2022 SUZUKI JIMNY change time

FOREWORD
This manual should be considered as a permanent part of the vehicle and should remain with the vehicle when resold or oth­erwise transferred to a new owner or oper­ator. Please read this manual carefully before operating your new SUZUKI vehicle and review the manual from time to time. It contains important information on safety, operation and maintenance.
SUZUKI MOTOR CORPORATION
All information in this manual is based on the latest product information avail­able at the time of publication. Due to improvements or other changes1 there may be discrepancies between informa­tion in this manual and your vehicle. SUZUKI MOTOR CORPORATION reserves the right to make production changes at any time, without notice and without incurring any obligation to make the same or similar changes to vehicles previously built or sold.
This vehicle may not comply with stan­dards or regulations of other countries. Before attempting to register this vehi­cle in any other country, check all appli­cable regulations and make any necessary modifications.
NOTE: Please see the warning label named "Air­bag symbol meaning" in "BEFORE DRIV­ING" section for information on front airbag
protection.
IMPORTANT
A WARNING/ A CAUTION/NOTICE/ NOTE Please read this manual and follow its instructions carefully. To emphasize spe­cial information, the symbol A and the words WARNING, CAUTION, NOTICE and NOTE have special meanings. Pay particular attention to messages high­lighted by these signal words:
A WARNING
Indicates a potential hazard that could result in death or serious injury.
A CAUTION
Indicates a potential hazard that could result in minor or moderate
injury.
NOTICE
Indicates a potential hazard that could result in vehicle damage.
NOTE: Indicates special information to make maintenance easier or instructions clearer.

BEFORE DRIVING
Clock
The display (B) shows the time.
To change the lime indication: 1) Push the trip meter selector knob (1) and the indicator selector knob (2) together. 2) To change the hour indication, turn _the indicator selector knob (2) left or nght repeatedly when the hour indication · blinks. To change the hour indication quickly, turn and hold the indicator selector knob (2). To set the hour indi­cation, push the indicator selector knob (2) and the minute indication will blink. 3) To change the minute indication, turn the indicator selector knob (2) left or right repeatedly when the minute indi­cation blinks. To change the minute indication quickly, turn and hold the indicator selector knob (2). To set the minute indication, push the indicator selector knob (2).
To select 12124H format, refer to "Setting mode"-in this section.
A WARNING
If you attempt to adjust the display while driving, you could lose control of the vehicle. Do not attempt to adjust the display while driving.
2-19
Thermometer
The display (A) shows the thermometer. The thermometer indicates the outside temperature.
, ,:la)
Cocl#}
78RB02089
If the outside temperature drops to freez­ing condition, the mark (a) will appear on the display.
NOTE: The outside temperature indication is not the actual outside temperature when driving at low speed, or when stopped. If there is something wrong with the ther­mometer, or just after the ignition switch is tumed to "ON" position, the display may not indicate the outside tempera­ture.
When the display (E) shows the driving range, you can change the unit of tem­perature. To change the unit of temperature, while pushing and holding the trip meter selector knob (1 ), turn the indicator selector knob (2).
-----------
2 5 oc (Initial setting)
78RB02092
Selector position (for Automatic
transmission vehicles)/ Gearshift
indicator (if equipped)/ Rear pas­
senger's seat belt reminder (if equipped)
I EXAMPLE
□ 52RM21360

(For "L/100km" or 11km/L11 setting) To change the unit of average fuel con­sumption, while pushing and holding the trip meter selector knob (1 ), turn the indica­tor selector knob (2).
NOTE:
AVG.
i;11-iu1ookm I..U-1
(Initial setting)
68PH02207
When you change the units that average fuel consumption is displayed in, the instantaneous fuel consumption units will be changed automaticaf/y.
Driving range If you selected driving range the last time you drove the vehicle, the display indicates "---" for a few seconds and then indicates the current driving range when the ignition switch is turned "ON".
The driving range shown in the display is the approximate distance you can drive until the fuel gauge indicates "E", based on current driving conditions.
When the low fuel warning light comes on, the display"---" will appear.
If the low fuel warning light comes on, fill the fuel tank immediately regardless of the value of driving range shown in the display.
When you refuel, the driving range is updated. However, if you only add a small amount of fuel, the correct value will not be displayed.
NOTE: ff you refuel when the ignition switch is in "ON", the driving range may not indicate the correct value. When you reconnect the terminals to the lead-acid battery, the value of driving range will be shown after driving for a while.
BEFORE DRIVING
Fuel gauge
The display (F) shows the fuel gauge.
Refer to "Fuel gauge" in this section.
2-22

To switch to the setting mode 1) Push and hold the information switch (1) when the vehicle is stationary. 2) After the display of setting mode is shown, select the setting item that you want to change by turning the indicator selector knob (2) left or right. Refer to "Setting mode" in this section for details.
NOTE: If you switch to the setting mode while either of the following items is shown on the information display, the current value will be reset. If you do not want to reset its value, push the indicator selector knob (2) quickly beforehand and switch to the other item. Average fuel consumption • Driving time • Average speed
To exit the setting mode 1) To exit the setting mode, select "Back" and push the indicator selector knob (2). 2) Push the information switch (1) quickly.
NOTE: You can exit the setting mode by either of the following operations: Tum the ignition switch to ';,'\CC" or "LOCK" position. • Start driving your vehicle.
Information display
The information display is shown when the ignition switch is in "ON" position.
(A) (B)
(C)
(D) (E) (F)
(G)
(1) Information display
(1)
78RB02033
BEFORE DRIVING
78RB02039
(2) Trip meter selector knob (3) Indicator selector knob
The information display shows the follow­ing information.
Display (A) Clock
Display (B) Thermometer
Display (C) Warning and indicator messages I Fuel consumption / Driving range / Average speed / Driving time Display (D) Selector position (for Automatic transmis­sion models)/ Gear position (for Automatic transmission models) / Gearshift indicator (if equipped)
2-28

BEFORE DRIVING
Display (E) Trip meter I Rear passenger's seat belt reminder (if equipped)
Display (F) Odometer
Display (G) Fuel gauge
52RS20420
When the ignition switch is turned "ON", the message shown in the above illustra­tion will appear on the display for several seconds. Some warning and indicator messages may appear on the display when the igni­tion switch is in "ACC" or "LOCK".
2-29
Clock
When the ignition switch is in "ON", the dis­
play (A) shows the time.
To set the clock, follow "Setting mode" instructions in this section.
,A WARNING
If you attempt to adjust the display while driving, you could lose control of the vehicle. Do not attempt to adjust the display while driving.
Thermometer
When the ignition switch is "ON", the dis­play (B) shows the thermometer. The thermometer indicates the outside temperature.
-3°c
78RB02040
If the outside temperature nears freezing condition, the mark (a) will appear on the display.
NOTE: The outside temperature indication is not the actual outside temperature when driving at low speed, or when stopped. If there is something wrong with the ther­mometer, or just after the ignition switch is turned "ON", the display may not indi­cate the outside temperature.
When the display (C) shows the driving range, you can change the unit of tem­perature. To change the unit of temperature, refer to "Setting mode" in this section.
25°(
77 °F
(Initial setting)
52RM20880

BEFORE DRIVING
Instantaneous fuel consumption The display shows instantaneous fuel con­sumption with a bar graph only when the vehicle is moving.
NOTE: The display does not show the bar graph unless the vehicle is moving. Depending on the vehicle's specification, the fuel consumption units of initial set­ting are indicated as U100km, km/L or MPG (UK). The indicated maximum value of instan­taneous fuel consumption is one of the followings. No more than the maximum value will be indicated on the display even if the actual instantaneous fuel consumption is higher. -For U100km setting: 30 -For km/L setting: 50 -For MPG (UK) setting: 80 The indication on the display may be delayed if fuel consumption is greatly affected by driving conditions. The display shows estimated values. Indications may not be the same as actual values.
2-31
Average fuel consumption If you previously selected average fuel consumption setting, the display shows average fuel consumption from the last reset to the present when the ignition switch is turned "ON".
NOTE: When you reconnect the terminals to the lead-acid battery, the value of average fuel consumption will be shown after driving for a period of time.
You can select the timing to reset the value of average fuel consumption by one of the following three methods; Reset after refuel: the value of average fuel consumption will be reset automati­cally by refueling. Reset with trip meter A: the value of average fuel consumption will be reset automatically by resetting trip meter A. Reset manually: the value of average fuel consumption will be reset by push­ing and holding the indicator selector knob (3) when the display indicates the average fuel consumption.
To change the timing to reset the value of average fuel consumption, refer to "Setting mode" in this section.
NOTE: If you add only a small amount of fuel when you select "Reset after refuel", the average fuel consumption value may not be reset.
Driving range If you selected driving range the last time you drove the vehicle, the display indicates "---" for a few seconds and then indicates the current driving range when the ignition switch is turned "ON".
The driving range shown in the display is the approximate distance you can drive until the fuel gauge indicates "E", based on current driving conditions.
When the low fuel warning light comes on, the display "---" will appear.
If the low fuel warning light comes on, fill the fuel tank immediately regardless of the value of driving range shown in the display.
When you refuel, the driving range is updated. However, if you only add a small amount of fuel, the correct value will not be displayed.

BEFORE DRIVING
Setting mode
When the ignition switch is "ON" and the vehicle is stationary, you can enter the set­ting mode of the information display by pushing and holding the indicator selector knob (3) for a while.
To select the setting that you want to change, turn the indicator selector knob (3) left or right. To change the setting, push the indicator selector knob (3). To exit the setting mode, select "Back" and push the indicator selector knob (3).
78RB02096
NOTE: The currently selected setting item is sur­rounded by a frame.
2-33
NOTE: If you push and hold the indicator selec­tor knob (3) to enter the setting mode when the display (CJ shows average fuel consumption or average speed, driving time, the value will be reset simultane­ously. If you do not want to reset the value, push the indicator selector knob quickly to switch the indication of the dis­play. If you turn the ignition switch or start to move the vehicle when the display is in the setting mode, the setting mode will be canceled automatically.
Distance unit (Odometer I trip meter I driving range I average speed distance unit setting) You can change the units in which odome­ter I trip meter I driving range I average speed distance is displayed.
Fuel economy (Fuel consumption unit setting) You can change the units that fuel con­sumption is displayed in.
Language You can change the language of the infor­mation display.
Fuel reset (Average fuel consumption reset setting) You can change when the value of aver­age fuel consumption is reset.
Temperature (Temperature unit setting) You can change the units that temperature is displayed in. To change the temperature unit, select "Temperature" in "Setting mode". Then, select "°C" or "°F".
NOTE: When you change the units that tempera­ture is displayed in, the automatic heating and air conditioning system temperature display units will be changed automatically.
Clock setting (Adjusting the clock) • Adjust the clock by selecting "Clock set­ting" in "Setting mode". Then, select "Adjust clock". To change the hour indication, turn the indicator selector knob (3) left or right repeatedly when the hour indication appears as reversed color. To change the hour indication quickly, turn and hold indicator selector knob (3). To set the hour indication, push the indicator selec­tor knob (3) and the minute indication appears as reversed color. To change the minute indication, turn the indicator selector knob (3) left or right repeatedly when the minute indication appears as reversed color. To change the minute indication quickly, turn and hold indicator selector knob (3). To set the minute indication, push the indicator selector knob (3).

(Selecting 12H/24H format) Switch the time indication between 12-hour and 24-hour format by selecting "Clock setting" in "Setting mode". Then, select "12H" or "24H".
Door lock (Door unlock setting) You can choose either once or twice oper­ation(s) to unlock all doors (including the tailgate) by turning the key or operating the keyless entry system transmitter.
You can also turn off or on the buzzer sound when the door(s) is (are) locked or unlocked.
Lights (Lane change setting) The turn signal and its indicator can be set whether they flash three times even if you return the turn signal control lever shortly after operating it. To change the lane change setting, select "Lane change" in "Setting mode". Then, select "ON" or "OFF" If you want to change the number of flashing, consult a SUZUKI dealer.
Guide me light setting (Light setting) (if equipped) You can change the lighting time of "To car" function or "To home" function.
Oil change (Oil life monitoring system reset setting) (if equipped) The oil life monitoring system must be reset after changing the engine oil and oil filter. To reset the system, push and hold the indicator selector knob (3) for a while.
TPMS (Tyre pressure monitoring system set­ting) (if equipped) You can check the current tyre pressure on the information display. You can set one of the initial values of tyre pressure below that are indicated on the tyre information label. -Comfort Mode -Load Mode
Refer to "Tyre pressure monitoring system (TPMS)" in the "OPERATING YOUR VEHI­CLE" section for details.
Traffic sign recognition (Traffic sign recognition setting) (if equipped) If you select "ON" the traffic sign recogni­tion function can be activated.
Refer to "Traffic sign recognition" in the "OPERATING YOUR VEHICLE" section for details.
BEFORE DRIVING
Default (Initialization setting) If you select "YES" and push the indicator selector knob (3), all settings will be reini­tialized.
2-34