2023 CADILLAC CT4 brake pads replacement

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
Instruments and Controls 131
economy over recent driving
history and the amount of fuel
remaining in the fuel tank.
Oil Life :Shows an estimate of
the oil's remaining useful life.
If REMAINING OIL LIFE 99% is
displayed, that means 99% of
the current oil life remains.
When the remaining oil life is
low, the CHANGE ENGINE OIL
SOON message will appear on
the display. The oil should be
changed as soon as possible.
See Engine Oil 0378. In
addition to the engine oil life
system monitoring the oil life,
additional maintenance is
recommended. See
Maintenance Schedule 0469.
The Oil Life display must be
reset after each oil change.
It will not reset itself. Do not
reset the Oil Life display
accidentally at any time other
than when the oil has just
been changed. It cannot be
reset accurately until the next
oil change. See Engine Oil Life
System 0381. Air Filter Life :
If equipped,
Shows an estimate of the
engine air filter’s remaining
useful life and the state of the
system. Engine Air Filter Life
95% means 95% of the
current air filter life remains.
Messages will display based
on the engine air filter life and
the state of the system. When
the REPLACE AT NEXT OIL
CHANGE message displays,
the engine air filter should be
replaced at the time of the
next oil change. When the
REPLACE SOON message
displays, the engine air filter
should be replaced at the
earliest convenience.
The Air Filter Life display must
be reset after the engine air
filter replacement. To reset,
see Engine Air Filter Life
System 0383.
Brake Pad Life : If equipped,
This displays an estimate of
the remaining life of the front
and rear brake pads.
Messages will display based on brake pad wear and the
state of the system. Reset the
Brake Pad Life display after
replacing the brake pads. See
Brake Pad Life System (If
Equipped)
0396.
Tire Pressure : Shows the
approximate pressures of all
four tires. Tire pressure is
displayed in either
kilopascal (kPa) or in pounds
per square inch (psi). If the
pressure is low, the value for
that tire is shown in amber.
See Tire Pressure Monitor
System 0424 and
Tire Pressure Monitor
Operation 0425.
Fuel Economy : Displays
average fuel economy, the
best fuel economy over the
selected distance, and a bar
graph showing instantaneous
fuel economy.
Average Speed : Displays the
average vehicle speed of the
vehicle in kilometers per
hour (km/h) or miles per
hour (mph). This average is

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/10/22
Driving and Operating 243
Light will come on and vehicle
speed may be limited to
100 kph (62 mph). Any time a
leak DTC is set, the vehicle
should be inspected carefully
for evidence of a leak and
should be repaired
immediately. See your dealer.
Brake Fade Warning Assist
The Brake Fade Warning
Assist system monitors the
performance of the brake
system. If the system detects
brake fade, or if the brake fluid
is near the boiling point, the
driver will be alerted.
The Brake Fade Warning
Assist system is designed for
use with the factory-installed
brake pads or GM approved
replacement pads. If the brake
pads on the vehicle need to be
replaced, use GM approved
brake pads. If this is not done,
the brake fade warning
system may not function
properly.Stage 1 :
The DIC displays a
“Reduce Braking to Avoid
Overheating” message, a
chime sounds and brake pedal
effort and travel is increased.
When the message displays,
the driver should back up
braking points and reduce
brake usage in order to reduce
brake temperature. This will
allow for continued lapping
with no speed limitations.
Stage 2 : The DIC displays a
Brakes Overheated Service
Now message, a chime
sounds, and brake pedal effort
and travel is further increased.
This code indicates that the
brake fluid temperature is
excessive and is about to boil.
The system limits vehicle
speed to 100 km/h (62 mph).
The driver should immediately
start a cool down lap if on the
track. If this message displays,
the vehicle needs to be
serviced. The brake system
needs to cool down, and
the brake fluid must be
immediately flushed with DOT 4 for street use, or to a
qualified DOT 4 race fluid for
track use. Boiled brake fluid is
compromised and must be
replaced.
Brake Burnishing
For vehicles equipped with
front Brembo brake systems:
Performance/racing brake
pads are required prior to
racing or closed track driving.
Vehicles with option code JE2
have performance brake pads.
This procedure should not be
performed on other models as
damage may result.
New brake pads must be
burnished before racing or
other competitive driving.
Caution
Performing the brake
burnish procedure on a base
brake system can result in
brake damage.

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
394 Vehicle Care
{Warning
The brake wear warning
sound means that soon the
brakes will not work well.
That could lead to a crash.
When the brake wear
warning sound is heard,
have the vehicle serviced.
Caution
Continuing to drive with
worn-out brake linings could
result in costly brake repairs.
Properly torqued wheel nuts
are necessary to help prevent
brake pulsation. When tires
are rotated, inspect brake
linings for wear and evenly
tighten wheel nuts in the
proper sequence to torque
specifications. See Capacities
and Specifications 0480.
Brake linings should be
replaced as complete
axle sets.
Brake Squeal and
Brake Dust
Some driving conditions or
climates can cause a brake
squeal when the brakes are
first applied, clearing up
following several applies. This
does not mean something is
wrong with the brakes.
Vehicles equipped with high
performance brake systems
provide superior fade
resistance, but will produce
increased brake squeal and
brake dust on the wheels and
calipers as compared to
standard brake linings. This is
normal.
To help reduce squeal, high
performance brake pads are
treated with an anti-squeal
paste that may need to be
reapplied periodically as part
of normal vehicle maintenance.
The anti-squeal paste will
dissipate over time. Also, the
use of wheel cleaners or
power washers directly on the
brake calipers may remove the anti-squeal paste from the
brake pads. It may be
necessary to reapply the
anti-squeal paste if it is
removed during cleaning.
If brake squeal is excessive,
the anti-squeal paste should
be reapplied. The anti-squeal
paste should always be
reapplied whenever the brake
pads are removed or replaced.
See your dealer for service.
Brake Pedal Travel
See your dealer if the brake
pedal does not return to
normal height, or if there is a
rapid increase in pedal travel.
This could be a sign that brake
service may be required.
Replacing Brake System
Parts
Always replace brake system
parts with new, approved
replacement parts. If this is
not done, the brakes may not
work properly. The braking
performance can change in

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
Vehicle Care 395
many ways if the wrong brake
parts are installed or if parts
are improperly installed.
The Brake Fade Warning
Assist system is designed for
use with the factory-installed
brake pads or GM approved
replacement pads. If the brake
pads on the vehicle need to be
replaced, use GM-approved
brake pads. If this is not done,
the brake fade warning
system may not function
properly.
High Performance Brake
Lining Car Wash and
Extended Parking Care
If equipped with high
performance brake
components, binding or
clunking may be noticeable
after extended parking or in
cold weather when the brakes
have been wet, such as when
driving in the rain or after a
car wash. The clunking is
normal for brakes with high
performance brake linings and
does not affect the operationof the brakes. When driving,
normal braking will allow for
the brakes to feel smooth and
the clunking to go away. If the
vehicle is washed before
overnight parking or long term
storage, drive it and apply the
brakes several times to
thoroughly dry the brakes.
Brake Rotor Wear
(V-Series Blackwing With
J57 Carbon Ceramic
Rotors)
The V-Series Blackwing with
J57 has carbon ceramic brake
rotors. The rotors should be
visually inspected whenever
the brake pads are replaced.
Carbon ceramic brake rotors
also need to be weighed
before brake pads are
replaced to confirm that the
rotor mass is greater than the
wear-out mass printed on the
rotor. The rotor can be reused
if the weight of the rotor is
above the mass limit. Carbon
ceramic brake rotors
inspection and weighing
methods can be found in the
service manual.
V-Series Blackwing Brake
Burnish Procedure for
Corrosion Cleanup
Corrosion spotting and
grooving on the brake rotor
surface may appear after the
vehicle sits for an extended
period of time, especially in
high humidity. This corrosion
may result in brake pulsation
and noise. To help restore
optimal braking performance
and reduce noise, complete
the following procedure:
Caution
Performing the brake
burnish procedure on a base
brake system can result in
brake damage.
Perform this procedure only
on dry pavement, in a safe
manner, and in compliance