2022 TOYOTA GR86 air condition

2144-5. EyeSight
*: If equipped
●The following situations may cause incorrect lane detection and a faulty
Lane Departure Warning to occur.
• There are tire tracks on a wet road or snow-covered road.
• There are boundaries between snow
and asphalt, or marks from road repair, etc.
• There are the shadows of guardrails.
• Lane markings are drawn in double. • There are some lane markings left
from roadwork or markings from the
previous road.
●When the Lane Departure Warning
OFF indicator is illuminated, Lane Departure Warning is inactive.
( P.215)
Lane Departure War n-
ing*
When vehicle speed is approxi-
mately 50 km/h (30 mph) or
more, this function warns the
driver if the system detects
that the vehicle is likely to
depart the traffic lane.
When Lane Departure Warning
activates, an alert sounds 3
short beeps and a pop-up dis-
play will be displayed.
“Lane Departure”A
WA R N I N G
Lane Departure Warning will not oper-
ate in all conditions. It also will not
automatically return the vehicle to the original lane. If the driver relies only
on Lane Departure Warning to keep
the vehicle in the lane, lane departure may occur, resulting in an accident.
Lane Departure Warning activates
when it detects lane markings. How- ever, it is not a function which can
detect the edge of a road (shoulders
or side ditches, etc.) and warn the driver.
NOTICE
In the following situations, Lane Departure Warning may not activate:
●Vehicle speed is approximately 50 km/h (30 mph) or less.
●The steering wheel is turned signifi-cantly to either side.
●The vehicle is driving around a
curve whose radius is 300 m (0.18 miles) or smaller.
●The brake pedal is depressed or immediately after it is depressed.
●The following distance behind a vehicle in front is short.
●The turn signal is operating.
●For approximately 4 seconds after
the turn signal lever has returned to its original position.
●The vehicle has not returned to the inside of the lane after Lane Depar-
ture Warning has activated.
●The lane is narrow.
●It is difficult for the camera to detect lane markings.
• There are no lane markings or they
are very worn.

2244-5. EyeSight
Warning messageCauseAction
“EyeSight Disabled No
Camera View”
It is difficult for the stereo
camera to detect objects in
front.
• The windshield is dirty or
fogged up.
• Poor weather conditions
• Strong light from the
front
 Clean the windshield.
 In poor weather condi-
tions or if there is strong
light from the front, the
EyeSight system will
restart once you have
driven your vehicle for a
period of time and the
conditions affecting the
system have improved.
If the system does not
restart, even after the
conditions have
improved and a period
of time has elapsed,
contact any authorized
Toyota retailer or Toyota
authorized repairer, or
any reliable repairer for
an inspection.

225
4
4-5. EyeSight
Driving
●When (white) is illuminated, no
EyeSight functions can be used except for Conventional Cruise Con-
trol.
●When (white) is illuminated, the
Reverse Automatic Braking (RAB)
system may not operate.
“EyeSight Disabled Temp
Range”
In low or high tempera-
tures
The system will restart
once the temperature is
within the operational
range of the EyeSight sys-
tem. If the system does
not restart, even when the
temperature inside the
vehicle is within the opera-
tional range, contact any
authorized Toyota retailer
or Toyota authorized
repairer, or any reliable
repairer for an inspection.
“EyeSight Disabled Check
Manual”
• The EyeSight system is
starting up.
• The system has deter-
mined that the vehicle is
extremely inclined.
• The Pre-Collision sec-
ondary braking has
operated 3 times after
the engine was started.
• The engine has
stopped.
The system will restart
once the cause has been
resolved. At this time, it
may take some time for
the system to restart. If the
system does not restart,
even after the conditions
have improved and a
period of time has
elapsed, contact any
authorized Toyota retailer
or Toyota authorized
repairer, or any reliable
repairer for an inspection.
Warning messageCauseAction

229
4
4-6. Using other driving systems
Driving
OFF indicator will appear.
• When the radar sensor becomes sig- nificantly misaligned (If the orientation
of the radar sensor is shifted for any
reason, readjustment is required. Have the sensor adjusted at any
authorized Toyota retailer or Toyota
authorized repairer, or any reliable repairer.)
• When a large amount of snow or ice
sticks to the rear bumper surface around the radar sensors
• When the vehicle is driven on a
snow-covered road or in an environ- ment in which there are no objects
around (such as in a desert) for a pro-
longed period of time • When the temperature around the
radar sensors increases excessively
due to long driving on uphill grades in the summer, etc.
• When the temperature around the
radar sensors becomes extremely low • When the vehicle battery voltage low-
ers
• When the vehicle voltage exceeds the battery voltage rating
●The BSD/RCTA will resume operation once these conditions are corrected,
and the BSD/RCTA OFF indicator will
disappear. However, if the BSD/RCTA OFF indicator appears for a prolonged
period of time, have the system
inspected at any authorized Toyota retailer or Toyota authorized repairer,
or any reliable repairer as soon as
possible.
●The detectability of the radar sensors
is restricted. The BSD/RCTA detec- tion may be impair ed and the system
may not operate properly under the
following conditions.
• When the rear bumper around the radar sensors is distorted
• When ice, snow or mud adheres to
the rear bumper surface around the radar sensors
• When stickers, etc. are affixed on the
areas of the radar sensors on the rear bumper
• During adverse weather conditions
such as rain, snow or fog
• When driving on wet roads such as
snow-covered roads and through pud- dles
●The radar sensors may not detect or may have difficulty detecting the fol-
lowing vehicles and objects.
• Small motorcycles, bicycles, pedestri- ans, stationary objects on the road or
road side, etc.
• Vehicles with body shapes that the radar may not reflect (vehicles with
lower body height such as a trailer
with no cargo and sports cars) • Vehicles that are not approaching
your vehicle even though they are in
the detection area (either on a neigh- boring lane to the rear or beside your
vehicle when revers ing) (The system
determines the presence of approach- ing vehicles based on data detected
by the radar sensors.)
• Vehicles traveling at significantly dif- ferent speeds
• Vehicles driving in parallel at almost
the same speed as your vehicle for a prolonged time
• Oncoming vehicles
• Vehicles in a lane beyond the neigh- boring lane
• Vehicles travelling at a significantly
lower speed that you are trying to overtake
●On a road with extremely narrow lanes, the system may detect vehicles
driving in a lane next to the neighbor-
ing lane.
While the BSD/RCTA is active, the
following item(s) will operate to
alert the driver:
 The BSD/RCTA approach indica-
tor (when there are vehicles in
the neighboring lanes).
 The BSD/RCTA approach indica-
BSD/RCTA approach indica-
tor/warning buzzer

231
4
4-6. Using other driving systems
Driving
• In low radius bends (tight bends or
when making turns at an intersection)
• When there is a difference in height
between your lane and the neighbor-
ing lane
• Immediately after the BSD/RCTA is
activated by touching “BSD/RCTA”
• Immediately after the shift lever is
shifted to R
• When extremely heavy cargo is
loaded in the trunk
 During reversing, operation of
the BSD/RCTA approach indica-
tor and the warning buzzer may
be delayed or the system may
fail to issue these warnings
under the following conditions.
• When backing out of an angled park-
ing space
• When a large-sized vehicle is parked
next to your vehicle (That vehicle pre-
vents the propagation of radar
waves.)
• When reversing on sloped roads
• When reversing at a high speed
 The BSD/RCTA approach indica-
tor may illuminate when driving
close to solid objects on the road
or road side (such as guardrails,
tunnels and sidewalls).
 When turning at an intersection
in urban areas, or a multilane
intersection, the BSD/RCTA
approach indicator may flash.
 If a building or a wall exists in the
reversing direction, the
BSD/RCTA approach indicator
may flash and the warning
buzzer may sound.
 In the following cases, the sys-
tem may detect a vehicle driving
two lanes away from your vehi-
cle.
• When your vehicle drives on the near
side of its lane from the correspond-
ing vehicle
• When the vehicle driving two lanes
away drives on the near side of its
lane from your vehicle
■System temporary stops
This display appears when the sys-
tem is used at extremely high or
low temperatures or when abnor-
mal voltage exists. Once these con-
ditions are correc ted, the system
will recover from the temporary
stop condition and the indicator will
disappear.
If the indicator remains displayed
for a prolonged time, have the sys-
tem inspected at any authorized
Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
BSD/RCTA OFF indicator

2324-6. Using other driving systems
“BSD/RCTA Disabled”
BSD/RCTA OFF indicator
■System temporary stops due
to reduced radar sensitivity
This display appears when the
detectability of the radar sensors is
reduced. Once the condition is cor-
rected, the system will recover from
the temporary stop condition and
the indicator will disappear.
If the indicator remains displayed
for a prolonged time, have the sys-
tem inspected at any authorized
Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
“BSD/RCTA Disabled Sensor
Blocked”
BSD/RCTA OFF indicator
■System malfunction
This display appears when a mal-
function occurs in the system. Con-
tact any authorized Toyota retailer
or Toyota authorized repairer, or
any reliable repairer and have the
system inspected.
“BSD/RCTA Disabled Check
Owner's Manual”
BSD/RCTA warning light
To turn the BSD/RCTA system on
and off, operate the multi-informa-
tion display ( P.377) or multimedia
system screen (Refer to “Multime-
dia owner’s manual”).
When the BSD/RCTA system is
turned OFF, the BSD/RCTA OFF
indicator on the multi-information
display will illuminate.
A
A
BSD/RCTA warning light
To turn on/off the BSD/RCTA
A

2364-6. Using other driving systems
When the vehicle is stopped by
the system (in this case, the con-
tinuous beep w ill remain sound-
ing)
“Apply Brake To Hold Position”
The Reverse Automatic Braking
(RAB) system will op erate when all
of the following conditions are met.
 The engine switch is in ON.
 The EyeSight warning light is off.
 The RAB warning light is off.
 The RAB OFF indicator is off.
 The shift lever is in the R.
EyeSight warning light
RAB warning light
RAB OFF indicator
Sonar Audible Alarm
 The Sonar Audible Alarm is set
to “ON”.
 The vehicle speed is from 0 to 15
km/h (0 to 9 mph).
Automatic Braking
 The Automatic Braking is set to
“ON”.
 The vehicle speed is from 1.5 to
15 km/h (1 to 9 mph).
●In the following cases, the Reverse
Automatic Braking (RAB) system will not operate. Promptly contact any
authorized Toyota retailer or Toyota
authorized repairer, or any reliable repairer to have the system inspected.
• The EyeSight warning light is illumi-
nated. • The RAB warning light is illuminated.
●In the following cases, the Reverse Automatic Braking (RAB) system can-
not be operated.
• The RAB OFF indicator is illuminated.
●In the following cases, the functions
may not be able to properly work.
Promptly contact any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer to
WA R N I N G
If your vehicle is trapped on a railroad crossing and you are trying to escape
by reversing through the crossing
gate, the system may recognize the crossing gate as an obstacle and
brake may activate. In this case,
remain calm and either continue to depress the accelerator pedal or can-
cel the system. ( P.241)
Operating conditions
A
A
C

237
4
4-6. Using other driving systems
Driving
have the system inspected.
• A sticker, paint, or a chemical is applied to the sonar sensors or the
rear bumper near the sonar sensor.
• The rear bumper is modified. • The rear bumper has been removed
and attached.
• The ground clearance is changed due to the vehicle’s loading condition or
modification.
• There is damage to the sonar sensors or the rear bumper near the sonar
sensor.
• The rear bumper is exposed to strong impact, or the rear bumper is
deformed.
●On a steep hill, the system’s auto-
matic braking ability will be reduced.
●The system is designed to avoid colli-
sions by automatic hard braking when
the vehicle’s reversing speed is less than approximately 5 km/h (3 mph).
However, the system does not guar-
antee that the vehicle will be able to avoid collisions in any situation.
●If the vehicle is reversed at an extremely slow speed, the driver’s
operation may be prioritized. In this
case, automatic braking will not oper- ate.
●The system may not be able to detect and apply the brake with the following
objects.
• Sharp or thin objects such as poles, fences and ropes which may not
reflect the sound wave emitted from
the sonar sensor. • Objects that are too close to the rear
bumper when the shift lever is set to
R. • Objects with a surface which may not
reflect the sound wave emitted from
the sonar sensor such as a chain link
fence.
●Objects the system is not designed to
detect and apply brake. • Pedestrians.
• Moving objects including moving vehi-
cles. • Objects which absorbs sound waves
such as cloth or snow.
• Objects whose surface has a diagonal
angle. • Objects that are low to the ground
such as parking blocks.
• Objects that are high above the ground such as objects hanging from
above.
• Objects that are out of range of the center of the vehicle in the horizontal
direction.
• Objects that are not in a vertical direc- tion.
• Objects which are not perpendicular
to the ground. • Objects which are not directly in the
traveling direction of the vehicle.
• Objects which are uneven or wavy.
●When reversing the vehicle, the func-
tions may not be able to work properly or may cause a system malfunction if
the following conditions exist.
High frequency sound from other
sources are nearby:
• Horn sound from another vehicle. • Engine sound from other vehicles.
• Sound of an air brake.
• Vehicle detection equipment or a sonar from another vehicle.
• A sound wave with a frequency similar
to the vehicle’s system is transmitted near by.
• A vehicle equipped with the same sys-
tem is reversing toward your reversing direction.
●Weather conditions:• Extremely high or extremely low tem-
peratures in which the area near the
sonar sensor becomes too hot or too cold to operate.
• The sonar sensors or the rear bumper
near the sonar sensors are exposed to heavy rain or a significant amount
of water.
• Fog, snow or sandstorm, etc.
• Air is moving rapidly such as when a strong wind is blowing.
●Parts attached to the rear bumper near the sonar sensor:
• Commercial electronic parts (fog light,
fender pole, radio antenna) or com- mercial attachment parts (trailer hitch,