L Q W W K H I U R Q W Z L Q G V K L H O G
[ 3 D \ H [ W U H P H F D X W L R Q W R N H H S W K H
I U R Q W Y L H Z F D P H U D G U \
[ 1 H Y H U S O D F H D Q \ U H I O H F W L Y H R E M H F W V
I R U H [ D P S O H Z K L W H S D S H U P L U U R U
R Y H U W K H G D V K E R D U G
[ ' R Q R W S O D F H D Q \ R E M H F W V Q H D U W K H
I U R Q W Z L Q G V K L H O G R U L Q V W D O O D Q \
D F F H V V R U L H V R Q W K H I U R Q W Z L Q G V K L H O G
It can affect the performance of the
defogging and defrosting function
R I W K H F O L P D W H F R Q W U R O V \ V W H P Z K L F K
P D \ S U H Y H Q W W K H ' U L Y H U $ V V L V W D Q F H
V \ V W H P V I U R P R S H U D W L Q J
[ ' R Q R W S O D F H R E M H F W V R U P R X Q W
V W U X F W X U H V Q H D U W K H Z L Q G V K L H O G
: K H Q R S H U D W L Q J W K H D L U F R Q G L W L R Q H U
moisture and defrost performance
P D \ E H S R R U D Q G G U L Y H U D V V L V W D Q F H
I X Q F W L R Q V P D \ Q R W Z R U N
[ ' R Q R W D S S O \ O L F H Q V H S O D W H I U D P H R U
R E M H F W V V X F K D V D E X P S H U V W L F N H U
I L O P R U D E X P S H U J X D U G Q H D U W K H
I U R Q W U D G D U F R Y H U
[ $ O Z D \ V N H H S W K H I U R Q W U D G D U D Q G
F R Y H U F O H D Q D Q G I U H H R I G L U W D Q G
G H E U L V
8 V H R Q O \ D V R I W F O R W K W R Z D V K W K H
Y H K L F O H ' R Q R W V S U D \ S U H V V X U L ] H G
Z D W H U G L U H F W O \ R Q W K H V H Q V R U R U
V H Q V R U F R Y H U