2023 CADILLAC CT5 parking sensors

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/10/22
Driving and Operating 339
Assist uses ultrasonic sensors
in the bumpers to measure the
distance between the vehicle
and objects. The system
calculates the distance
between vehicle and object via
measuring the time it takes for
the ultrasonic waves to
bounce back from the object.
Park Assist works only at
speeds up to about 11 Km/h
(7 mph). An illuminated LED in
the parking assist button
indicates that the system is
ready to operate. The sensors
on the bumpers may detect
objects up to 1.8m (6 ft) behind
and 1.25m (4 ft) in front of the
vehicle within a zone 25 cm
(10 in) high off the ground and
below bumper level. These
detection distances may be
shorter during warmer or
humid weather. Blocked
sensors will not detect objects
and can also cause false
detections. Keep the sensors
clean of mud, dirt, snow, ice,and slush; and clean sensors
after a car wash in freezing
temperatures.
{Warning
The Park Assist System is
no substitute for careful and
attentive driving. The Park
Assist system does not
detect children, pedestrians,
bicyclists, animals, or objects
located below the bumper or
that are too close or too far
from the vehicle. It is not
available at speeds greater
than 11 km/h (7 mph). To
prevent injury, death,
or vehicle damage, even with
Park Assist, always check
the area around the vehicle
and check all mirrors before
moving forward or backing.
How the System Works
The instrument cluster may
have a Park Assist display with
bars that show
“distance to
object,” driving direction, and
object location information for
the Park Assist system. As the
object gets closer, more bars
light up and the bars change
color from yellow to amber
to red.
Beeps sound to warn the
driver of certain objects that
are detected around the
vehicle. The frequency of
beeps increases as the vehicle
gets closer to the object.
When the object is very close
to the vehicle, the beeps are
continuous. Beeps for the

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/10/22
340 Driving and Operating
front are higher pitched than
beeps for the rear. If equipped
with Safety Alert seat, both
sides of the seat will pulse
alongside the beeps.
When the System Does Not
Seem to Work Properly
The following messages may
be displayed on the DIC:
SERVICE PARKING ASSIST :
If this message occurs, check
the following conditions:
.The sensors are not clean.
Keep the vehicle's rear
bumper free of mud, dirt,
snow, ice, and slush. For
cleaning instructions, see
Exterior Care0457.
.The Park Assist sensors are
covered by frost or ice.
Frost or ice can form around
and behind the sensors and
may not always be seen; this
can occur after washing the
vehicle in cold weather. The
message may not clear until
the frost or ice has melted. If the above conditions do not
exist, take the vehicle to your
dealer to repair the system.
PARK ASSIST OFF :
If the PA
system does not activate due
to a temporary condition, the
appropriate message displays
on the DIC. PA OFF message
is displayed when disabled by
the driver. Front/Rear PA OFF
message is displayed when an
attached object is detected in
the front or rear respectively.
PA Temporarily Unavailable
message is displayed for
system failures. This can occur
under the following conditions:
.The driver has disabled the
system.
.An object was hanging out
of the trunk during the last
drive cycle. Once the object
is removed, RPA will return
to normal operation.
.The bumper is damaged.
Take the vehicle to your
dealer to repair the system.
.Other conditions, such as
vibrations from a
jackhammer or the
compression of air brakes on
a very large truck, are
affecting system
performance.
Turning the Feature On
or Off
TouchXon the center stack
to turn on or off the Front and
Rear Park Assist, Reverse
Automatic Braking (RAB), and
the Backing Warning System
at the same time. The
indicator light next to the
button comes on when the
features are on and turns off
when the features have been
disabled.
Turn off Park Assist when
towing a trailer.
To view available settings for
this feature, touch the
Settings icon on the
infotainment home page.
Select “Vehicle” to display the

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
404 Vehicle Care
when the brake pads are worn
can still determine when the
pads should be replaced. See
Brakes0400.
To turn off the brake pad life
system: 1. Display Brake Pad Life on the DIC. See Driver
Information Center (DIC)
(Base Level) 0136 or
Driver Information Center
(DIC) (Uplevel) 0139.
2. Select the Brake Pad Life menu.
3. Select DISABLE.
To turn the brake pad life
system back on, follow the
above steps but select
ENABLE in Step 2.
Brake Pad Sensor System
(V-Series Blackwing)
The V-Series Blackwing has
electronic brake pad wear
sensors, when the brake pads
need to be replaced, a
message displays in the Driver
Information Center (DIC). When the message displays,
install new brake pads and
brake pad wear sensors on
the vehicle.
When the ignition is turned on
after new brake pads and
brake pad wear sensors are
installed, the message should
no longer display.
The brake pad sensor system
can only be reset by replacing
the brake pads and brake pad
wear sensors.
Brake Fluid
The brake/clutch master
cylinder reservoir is filled with
GM approved DOT 4 brake
fluid as indicated on the
reservoir cap. See Engine
Compartment Overview
0378
for the location of the
reservoir. Checking Brake Fluid
Place the vehicle in P (Park) or
Neutral with the parking brake
applied if equipped with a
manual transmission. On a
level surface, the brake fluid
level should be between the
minimum and maximum marks
on the brake fluid reservoir.
There are only two reasons
why the brake fluid level in the
reservoir may go down:
.Normal brake lining wear.
When new linings are
installed, the fluid level goes
back up.
.A fluid leak in the brake/
clutch hydraulic system.
Have the brake/clutch
hydraulic system fixed. With
a leak, the brakes will not
work well.
Always clean the brake fluid
reservoir cap and the area
around the cap before
removing it.

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
Vehicle Care 433
tire pressure warning light
flashes for about one minute
and then stays on for the
remainder of the ignition cycle.
A DIC warning message also
displays. The malfunction light
and DIC warning message
come on at each ignition cycle
until the problem is corrected.
Some of the conditions that
can cause these to come
on are:
.One of the road tires has
been replaced with the
spare tire. The spare tire
does not have a TPMS
sensor. The malfunction light
and DIC message should go
off after the road tire is
replaced and the sensor
matching process is
performed successfully. See
“TPMS Sensor Matching
Process”later in this section.
.The TPMS sensor matching
process was not done or not
completed successfully after
rotating the tires. The
malfunction light and the DIC
message should go off after successfully completing the
sensor matching process.
See "TPMS Sensor Matching
Process" later in this section.
.One or more TPMS sensors
are missing or damaged. The
malfunction light and the DIC
message should go off when
the TPMS sensors are
installed and the sensor
matching process is
performed successfully. See
your dealer for service.
.Replacement tires or wheels
do not match the original
equipment tires or wheels.
Tires and wheels other than
those recommended could
prevent the TPMS from
functioning properly. See
Buying New Tires
0437.
.Operating electronic devices
or being near facilities using
radio wave frequencies
similar to the TPMS could
cause the TPMS sensors to
malfunction. If the TPMS is not functioning
properly it cannot detect or
signal a low tire pressure
condition. See your dealer for
service if the TPMS
malfunction light and DIC
message come on and stay on.
Tire Fill Alert (If Equipped)
This feature provides visual
and audible alerts outside the
vehicle to help when inflating
an underinflated tire to the
recommended cold tire
pressure.
When the low tire pressure
warning light comes on:
1. Park the vehicle in a safe, level place.
2. Set the parking brake firmly.
3. Place the vehicle in P (Park).
4. Add air to the tire that is underinflated. The turn
signal lamp will flash.