2022 SUZUKI CELERIO key

2-7
BEFORE DRIVING
76MH1-74E
76MH1-74E
Security System (if equipped)
The security system is armed in about 5 seconds after you lock all doors (includingthe tailgate) by using the keyless entry sys- tem transmitter. Once the system is armed, any attempt toopen a door by using any other means (*) than the keyless entry system transmitter, or open the engine hood, will cause thealarm to be triggered. * These means include the following:–The key – The lock knob on a door – The central door locking switch
Also, in case that you have set the shocksensor to enabled state and set sensitivity of the pre-warning function and full blastwarning function to a level other than 0, the alarm will be triggered if any attempt to tamper with the vehicle. The shock sensorcan be selected enabled or disabled state, and sensitivity of each warning can be adjusted as desired. To set the shock sen-sor, ask your MARUTI SUZUKI dealer or use the setting mode of the information display.
NOTE: • The default setting of the shock sensoris in the disabled state. Set to the enabled state and adjust sensitivity of each warning according to your prefer- ence. For details on how to use the infor-mation display, refer to “Information Display” in this section.• Your dealer may have already set theshock sensor of the vehicle to theenabled state before you purchase it. Consult your dealer for further informa-tion.
NOTE:• The security system generates alarmswhen any of the predetermined condi-tions is met. However, the system doesnot have any function of blocking unau- thorized entry into the vehicle.• Always use the keyless entry systemtransmitter to unlock the doors when thesecurity system has been armed. Using a key instead will trigger the alarm.• If a person who does not know the secu-rity system is going to drive the vehicle,we recommend you explain the systemand its operation to the person, or dis- able the system beforehand. Mistakenly triggering the alarm may cause a nui-sance to others.• Even if the security system is armed,you should still be careful to guardagainst theft. Do not leave money or things of value in the vehicle.
How to arm the security system
(when enabled)Lock all doors (including the tailgate) using the keyless entry system transmitter. Thesecurity system indicator (1) will start blink- ing rapidly, and the security system will be armed in about 5 seconds.While the system is being armed, the indi- cator continues to blink at intervals of approximately 2 seconds.
With tachometer
76MH0B001
(1)
18

2-8
BEFORE DRIVING
76MH1-74E
76MH1-74E
Without tachometer
76MH0B002
NOTE: • To prevent the alarm from being acci-dentally triggered, avoid arming it while anyone remains inside the vehicle. The alarm will be triggered if any person inside opens the door or engine hood, orswings the vehicle (if the shock sensor is in the enabled state).• The security system is not armed whenall doors are locked using the key fromoutside, or using the door lock knobs or the central door locking switch frominside.• If any door is not operated within approx-imately 30 seconds after the doors havebeen unlocked using the keyless entry system transmitter, the doors are auto-matically locked again. When the doors are locked, the security system will be
armed in about 5 seconds if the system is in the enabled state.• If the security system indicator (1) blinkswhen the ignition switch is in the “ON”position, there may be something wrong with the security system. Ask your MAR-UTI SUZUKI dealer to inspect the sys- tem.
How to disarm the security systemSimply unlock the doors using the keyless entry system transmitter. The security sys-tem indicator will go out, indicating that the security system is disarmed.
How to stop the alarm Should the alarm be triggered accidentally, unlock the doors using the keyless entrysystem transmitter, or insert the key in the ignition switch and turn it to “ON” position. The alarm will then stop.
NOTE: • Even after the alarm has stopped, if youlock the doors using the keyless entry system transmitter, the security system will be rearmed with a delay of about 5seconds.• If you disconnect the battery while thesecurity system is in the armed conditionor the alarm is actually in operation, the alarm will be re-triggered when the bat- tery is then reconnected.• Even after the alarm has stopped at theend of the predetermined operation time,it will be triggered again if any of thedoors or engine hood is opened, or the
vehicle feels a shock (if the shock sen- sor is in the enabled state), without dis- arming the security system.
Checking whether the alarm has beentriggered during parkingIf the alarm was triggered and you then turn the ignition switch to “ON” position, the security system indicator will blink rapidlyfor about 8 seconds and a buzzer will beep 4 times during this period. If this happens, check whether the vehicle has been bro-ken into while you were away from it.
Enabling and disabling the security system The security system can be either enabled or disabled.
When enabled If any of the doors are opened withoutunlocking by the keyless entry system transmitter, all turn signal lights start to blink and the interior buzzer beeps inter-mittently. After 5 seconds, the siren will sound for about 27.5 seconds. The secu- rity system indicator continues to blinkduring this time. If the engine hood is opened, all turn sig-nal lights blink, and the siren sounds forabout 27.5 seconds. The security sys- tem indicator continues to blink during this time.
(If the shock sensor is in the enabled state) If the vehicle feels a shock, the sirensounds for about 2 seconds (pre-warn- ing). If the vehicle continues to feel a
(1)
19

2-11
BEFORE DRIVING
76MH1-74E
76MH1-74E
To open a window, push the top part of the switch and to close the window, lift up the top part of the switch.
The driver’s window has an “auto-down” featurefor added convenience (at toll booths or drive-through restaurants, for example). This means you can open the window without holding the window switch in the “Down” position. Press thedriver’s window switch completely down and release it. To stop the window before it reaches the bottom, pull the switch up briefly.
Lock switch
76MH0A024
The driver’s door also has a lock switch forthe passenger’s windows. When you pushin the lock switch, the passenger’s win- dows cannot be raised or lowered by oper- ating any of the switches (1), (2), (3) or (4).To restore normal operation, release the lock switch by pushing again.
NOTE:If you drive with one of the rear windows open, you may hear a loud sound causedby air vibration. To reduce the sound, open the driver’s or front passenger’s window, or narrow the rear window opening.
Mirrors
Inside Rearview MirrorYou can adjust the inside rearview mirrorby hand so as to see the rear of your vehi-cle in the mirror.
Ty p e 1
74LHT0235
Ty p e 2
68LMT0205
68LMT0206
(2) Day driving (3) Night driving
EXAMPLE
WA R N I N G
• You should always lock the pas-senger’s window operation whenthere are children in the vehicle. Children can be seriously injured if they get part of their body caughtby the window during operation.• To avoid injuring an occupant bywindow entrapment, be sure nopart of the occupant’s body such as hands or head is in the path of the electric windows when closingthem.• Always remove the ignition keywhen leaving the vehicle even ifonly for a short time. Also do not leave children alone in a parked vehicle. Unattended children coulduse the electric window switches and get trapped by the window.
(1)
(2)(3)
22

2-18
BEFORE DRIVING
76MH1-74E
76MH1-74E
80JS029
To lengthen, release the latch plate from the buckle, pull the latch plate (adjuster) in the direction of the arrow, at right angles tothe belt. The latch plate should then be refitted into the buckle and the belt tight- ened as previously described.
To unfasten the belt, press the release but- ton on the buckle catch.
80JS031
NOTE: To identify the center seat belt buckle and latch plate in the rear seat, “CENTER” ismarked on the buckle and latch plate of the center lap belt. The buckles are designed so a latch plate cannot be inserted into thewrong buckle.
Driver’s Seat Belt Reminder
(if equipped)
With tachometer
76MH028
Without tachometer
76MS013
When the driver doesn’t buckle his or her seat belt with the ignition switch in the “ON” position, the driver’s seat belt reminderlight in the instrument cluster will blink until the driver’s seat belt is buckled.
TO LOOSEN
Right angleEXAMPLE
WA R N I N G
It is absolutely essential that thedriver and passengers wear their seat belts at all times. Persons who arenot wearing seat belts have a much greater risk of injury if an accident occurs. Make a regular habit of buck-ling your seat belt before putting the key in the ignition.
EXAMPLE
29

2-22
BEFORE DRIVING
76MH1-74E
76MH1-74E
Child Restraint System for India
Child Restraint
The suitability of each passenger’s seat position for carriage of children and fitting of child restraint system is shown in the table below. Whenever you carry children up to 12 years of age, properly use the child restraints which conform to AIS 072, the standard for child restraints, referring to the table.
MASS GROUP
Seating position (or other site)
Fr on t PassengerRear OutboardRear CentreIntermediate OutboardIntermediate Centre
Group 0 Up to 10 kgXUXN.A.N.A.
Group 0+Up to 13 kgXUXN.A.N.A.
Group I9 to 18 kgXUXN.A.N.A.
Group II15 to 25 kgXUXN.A.N.A.
Group III22 to 36 kgXUXN.A.N.A.
Key of letters to be inserted in the above table: U =Suitable for ‘universal’ category restraints approved for use in this mass group X =Seat position not suitable for children in this mass group N.A = Seat position not available for children in this mass group. NOTE: ‘universal’ is the category in the AIS 072.
33

2-41
BEFORE DRIVING
76MH1-74E
76MH1-74E
Immobilizer System Light
80JM122
When the ignition switch is turn to the “ON” position, this light comes on briefly so you can check that the light is working. If thislight brinks with the ignition switch is turn to the “ON” , the engine will not start.
NOTE: If this light blinks, turn the ignition switch to the “LOCK” position, then turn it back to the “ON” position. If the light still blinks with the ignition switchturned to the “ON” position, there may be something wrong with your key or with the immobilizer system. Ask your MARUTISUZUKI dealer to inspect the system.
Open Door Warning Light
54G391
This light remains on until all doors (includ-ing the tailgate) are completely closed.
If any door (including the tailgate) is open when the vehicle is moving, a ding sounds to remind you to close all doors completely.
Low Fuel Warning Light
54G343
If this light comes on, fill the fuel tankimmediately.
When this light comes on, a ding sounds once to remind you to fill the fuel. If you do not fill the fuel, a ding sounds every time when the ignition switch isturned to the “ON” position.
NOTE: The activation point of this light varies depending on road conditions (for exam- ple, slope or curve) and driving conditionsbecause of fuel moving in the tank.
Turn Signal Indicators
50G055
When you turn on the left or right turn sig- nals, the corresponding green arrow on the instrument panel will flash along with therespective turn signal lights. When you turn on the hazard warning switch, both arrows will flash along with all of the turnsignal lights.
Main Beam (high beam) Indicator
Light
50G056
This indicator comes on when headlight main beams (high beams) are turned on.
Security System Indicator
(if equipped)
82K269
For details about the security system, referto “Security System” in this section.
52

3-2
OPERATING YOUR VEHICLE
76MH1-74E
76MH1-74E
NOTE: It is normal for water to drip from the air conditioning system after use.
4) Make sure the hood is fully closed and latched.5) Check the headlights, turn signal lights, brake lights and horn for proper opera- tion.6) Adjust the seat and head restraint (if equipped). 7) Check the brake pedal and the parkingbrake lever. 8) Adjust the mirrors. 9) Make sure that you and all passengershave properly fastened your seat belts. 10)Make sure that all warning lights come on as the key is turned to the “ON” posi-tion. 11)Check all gauges. 12)Make sure that the BRAKE SYSTEMWARNING light turns off when the parking brake is released.
Once a week, or each time you fill your fuel tank, perform the following under-hood checks:
1) Engine oil level 2) Coolant level3) Brake fluid level 4) Windshield washer fluid level 5) Battery solution level6) Hood latch operation Pull the hood release handle inside the vehicle. Make sure that you cannotopen the hood all the way without
releasing the secondary latch. Be sure to close the hood securely after check- ing for proper latch operation. See “Alllatches, hinges & locks” of “CHASSIS AND BODY” in the “Periodic Mainte- nance Schedule” in the “INSPECTIONAND MAINTENANCE” section for lubri- cation schedule.
Once a month, or each time you fill your fuel tank, check the tire pressure using a tire pressure gauge. Also check the tirepressure of the spare tire.
Engine Oil Consumption
It is normal for the engine to consume some engine oil during normal vehicle operation.
The amount of engine oil consumed depends on the viscosity of the oil, thequality of the oil and the conditions the vehicle is driven under. More oil is consumed during high-speeddriving and when there is frequent acceler- ation and deceleration. Under high loads, your engine also will consume more oil.A new engine also consumes more oil, since its pistons, piston rings and cylinder
walls have not yet become conditioned. New engines reach the normal level of oil consumption only after approximately 5000km (3000 miles) driving.
Oil consumption: Max. 1.0 L per 1000 km (1 Qt. per 600 miles)
When judging the amount of oil consump- tion, note that the oil may become diluted and make it difficult to accurately judge thetrue oil level. As an example, if a vehicle is used for repeated short trips, and consumes a nor-mal amount of oil, the dipstick may not show any drop in the oil level at all, even after 1000 km (600 miles) or more of driv-ing. This is because the oil is gradually becoming diluted with fuel or moisture, making it appear that the oil level has notchanged. You should also be aware that the diluting ingredients evaporate out when the vehicleis subsequently driven at high speeds, such as on an expressway, making it appear that oil is excessively consumedafter high-speed driving.
WA R N I N G
Make sure the hood is fully closed and latched before driv ing. If it is not, it can fly up unexpectedly duringdriving, obstructing your view and resulting in an accident.
61

3-3
OPERATING YOUR VEHICLE
76MH1-74E
76MH1-74E
Ignition Switch
65D611
52KM052
The ignition switch has the following four positions: LOCK This is the normal parking position. It is theonly position in which the key can be removed.
60G033
You must push in the key to turn it to the “LOCK” position. It lo cks the ignition, and prevents normal use of the steering wheel after the key is removed.
To release the steering lock, insert the key and turn it clockwise to one of the other positions. If you have trouble turning thekey to unlock the steering, try turning the steering wheel slightly to the right or left while turning the key.
ACC Accessories such as the radio can oper-ate, but the engine is off.
ON This is the normal operating position. All electrical systems are on.
START This is the position for starting the engine using the starter motor. The key should bereleased from this position as soon as the engine starts.
Ignition key reminder (if equipped) A buzzer sounds intermittently to remind you to remove the ignition key if it is in theignition switch when the driver’s door is opened.
81A297S
WA R N I N G
To avoid possible injury, do not oper- ate controls by reaching through thesteering wheel.
EXAMPLE
Turn to “LOCK”
Push
WA R N I N G
• Never remove the ignition keywhile the vehicle is moving. The steering wheel will lock and you will not be able to steer the vehicle.(Continued)
62