2022 TOYOTA GR86 instrument panel

1123-2. Opening, closing and locking the doors and trunk
switch modes are changed.
●Do not leave the electronic key on top
of the instrument panel or near the
door pockets when exiting the vehicle. Depending on the radio wave recep-
tion conditions, it may be detected by
the antenna outside the cabin and the doors will become lockable from the
outside, possibly trapping the elec-
tronic key inside the vehicle.
●As long as the electronic key is within
the effective range, the doors may be locked or unlocked by anyone. How-
ever, only the doors detecting the
electronic key can be used to unlock the vehicle.
●Even if the electronic key is not inside the vehicle, it may be possible to start
the engine if the electronic key is near
the window.
●The doors may unlock or lock if a
large amount of water splashes on the door handle, such as in the rain or in a
car wash, when the electronic key is
within the effective range. (The doors will automatically be locked after
approximately 30 seconds if the doors
are not opened and closed.)
●If the wireless remote control is used
to lock the doors when the electronic key is near the vehicle, there is a pos-
sibility that the door may not be
unlocked by the entry function. (Use the wireless remote control to unlock
the doors.)
●Touching the door lock or unlock sen-
sor while wearing gloves may prevent
lock or unlock operation.
●Vehicles without a double locking sys-
tem: When the lock operation is per-
formed using the lock sensor, recognition signals will be shown up to
three consecutive times. After this, no
recognition signals will be given.
●If the door handle becomes wet while
the electronic key is within the effec- tive range, the door may lock and
unlock repeatedly. In this case, follow
the following correction procedures to
wash the vehicle:
• Place the electronic key in a location 2 m (6 ft.) or more away from the vehi-
cle. (Take care to ensure that the key
is not stolen.) • Set the electronic key to battery-sav-
ing mode to disable the smart entry &
start system. ( P. 1 1 1 )
●If the electronic key is inside the vehi-
cle and a door handle becomes wet during a car wash, a message may be
shown on the multi-information dis-
play and a buzzer will sound outside the vehicle. To turn off the alarm, lock
both side doors.
●The lock sensor may not work prop-
erly if it comes into contact with ice,
snow, mud, etc. Clean the lock sensor and attempt to operate it again.
●A sudden handle operation or a han-dle operation immediately after enter-
ing the effective range may prevent
the doors from being unlocked. Touch the door unlock sensor and check that
the doors are unlocked before pulling
the door handle again.
●Unlocking the vehicle may take more
time if another electronic key is within the effective range.
■When the vehicle is not driven for
extended periods
●To prevent theft of the vehicle, do not
leave the electronic key within 2 m (6
ft.) of the vehicle.
●The smart entry & start system can be
deactivated in advance. ( P. 1 1 3 )
●Setting the electronic key to bat-
tery-saving mode helps to reduce key battery depletion. ( P. 1 1 1 )
■To operate the system properly
●Make sure to carry the electronic key
when operating th e system. Do not get the electronic key too close to the
vehicle when operating the system
from the outside of the vehicle.
Depending on the position and holding
condition of the electronic key, the key may not be detected correctly and the

1344-1. Before driving
WA R N I N G
●Vehicles with an automatic trans-
mission: Be careful not to shift the
shift lever with the accelerator pedal depressed. Shifting the shift
lever to a gear other than P or N
may lead to unexpected rapid acceleration of the vehicle that may
cause an accident and result in
death or serious injury.
●Do not place items in the shift
lever's surrounding area. It may
cause incorrect operation.
●If the shift boot is pulled out during
cleaning, return it to its previous position. If the shift boot is left
pulled out, the shift lever may
become difficult to operate.
■If you hear a squealing or scrap-
ing noise (brake pad wear indica- tors)
Have the brake pads checked and
replaced by any authorized Toyota retailer or Toyota authorized repairer,
or any reliable repairer as soon as
possible. Rotor damage may result if the pads are not replaced when
needed.
It is dangerous to drive the vehicle when the wear limits of the brake
pads and/or those of the brake discs
are exceeded.
■When the vehicle is stopped
●Do not race the engine. If the vehicle is in any gear other
than P (automatic transmission) or
N, the vehicle may accelerate sud- denly and unexpectedly, causing an
accident.
●Vehicles with an automatic trans-
mission: In order to prevent acci-
dents due to the vehicle rolling away, always keep depressing the
brake pedal while the engine is run-
ning, and apply the parking brake as necessary.
●If the vehicle is stopped on an incline, in order to prevent acci-
dents caused by the vehicle rolling
forward or backward, always depress the brake pedal and
securely apply the parking brake as
needed.
●Avoid revving or racing the engine.
Running the engine at high speed while the vehicle is stopped may
cause the exhaust system to over-
heat, which could result in a fire if combustible material is nearby.
■When the vehicle is parked
●Do not leave glasses, cigarette
lighters, spray cans, or soft drink
cans in the vehicle when it is in the sun.
Doing so may result in the follow-
ing:
• Gas may leak from a cigarette
lighter or spray can, and may lead
to a fire.
• The temperature inside the vehicle
may cause the plastic lenses and plastic material of glasses to
deform or crack.
• Soft drink cans may fracture, caus-
ing the contents to spray over the
interior of the vehicle, and may also cause a short circuit in the vehicle’s
electrical components.
●Do not leave cigarette lighters in the
vehicle. If a cigarette lighter is in a
place such as the glove box or on the floor, it may be lit accidentally
when luggage is loaded or the seat
is adjusted, causing a fire.
●Do not attach adh esive discs to the
windshield or windows. Do not
place containers such as air fresh- eners on the instrument panel or
dashboard. Adhesive discs or con-
tainers may act as lenses, causing a fire in the vehicle.

1384-1. Before driving
WA R N I N G
●Do not place cargo or luggage in or
on the following locations as the
item may get under the clutch (manual transmission), brake or
accelerator pedal and prevent the
pedals from being depressed prop- erly, block the driver’s vision, or hit
the driver or passengers, causing
an accident:
• At the feet of the driver
• On the front passenger or rear
seats (when stacking items)
• On the package tray
• On the instrument panel
• On the dashboard
●Secure all items in the occupant
compartment, as they may shift and injure someone during sudden
braking, sudden swerving or an
accident.
■Load and distribution
●Do not overload your vehicle.
●Do not apply loads unevenly.
Improper loading may cause deteri- oration of steering or braking con-
trol which may cause death or
serious injury.
Trailer towing
Toyota does not recommend
towing a trailer with your vehi-
cle. Toyota also does not rec-
ommend the installation of a
tow hitch or the use of a tow
hitch carrier for a wheelchair,
scooter, bicycle, etc. Your vehi-
cle is not designed for trailer
towing or for the use of tow
hitch mounted carriers.

153
4
4-3. Operating the lights and wipers
Driving
4-3.Operating the lights and wipers
Operating the switch turns
on the lights as follows:
1 The headlights, front posi-
tion/daytime running lights
( P.153) and all the lights listed
above turn on and off automati-
cally. (When the engine switch is
in ON.)
2 The front position, tail,
license plate and instrument
panel lights turn on.
3 The headlights and all lights
listed above (except daytime
running lights) turn on.
4 The daytime running lights
turn on. ( P.153)
■AUTO mode can be used when
The engine switch is in ON.
■Daytime running light system
To make your vehicle more visible to
other drivers during daytime driving, the daytime running lights turn on automati-
cally whenever the engine is started and
the parking brake is released with the
headlight switch off or in the posi-
tion. (Illuminate brighter than the front
position lights.) Daytime running lights are not designed for use at night.
●When the turn signal indicators are flashing, the daytime running light on
the side that the turn signals are flash-
ing will turn off.
●When the emergency flashers are
flashing, both daytime running lights will turn off.
■Headlight control sensor
In the following situations, the automatic
light control system may not operate correctly.
●When an object is placed on the sen-sor or something which blocks the
sensor is affixed to the windshield
●When the surrounding area is lit by light other than natural light
■Automatic light off system
●When the light switch is in or :
The headlights turn off automatically if the engine switch is turned off.
●When the light switch is in : The
headlights and all lights turn off auto-
matically if the engine switch is turned
off.
Headlight switch
The headlights can be oper-
ated manually or automatically.
Operating instructions

171
4
4-5. EyeSight
Driving
NOTICE
• Side view
Monitors or other accessories
• Front view
Left-hand drive
Right-hand drive
●Do not place any objects on top of the instrument panel. The stereo
camera may not be able to detect
objects accurately and the EyeSight system may not func tion properly
due to reflections in the windshield.
For details, contact any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
A
●If the top of the instrument panel is polished with chemicals or other
substances, the stereo camera may
not be able to detect objects accu- rately and the EyeSight system
may not operate properly due to
reflections in the windshield.
●In case of replacement or repair, to
continue to use EyeSight function- ality, do not install a wiper blade
other than a genuine Toyota wiper
blade or a third party wiper blade that matches the quality of genuine
Toyota wiper blades.
Inferior parts can prevent the stereo camera from being able to detect
objects accurately, and the Eye-
Sight system may not operate prop- erly. Toyota and Toyota dealer(s)
are not liable for any damage that
may be caused by the use of parts other than genuine Toyota parts.
●Replace damaged wiper blades or worn wiper blade rubbers as soon
as possible. Using damaged wiper
blades or worn wiper blade rubbers may cause streaking on the wind-
shield. The stereo camera may not
be able to detect objects accurately and the EyeSight system may not
function properly due to streaks or
droplets remaining on the wind- shield.
●Do not install any accessories on the front side such as on the hood
or the grille. It may affect the cam-
era view and the system may not operate correctly.

2224-5. EyeSight
The alert sounds 1 short beep and (yellow) blinks or illuminates. At the
same time, the Pre-Collision Braking S ystem OFF indicator and the Lane
Departure Warning OFF indicator will illuminate. A message will also be
displayed on the meter display.
●If (yellow) is illuminating or blink-
ing, stop the vehicle in a safe location,
turn off the engine and then restart it.
●If the indicator continues illuminating
or flashing even after the engine has
been restarted, th e EyeSight system has a malfunction. In this case, all
EyeSight functions will be stopped.
Normal driving will still be possible.
However, contact any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer for an
inspection.
●If (yellow) illuminates or flashes,
the Reverse Automatic Braking (RAB)
system will not operate.
EyeSight malfunction and temporar y stop
If a malfunction is detected in the EyeSight system, the indicators in
the instrument panel and the meter display inform the driver of the
malfunction. Check the displayed contents and take the appropriate
action.
Malfunction (including position/angle misalignment of stereo
camera)
Warning messageCauseAction
“EyeSight OFF Check
Manual”
An EyeSight malfunction
or position/angle misalign-
ment of the stereo camera
has occurred.
Inspection and adjust-
ment is necessary. Con-
tact any authorized Toyota
retailer or Toyota author-
ized repairer, or any relia-
ble repairer.

285
6
6-1. Maintenance and care
Maintenance and care
 Remove dirt and dust using a
vacuum cleaner. Wipe dirty sur-
faces with a cloth dampened with
lukewarm water.
 If dirt cannot be removed, wipe it
off with a soft cloth dampened
with neutral detergent diluted to
approximately 1%.
Wring out any excess water from the
cloth and thoroughly wipe off remaining
traces of detergent and water.
■Shampooing the carpets
There are several commercial foam-
ing-type cleaners available. Use a sponge or brush to apply the foam. Rub
in overlapping circles. Do not use water.
Wipe dirty surfaces and let them dry.
Excellent results are obtained by keep- ing the carpet as dry as possible.
■Handling the seat belts
Clean with mild soap and lukewarm
water using a cloth or sponge. Also check the belts peri odically for exces-
sive wear, fraying or cuts.
■Meter visor
Do not place anything on top of meter visor. The color of the meter visor may
transfer.
Cleaning and protecting
the vehicle interior
Perform cleaning in a manner
appropriate to each compo-
nent and its material.
Protecting the vehicle inte-
rior
WA R N I N G
■Water in the vehicle
●Do not splash or spill liquid in the
vehicle.
Doing so may cause electrical com-
ponents, etc. to malfunction or catch
fire.
●Do not get any of the SRS compo-
nents or wiring in the vehicle interior
wet. ( P. 3 2 )
An electrical malfunction may cause
the airbags to deploy or not function
properly, resulting in death or serious injury.
■Cleaning the interior (especially instrument panel)
Do not use polish wax or polish
cleaner. The instrument panel may reflect off the windshield, obstructing
the driver’s view and leading to an
accident, resulting in death or serious injury.
NOTICE
■Cleaning detergents
●Do not use the following types of detergent, as they may discolor the
vehicle interior or cause streaks or
damage to painted surfaces:
• Non-seat portions: Organic sub-
stances such as benzene or gaso-
line, alkaline or acidic solutions, dye, and bleach
• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco-
hol
●Do not use polish wax or polish
cleaner. The instrument panel’s or
other interior part’s painted surface may be damaged.

2866-1. Maintenance and care
Remove dirt and dust using a
vacuum cleaner.
 Wipe off any excess dirt and dust
with a soft cloth dampened with
diluted detergent.
Use a diluted water solution of approxi-
mately 5% neutral wool detergent.
 Wring out any excess water from
the cloth and thoroughly wipe off
all remaining traces of detergent.
 Wipe the surface with a dry, soft
cloth to remove any remaining
moisture.
Allow the leather to dry in a
shaded and ventilated area.
NOTICE
●Do not use a chemical agent con-
taining silicone (highly-polymerized
silicon compound) when cleaning any of the electrical appliances
such as the air conditioning, all
switches and their surrounding areas.
If silicon (highly-polymerized silicon
compound) contacts these compo-
nents, it may cause the electrical appliances to malfunction.
■Preventing damage to leather surfaces
Observe the following precautions to
avoid damage to and deterioration of leather surfaces:
●Remove any dust or dirt from leather surfaces immediately.
●Do not expose the vehicle to direct sunlight for extended periods of
time. Park the vehicle in the shade,
especially during summer.
●Do not place items made of vinyl,
plastic, or containing wax on the upholstery, as they may stick to the
leather surface if the vehicle interior
heats up significantly.
■Water on the floor
Do not wash the vehicle floor with water.
Vehicle systems such as the audio
system may be damaged if water comes into contact with electrical
components such as the audio sys-
tem above or under the floor of the vehicle. Water may also cause the
body to rust.
■When cleaning the inside of the
windshield
Do not allow glass cleaner to contact the lens. Also, do not touch the lens.
(P.169)
■Cleaning the inside of the rear window
●Do not use glass cleaner to clean
the rear window, as this may cause damage to the rear window defog-
ger heater wires. Use a cloth damp-
ened with lukewarm water to gently wipe the window clean. Wipe the
window in strokes running parallel
to the heater wires.
●Be careful not to scratch or damage
the heater wires.
■When cleaning the instrument
panel
When small grains of sand and so
forth have gotten into instrument
panel’s surface and cannot be wiped away using a cloth, use a clay bar
without adding water. Forcibly trying
to wipe the surface clean with a brush or sponge may scratch the surface or
fragments of the cloth may be left in
the surface.
Cleaning the leather areas