2022 TOYOTA GR86 window

1243-4. Adjusting the steering wheel and mirrors
1To select a mirror to adjust, turn
the switch.
Left
Right
2 To adjust the mirror, operate the
switch.
Left
Down
Right
Up
■Mirror angle can be adjusted when
The engine switch is in ACC or ON.
■When the mirrors are fogged up
The outside rear view mirrors can be cleared using the mirror defoggers. Turn
on the rear window defogger to turn on
the outside rear view mirror defoggers. ( P.266)
Press the switch to fold the mirrors.
Press it again to extend them to the
original position.
Outside rear view mir-
rors
The rear view mirror’s position
can be adjusted to enable suf-
ficient confirmation of the rear
view.
WA R N I N G
■Important points while driving
Observe the following precautions
while driving.
Failure to do so may result in loss of control of the vehicle and cause an
accident, resulting in death or serious
injury.
●Do not adjust the mirrors while driv-
ing.
●Do not drive with the mirrors folded.
●Both the driver and passenger side
mirrors must be extended and prop-
erly adjusted before driving.
Adjustment procedure
A
WA R N I N G
■When the mirror defoggers are
operating
Do not touch the rear view mirror sur- faces, as they ca n become very hot
and burn you.
Folding and extending the
mirrors
A
C
D

1263-5. Opening, closing the windows
3-5.Opening, closing the windows
The power windows can be opened
and closed using the switches.
Operating the switch moves the
windows as follows:
1 Closing
2 One-touch closing*
3Opening
4 One-touch opening*
*: To stop the window partway, operate
the switch in the opposite direction.
■The power windows can be oper-
ated when
The engine switch is in ON.
■Operating the power windows after
turning the engine off
The power windows can be operated for approximately 40 seconds after the
engine switch is turned to ACC or OFF.
They cannot, however, be operated once either front door is opened.
■Jam protection function
If an object becomes jammed between
the window and the body while the win- dow is closing, window movement is
stopped and the window is opened
slightly.
■Catch protection function
If an object becomes caught between the door and window while the window
is opening, window movement is
stopped.
■When the window cannot be opened or closed
When the jam protection function or
catch protection function operates unu- sually and the door window cannot be
opened or closed, perform the following
operations with the power window switch of that door.
1 Check that all of the doors are
closed.
2 Turn the engine switch to ON.
3 Press and hold the power window
switch in the one-touch opening position. After the window is fully
opened, continue pressing the
switch for approximately 1 second.
4 Pull and hold the power window switch in the one-touch closing posi-
tion. After the window is fully closed,
continue pulling the switch for approximately 1 second.
If you push the power window switch to
the opening position while the window is moving, start again from the beginning.
If the window continues to close but then
re-open slightly even after performing the above procedure correctly, have the
vehicle inspected by any authorized
Toyota dealer orrepairer, or another duly qualified and equipped professional.
■Door lock linked window operation
The power windows can be opened and
closed using the wireless remote con-
trol.* ( P.103)*: These settings must be customized at
any authorized Toyota retailer or
Toyota authorized repairer, or any reli-
able repairer.
■Customization
Some functions can be customized.
( P.377)
Power windows
Opening and closing the
power windows

127
3
3-5. Opening, closing the windows
Before driving
Press the switch down to lock the
passenger window glasses.
Use this switch to prevent children from
accidentally opening or closing a pas-
senger window.
WA R N I N G
Observe the following precautions.
Failure to do so may result in death or
serious injury.
■Closing the windows
●The driver is responsible for all the power window operations, including
the operation for the passengers. In
order to prevent accidental opera-
tion, especially by a child, do not let a child operate the power windows.
It is possible for children and other
passengers to have body parts caught in the power window. Also,
when riding with a child, it is recom-
mended to use the window lock switch. ( P.127)
●Check to make sure that all passen- gers do not have any part of their
body in a position where it could be
caught when a window is being operated.
●When using the wireless remote control or mechanical key and oper-
ating the power windows, operate
the power window after checking to make sure that there is no possibil-
ity of any passenger having any of
their body parts caught in the win- dow. Also do not let a child operate
window by the wireless remote con-
trol or mechanical key. It is possible for children and other passengers
to get caught in the power window.
●When exiting the vehicle, turn the engine switch off, carry the key and
exit the vehicle along with the child.
There may be accidental opera- tion, due to mischief, etc., that may
possibly lead to an accident.
■Jam protection function
●Never use any part of your body to
intentionally activate the jam pro- tection function.
●The jam protection function may not work if something gets jammed just
before the window is fully closed.
Be careful not to get any part of your body jammed in the window.
■Catch protection function
●Never use any part of your body or
clothing to intentionally activate the
catch protection function.
●The catch protection function may
not work if something gets caught just before the window is fully
opened. Be careful not to get any
part of your body or clothing caught in the window.
Preventing accidental opera-
tion (window lock switch)

1283-5. Opening, closing the windows

131
4
4-1. Before driving
Driving
is illuminated.
3 Shift the shift lever to N.
( P.147)
If parking on a hill, shift the shift lever to
1 or R and block the wheels as needed.
4 Press the engine switch to stop
the engine.
5 Slowly release the brake pedal.
6 Lock the door, making sure that
you have the key on your per-
son.
■Starting off on a steep uphill
Automatic transmission
1 Make sure that the parking
brake is set and shift the shift
lever to D.
2 Gently depress the accelerator
pedal.
3 Release the parking brake.
Manual transmission
1 Make sure that the parking
brake is set and shift the shift
lever to 1.
2 Lightly depress the accelerator
pedal at the same time as grad-
ually releasing the clutch pedal.
3 Release the parking brake.
■When starting off on an uphill
The hill-start assist c ontrol will activate.
( P.253)
■Driving in the rain
●Drive carefully when it is raining,
because visibility will be reduced, the windows may become fogged-up, and
the road will be slippery.
●Drive carefully when it starts to rain,
because the road surface will be
especially slippery.
●Refrain from high speeds when driv-
ing on an expressway in the rain, because there may be a layer of water
between the tires and the road sur-
face, preventing the steering and brakes from operating properly.
■Engine speed while driving (vehi-
cles with an automatic transmis-
sion)
In the following conditions, the engine
speed may become high while driving.
This is due to automatic up-shifting con- trol or down-shifting implementation to
meet driving conditions. It does not indi-
cate sudden acceleration.
●The vehicle is judged to be driving
uphill or downhill
●When the accelerator pedal is
released
●When driving on curves
●When the brake pedal is firmly
depressed
■Restraining the engine output
(Brake Override System)
When the accelerator and brake pedals
are depressed at the same time, the
engine output may be restrained.
■New vehicle break-in driving (the first 1600 km [1000 miles])
The performance and long life of your
vehicle are dependent on how you han- dle and care for your vehicle while it is
new. Follow these instructions during
the first 1600 km (1000 miles):
●Do not race the engine. And do not
allow the engine speed to exceed
4000 rpm except in an emergency.
●Do not drive at one constant engine or
vehicle speed for a long time, either fast or slow.
●Avoid starting suddenly and rapid acceleration, except in an emergency.
●Avoid hard braking, except in an emergency.
The same break-in procedures should

1344-1. Before driving
WA R N I N G
●Vehicles with an automatic trans-
mission: Be careful not to shift the
shift lever with the accelerator pedal depressed. Shifting the shift
lever to a gear other than P or N
may lead to unexpected rapid acceleration of the vehicle that may
cause an accident and result in
death or serious injury.
●Do not place items in the shift
lever's surrounding area. It may
cause incorrect operation.
●If the shift boot is pulled out during
cleaning, return it to its previous position. If the shift boot is left
pulled out, the shift lever may
become difficult to operate.
■If you hear a squealing or scrap-
ing noise (brake pad wear indica- tors)
Have the brake pads checked and
replaced by any authorized Toyota retailer or Toyota authorized repairer,
or any reliable repairer as soon as
possible. Rotor damage may result if the pads are not replaced when
needed.
It is dangerous to drive the vehicle when the wear limits of the brake
pads and/or those of the brake discs
are exceeded.
■When the vehicle is stopped
●Do not race the engine. If the vehicle is in any gear other
than P (automatic transmission) or
N, the vehicle may accelerate sud- denly and unexpectedly, causing an
accident.
●Vehicles with an automatic trans-
mission: In order to prevent acci-
dents due to the vehicle rolling away, always keep depressing the
brake pedal while the engine is run-
ning, and apply the parking brake as necessary.
●If the vehicle is stopped on an incline, in order to prevent acci-
dents caused by the vehicle rolling
forward or backward, always depress the brake pedal and
securely apply the parking brake as
needed.
●Avoid revving or racing the engine.
Running the engine at high speed while the vehicle is stopped may
cause the exhaust system to over-
heat, which could result in a fire if combustible material is nearby.
■When the vehicle is parked
●Do not leave glasses, cigarette
lighters, spray cans, or soft drink
cans in the vehicle when it is in the sun.
Doing so may result in the follow-
ing:
• Gas may leak from a cigarette
lighter or spray can, and may lead
to a fire.
• The temperature inside the vehicle
may cause the plastic lenses and plastic material of glasses to
deform or crack.
• Soft drink cans may fracture, caus-
ing the contents to spray over the
interior of the vehicle, and may also cause a short circuit in the vehicle’s
electrical components.
●Do not leave cigarette lighters in the
vehicle. If a cigarette lighter is in a
place such as the glove box or on the floor, it may be lit accidentally
when luggage is loaded or the seat
is adjusted, causing a fire.
●Do not attach adh esive discs to the
windshield or windows. Do not
place containers such as air fresh- eners on the instrument panel or
dashboard. Adhesive discs or con-
tainers may act as lenses, causing a fire in the vehicle.

135
4
4-1. Before driving
Driving
WA R N I N G
●Do not leave a door or window
open if the curved glass is coated
with a metallized film such as a sil- ver-colored one. Reflected sunlight
may cause the glass to act as a
lens, causing a fire.
●Always apply the parking brake,
shift the shift lever to P (vehicles
with an automatic transmission), stop the engine and lock the vehi-
cle.
Do not leave the vehicle unat- tended while the engine is running.
If the vehicle is parked with the shift
lever in P but the parking brake is not set, the vehicl e may start to
move, possibly leading to an acci-
dent.
●Do not touch the exhaust pipes
while the engine is running or immediately after turning the engine
off.
Doing so may cause burns.
■When taking a nap in the vehicle
Always turn the engine off. Otherwise, if you accidentally move the shift lever
or depress the accelerator pedal, this
could cause an accident or fire due to engine overheating. Additionally, if the
vehicle is parked in a poorly ventilated
area, exhaust gases may collect and enter the vehicle, leading to death or
a serious health hazard.
■When braking
●When the brakes are wet, drive
more cautiously. Braking distance increases when
the brakes are wet, and this may
cause one side of the vehicle to brake differently than the other
side. Also, the parking brake may
not securely hold the vehicle.
●If the brake booster device does not operate, do not follow other vehi-
cles closely and avoid hills or sharp
turns that require braking. In this case, braking is still possible,
but the brake pedal should be
depressed more firmly than usual. Also, the braking distance will
increase. Have your brakes fixed
immediately.
●Do not pump the brake pedal if the
engine stalls. Each push on the brake pedal uses
up the reserve for the
power-assisted brakes.
●The brake system consists of 2 indi-
vidual hydraulic systems; if one of the systems fails, the other will still
operate. In this case, the brake
pedal should be depressed more firmly than usual and the braking
distance will increase. Have your
brakes fixed immediately.
■If the vehicle becomes stuck
Do not spin the wheels excessively when any of the tires is up in the air,
or the vehicle is stuck in sand, mud,
etc. This may damage the driveline components or propel the vehicle for-
ward or backward, causing an acci-
dent.
NOTICE
■Pre-driving check
Trapping small animals in the cooling
fan and belts of the engine may result
in a malfunction. Check that no small animal enters the engine compart-
ment and under the vehicle before
starting the engine.

177
4
4-5. EyeSight
Driving
WA R N I N G
 At night or in a tunnel when there is
a vehicle in front that does not have
its taillights on
 Approaching a motorcycle, bicycle
or pedestrian at night
 Ambient light is poor in the evening
or early morning.
 A vehicle, motorcycle, bicycle or
pedestrian is outside the area illumi-
nated by the headlights.
 Strong light is coming from the
front (for example, sunlight at dawn,
sunset or headlight beams, etc.).
 The windshield has become
fogged, scratched or smeared, or
snow, dirt, dust or frost has adhered
to it, or it is otherwise affected. These
will reduce the stereo camera’s field
of view. Also, light is reflecting off the
dirt, etc.
 Fluid has not been fully wiped off
the windshield during or after washer
use.
 The target cannot be correctly rec-
ognized because the stereo camera’s
view is obstructed by water droplets
from rain or the window washer, or by
the wiper blades.
 The stereo camera’s field of view is
obstructed.
 The rear aspect of the vehicle in
front is low, small or irregular (the sys-
tem may recognize another part of the
vehicle as its rear and will determine
operation from that).
• There is an empty truck or trailer
with no rear and/or side panels on the cargo bed.
• Vehicles that have cargo protrud-ing from their back ends
• Non-standard shaped vehicles (vehicle transporters or vehicles
with a sidecar fitted, etc.)
• The height of the vehicle is low, etc.
 There is a wall, etc. in front of a
stopped vehicle.
 There is another object near the
vehicle.
 A vehicle, etc. has its side facing
you.
 With vehicles that are backing up
or with oncoming vehicles, etc.
 The size and height of an obstacle
is smaller than the limitations of the
stereo camera’s recognition capabil-
ity.
• With small animals or children, etc.
• With pedestrians who are sitting or
lying down
 The detected object is a fence or
wall, etc. with a uniform pattern (a
striped pattern or brick pattern, etc.).