2022 VOLKSWAGEN ID.4 Change

the announcement. All other navigation an-
nouncements are giv
en with this volume set-
ting or are muted.
Navigation announcements are not
given if the Infotainment system has
been muted.
Restrictions during navigation
When the Infotainment system cannot re-
ceive any data from GPS satellites, e.g. in
a tunnel or underground car park, navigation
can still continue using the vehicle sensors.
In areas that are not or are not completely in-
cluded in the Infotainment memory, the Info-
tainment system will also try to enable route
guidance.
If navigation data is unavailable or incom-
plete, the navigation system may be unable
to determine the exact vehicle position. As
a result, the navigation may not be as exact
as usual.
Road navigation is subject to continuous
changes, e.g. new roads, road works, road
closures, changes in the road names and
house numbers. In the case of obsolete navi-
gation data, there may be errors or inaccura-
cies during navigation.
Controlling the navigation map
For optimal viewing, you can also operate the
navigation map with advanced finger move-
ments.
Moving the navigation map 239
11A012720AB

Fig. 158
Changing the wiper blade f or the rear
window.
The factory-fitted windscreen wiper blades
are coated with graphite. The graphite coat-
ing ensures that the wiper blade moves qui-
etly over the window. If the graphite coating
is damaged, the wiper will become louder.
Check the condition of the wiper blades on
a regular basis. Rubbing wiper blades should
be changed if damaged or cleaned if dirty

x
Do not use fuel, nail v arnish remover, paint
thinner or similar products to clean the
windows. Wax deposits on the windscreen and
rear window could cause the wiper
blades to rub. Remo

ve wax residue using
a special cleaning product or cleaning cloths. Exterior lighting
Introduction to the topic
Bef

ore changing a bulb, check whether a bulb
or LED light unit has failed. You can normally
change bulbs yourself. If the exterior lighting
is realised using LED technology, depending
on model and vehicle equipment, it is not
possible for you to change the LED light units
or individual LEDs yourself. If individual LEDs
fail, this may be an indication that more LEDs
are on the point of failure. In this case, have
the LED light units checked and renewed if
necessary at a qualified workshop.
It may be illegal to drive with faulty exterior
lights.
Additional bulb specifications
Some bulbs might have factory specifications
that differ from standard bulbs. The designa-
tion is inscribed on the bulb, either on the
glass part or on the base. NOTICE
Damage to the electrical system can be
caused by water entering the system if the
rubber co

ver or plastic covers on the head-
light housing are not properly mounted after
a bulb has been changed. Checklist “Information on
changing bulbs”
Please refer to and at the start of
the chapter on page 295.
Checklist 295
11A012720AB

oped. This also applies to engine oils in the
case of combustion engines. F or this reason,
service fluids and consumables should be re-
placed at a qualified workshop. Volkswagen
dealerships are kept up to date on all
changes. NOTICE
x Only use suitable service fluids f
or refilling.
Never use the wrong service fluid. Failure
to observe this warning can result in seri-
ous malfunctions and engine damage. Leaking service fluids can pollute the
en

vironment. Spilt service fluids must
be collected in suitable containers and dis-
posed of properly and in an environmentally
responsible way. Washer fluid

WARNING
Insufficient anti-freeze in the cooling sys-
tem of the v ehicle can cause the electric
drive to break down and thereby cause se-
rious injuries.
x The amount of correct coolant additive
used must be sufficient for the lowest
ambient temperature that you expect
the vehicle to be exposed to.
x Coolant can freeze at extremely cold
outside temperatures, causing the vehi-
cle to break down. Vehicle occupants
with inadequate winter clothing could
then freeze to death as the heating will
also no longer function. NOTICE
Never mix genuine coolant additives with
other coolants that ha
ve not been approved
by Volkswagen.
x If the liquid in the coolant expansion tank
is not pink (colouring results from mixing
the purple coolant additive with distilled
water) but for example brown instead of
purple, the suitable coolant has been
mixed with an unsuitable coolant additive.
The coolant must be changed as soon as
possible if this is the case. Failure to ob-
serve this warning can result in serious
malfunctions or damage to the electric
drive and cooling system. Coolant and coolant additives can pol-
lute the en

vironment. Spilt service flu-
ids must be collected and disposed of proper-
ly and with respect for the environment. Checking the coolant level
and refilling coolant
Please refer to , and on page 309
and at the start of the chapter on page
315. Fig. 179
Under the bonnet: markings on the
coolant e
xpansion tank. .
3.

Open the bonnet

The rolling circumference can change:

Changing a wheel
Introduction to the topic
You should carry out a wheel change yourself
only when the v
ehicle is parked safely, you
are familiar with the safety procedures and
have access to the correct equipment. Some
models are delivered from the factory with-
out a jack or box spanner. If this is the case,
wheels should be changed by a qualified
workshop.
The jack supplied with the vehicle is only de-
signed for changing a wheel when one vehi-
cle tyre is damaged and has to be replaced. If
both tyres on one side of the vehicle, both
tyres on one axle, or all tyres are damaged,
seek expert assistance. to the P position to reduce the risk of
unintended v

ehicle movement.
x Switch on the electronic parking brake.
x The wheel bolt tightening torque should
be checked with a correctly functioning
torque wrench immediately after chang-
ing a wheel.
x In the case of vehicles with a Tyre Pres-
sure Loss Indicator, the system must be
re-synchronised immediately after
a wheel change

x
Ne ver lift the vehicle when the electric
drive is switched on or if the vehicle is
tilted to the side or on a gradient. Changing a wheel
Please refer to at the start of the chap-
ter on page 343. Fig. 196
Wheel change: Unscrew the wheel
bolts with the wheel wrench.
Remo

ving the wheel