2022 TOYOTA RAV4 PLUG-IN HYBRID window

4667-3. Do-it-yourself maintenance
3Press or of the meter
control switches on the steering
wheel and select .
4Press or of the meter
control switches and select
“Vehicle Settings”, and then
press and hold .
5Press or of the meter
control switches and select
“TPWS”, and then press .
6Press or to select “Set-
ting Unit”.
7Press or to select the
desired unit and then press .
QRoutine tire inflation pressure
checks
The tire pressure warning system does
not replace routine tire inflation pressure
checks. Make sure to check tire inflation
pressure as part of your routine of daily
vehicle checks.
QTire inflation pressure
OIt may take a few minutes to display
the tire inflation pressure after the
power switch is turned to ON. It may
also take a few minutes to display the
tire inflation pressure after inflation
pressure has been adjusted.
OTire inflation pressure changes with
temperature. The displayed values
may also be different from the values
measured using a tire pressure
gauge.
QSituations in which the tire pres-
sure warning system may not oper-
ate properly
OIn the following cases, the tire pres-
sure warning system may not operate
properly.
• If non-genuine Toyota wheels are
used.
• A tire has been replaced with a tire
that is not an OE (Original Equipment)
tire.
• A tire has been replaced with a tire
that is not of the specified size.
• Tire chains, etc. are equipped.
• An auxiliary-supported run-flat tire is
equipped.
• If a window tint that affects the radio
wave signals is installed.
• If there is a lot of snow or ice on the
vehicle, particularly around the wheels
or wheel housings.
• If the tire inflation pressure is
extremely higher than the specified
level.
• If wheels without tire pressure warning
valves and transmitters are used.
• If the ID code on the tire pressure
warning valves and transmitters is not
registered in the tire pressure warning
computer.
OPerformance may be affected in the
following situations.
• Near a TV tower, electric power plant,
gas station, radio station, large dis-
play, airport or other facility that gen-
erates strong radio waves or electrical
noise
• When carrying a portable radio, cellu-
lar phone, cordless phone or other
wireless communication device
If tire position information is not cor-
rectly displayed due to the radio wave
conditions, the display may be cor-
rected by driving and changing the
radio wave conditions.
OWhen the vehicle is parked, the time

4847-3. Do-it-yourself maintenance
1Move the wiper blade until a
click sound can be heard and
the claw detaches, and then
remove the wiper blade from the
wiper arm.
2 Pull the wiper insert out past the
stopper on the wiper blade, and
then continue to pull until it is
completely removed.
Lightly grasp between the claws of the wiper blade to allow the wiper insert to lift up, making it easier to remove.
3 Remove the 2 metal plates from
the old wiper insert and install
them to the replacement wiper
insert.
4 Insert the wiper insert starting
from the claw at the center of
the wiper blade. Pass the wiper
insert through the 3 claws so
that it sticks out from the stop-
per, and then pass the wiper
insert through the final remain-
ing claw.
Applying a small amount of washer fluid to the wiper insert can make it easier to insert the claws into the grooves.
5 Check that the wiper blade
claws are fitted in the grooves of
the wiper insert.
If the wiper blade claws are not fitted in
the grooves of the wiper insert, grasp the wiper insert and slide it back and forth multiple times to insert the claws
into the grooves.
Lightly lift up the center of the wiper insert to make the rubber easier to
Rear window wiper

485
7
7-3. Do-it-yourself maintenance
Maintenance and care
slide.
6 When installing a wiper blade,
reverse the procedure in step 1.
After installing the wiper blade, check that the connection is locked.
QWiper blade and wiper insert han-dling
Improper handling may result in damage to the wiper blades or wiper insert. If you have any concerns about replacing the
wiper blades or wiper insert yourself, contact any authorized Toyota retailer or Toyota authorized repairer, or any reli-
able repairer.
NOTICE
QWhen lifting the windshield wip-
ers
OWhen raising the wiper arms off the windshield, lift up the driver side
first, and then lift up passenger side. When returning the wipers to their original position, return the
passenger side first.
ODo not lift a windshield wiper by the
wiper blade. Otherwise, the wiper blade may be deformed.
ODo not operate the wiper lever when the windshield wipers are lifted. Otherwise, the windshield
wipers may contact the hood, pos- sibly resulting in damage to the windshield wipers and/or hood.
QTo prevent damage
OBe careful not to damage the claws when replacing the wiper insert.
OAfter the wiper blade is removed from the wiper arm, place a cloth,
etc., between the rear window and wiper arm to prevent damage to the rear window.
OBe sure not to pull excessively on the wiper insert or deform its metal
plates.

501
8
8-1. Essential information
When trouble arises
more, or press it briefly 3 times
or more in succession.
5 Stop the vehicle in a safe place
by the road.
QIf emergency stopped
The functions of the air conditioning, etc.
may be partially limited in order to reduce the power consumption of the 12-volt battery.
 If the door can be opened, open
the door and exit the vehicle.
 If the door can not be opened,
open the window using the
power window switch and ensure
an escape route.
 If the window can be opened,
exit the vehicle through the win-
dow.
 If the door and window cannot be
opened due to the rising water,
remain calm, wait until the water
level inside the vehicle rises to
the point that the water pressure
inside of the vehicle equals the
water pressure outside of the
vehicle and then open the door
after waiting for the rising water
to enter the vehicle, and exit the
vehicle. When the outside water
level exceeds half the height of
the door, the door cannot be
opened from the inside due to
WARNING
QIf the hybrid system has to be turned off while driving
Turning the hybrid system off while driving will not cause a loss of steer-ing or braking control. However,
power assist for the steering wheel may be lost making it difficult to steer smoothly before stopping the vehicle
depending on the remaining charge in the 12-volt battery or usage condi-tions. Decelerate as much as possible
before turning off the hybrid system.
If the vehicle is sub-
merged or water on the
road is rising
This vehicle is not designed to
be able to drive on roads that
are deeply flooded with water.
Do not drive on roads where
the roads may be submerged
or the water may be rising. It is
dangerous to remain in the
vehicle, if it anticipated that the
vehicle will be flooded or set a
drift. Remain calm and follow
the following.

5028-1. Essential information
water pressure.
QWater level exceeds the floor
When the water level exceeds the floor and time has passed, the electrical equipment will get damaged, the power
windows will not operate, the engine and motor stop, and the vehicle may not be able to get moving.
QUsing an emergency escape ham-
mer*1
Laminated glass*2 is used in the wind- shield and the windows on this vehicle.
Laminated glass cannot be shattered
with an emergency hammer*1.*1: Contact any authorized Toyota
retailer or Toyota authorized repairer,
or any reliable repairer or aftermarket
accessory manufacturer for further
information about an emergency
hammer.
*2: If equipped
QHow to distinguish laminated glass
When looking from the cross-sectional
view point, laminated glass is two sheets of glass pasted together.
Laminated glass
Tempered glass
A
B
WARNING
QCaution while driving
Do not drive on roads where the
roads may be submerged or the water may be rising. Otherwise the vehicle may be damaged and cannot move,
as well as become flooded and set a drift, which may lead to death.

545
8
8-2. Steps to take in an emergency
When trouble arises
Use the mechanical key ( P.202)
in order to perform the following
operations.
1 Locks all the doors
2 Unlocks all the doors
QKey linked functions
1 Closes the windows and the pan-
oramic moon roof*1 (turn and hold)*2
2 Opens the windows and the pan-
oramic moon roof*1 (turn and hold)*2
*1: If equipped
*2: These settings must be customized
at any authorized Toyota retailer or
Toyota authorized repairer, or any
reliable repairer.
1 Ensure that the shift lever is in P
and depress the brake pedal.
2 Touch the area behind the but-
tons on the electronic key to the
power switch.
When the electronic key is detected, a buzzer sounds and the power switch
will turn to ON.
When the smart entry & start system is deactivated in customization setting,
the power switch will turn to ACC.
3 Firmly depress the brake pedal
and check that is dis-
played on the multi-information
display.
Locking and unlocking the
doors
WARNING
QWhen using the mechanical key and operating the power win-
dows or the panoramic moon roof (if equipped)
Operate the power window or the
panoramic moon roof after checking to make sure that there is no possibil-ity of any passenger having any of
their body parts caught in the window or the panoramic moon roof. Also, do not allow children to operate the
mechanical key. It is possible for chil- dren and other passengers to get caught in the power window or the
panoramic moon roof.
Starting the hybrid system

5769-2. Customization
QOutside rear view mirrors (P.245)
QPower windows and panoramic moon roof* (P.247, 250)
*: If equipped
QLights (P.288)
QAutomatic light control system (P.288)
FunctionDefault
settingCustomized
setting
Automatic folding and extend-
ing operationLinked to lock-
ing/unlocking of
the doorsOff
––OLinked to power
switch operation
FunctionDefault
settingCustomized
setting
Key linked operation (open)OffOn––O
Key linked operation (close)OffOn––O
Wireless remote control linked
operation (open)OffOn––O
Wireless remote control linked
operation (close)OffOn––O
Wireless remote control linked
operation signal (buzzer)OnOff––O
Side windows open warning
functionOnOff––O
Sliding roof open warning func-
tion OnOff––O
FunctionDefault
settingCustomized
setting
Light reminder buzzerOnOff––O
FunctionDefault
settingCustomized
setting
Light sensor sensitivityStandard–2 to 2O–O
ABC
ABC
ABC
ABC

577
9 9-2. Customization
Vehicle specifications
QRear window wiper (P.296)
QPCS (Pre-Collision System)*1 (P.311)
*1: If equipped
*2: The system is automatically enabled each time the power switch is turned to ON.
QLTA (Lane Tracing Assist)* (P.318)
*: If equipped
Time elapsed before the head-
lights turn off (Extended Head-
light Lighting)
30 seconds
60 seconds
––O90 seconds
120 seconds
FunctionDefault
settingCustomized
setting
Back door opening linked rear
window wiper stop functionOffOn––O
Washer linked rear window
wiper operationOnOff––O
Shift position linked rear window
wiper operation (P.297)Only onceOff––OContinuous
FunctionCustomized setting
PCS (Pre-Collision System)*2On, Off–O–
Adjust alert timingEarly, Middle, Late–O–
FunctionCustomized setting
Lane centering functionOn, Off–O–
Steering assist functionOn, Off–O–
Alert typeSteering wheel vibration, Buzzer–O–
Alert sensitivityHigh, Standard–O–
Vehicle sway warning functionOn, Off–O–
Vehicle sway warning sensitivityHigh, Standard, Low–O–
FunctionDefault
settingCustomized
settingABC
ABC
ABC
ABC