2022 YAMAHA SUPERJET engine overheat

Care and storage
61
Throttle cable
Steering cable ball joint (handlebar end)
and steering cable inner wire (handlebar
end)
TIP:
Disconnect the steering cable (handlebar
end) from the ball joint before lubricating.
Steering cable (jet thrust nozzle end) and
ball joint
TIP:
Disconnect the steering cable from the ball
joint before lubricating.
EJU45861RustproofingECJ01361
Do not run the engine for more than 15
seconds on land without supplying water,
otherwise the engine could overheat.
Spray metallic parts of the hull and engine
with a rust inhibitor.
To rustproof the internal engine components:
(1) Remove the hood. (See page 26 for hoodremoval and installation procedures.)
(2) While loosening the clamp, remove the breather hose.
(3) Make sure that the area around the wa- tercraft is clear, and then start the engine
in a well-ventilated area.
(4) Run the engine at a fast idle.
(5) Quickly spray as much rust inhibitor as possible into the air intake duct through
the breather hose joint. Keep spraying
until the engine stalls (or a maximum of
15 seconds). WARNING! Do not pour or
spray gasoline, or any substance oth-
er than a rust inhibitor, into the air in-
take duct. Do not spray flammable
Recommended water-resistant grease:
YAMALUBE MARINE GREASE /
Ya m a h a G r e a s e A
UF4R71E0.book Page 61 Monday, May 10, 2021 1:14 PM

Trouble recovery
72
EJU34625
Emergency proceduresEJU44592Cleaning the jet intake and impellerEWJ00783
Before attempting to remove weeds or de-
bris from the jet intake or impeller area,
shut the engine off and remove the clip
from the engine shut-off switch. Severe in-
jury or death could result from coming in
contact with the rotating parts of the jet
pump.
If weeds or debris gets caught in the jet intake
or impeller, cavitation can occur, causing jet
thrust to decrease even though engine speed
rises. If this condition is allowed to continue,
the engine will overheat and may seize.
NOTICE: If weeds or debris gets caught in
the jet intake, do not operate the water-
craft above trolling speed until they have
been removed.
[ECJ00654]
If there is any sign that the jet intake or impel-
ler is clogged with weeds or debris, return to
shore and check the intake and impeller. Al- ways stop the engine before beaching the
watercraft.
(1) Place a suitable clean cloth or carpeting
underneath the watercraft to protect it
from abrasions and scratches. Turn the
watercraft on its side as shown.
NOTICE: When turning the watercraft
on its side, support the bow so that
the handlebars are not bent or dam-
aged.
[ECJ02691]
(2) Remove any weeds or debris from around the jet intake, drive shaft, impel-
UF4R71E0.book Page 72 Monday, May 10, 2021 1:14 PM

75
Index
A
After removing the watercraft from the water ..................................................... 56
B
Battery care.............................................. 58
Battery checks ......................................... 42
Battery, jumping....................................... 73
Beaching the watercraft ........................... 55
Bilge water check..................................... 42
Bilge water, draining ................................ 35
Bilge water, draining on land ................... 35
Bilge water, draining on water ................. 35
Boarding and starting in deep water........ 54
Boarding and starting in shallow water.... 53
Bow eye ................................................... 28
C
Capsized watercraft ................................. 54
Check engine warning ............................. 25
Cleaning ................................................... 60
Cleaning the watercraft ............................ 58
Communication disconnecting warning ................................................. 25
Cooling water pilot outlet ......................... 22
Cooling water pilot outlet check .............. 46
Craft Identification Number (CIN)............... 1
Cruising limitations..................................... 9
E
Emergency procedures ............................ 72
Engine break-in ........................................ 38
Engine compartment check ..................... 41
Engine oil ................................................. 33
Engine oil and oil filter .............................. 68
Engine oil level check............................... 42
Engine oil requirements ........................... 33
Engine overheat warning ......................... 25
Engine serial number ................................. 1
Engine shut-off cord (lanyard) check ....... 44
Engine shut-off switch ............................. 20
Engine stop/“L-MODE” switch ................ 20
Engine unit check..................................... 41
Enjoy your watercraft responsibly............ 15
Equipment ................................................ 26
F
Fire extinguisher check ............................ 45
Fire extinguisher holder............................ 29 Fire extinguisher holder, cover, and
band checks ......................................... 45
Flushing the cooling water passages....... 57
Fuel .......................................................... 31
Fuel level check........................................ 41
Fuel level meter ........................................ 24
Fuel level warning..................................... 24
Fuel requirements .................................... 31
Fuel system checks ................................. 41
G
Getting to know your watercraft .............. 47
Glossary, watercraft ................................. 16
H
Handlebar position, adjusting .................. 65
Hazard information................................... 13
Hood ........................................................ 26
Hood check .............................................. 46
Hull and deck check ................................ 45
I
Identification numbers ............................... 1
Indicator lights.......................................... 24
J
Jet intake and impeller, cleaning.............. 72
Jet intake checks ..................................... 45
Jet thrust nozzle angle, adjusting ............ 64
Jumper cables, connecting ...................... 73
L
Labels, important ....................................... 3
Labels, other .............................................. 7
Labels, warning .......................................... 4
Launching the watercraft ......................... 48
Learning to operate your watercraft......... 47
Leaving the watercraft.............................. 49
Limitations on who may operate the watercraft ................................................ 8
L-MODE ................................................... 23
Long-term storage ................................... 60
Lubrication ............................................... 60
M
Main components, location of ................. 17
Maintenance............................................. 63
Manufactured date label ............................ 2
Meter ........................................................ 24
Meter check ............................................. 46
UF4R71E0.book Page 75 Monday, May 10, 2021 1:14 PM