2022 TOYOTA COROLLA HATCHBACK buttons

1844-2. Driving procedures
■Shift lock system
The shift lock system is a system to pre-
vent accidental operation of the shift
lever in starting. The shift lever can be shifted from P
only when the engine switch is in ON
and the brake pedal is being depressed.
■If the shift lever cannot be shifted from P
First, check whether the brake pedal is
being depressed. If the shift lever cannot be shifted with
your foot on the brake pedal, there may
be a problem with the shift lock system. Have the vehicle inspected by any
authorized Toyota retailer or Toyota
authorized repairer, or any reliable repairer immediately.
The following steps may be used as an
emergency measure to ensure that the shift lever can be shifted.
Releasing the shift lock:
1 Set the parking brake.
2 Turn the engine switch off.
3 Depress the brake pedal.
4 Ply the cover up with a flathead
screwdriver or equivalent tool. To prevent damaging the cover,
wrap the tip of the flathead screw-
driver with a tape.
5 Press and hold the shift lock override
button and then push the button on
the shift knob.
The shift lever can be shifted while the
both buttons are pressed.
 P.355
To enter 10-speed sport sequential
shiftmatic mode, sh ift the shift lever
to M position. Gear steps can then
be selected by operating the shift
lever, allowing yo u to drive in the
gear step of your choosing.
WA R N I N G
■To prevent an accident when
releasing the shift lock
Before pressing the shift lock override
button, make sure to set the parking
brake and depress the brake pedal. If the accelerator pedal is accidentally
depressed instead of the brake pedal
when the shift lock override button is pressed and the shift lever is shifted
out of P, the vehicle may suddenly
start, possibly leading to an accident resulting in death or serious injury.
Selecting the driving mode
Changing gears in the M
position

447
6
6-3. Using the storage features
Interior features
■Storing the luggage cover (vehicles with a dual level deck board)
When the dual level deck board is in the
upper position, the luggage cover can be stored under the deck board.
■Using the luggage cover
Pull out the luggage cover and
engage it to the anchors.
■Removing the luggage cover
Front
Push the left and right buttons of
the luggage cover unit.
Rear
Pull the left or right side bracket
down to disengage it. Then disen-
gage the other 3 brackets.Luggage cover (wagon) (if
equipped)
WA R N I N G
■When installing the luggage
cover
Make sure that the luggage cover is securely installed. Failure to do so
may result in seri ous injury in the
event of sudden braking or a collision.
■Caution for the luggage cover
●Do not place anything on the lug- gage cover to avoid death or seri-
ous injury.
●Do not allow children to climb on
the luggage cover. Climbing on the
luggage cover could result in dam- age to the luggage cover, possibly
causing death or serious injury to
the child.

4486-3. Using the storage features
■Using the partition net
Front position
1 Fold the rear seatbacks down.
( P.142)
2 Install the partition net unit to the
anchors on the right seatback.
When the anchors are engaged,
slide the partition net unit left-
ward.
3 Open the anchor covers on both
sides.
4 Pull out the net, push in the left
and right hooks and engage
them to the anchors.
If the net is pulled out slowly, it may lock
partway. To pull it out fully, allow the net
to roll back slightly then pull it out again.
Rear position
1 Install the partition net unit
behind the rear seats to the
anchors on the side deck.
When the partition net unit is secured, the lock release buttons are pushed in
and the red marking on the button's
sidewall is not visible.
2 Open the anchor covers on both
sides.
Partition net (if equipped)

449
6
6-3. Using the storage features
Interior features
3 Pull out the net, push in the left
and right hooks and engage
them to the anchors.
■Removing the partition net
Front position
Slide the partition net unit rightward
to disengage the anchors and lift it.
After removing the partition net unit,
return the rear seat backs to their origi-
nal position.
Rear position
Push the left and right lock release
buttons and lift up the partition net
unit.
■Locking of the partition net partway when pulled out
The partition net is designed to lock
partway, at the length suited for use in the rear position, when pulled out slowly.
(Quickly pulling out the partition net will
allow it to be pulled out to its full length.)
To release the lock: allow the net to roll
back slightly then pull it out again.
WA R N I N G
■When installing the partition net
Make sure that the partition net unit is
securely installed. Failure to do so may result in seri ous injury in the
event of sudden braking or a collision.
■When using the partition net
Make sure that the hooks are
engaged in the correct position on the anchors. Failure to do so may result
in serious injury in the event of sud-
den braking or a collision.