2022 TOYOTA GR86 parking brake

331
7
7-2. Steps to take in an emergency
When trouble arises
From the rear
Use a towing dolly under the front
wheels.
When using a flat-bed truck to
transport the vehicle, use tire strap-
ping belts. Refe r to the owner’s
manual of the flat-bed truck for the
tire strapping method.
In order to suppress vehicle move-
ment during transportation, set the
parking brake and turn the engine
switch off.
If a tow truck is not available in an
emergency, your vehicle may be
temporarily towed using cables or
chains secured to the emergency
towing eyelets. This should only be
attempted on hard surfaced roads
for at most 30 km (19 miles) at
under 30 km/h (18 mph).
A driver must be in the vehicle to
steer and operate the brakes. The
vehicle’s wheels, dr ive train, axles,
steering and brakes must be in
good condition.
For vehicles with an automatic
transmission, only the front towing
eyelets may be used.
To have your vehicle towed by
another vehicle, the towing eyelet
must be installed to your vehicle.
Install the towing eyelet using the
following procedure.
1 Take out the wheel nut wrench,
flathead screwdriver and towing
eyelet. ( P.346)
2 Remove the eyelet cover using
a flathead screwdriver.
To protect the bodywork, place a rag
between the screwdriver and the vehi-
NOTICE
■Towing with a sling-type truck
Do not tow with a sling-type truck to prevent body damage.
Using a flatbed truck
Emergency towing
Emergency towing proce-
dure

333
7
7-2. Steps to take in an emergency
When trouble arises
If the engine does not start, turn the
engine switch to ON.
9 Shift the shift lever to N and
release the parking brake.
Vehicles with an automatic transmis-
sion: When the shift lever cannot be shifted: P. 1 4 4
■Towing eyelet purpose
The towing eyelet is to be used to tow your vehicle, not to tow other vehicles.
■While towing
If the engine is not running, the power
assist for the brakes and steering will not function, making steering and brak-
ing more difficult.
■Wheel nut wrench
Wheel nut wrench is installed in trunk. ( P.346)
■Rear towing eyelet
If the towing eyelet is installed to the
rear, it can be used in an emergency to tow a vehicle lighter than your vehicle on
a normal road, using a rope.
■When towing another vehicle
For vehicles with BSD/RCTA, make sure
to turn BSD/RCTA off.
As the radar waves will be blocked by the towed vehicle, this system will not
operate properly.
■When installing a towing eyelet to
the rear
When installing a towing eyelet to the
rear, install it using the following proce-
dure.
1 Take out the wheel nut wrench,
flathead screwdriver and towing eye- let. ( P.346)
2 Remove the eyelet cover using a
flathead screwdriver.
To protect the bodywork, place a rag between the screwdriver and the vehicle
body as shown in the illustration.
3 Remove the cover from the bumper.
4 Insert the towing eyelet into the hole and tighten partially by hand.
5 Tighten down the towing eyelet
securely using a wheel nut wrench
or hard metal bar.

3367-2. Steps to take in an emergency
■Brake system warning light (warning buzzer)
■Vacuum pressure system warning light
■High coolant temperature warning light (warning buzzer)
If a warning light turns on or a war ning buzzer sounds
Calmly perform the following actions if any of the warning lights
comes on or flashes. If a light comes on or flashes, but then goes
off, this does not necessarily indicate a malfunction in the system.
However, if this continues to occur, have the vehicle inspected by
any authorized Toyota retailer or Toyota authorized repairer, or any
reliable repairer.
Actions to the warning lights or warning buzzers
Warning lightDetails/Actions
(red)
Indicates that:
 The brake fluid level is low; or
 The brake system is malfunctioning
This light also comes on when the parking brake is not released. If
the light turns off after the parki ng brake is fully released the sys-
tem is operating normally.
 Immediately stop the vehicle in a safe place and contact
any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer. Continuing to drive the
vehicle may be dangerous.
Warning lightDetails/Actions
(yellow)
Indicates a malfunction in the vacuum pressure system.
 Have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable
repairer immediately.
Warning lightDetails/Actions
Indicates that the engine coolant temperature is too high
 Immediately stop the vehicle in a safe place.
Handling method ( P.362)

345
7
7-2. Steps to take in an emergency
When trouble arises
■If “Check Owner’s Manual” is dis-
played
●If the following messages are shown,
following the instructions, accordingly. • “High Coolant Temperature” ( P.362)
• “Transmission Oil Temperature”
( P.143)
●If any of the following messages are
shown on the multi-information dis- play, it may indicate a malfunction.
Have the vehicle inspected by any
authorized Toyota retailer or Toyota authorized repairer, or any reliable
repairer immediately.
• “EyeSight OFF” • “Headlights Disabled”
• “ABS”
• “Steering System” • “Vehicle Stability Control”
• “Transmission”
• “Low Tire Pressure” • “RAB Disabled”
• “BSD/RCTA Disabled”
• “Keyless Access System Disabled” • “Auto Headlight Leveler Disabled”
• “SRH Disabled”
• “Gasoline Particulate Filter”
●If any of the following messages are
shown on the multi-information dis- play, it may indicate a malfunction.
Immediately stop the vehicle and con-
tact any authorized Toyota retailer or Toyota authorized repairer, or any reli-
able repairer.
• “Brake System” • “Check Engine”
• “SRS Airbag System”
 Stop the vehicle in a safe place
on a hard, flat surface.
 Set the parking brake.
 Shift the shift lever to P (auto-
matic transmission) or R (manual
transmission).
 Stop the engine.
 Turn on the emergency flashers.
( P.326)
 Check the degree of the tire
damage.
A tire should only be repaired with
the emergency tire puncture repair
If you have a flat tire
Your vehicle is not equipped
with a spare tire, but instead is
equipped with an emergency
tire puncture repair kit.
A puncture caused by a nail or
screw passing through the tire
tread can be repaired tempo-
rarily with the emergency tire
puncture repair kit.
WA R N I N G
■If you have a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the
wheel beyond repair. Driving with a
flat tire may cause a circumferential groove on the side wall. In such a
case, the tire may explode when
using the emergency tire puncture repair kit, resulting in death or serious
injury.
Before repairing the vehicle

3567-2. Steps to take in an emergency
interim measure to start the engine
if the engine switch is functioning
normally:
1 Set the parking brake.
2 Shift the shift lever to P (auto-
matic transmission) or N (man-
ual transmission).
3 Turn the engine switch to ACC.
4 Press and hold the engine
switch for about 15 seconds
while depressing the brake
pedal (automatic transmission)
or clutch pedal (manual trans-
mission) firmly.
Even if the engine can be started
using the above steps, the system
may be malfunctioning. Have the
vehicle inspected by any authorized
Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
If you lose your keys
New genuine mechanical keys
can be made by any authorized
Toyota retailer or Toyota
authorized repairer, or any reli-
able repairer using another
mechanical key and the key
number stamped on your key
number plate.
Keep the plate in a safe place
such as your wallet, not in the
vehicle.
NOTICE
■When an electronic key is lost
If the electronic key remains lost, the
risk of vehicle theft increases signifi- cantly. Visit any authorized Toyota
retailer or Toyota authorized repairer,
or any reliable repairer immediately with all remaining electronic keys that
were provided with your vehicle.

3647-2. Steps to take in an emergency
1Stop the engine. Set the parking
brake and shift the shift lever to
P (automatic transmission) or N
(manual transmission).
2 Remove the mud, snow or sand
from around the rear wheels.
3 Place wood, stones or some
other material under the rear
wheels to help provide traction.
4 Restart the engine.
5 Shift the shift lever to D or R
(automatic transmission) or 1 or
R (manual transmission) and
release the parking brake. Then,
while exercising caution,
depress the accelerator pedal.
■When it is difficult to free the vehi- cle
Press the switch to turn off TRC.
WA R N I N G
●If steam is seen coming from under
the hood, do not open the hood
until the steam has subsided. The engine compartment may be very
hot.
●Keep hands and clothing (espe-
cially a tie, a scarf or a muffler)
away from the fans and belts. Fail-
ure to do so may cause the hands or clothing to be caught, resulting in
serious injury.
●Do not loosen the coolant reservoir
caps while the engine and radiator
are hot. High temperature steam or coolant
could spray out.
NOTICE
■When adding engine coolant
Add coolant slowly after the engine
has cooled down sufficiently. Adding
cool coolant to a hot engine too
quickly can cause damage to the engine.
■To prevent damage to the cooling system
Observe the following precautions:
●Avoid contaminating the coolant
with foreign matter (such as sand or
dust etc.).
●Do not use any coolant additive.
If the vehicle becomes
stuck
Carry out the following proce-
dures if the tires spin or the
vehicle becomes stuck in mud,
dirt or snow:
Recovering procedure

3748-1. Specifications
*: The recommended oil grade is API GL-4. However, API GL-3 can also be used.
*1: Minimum pedal clearance when depressed with a force of 300 N (30 kgf, 67 lbf)
while the engine is running.
Carpet
Brake pedal
Pedal clearance
NOTICE
■Transmission fluid type
If oil other than “MT GEAR OIL LV 75W” is used, the following may be experi- enced:
●The overall performance and function of the transmission may be adversely affected.
●Rattling noises may occur during idling and fuel consumption may increase.
Never use different brands together.
Clutch
Pedal free play
Left-hand drive vehicles
4.3 16.4 mm (0.170.65 in.)
Right-hand drive vehicles
4.1 15.7 mm (0.160.62 in.)
Fluid typeSAE J1703 or FMVSS No.116 DOT 3
Brakes
Pedal clearance*174 mm (2.91 in.) Min.
Pedal free play0.51.5 mm (0.0200.059 in.)
Parking brake lever travel*27 - 8 clicks
Fluid typeSAE J1703 or FMVSS No.116 DOT 3 or SAE
J1704 or FMVSS No.116 DOT 4
A
C

375
8
8-1. Specifications
Vehicle specifications
*2: Parking brake lever travel when pulled up with a force of 200 N (20.4 kgf, 45.0
lbf).
17-inch tires
18-inch tires
A: Wedge base bulbs (clear)
B: Double end bulbs
Steering
Free playLess than 30 mm (1.2 in.)
Tires and wheels
Tire size215/45R17 87W
Tire inflation pressure (Recom-
mended cold tire inflation pressure)240 kPa (2.4 kgf/cm2 or bar, 35 psi)
Wheel size17  7 1/2 J
Wheel nut torque120 N•m (12.2 kgf•m, 89 ft•lbf)
Tire size215/40R18 85Y
Tire inflation pressure (Recom-
mended cold tire inflation pressure)240 kPa (2.4 kgf/cm2 or bar, 35 psi)
Wheel size18  7 1/2 J
Wheel nut torque120 N•m (12.2 kgf•m, 89 ft•lbf)
Light bulbs
Light bulbsWTy p e
ExteriorBack-up lights16A
Rear fog lights21A
Interior
Vanity lights (if equipped)2B
Interior light8A
Door courtesy lights (if equipped)5A
Trunk light3.8A