Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
396 Vehicle Care
with all local and state
ordinances/laws regarding
motor vehicle operation.
Caution
The new vehicle break-in
period should be completed
before performing the brake
burnishing procedure or
damage may occur to the
powertrain/engine. See New
Vehicle Break-In0259.
Caution
Brake fade can occur during
this burnish procedure and
can cause brake pedal travel
and force to increase. This
could extend stopping
distance until the brakes are
fully burnished.
Completing the following
procedure as instructed will
not damage the brakes. The
brake pads may smoke and
produce an odor. The braking
force and pedal travel may increase. After the procedure,
the brake pads may appear
white at the rotor contact.
1. Using the G-Force Gauge in the HUD display, apply
the brakes 10 times
starting at 100 km/h
(60 mph) to 50 km/h
(30 mph) while
decelerating at 0.4g.
SeeHead-Up Display (HUD)
0136. This is a medium
brake application. Drive for
at least 0.5 km (0.3 mi)
between applying the
brakes.
2. If further cleanup of the brake discs is needed,
repeat this procedure with
0.7g applications.
As with all high performance
brake systems, some amount
of brake squeal is normal.
Brake Pad Life
System (If Equipped)
When to Change
Brake Pads
If equipped, this system
estimates the remaining life of
the front and rear brake pads.
Brake Pad Life is displayed in
the Driver Information Center
(DIC), along with a percentage
for each axle. The system
must be reset every time the
brake pads are changed.
When the system has
determined that the brake
pads need to be replaced, a
message displays, which may
include mileage remaining.
Brake pads should always be
replaced as complete
axle sets.
How to Reset the Brake
Pad Life System
The system will automatically
detect when significantly worn
brake pads are replaced.
Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
Vehicle Care 397
When the ignition is turned on
after new pads and wear
sensors are installed, a
message will display. Follow
the prompts to reset the
system.
The brake pad life system can
also be manually reset:1. Display Brake Pad Life on the DIC. See Driver
Information Center (DIC)
(Base Level) 0129 or
Driver Information Center
(DIC) (Uplevel) 0132.
2. Select the Brake Pad Life menu.
3. Select front or rear pads as appropriate.
4. Select YES on the confirmation message.
Repeat for the pads on the
other axle if they were also
replaced.How to Disable the Brake
Pad Life System
The brake pad life system can
be turned off. This may be
necessary if aftermarket brake
pads without wear sensors
are installed. When the system
is turned off, the front and
rear brake pad
life percentages will not
display. However, the built-in
wear indicators that make a
high-pitched warning sound
when the brake pads are worn
can still determine when the
pads should be replaced. See
Brakes 0393.
To turn off the brake pad life
system: 1. Display Brake Pad Life on the DIC. See Driver
Information Center (DIC)
(Base Level) 0129 or
Driver Information Center
(DIC) (Uplevel) 0132.
2. Select the Brake Pad Life menu.
3. Select DISABLE. To turn the brake pad life
system back on, follow the
above steps but select
ENABLE in Step 2.
Brake Pad Sensor System
(V-Series Blackwing)
The V-Series Blackwing has
electronic brake pad wear
sensors, when the brake pads
need to be replaced, a
message displays in the Driver
Information Center (DIC).
When the message displays,
install new brake pads and
brake pad wear sensors on
the vehicle.
When the ignition is turned on
after new brake pads and
brake pad wear sensors are
installed, the message should
no longer display.
The brake pad sensor system
can only be reset by replacing
the brake pads and brake pad
wear sensors.
Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
Vehicle Care 459
extreme dusty conditions,
sand, salt, heat, sun, snow,
and ice.
Weatherstrips
Apply weatherstrip lubricant
on weatherstrips to make
them last longer, seal better,
and not stick or squeak.
Lubricate weatherstrips at
least once a year. Hot, dry
climates may require more
frequent application. Black
marks from rubber material on
painted surfaces can be
removed by rubbing with a
clean cloth. See
Recommended Fluids and
Lubricants0474.
Tires
Use a stiff brush with tire
cleaner to clean the tires.
Caution
Using petroleum-based tire
dressing products on the
vehicle may damage the
paint finish and/or tires.
(Continued)
Caution (Continued)
When applying a tire
dressing, always wipe off
any overspray from all
painted surfaces on the
vehicle.
Wheels and Wheel Trim
Use a soft, clean cloth with
mild soap and water to clean
the wheels. After rinsing
thoroughly with clean water,
dry with a soft, clean towel.
A wax may then be applied.
Caution
Chrome wheels and chrome
wheel trim may be damaged
if the vehicle is not washed
after driving on roads that
have been sprayed with
magnesium chloride or
calcium chloride. These are
used on roads for conditions
such as dust control. Always
wash the chrome with soap
and water after exposure.
Caution
To avoid surface damage on
wheels and wheel trim, do
not use strong soaps,
chemicals, abrasive polishes,
cleaners, or brushes. Use
only GM approved cleaners.
Do not drive the vehicle
through an automatic car
wash that uses silicon
carbide tire/wheel cleaning
brushes. Damage could
occur and the repairs would
not be covered by the
vehicle warranty.
Brake System
Visually inspect brake lines
and hoses for proper hook-up,
binding, leaks, cracks, chafing,
etc. Inspect disc brake pads
for wear and rotors for
surface condition. Inspect
brake linings/shoes for wear
or cracks. Inspect all other
brake parts.
