2022 RAM 1500 ECU

88GETTING TO KNOW YOUR VEHICLE
TAILGATE REMOVAL
NOTE:Removing the tailgate will disable the rearview
camera function.
To remove the tailgate, follow the instructions
below:

1. Open the tailgate to a 45° angle.

2. Lift up on the right side of the tailgate, lifting it
off of the pivot.

Lift Right Side Off Of Pivot

3. Without latching, rotate the tailgate to nearly closed. Then, while providing support to the
tailgate, slide it slowly to the right, removing
the tailgate from the left pivot.
NOTE:Rest the tailgate on the bumper so that the entire
tailgate is secure and supported.

Slide Tailgate To The Right

4. Let the tailgate rest on the support cables while having the tailgate naturally slide
forward on the bumper.
Tailgate Only Supported By Cables

5. Remove the connector bracket from the sill by pushing inward in the locking tab.

Connector Bracket Location

WARNING!
For vehicles equipped with a multifunction
tailgate, the tailgate weighs 115 lb (52 kg) and
should be removed by at least two people. Injury
to the customer or damage to the tailgate may
occur if one person tries to remove the
multifunction tailgate.

22_DT_OM_EN_USC_t.book Page 88

GETTING TO KNOW YOUR VEHICLE93
BED RAIL TIE-DOWN SYSTEM —
I
F EQUIPPED
There are two adjustable cleats on each side of the
bed that can be used to assist in securing cargo.

Adjustable Cleats

Each cleat must be located and tightened down in
one of the detents, along either rail, in order to
keep cargo properly secure. To move the cleat to any position on the rail, turn
the nut counterclockwise, approximately three
turns. Then pull out on the cleat and slide it to the
detent nearest the desired location. Make sure the
cleat is seated in the detent and tighten the nut.

Adjustable Cleat Assembly

Cleat Removal (Standard Box Rail)
To remove the cleats from the utility rail, slide the
cleat forward to access the cut out at the end of the
box rail, then remove the cleat.
Slide Cleat Forward To Remove

Cleat Removal (With Tonneau Cover)
To remove the cleats from the utility rail, remove
the end cap screw located in the center of the end
cap, using a #T30 Torx head driver. Remove the
end cap and slide the cleat off the end of the rail.

End Cap Screw Location With Tonneau Cover

CAUTION!
The maximum load per cleat should not exceed
250 lb (113 kg), or 500 lb (227 kg) total per rail,
and the angle of the load on each cleat should
not exceed 45 degrees above horizontal, or
damage to the cleat or cleat rail may occur.
1 — Utility Rail Detent
2 — Cleat Retainer Nut
3 — Utility Rail Cleat
2

22_DT_OM_EN_USC_t.book Page 93

94GETTING TO KNOW YOUR VEHICLE
(Continued)
Cleat Removal (Without Tonneau Cover)
Remove the end cap by pushing upward on the
release button located beneath the end cap while
pulling the cap away from the rail. The cleat can
now be removed by sliding it off the end of the rail.

End Cap Release Button Without Tonneau Cover
Pull End Cap Away From Rail

RAMBOX — IF EQUIPPED
The RamBox system is an integrated pickup box
storage and cargo management system consisting
of three features:
Cargo storage bins
Cargo divider
Bed rail tie-down system Ú page 93
NOTE:Bed rail tie-down system is also available for
vehicles not equipped with a RamBox.
LOCKING AND UNLOCKING RAMBOX
Push and release the lock or unlock button on the
key fob to lock and unlock all doors, the tailgate
and the RamBox Úpage 19. To unlatch the
storage bin manually, insert the emergency key
into the keyhole and turn clockwise. Always return
the key to the upright (vertical) position before
removing it from the keyhole.
RAMBOX CARGO STORAGE BINS
Cargo storage bins are located on both sides of the
pickup box. The cargo storage bins provide
watertight, lockable, illuminated storage for up to
150 lb (68 kg) of evenly distributed cargo.

RamBox Cargo Storage Bins

CAUTION!
Ensure cargo bin lids are closed and latched
before moving or driving vehicle.
Loads applied to the top of the bin lid should
be minimized to prevent damage to the lid and
latching/hinging mechanisms.
Damage to the RamBox bin may occur due to
heavy/sharp objects placed in bin that shift
due to vehicle motion. In order to minimize
potential for damage, secure all cargo to
prevent movement and protect inside
surfaces of bin from heavy/sharp objects with
appropriate padding.
CAUTION!

22_DT_OM_EN_USC_t.book Page 94

GETTING TO KNOW YOUR VEHICLE95
To open a storage bin with the RamBox unlocked,
push and release the button located on the lid. The
RamBox lid will open upward to allow hand access.
Lift the lid to fully open.
NOTE:RamBox will not open when the button is pushed if
the RamBox is locked.
RamBox Button And Keyhole Lock
The interior of the RamBox will automatically
illuminate when the lid is opened. The timing can
be adjusted within Uconnect Settings
Úpage 234.
Cargo bins feature two removable drain plugs (to
allow water to drain from bins). To remove plug,
pull up on the edge. To install, push plug downward
into drain hole.

RamBox Drain Plug Removal

NOTE:Provisions are provided in the bins for cargo
dividers. These accessories (in addition to other
RamBox accessories) are available from Mopar®.
CAUTION!
Failure to follow the following items could cause
damage to the vehicle:
Assure that all cargo inside the storage bins is
properly secured.
Do not exceed cargo weight rating of 150 lb
(68 kg) per bin.
1 — Keyhole Lock
2 — Button
CAUTION!
Leaving the lid open for extended periods of time
could cause the vehicle battery to discharge. If
the lid is required to stay open for extended
periods of time, it is recommended that the bin
lights be turned off manually using the on/off
switch.
2

22_DT_OM_EN_USC_t.book Page 95

96GETTING TO KNOW YOUR VEHICLE
(Continued)
If equipped, a 115 Volt (400 Watts Maximum)
inverter may be located inside the RamBox of your
vehicle. The inverter can be turned on by the
Instrument Panel Power Inverter switch located to
the left of the steering wheel. The RamBox inverter
can power cellular phones, electronics and
other low power devices requiring power up to
400 Watts. Certain video game consoles exceed
this power limit, as will most power tools.

RamBox Power Inverter

The Instrument Panel Power Inverter switch is only
found on vehicles equipped with a RamBox. The
switch only controls on/off operation of the power
outlet in the RamBox; it does not control on/off
operation of the power outlets located inside the
cabin of the vehicle.
Instrument Panel Power Inverter Switch

RAMBOX SAFETY WARNING
Carefully follow these warnings to help prevent
personal injury or damage to your vehicle:
RamBox Emergency Release Lever
As a security measure, an Emergency Release
Lever is built into the storage bin cover latching
mechanism.
In the event of an individual being locked inside
the storage bin, the storage bin cover can be
opened from inside of the bin by pulling on the
glow-in-the-dark lever attached to the storage bin
cover latching mechanism.

Emergency Release Lever

WARNING!
Always close the storage bin covers when your
vehicle is unattended.
Do not allow children to have access to the
storage bins. Once in the storage bin, young
children may not be able to escape. If trapped
in the storage bin, children can die from suffo -
cation or heat stroke.
In an accident, serious injury could result if the
storage bin covers are not properly latched.
Do not drive the vehicle with the storage bin
covers open.
Keep the storage bin covers closed and
latched while the vehicle is in motion.
Do not use a storage bin latch as a tie-down.
WARNING!

22_DT_OM_EN_USC_t.book Page 96

GETTING TO KNOW YOUR VEHICLE97
BED DIVIDER — IF EQUIPPED
The bed divider has two functional positions:
Divider Position
Storage Position
Divider Position
The divider position is intended for managing your
cargo and assisting in keeping cargo from moving
around the bed. There are 11 divider slots along
the bed inner panels which allow for various
positions to assist in managing your cargo.
To install the bed divider into a divider position,
perform the following:

1. Make sure the center handle is unlocked
using the vehicle key and rotate the center
handle vertically to release the divider side
gates.
Center Handle And Lock

2. With the side gates open, position the divider so the outboard ends align with the intended
slots in the sides of the bed.
Aligning Gate To Slots

3. Rotate the side gates closed so that the outboard ends are secured into the intended
slots of the bed.
4. Rotate the center handle horizontally to secure the side gates in the closed position.

Side Gates Closed

1 — Center Handle Lock
2 — Handle
3 — Unlocked Position
4 — Locked Position
2

22_DT_OM_EN_USC_t.book Page 97

98GETTING TO KNOW YOUR VEHICLE
5. Lock the center handle to secure the panel into place.
Storage Position
The storage position for the bed divider is at the
front of the truck bed which maximizes the bed
cargo area when not in use.
To install the bed divider into the storage position,
perform the same steps as you would for the
divider position, except position the divider fully
forward in the bed against the front panel.

Storage Position

The outboard ends should be positioned in front of
the cargo tie-down loops.
Cargo Tie-Down Loop

TRI-FOLD TONNEAU COVER — IF EQUIPPED
The Tri-Fold Tonneau Cover can be installed on the
truck bed to protect your gear and cargo.
TONNEAU COVER COMPONENTS

Folded Tonneau Components

1 – Stowage Strap
2 – Tonneau Bumper Folded

22_DT_OM_EN_USC_t.book Page 98

GETTING TO KNOW YOUR VEHICLE99

Tonneau Cover Latch Components Position One
(Front Latches Latched And Stowage Straps Secured)
Position Two (Front And Rear Latches Latched)

TRI-FOLD TONNEAU COVER FOLDING
F
OR DRIVING OR REMOVAL
To remove the Tonneau Cover use the following
steps:

1. Open the tailgate to access the rear pair of
Tonneau Cover latches located on the
underside of the Cover.

Location Of Rear Latches

1 — Handle
2 — Slide Locking Lever
3 — Locating Bumper
4 — Truck Flange Bead
5 — Latch Bumper
6 — J Hook
1 — Panel 1
2 — Panel 2
3 — Panel 3
2

22_DT_OM_EN_USC_t.book Page 99